diff options
Diffstat (limited to 'include/linux/mmc/sdio.h')
| -rw-r--r-- | include/linux/mmc/sdio.h | 159 |
1 files changed, 159 insertions, 0 deletions
diff --git a/include/linux/mmc/sdio.h b/include/linux/mmc/sdio.h new file mode 100644 index 0000000..47ba464 --- /dev/null +++ b/include/linux/mmc/sdio.h @@ -0,0 +1,159 @@ +/* + * include/linux/mmc/sdio.h + * + * Copyright 2006-2007 Pierre Ossman + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or (at + * your option) any later version. + */ + +#ifndef MMC_SDIO_H +#define MMC_SDIO_H + +/* SDIO commands type argument response */ +#define SD_IO_SEND_OP_COND 5 /* bcr [23:0] OCR R4 */ +#define SD_IO_RW_DIRECT 52 /* ac [31:0] See below R5 */ +#define SD_IO_RW_EXTENDED 53 /* adtc [31:0] See below R5 */ + +/* + * SD_IO_RW_DIRECT argument format: + * + * [31] R/W flag + * [30:28] Function number + * [27] RAW flag + * [25:9] Register address + * [7:0] Data + */ + +/* + * SD_IO_RW_EXTENDED argument format: + * + * [31] R/W flag + * [30:28] Function number + * [27] Block mode + * [26] Increment address + * [25:9] Register address + * [8:0] Byte/block count + */ + +/* + SDIO status in R5 + Type + e : error bit + s : status bit + r : detected and set for the actual command response + x : detected and set during command execution. the host must poll + the card by sending status command in order to read these bits. + Clear condition + a : according to the card state + b : always related to the previous command. Reception of + a valid command will clear it (with a delay of one command) + c : clear by read + */ + +#define R5_COM_CRC_ERROR (1 << 15) /* er, b */ +#define R5_ILLEGAL_COMMAND (1 << 14) /* er, b */ +#define R5_ERROR (1 << 11) /* erx, c */ +#define R5_FUNCTION_NUMBER (1 << 9) /* er, c */ +#define R5_OUT_OF_RANGE (1 << 8) /* er, c */ +#define R5_STATUS(x) (x & 0xCB00) +#define R5_IO_CURRENT_STATE(x) ((x & 0x3000) >> 12) /* s, b */ + +/* + * Card Common Control Registers (CCCR) + */ + +#define SDIO_CCCR_CCCR 0x00 + +#define SDIO_CCCR_REV_1_00 0 /* CCCR/FBR Version 1.00 */ +#define SDIO_CCCR_REV_1_10 1 /* CCCR/FBR Version 1.10 */ +#define SDIO_CCCR_REV_1_20 2 /* CCCR/FBR Version 1.20 */ + +#define SDIO_SDIO_REV_1_00 0 /* SDIO Spec Version 1.00 */ +#define SDIO_SDIO_REV_1_10 1 /* SDIO Spec Version 1.10 */ +#define SDIO_SDIO_REV_1_20 2 /* SDIO Spec Version 1.20 */ +#define SDIO_SDIO_REV_2_00 3 /* SDIO Spec Version 2.00 */ + +#define SDIO_CCCR_SD 0x01 + +#define SDIO_SD_REV_1_01 0 /* SD Physical Spec Version 1.01 */ +#define SDIO_SD_REV_1_10 1 /* SD Physical Spec Version 1.10 */ +#define SDIO_SD_REV_2_00 2 /* SD Physical Spec Version 2.00 */ + +#define SDIO_CCCR_IOEx 0x02 +#define SDIO_CCCR_IORx 0x03 + +#define SDIO_CCCR_IENx 0x04 /* Function/Master Interrupt Enable */ +#define SDIO_CCCR_INTx 0x05 /* Function Interrupt Pending */ + +#define SDIO_CCCR_ABORT 0x06 /* function abort/card reset */ + +#define SDIO_CCCR_IF 0x07 /* bus interface controls */ + +#define SDIO_BUS_WIDTH_1BIT 0x00 +#define SDIO_BUS_WIDTH_4BIT 0x02 + +#define SDIO_BUS_CD_DISABLE 0x80 /* disable pull-up on DAT3 (pin 1) */ + +#define SDIO_CCCR_CAPS 0x08 + +#define SDIO_CCCR_CAP_SDC 0x01 /* can do CMD52 while data transfer */ +#define SDIO_CCCR_CAP_SMB 0x02 /* can do multi-block xfers (CMD53) */ +#define SDIO_CCCR_CAP_SRW 0x04 /* supports read-wait protocol */ +#define SDIO_CCCR_CAP_SBS 0x08 /* supports suspend/resume */ +#define SDIO_CCCR_CAP_S4MI 0x10 /* interrupt during 4-bit CMD53 */ +#define SDIO_CCCR_CAP_E4MI 0x20 /* enable ints during 4-bit CMD53 */ +#define SDIO_CCCR_CAP_LSC 0x40 /* low speed card */ +#define SDIO_CCCR_CAP_4BLS 0x80 /* 4 bit low speed card */ + +#define SDIO_CCCR_CIS 0x09 /* common CIS pointer (3 bytes) */ + +/* Following 4 regs are valid only if SBS is set */ +#define SDIO_CCCR_SUSPEND 0x0c +#define SDIO_CCCR_SELx 0x0d +#define SDIO_CCCR_EXECx 0x0e +#define SDIO_CCCR_READYx 0x0f + +#define SDIO_CCCR_BLKSIZE 0x10 + +#define SDIO_CCCR_POWER 0x12 + +#define SDIO_POWER_SMPC 0x01 /* Supports Master Power Control */ +#define SDIO_POWER_EMPC 0x02 /* Enable Master Power Control */ + +#define SDIO_CCCR_SPEED 0x13 + +#define SDIO_SPEED_SHS 0x01 /* Supports High-Speed mode */ +#define SDIO_SPEED_EHS 0x02 /* Enable High-Speed mode */ + +/* + * Function Basic Registers (FBR) + */ + +#define SDIO_FBR_BASE(f) ((f) * 0x100) /* base of function f's FBRs */ + +#define SDIO_FBR_STD_IF 0x00 + +#define SDIO_FBR_SUPPORTS_CSA 0x40 /* supports Code Storage Area */ +#define SDIO_FBR_ENABLE_CSA 0x80 /* enable Code Storage Area */ + +#define SDIO_FBR_STD_IF_EXT 0x01 + +#define SDIO_FBR_POWER 0x02 + +#define SDIO_FBR_POWER_SPS 0x01 /* Supports Power Selection */ +#define SDIO_FBR_POWER_EPS 0x02 /* Enable (low) Power Selection */ + +#define SDIO_FBR_CIS 0x09 /* CIS pointer (3 bytes) */ + + +#define SDIO_FBR_CSA 0x0C /* CSA pointer (3 bytes) */ + +#define SDIO_FBR_CSA_DATA 0x0F + +#define SDIO_FBR_BLKSIZE 0x10 /* block size (2 bytes) */ + +#endif + |
