diff options
Diffstat (limited to 'include/linux/mfd/asic3.h')
| -rw-r--r-- | include/linux/mfd/asic3.h | 56 |
1 files changed, 28 insertions, 28 deletions
diff --git a/include/linux/mfd/asic3.h b/include/linux/mfd/asic3.h index 7e47cfb..6461a2a 100644 --- a/include/linux/mfd/asic3.h +++ b/include/linux/mfd/asic3.h @@ -45,39 +45,39 @@ struct asic3_platform_data { /* All offsets below are specified with this address bus shift */ #define ASIC3_DEFAULT_ADDR_SHIFT 2 -#define ASIC3_OFFSET(base, reg) (ASIC3_##base##_Base + ASIC3_##base##_##reg) +#define ASIC3_OFFSET(base, reg) (ASIC3_##base##_BASE + ASIC3_##base##_##reg) #define ASIC3_GPIO_OFFSET(base, reg) \ - (ASIC3_GPIO_##base##_Base + ASIC3_GPIO_##reg) + (ASIC3_GPIO_##base##_BASE + ASIC3_GPIO_##reg) -#define ASIC3_GPIO_A_Base 0x0000 -#define ASIC3_GPIO_B_Base 0x0100 -#define ASIC3_GPIO_C_Base 0x0200 -#define ASIC3_GPIO_D_Base 0x0300 +#define ASIC3_GPIO_A_BASE 0x0000 +#define ASIC3_GPIO_B_BASE 0x0100 +#define ASIC3_GPIO_C_BASE 0x0200 +#define ASIC3_GPIO_D_BASE 0x0300 #define ASIC3_GPIO_TO_BANK(gpio) ((gpio) >> 4) #define ASIC3_GPIO_TO_BIT(gpio) ((gpio) - \ (ASIC3_GPIOS_PER_BANK * ((gpio) >> 4))) #define ASIC3_GPIO_TO_MASK(gpio) (1 << ASIC3_GPIO_TO_BIT(gpio)) -#define ASIC3_GPIO_TO_BASE(gpio) (ASIC3_GPIO_A_Base + (((gpio) >> 4) * 0x0100)) -#define ASIC3_BANK_TO_BASE(bank) (ASIC3_GPIO_A_Base + ((bank) * 0x100)) - -#define ASIC3_GPIO_Mask 0x00 /* R/W 0:don't mask */ -#define ASIC3_GPIO_Direction 0x04 /* R/W 0:input */ -#define ASIC3_GPIO_Out 0x08 /* R/W 0:output low */ -#define ASIC3_GPIO_TriggerType 0x0c /* R/W 0:level */ -#define ASIC3_GPIO_EdgeTrigger 0x10 /* R/W 0:falling */ -#define ASIC3_GPIO_LevelTrigger 0x14 /* R/W 0:low level detect */ -#define ASIC3_GPIO_SleepMask 0x18 /* R/W 0:don't mask in sleep mode */ -#define ASIC3_GPIO_SleepOut 0x1c /* R/W level 0:low in sleep mode */ -#define ASIC3_GPIO_BattFaultOut 0x20 /* R/W level 0:low in batt_fault */ -#define ASIC3_GPIO_IntStatus 0x24 /* R/W 0:none, 1:detect */ -#define ASIC3_GPIO_AltFunction 0x28 /* R/W 1:LED register control */ -#define ASIC3_GPIO_SleepConf 0x2c /* +#define ASIC3_GPIO_TO_BASE(gpio) (ASIC3_GPIO_A_BASE + (((gpio) >> 4) * 0x0100)) +#define ASIC3_BANK_TO_BASE(bank) (ASIC3_GPIO_A_BASE + ((bank) * 0x100)) + +#define ASIC3_GPIO_MASK 0x00 /* R/W 0:don't mask */ +#define ASIC3_GPIO_DIRECTION 0x04 /* R/W 0:input */ +#define ASIC3_GPIO_OUT 0x08 /* R/W 0:output low */ +#define ASIC3_GPIO_TRIGGER_TYPE 0x0c /* R/W 0:level */ +#define ASIC3_GPIO_EDGE_TRIGGER 0x10 /* R/W 0:falling */ +#define ASIC3_GPIO_LEVEL_TRIGGER 0x14 /* R/W 0:low level detect */ +#define ASIC3_GPIO_SLEEP_MASK 0x18 /* R/W 0:don't mask in sleep mode */ +#define ASIC3_GPIO_SLEEP_OUT 0x1c /* R/W level 0:low in sleep mode */ +#define ASIC3_GPIO_BAT_FAULT_OUT 0x20 /* R/W level 0:low in batt_fault */ +#define ASIC3_GPIO_INT_STATUS 0x24 /* R/W 0:none, 1:detect */ +#define ASIC3_GPIO_ALT_FUNCTION 0x28 /* R/W 1:LED register control */ +#define ASIC3_GPIO_SLEEP_CONF 0x2c /* * R/W bit 1: autosleep * 0: disable gposlpout in normal mode, * enable gposlpout in sleep mode. */ -#define ASIC3_GPIO_Status 0x30 /* R Pin status */ +#define ASIC3_GPIO_STATUS 0x30 /* R Pin status */ /* * ASIC3 GPIO config @@ -137,7 +137,7 @@ struct asic3_platform_data { #define LED_AUTOSTOP (1 << 5) /* LED ON/OFF auto stop 0:disable, 1:enable */ #define LED_ALWAYS (1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */ -#define ASIC3_CLOCK_Base 0x0A00 +#define ASIC3_CLOCK_BASE 0x0A00 #define ASIC3_CLOCK_CDEX 0x00 #define ASIC3_CLOCK_SEL 0x04 @@ -168,12 +168,12 @@ struct asic3_platform_data { #define CLOCK_SEL_CX (1 << 2) -#define ASIC3_INTR_Base 0x0B00 +#define ASIC3_INTR_BASE 0x0B00 -#define ASIC3_INTR_IntMask 0x00 /* Interrupt mask control */ -#define ASIC3_INTR_PIntStat 0x04 /* Peripheral interrupt status */ -#define ASIC3_INTR_IntCPS 0x08 /* Interrupt timer clock pre-scale */ -#define ASIC3_INTR_IntTBS 0x0c /* Interrupt timer set */ +#define ASIC3_INTR_INT_MASK 0x00 /* Interrupt mask control */ +#define ASIC3_INTR_P_INT_STAT 0x04 /* Peripheral interrupt status */ +#define ASIC3_INTR_INT_CPS 0x08 /* Interrupt timer clock pre-scale */ +#define ASIC3_INTR_INT_TBS 0x0c /* Interrupt timer set */ #define ASIC3_INTMASK_GINTMASK (1 << 0) /* Global INTs mask 1:enable */ #define ASIC3_INTMASK_GINTEL (1 << 1) /* 1: rising edge, 0: hi level */ |
