diff options
Diffstat (limited to 'include/linux/ieee80211.h')
| -rw-r--r-- | include/linux/ieee80211.h | 212 |
1 files changed, 170 insertions, 42 deletions
diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h index 14126bc..c4e6ca1 100644 --- a/include/linux/ieee80211.h +++ b/include/linux/ieee80211.h @@ -12,8 +12,8 @@ * published by the Free Software Foundation. */ -#ifndef IEEE80211_H -#define IEEE80211_H +#ifndef LINUX_IEEE80211_H +#define LINUX_IEEE80211_H #include <linux/types.h> #include <asm/byteorder.h> @@ -97,7 +97,10 @@ #define IEEE80211_MAX_FRAME_LEN 2352 #define IEEE80211_MAX_SSID_LEN 32 + #define IEEE80211_MAX_MESH_ID_LEN 32 +#define IEEE80211_MESH_CONFIG_LEN 19 + #define IEEE80211_QOS_CTL_LEN 2 #define IEEE80211_QOS_CTL_TID_MASK 0x000F #define IEEE80211_QOS_CTL_TAG1D_MASK 0x0007 @@ -666,6 +669,13 @@ struct ieee80211_cts { u8 ra[6]; } __attribute__ ((packed)); +struct ieee80211_pspoll { + __le16 frame_control; + __le16 aid; + u8 bssid[6]; + u8 ta[6]; +} __attribute__ ((packed)); + /** * struct ieee80211_bar - HT Block Ack Request * @@ -685,28 +695,88 @@ struct ieee80211_bar { #define IEEE80211_BAR_CTRL_ACK_POLICY_NORMAL 0x0000 #define IEEE80211_BAR_CTRL_CBMTID_COMPRESSED_BA 0x0004 + +#define IEEE80211_HT_MCS_MASK_LEN 10 + +/** + * struct ieee80211_mcs_info - MCS information + * @rx_mask: RX mask + * @rx_highest: highest supported RX rate + * @tx_params: TX parameters + */ +struct ieee80211_mcs_info { + u8 rx_mask[IEEE80211_HT_MCS_MASK_LEN]; + __le16 rx_highest; + u8 tx_params; + u8 reserved[3]; +} __attribute__((packed)); + +/* 802.11n HT capability MSC set */ +#define IEEE80211_HT_MCS_RX_HIGHEST_MASK 0x3ff +#define IEEE80211_HT_MCS_TX_DEFINED 0x01 +#define IEEE80211_HT_MCS_TX_RX_DIFF 0x02 +/* value 0 == 1 stream etc */ +#define IEEE80211_HT_MCS_TX_MAX_STREAMS_MASK 0x0C +#define IEEE80211_HT_MCS_TX_MAX_STREAMS_SHIFT 2 +#define IEEE80211_HT_MCS_TX_MAX_STREAMS 4 +#define IEEE80211_HT_MCS_TX_UNEQUAL_MODULATION 0x10 + +/* + * 802.11n D5.0 20.3.5 / 20.6 says: + * - indices 0 to 7 and 32 are single spatial stream + * - 8 to 31 are multiple spatial streams using equal modulation + * [8..15 for two streams, 16..23 for three and 24..31 for four] + * - remainder are multiple spatial streams using unequal modulation + */ +#define IEEE80211_HT_MCS_UNEQUAL_MODULATION_START 33 +#define IEEE80211_HT_MCS_UNEQUAL_MODULATION_START_BYTE \ + (IEEE80211_HT_MCS_UNEQUAL_MODULATION_START / 8) + /** * struct ieee80211_ht_cap - HT capabilities * - * This structure refers to "HT capabilities element" as - * described in 802.11n draft section 7.3.2.52 + * This structure is the "HT capabilities element" as + * described in 802.11n D5.0 7.3.2.57 */ struct ieee80211_ht_cap { __le16 cap_info; u8 ampdu_params_info; - u8 supp_mcs_set[16]; + + /* 16 bytes MCS information */ + struct ieee80211_mcs_info mcs; + __le16 extended_ht_cap_info; __le32 tx_BF_cap_info; u8 antenna_selection_info; } __attribute__ ((packed)); +/* 802.11n HT capabilities masks (for cap_info) */ +#define IEEE80211_HT_CAP_LDPC_CODING 0x0001 +#define IEEE80211_HT_CAP_SUP_WIDTH_20_40 0x0002 +#define IEEE80211_HT_CAP_SM_PS 0x000C +#define IEEE80211_HT_CAP_GRN_FLD 0x0010 +#define IEEE80211_HT_CAP_SGI_20 0x0020 +#define IEEE80211_HT_CAP_SGI_40 0x0040 +#define IEEE80211_HT_CAP_TX_STBC 0x0080 +#define IEEE80211_HT_CAP_RX_STBC 0x0300 +#define IEEE80211_HT_CAP_DELAY_BA 0x0400 +#define IEEE80211_HT_CAP_MAX_AMSDU 0x0800 +#define IEEE80211_HT_CAP_DSSSCCK40 0x1000 +#define IEEE80211_HT_CAP_PSMP_SUPPORT 0x2000 +#define IEEE80211_HT_CAP_40MHZ_INTOLERANT 0x4000 +#define IEEE80211_HT_CAP_LSIG_TXOP_PROT 0x8000 + +/* 802.11n HT capability AMPDU settings (for ampdu_params_info) */ +#define IEEE80211_HT_AMPDU_PARM_FACTOR 0x03 +#define IEEE80211_HT_AMPDU_PARM_DENSITY 0x1C + /** - * struct ieee80211_ht_cap - HT additional information + * struct ieee80211_ht_info - HT information * - * This structure refers to "HT information element" as - * described in 802.11n draft section 7.3.2.53 + * This structure is the "HT information element" as + * described in 802.11n D5.0 7.3.2.58 */ -struct ieee80211_ht_addt_info { +struct ieee80211_ht_info { u8 control_chan; u8 ht_param; __le16 operation_mode; @@ -714,36 +784,33 @@ struct ieee80211_ht_addt_info { u8 basic_set[16]; } __attribute__ ((packed)); -/* 802.11n HT capabilities masks */ -#define IEEE80211_HT_CAP_SUP_WIDTH 0x0002 -#define IEEE80211_HT_CAP_SM_PS 0x000C -#define IEEE80211_HT_CAP_GRN_FLD 0x0010 -#define IEEE80211_HT_CAP_SGI_20 0x0020 -#define IEEE80211_HT_CAP_SGI_40 0x0040 -#define IEEE80211_HT_CAP_DELAY_BA 0x0400 -#define IEEE80211_HT_CAP_MAX_AMSDU 0x0800 -#define IEEE80211_HT_CAP_DSSSCCK40 0x1000 -/* 802.11n HT capability AMPDU settings */ -#define IEEE80211_HT_CAP_AMPDU_FACTOR 0x03 -#define IEEE80211_HT_CAP_AMPDU_DENSITY 0x1C -/* 802.11n HT capability MSC set */ -#define IEEE80211_SUPP_MCS_SET_UEQM 4 -#define IEEE80211_HT_CAP_MAX_STREAMS 4 -#define IEEE80211_SUPP_MCS_SET_LEN 10 -/* maximum streams the spec allows */ -#define IEEE80211_HT_CAP_MCS_TX_DEFINED 0x01 -#define IEEE80211_HT_CAP_MCS_TX_RX_DIFF 0x02 -#define IEEE80211_HT_CAP_MCS_TX_STREAMS 0x0C -#define IEEE80211_HT_CAP_MCS_TX_UEQM 0x10 -/* 802.11n HT IE masks */ -#define IEEE80211_HT_IE_CHA_SEC_OFFSET 0x03 -#define IEEE80211_HT_IE_CHA_SEC_NONE 0x00 -#define IEEE80211_HT_IE_CHA_SEC_ABOVE 0x01 -#define IEEE80211_HT_IE_CHA_SEC_BELOW 0x03 -#define IEEE80211_HT_IE_CHA_WIDTH 0x04 -#define IEEE80211_HT_IE_HT_PROTECTION 0x0003 -#define IEEE80211_HT_IE_NON_GF_STA_PRSNT 0x0004 -#define IEEE80211_HT_IE_NON_HT_STA_PRSNT 0x0010 +/* for ht_param */ +#define IEEE80211_HT_PARAM_CHA_SEC_OFFSET 0x03 +#define IEEE80211_HT_PARAM_CHA_SEC_NONE 0x00 +#define IEEE80211_HT_PARAM_CHA_SEC_ABOVE 0x01 +#define IEEE80211_HT_PARAM_CHA_SEC_BELOW 0x03 +#define IEEE80211_HT_PARAM_CHAN_WIDTH_ANY 0x04 +#define IEEE80211_HT_PARAM_RIFS_MODE 0x08 +#define IEEE80211_HT_PARAM_SPSMP_SUPPORT 0x10 +#define IEEE80211_HT_PARAM_SERV_INTERVAL_GRAN 0xE0 + +/* for operation_mode */ +#define IEEE80211_HT_OP_MODE_PROTECTION 0x0003 +#define IEEE80211_HT_OP_MODE_PROTECTION_NONE 0 +#define IEEE80211_HT_OP_MODE_PROTECTION_NONMEMBER 1 +#define IEEE80211_HT_OP_MODE_PROTECTION_20MHZ 2 +#define IEEE80211_HT_OP_MODE_PROTECTION_NONHT_MIXED 3 +#define IEEE80211_HT_OP_MODE_NON_GF_STA_PRSNT 0x0004 +#define IEEE80211_HT_OP_MODE_NON_HT_STA_PRSNT 0x0010 + +/* for stbc_param */ +#define IEEE80211_HT_STBC_PARAM_DUAL_BEACON 0x0040 +#define IEEE80211_HT_STBC_PARAM_DUAL_CTS_PROT 0x0080 +#define IEEE80211_HT_STBC_PARAM_STBC_BEACON 0x0100 +#define IEEE80211_HT_STBC_PARAM_LSIG_TXOP_FULLPROT 0x0200 +#define IEEE80211_HT_STBC_PARAM_PCO_ACTIVE 0x0400 +#define IEEE80211_HT_STBC_PARAM_PCO_PHASE 0x0800 + /* block-ack parameters */ #define IEEE80211_ADDBA_PARAM_POLICY_MASK 0x0002 @@ -769,7 +836,6 @@ struct ieee80211_ht_addt_info { /* Authentication algorithms */ #define WLAN_AUTH_OPEN 0 #define WLAN_AUTH_SHARED_KEY 1 -#define WLAN_AUTH_FAST_BSS_TRANSITION 2 #define WLAN_AUTH_LEAP 128 #define WLAN_AUTH_CHALLENGE_LEN 128 @@ -949,7 +1015,7 @@ enum ieee80211_eid { WLAN_EID_EXT_SUPP_RATES = 50, /* 802.11n */ WLAN_EID_HT_CAPABILITY = 45, - WLAN_EID_HT_EXTRA_INFO = 61, + WLAN_EID_HT_INFORMATION = 61, /* 802.11i */ WLAN_EID_RSN = 48, WLAN_EID_WPA = 221, @@ -976,6 +1042,68 @@ enum ieee80211_spectrum_mgmt_actioncode { WLAN_ACTION_SPCT_CHL_SWITCH = 4, }; +/* + * IEEE 802.11-2007 7.3.2.9 Country information element + * + * Minimum length is 8 octets, ie len must be evenly + * divisible by 2 + */ + +/* Although the spec says 8 I'm seeing 6 in practice */ +#define IEEE80211_COUNTRY_IE_MIN_LEN 6 + +/* + * For regulatory extension stuff see IEEE 802.11-2007 + * Annex I (page 1141) and Annex J (page 1147). Also + * review 7.3.2.9. + * + * When dot11RegulatoryClassesRequired is true and the + * first_channel/reg_extension_id is >= 201 then the IE + * compromises of the 'ext' struct represented below: + * + * - Regulatory extension ID - when generating IE this just needs + * to be monotonically increasing for each triplet passed in + * the IE + * - Regulatory class - index into set of rules + * - Coverage class - index into air propagation time (Table 7-27), + * in microseconds, you can compute the air propagation time from + * the index by multiplying by 3, so index 10 yields a propagation + * of 10 us. Valid values are 0-31, values 32-255 are not defined + * yet. A value of 0 inicates air propagation of <= 1 us. + * + * See also Table I.2 for Emission limit sets and table + * I.3 for Behavior limit sets. Table J.1 indicates how to map + * a reg_class to an emission limit set and behavior limit set. + */ +#define IEEE80211_COUNTRY_EXTENSION_ID 201 + +/* + * Channels numbers in the IE must be monotonically increasing + * if dot11RegulatoryClassesRequired is not true. + * + * If dot11RegulatoryClassesRequired is true consecutive + * subband triplets following a regulatory triplet shall + * have monotonically increasing first_channel number fields. + * + * Channel numbers shall not overlap. + * + * Note that max_power is signed. + */ +struct ieee80211_country_ie_triplet { + union { + struct { + u8 first_channel; + u8 num_channels; + s8 max_power; + } __attribute__ ((packed)) chans; + struct { + u8 reg_extension_id; + u8 reg_class; + u8 coverage_class; + } __attribute__ ((packed)) ext; + }; +} __attribute__ ((packed)); + /* BACK action code */ enum ieee80211_back_actioncode { WLAN_ACTION_ADDBA_REQ = 0, @@ -1057,4 +1185,4 @@ static inline u8 *ieee80211_get_DA(struct ieee80211_hdr *hdr) return hdr->addr1; } -#endif /* IEEE80211_H */ +#endif /* LINUX_IEEE80211_H */ |
