summaryrefslogtreecommitdiffstats
path: root/include/linux/ethtool.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/linux/ethtool.h')
-rw-r--r--include/linux/ethtool.h135
1 files changed, 64 insertions, 71 deletions
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index c6e427a..be32dd0 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -117,99 +117,92 @@ struct ethtool_eeprom {
__u8 data[0];
};
-/* for configuring coalescing parameters of chip */
+/**
+ * struct ethtool_coalesce - coalescing parameters of chip
+ * @cmd: ETHTOOL_{G,S}COALESCE
+ * @rx_coalesce_usecs: How many usecs to delay an RX interrupt after
+ * a packet arrives. If 0, only @rx_max_coalesced_frames is used.
+ * @rx_max_coalesced_frames: How many packets to delay an RX interrupt
+ * after a packet arrives. If 0, only @rx_coalesce_usecs is used.
+ * @rx_coalesce_usecs_irq: Same as @rx_coalesce_usecs, except that
+ * this value applies while an IRQ is being serviced by the host.
+ * @rx_max_coalesced_frames_irq: Same as @rx_max_coalesced_frames,
+ * except that this value applies while an IRQ is being serviced
+ * by the host.
+ * @tx_coalesce_usecs: How many usecs to delay a TX interrupt after
+ * a packet is sent. If 0, only @tx_max_coalesced_frames
+ * is used.
+ * @tx_max_coalesced_frames: How many packets to delay a TX interrupt
+ * after a packet is sent. If 0, only @tx_coalesce_usecs is
+ * used.
+ * @tx_coalesce_usecs_irq: Same as @tx_coalesce_usecs, except that
+ * this value applies while an IRQ is being serviced by the host.
+ * @tx_max_coalesced_frames_irq: Same as @tx_max_coalesced_frames,
+ * except that this value applies while an IRQ is being serviced
+ * by the host.
+ * @stats_block_coalesce_usecs: How many usecs to delay in-memory
+ * statistics block updates. Some drivers do not have an
+ * in-memory statistic block, and in such cases this value is
+ * ignored. This value must not be zero.
+ * @use_adaptive_rx_coalesce: Enable adaptive RX coalescing.
+ * @use_adaptive_tx_coalesce: Enable adaptive TX coalescing.
+ * @pkt_rate_low: Threshold for low packet rate (packets per second).
+ * @rx_coalesce_usecs_low: How many usecs to delay an RX interrupt after
+ * a packet arrives, when the packet rate is below @pkt_rate_low.
+ * @rx_max_coalesced_frames_low: How many packets to delay an RX interrupt
+ * after a packet arrives, when the packet rate is below @pkt_rate_low.
+ * @tx_coalesce_usecs_low: How many usecs to delay a TX interrupt after
+ * a packet is sent, when the packet rate is below @pkt_rate_low.
+ * @tx_max_coalesced_frames_low: How many packets to delay a TX interrupt
+ * after a packet is sent, when the packet rate is below @pkt_rate_low.
+ * @pkt_rate_high: Threshold for high packet rate (packets per second).
+ * @rx_coalesce_usecs_high: How many usecs to delay an RX interrupt after
+ * a packet arrives, when the packet rate is above @pkt_rate_high.
+ * @rx_max_coalesced_frames_high: How many packets to delay an RX interrupt
+ * after a packet arrives, when the packet rate is above @pkt_rate_high.
+ * @tx_coalesce_usecs_high: How many usecs to delay a TX interrupt after
+ * a packet is sent, when the packet rate is above @pkt_rate_high.
+ * @tx_max_coalesced_frames_high: How many packets to delay a TX interrupt
+ * after a packet is sent, when the packet rate is above @pkt_rate_high.
+ * @rate_sample_interval: How often to do adaptive coalescing packet rate
+ * sampling, measured in seconds. Must not be zero.
+ *
+ * It is illegal to set both usecs and max frames to zero as this
+ * would cause interrupts to never be generated.
+ *
+ * Adaptive RX/TX coalescing is an algorithm implemented by some
+ * drivers to improve latency under low packet rates and improve
+ * throughput under high packet rates. Some drivers only implement
+ * one of RX or TX adaptive coalescing. Anything not implemented by
+ * the driver causes these values to be silently ignored.
+ *
+ * When the packet rate is below @pkt_rate_high but above
+ * @pkt_rate_low (both measured in packets per second) the
+ * normal {rx,tx}_* coalescing parameters are used.
+ */
struct ethtool_coalesce {
- __u32 cmd; /* ETHTOOL_{G,S}COALESCE */
-
- /* How many usecs to delay an RX interrupt after
- * a packet arrives. If 0, only rx_max_coalesced_frames
- * is used.
- */
+ __u32 cmd;
__u32 rx_coalesce_usecs;
-
- /* How many packets to delay an RX interrupt after
- * a packet arrives. If 0, only rx_coalesce_usecs is
- * used. It is illegal to set both usecs and max frames
- * to zero as this would cause RX interrupts to never be
- * generated.
- */
__u32 rx_max_coalesced_frames;
-
- /* Same as above two parameters, except that these values
- * apply while an IRQ is being serviced by the host. Not
- * all cards support this feature and the values are ignored
- * in that case.
- */
__u32 rx_coalesce_usecs_irq;
__u32 rx_max_coalesced_frames_irq;
-
- /* How many usecs to delay a TX interrupt after
- * a packet is sent. If 0, only tx_max_coalesced_frames
- * is used.
- */
__u32 tx_coalesce_usecs;
-
- /* How many packets to delay a TX interrupt after
- * a packet is sent. If 0, only tx_coalesce_usecs is
- * used. It is illegal to set both usecs and max frames
- * to zero as this would cause TX interrupts to never be
- * generated.
- */
__u32 tx_max_coalesced_frames;
-
- /* Same as above two parameters, except that these values
- * apply while an IRQ is being serviced by the host. Not
- * all cards support this feature and the values are ignored
- * in that case.
- */
__u32 tx_coalesce_usecs_irq;
__u32 tx_max_coalesced_frames_irq;
-
- /* How many usecs to delay in-memory statistics
- * block updates. Some drivers do not have an in-memory
- * statistic block, and in such cases this value is ignored.
- * This value must not be zero.
- */
__u32 stats_block_coalesce_usecs;
-
- /* Adaptive RX/TX coalescing is an algorithm implemented by
- * some drivers to improve latency under low packet rates and
- * improve throughput under high packet rates. Some drivers
- * only implement one of RX or TX adaptive coalescing. Anything
- * not implemented by the driver causes these values to be
- * silently ignored.
- */
__u32 use_adaptive_rx_coalesce;
__u32 use_adaptive_tx_coalesce;
-
- /* When the packet rate (measured in packets per second)
- * is below pkt_rate_low, the {rx,tx}_*_low parameters are
- * used.
- */
__u32 pkt_rate_low;
__u32 rx_coalesce_usecs_low;
__u32 rx_max_coalesced_frames_low;
__u32 tx_coalesce_usecs_low;
__u32 tx_max_coalesced_frames_low;
-
- /* When the packet rate is below pkt_rate_high but above
- * pkt_rate_low (both measured in packets per second) the
- * normal {rx,tx}_* coalescing parameters are used.
- */
-
- /* When the packet rate is (measured in packets per second)
- * is above pkt_rate_high, the {rx,tx}_*_high parameters are
- * used.
- */
__u32 pkt_rate_high;
__u32 rx_coalesce_usecs_high;
__u32 rx_max_coalesced_frames_high;
__u32 tx_coalesce_usecs_high;
__u32 tx_max_coalesced_frames_high;
-
- /* How often to do adaptive coalescing packet rate sampling,
- * measured in seconds. Must not be zero.
- */
__u32 rate_sample_interval;
};
OpenPOWER on IntegriCloud