diff options
Diffstat (limited to 'include/asm-xtensa/xtensa/xt2000.h')
| -rw-r--r-- | include/asm-xtensa/xtensa/xt2000.h | 408 |
1 files changed, 408 insertions, 0 deletions
diff --git a/include/asm-xtensa/xtensa/xt2000.h b/include/asm-xtensa/xtensa/xt2000.h new file mode 100644 index 0000000..703a450 --- /dev/null +++ b/include/asm-xtensa/xtensa/xt2000.h @@ -0,0 +1,408 @@ +#ifndef _INC_XT2000_H_ +#define _INC_XT2000_H_ + +/* + * THIS FILE IS GENERATED -- DO NOT MODIFY BY HAND + * + * include/asm-xtensa/xtensa/xt2000.h - Definitions specific to the + * Tensilica XT2000 Emulation Board + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 2002 Tensilica Inc. + */ + + +#include <xtensa/config/core.h> +#include <xtensa/config/system.h> + + +/* + * Default assignment of XT2000 devices to external interrupts. + */ + +/* Ethernet interrupt: */ +#ifdef XCHAL_EXTINT3_NUM +#define SONIC83934_INTNUM XCHAL_EXTINT3_NUM +#define SONIC83934_INTLEVEL XCHAL_EXTINT3_LEVEL +#define SONIC83934_INTMASK XCHAL_EXTINT3_MASK +#else +#define SONIC83934_INTMASK 0 +#endif + +/* DUART channel 1 interrupt (P1 - console): */ +#ifdef XCHAL_EXTINT4_NUM +#define DUART16552_1_INTNUM XCHAL_EXTINT4_NUM +#define DUART16552_1_INTLEVEL XCHAL_EXTINT4_LEVEL +#define DUART16552_1_INTMASK XCHAL_EXTINT4_MASK +#else +#define DUART16552_1_INTMASK 0 +#endif + +/* DUART channel 2 interrupt (P2 - 2nd serial port): */ +#ifdef XCHAL_EXTINT5_NUM +#define DUART16552_2_INTNUM XCHAL_EXTINT5_NUM +#define DUART16552_2_INTLEVEL XCHAL_EXTINT5_LEVEL +#define DUART16552_2_INTMASK XCHAL_EXTINT5_MASK +#else +#define DUART16552_2_INTMASK 0 +#endif + +/* FPGA-combined PCI/etc interrupts: */ +#ifdef XCHAL_EXTINT6_NUM +#define XT2000_FPGAPCI_INTNUM XCHAL_EXTINT6_NUM +#define XT2000_FPGAPCI_INTLEVEL XCHAL_EXTINT6_LEVEL +#define XT2000_FPGAPCI_INTMASK XCHAL_EXTINT6_MASK +#else +#define XT2000_FPGAPCI_INTMASK 0 +#endif + + + +/* + * Device addresses. + * + * Note: for endianness-independence, use 32-bit loads and stores for all + * register accesses to Ethernet, DUART and LED devices. Undefined bits + * may need to be masked out if needed when reading if the actual register + * size is smaller than 32 bits. + * + * Note: XT2000 bus byte lanes are defined in terms of msbyte and lsbyte + * relative to the processor. So 32-bit registers are accessed consistently + * from both big and little endian processors. However, this means byte + * sequences are not consistent between big and little endian processors. + * This is fine for RAM, and for ROM if ROM is created for a specific + * processor (and thus has correct byte sequences). However this may be + * unexpected for Flash, which might contain a file-system that one wants + * to use for multiple processor configurations (eg. the Flash might contain + * the Ethernet card's address, endianness-independent application data, etc). + * That is, byte sequences written in Flash by a core of a given endianness + * will be byte-swapped when seen by a core of the other endianness. + * Someone implementing an endianness-independent Flash file system will + * likely handle this byte-swapping issue in the Flash driver software. + */ + +#define DUART16552_XTAL_FREQ 18432000 /* crystal frequency in Hz */ +#define XTBOARD_FLASH_MAXSIZE 0x4000000 /* 64 MB (max; depends on what is socketed!) */ +#define XTBOARD_EPROM_MAXSIZE 0x0400000 /* 4 MB (max; depends on what is socketed!) */ +#define XTBOARD_EEPROM_MAXSIZE 0x0080000 /* 512 kB (max; depends on what is socketed!) */ +#define XTBOARD_ASRAM_SIZE 0x0100000 /* 1 MB */ +#define XTBOARD_PCI_MEM_SIZE 0x8000000 /* 128 MB (allocated) */ +#define XTBOARD_PCI_IO_SIZE 0x1000000 /* 16 MB (allocated) */ + +#ifdef XSHAL_IOBLOCK_BYPASS_PADDR +/* PCI memory space: */ +# define XTBOARD_PCI_MEM_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0x0000000) +/* Socketed Flash (eg. 2 x 16-bit devices): */ +# define XTBOARD_FLASH_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0x8000000) +/* PCI I/O space: */ +# define XTBOARD_PCI_IO_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xC000000) +/* V3 PCI interface chip register/config space: */ +# define XTBOARD_V3PCI_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD000000) +/* Bus Interface registers: */ +# define XTBOARD_BUSINT_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD010000) +/* FPGA registers: */ +# define XT2000_FPGAREGS_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD020000) +/* SONIC SN83934 Ethernet controller/transceiver: */ +# define SONIC83934_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD030000) +/* 8-character bitmapped LED display: */ +# define XTBOARD_LED_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD040000) +/* National-Semi PC16552D DUART: */ +# define DUART16552_1_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD050020) /* channel 1 (P1 - console) */ +# define DUART16552_2_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD050000) /* channel 2 (P2) */ +/* Asynchronous Static RAM: */ +# define XTBOARD_ASRAM_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD400000) +/* 8-bit EEPROM: */ +# define XTBOARD_EEPROM_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD600000) +/* 2 x 16-bit EPROMs: */ +# define XTBOARD_EPROM_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0xD800000) +#endif /* XSHAL_IOBLOCK_BYPASS_PADDR */ + +/* These devices might be accessed cached: */ +#ifdef XSHAL_IOBLOCK_CACHED_PADDR +# define XTBOARD_PCI_MEM_CACHED_PADDR (XSHAL_IOBLOCK_CACHED_PADDR+0x0000000) +# define XTBOARD_FLASH_CACHED_PADDR (XSHAL_IOBLOCK_CACHED_PADDR+0x8000000) +# define XTBOARD_ASRAM_CACHED_PADDR (XSHAL_IOBLOCK_CACHED_PADDR+0xD400000) +# define XTBOARD_EEPROM_CACHED_PADDR (XSHAL_IOBLOCK_CACHED_PADDR+0xD600000) +# define XTBOARD_EPROM_CACHED_PADDR (XSHAL_IOBLOCK_CACHED_PADDR+0xD800000) +#endif /* XSHAL_IOBLOCK_CACHED_PADDR */ + + +/*** Same thing over again, this time with virtual addresses: ***/ + +#ifdef XSHAL_IOBLOCK_BYPASS_VADDR +/* PCI memory space: */ +# define XTBOARD_PCI_MEM_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0x0000000) +/* Socketed Flash (eg. 2 x 16-bit devices): */ +# define XTBOARD_FLASH_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0x8000000) +/* PCI I/O space: */ +# define XTBOARD_PCI_IO_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xC000000) +/* V3 PCI interface chip register/config space: */ +# define XTBOARD_V3PCI_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD000000) +/* Bus Interface registers: */ +# define XTBOARD_BUSINT_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD010000) +/* FPGA registers: */ +# define XT2000_FPGAREGS_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD020000) +/* SONIC SN83934 Ethernet controller/transceiver: */ +# define SONIC83934_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD030000) +/* 8-character bitmapped LED display: */ +# define XTBOARD_LED_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD040000) +/* National-Semi PC16552D DUART: */ +# define DUART16552_1_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD050020) /* channel 1 (P1 - console) */ +# define DUART16552_2_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD050000) /* channel 2 (P2) */ +/* Asynchronous Static RAM: */ +# define XTBOARD_ASRAM_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD400000) +/* 8-bit EEPROM: */ +# define XTBOARD_EEPROM_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD600000) +/* 2 x 16-bit EPROMs: */ +# define XTBOARD_EPROM_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0xD800000) +#endif /* XSHAL_IOBLOCK_BYPASS_VADDR */ + +/* These devices might be accessed cached: */ +#ifdef XSHAL_IOBLOCK_CACHED_VADDR +# define XTBOARD_PCI_MEM_CACHED_VADDR (XSHAL_IOBLOCK_CACHED_VADDR+0x0000000) +# define XTBOARD_FLASH_CACHED_VADDR (XSHAL_IOBLOCK_CACHED_VADDR+0x8000000) +# define XTBOARD_ASRAM_CACHED_VADDR (XSHAL_IOBLOCK_CACHED_VADDR+0xD400000) +# define XTBOARD_EEPROM_CACHED_VADDR (XSHAL_IOBLOCK_CACHED_VADDR+0xD600000) +# define XTBOARD_EPROM_CACHED_VADDR (XSHAL_IOBLOCK_CACHED_VADDR+0xD800000) +#endif /* XSHAL_IOBLOCK_CACHED_VADDR */ + + +/* System ROM: */ +#define XTBOARD_ROM_SIZE XSHAL_ROM_SIZE +#ifdef XSHAL_ROM_VADDR +#define XTBOARD_ROM_VADDR XSHAL_ROM_VADDR +#endif +#ifdef XSHAL_ROM_PADDR +#define XTBOARD_ROM_PADDR XSHAL_ROM_PADDR +#endif + +/* System RAM: */ +#define XTBOARD_RAM_SIZE XSHAL_RAM_SIZE +#ifdef XSHAL_RAM_VADDR +#define XTBOARD_RAM_VADDR XSHAL_RAM_VADDR +#endif +#ifdef XSHAL_RAM_PADDR +#define XTBOARD_RAM_PADDR XSHAL_RAM_PADDR +#endif +#define XTBOARD_RAM_BYPASS_VADDR XSHAL_RAM_BYPASS_VADDR +#define XTBOARD_RAM_BYPASS_PADDR XSHAL_RAM_BYPASS_PADDR + + + +/* + * Things that depend on device addresses. + */ + + +#define XTBOARD_CACHEATTR_WRITEBACK XSHAL_XT2000_CACHEATTR_WRITEBACK +#define XTBOARD_CACHEATTR_WRITEALLOC XSHAL_XT2000_CACHEATTR_WRITEALLOC +#define XTBOARD_CACHEATTR_WRITETHRU XSHAL_XT2000_CACHEATTR_WRITETHRU +#define XTBOARD_CACHEATTR_BYPASS XSHAL_XT2000_CACHEATTR_BYPASS +#define XTBOARD_CACHEATTR_DEFAULT XSHAL_XT2000_CACHEATTR_DEFAULT + +#define XTBOARD_BUSINT_PIPE_REGIONS XSHAL_XT2000_PIPE_REGIONS +#define XTBOARD_BUSINT_SDRAM_REGIONS XSHAL_XT2000_SDRAM_REGIONS + + + +/* + * BusLogic (FPGA) registers. + * All these registers are normally accessed using 32-bit loads/stores. + */ + +/* Register offsets: */ +#define XT2000_DATECD_OFS 0x00 /* date code (read-only) */ +#define XT2000_STSREG_OFS 0x04 /* status (read-only) */ +#define XT2000_SYSLED_OFS 0x08 /* system LED */ +#define XT2000_WRPROT_OFS 0x0C /* write protect */ +#define XT2000_SWRST_OFS 0x10 /* software reset */ +#define XT2000_SYSRST_OFS 0x14 /* system (peripherals) reset */ +#define XT2000_IMASK_OFS 0x18 /* interrupt mask */ +#define XT2000_ISTAT_OFS 0x1C /* interrupt status */ +#define XT2000_V3CFG_OFS 0x20 /* V3 config (V320 PCI) */ + +/* Physical register addresses: */ +#ifdef XT2000_FPGAREGS_PADDR +#define XT2000_DATECD_PADDR (XT2000_FPGAREGS_PADDR+XT2000_DATECD_OFS) +#define XT2000_STSREG_PADDR (XT2000_FPGAREGS_PADDR+XT2000_STSREG_OFS) +#define XT2000_SYSLED_PADDR (XT2000_FPGAREGS_PADDR+XT2000_SYSLED_OFS) +#define XT2000_WRPROT_PADDR (XT2000_FPGAREGS_PADDR+XT2000_WRPROT_OFS) +#define XT2000_SWRST_PADDR (XT2000_FPGAREGS_PADDR+XT2000_SWRST_OFS) +#define XT2000_SYSRST_PADDR (XT2000_FPGAREGS_PADDR+XT2000_SYSRST_OFS) +#define XT2000_IMASK_PADDR (XT2000_FPGAREGS_PADDR+XT2000_IMASK_OFS) +#define XT2000_ISTAT_PADDR (XT2000_FPGAREGS_PADDR+XT2000_ISTAT_OFS) +#define XT2000_V3CFG_PADDR (XT2000_FPGAREGS_PADDR+XT2000_V3CFG_OFS) +#endif + +/* Virtual register addresses: */ +#ifdef XT2000_FPGAREGS_VADDR +#define XT2000_DATECD_VADDR (XT2000_FPGAREGS_VADDR+XT2000_DATECD_OFS) +#define XT2000_STSREG_VADDR (XT2000_FPGAREGS_VADDR+XT2000_STSREG_OFS) +#define XT2000_SYSLED_VADDR (XT2000_FPGAREGS_VADDR+XT2000_SYSLED_OFS) +#define XT2000_WRPROT_VADDR (XT2000_FPGAREGS_VADDR+XT2000_WRPROT_OFS) +#define XT2000_SWRST_VADDR (XT2000_FPGAREGS_VADDR+XT2000_SWRST_OFS) +#define XT2000_SYSRST_VADDR (XT2000_FPGAREGS_VADDR+XT2000_SYSRST_OFS) +#define XT2000_IMASK_VADDR (XT2000_FPGAREGS_VADDR+XT2000_IMASK_OFS) +#define XT2000_ISTAT_VADDR (XT2000_FPGAREGS_VADDR+XT2000_ISTAT_OFS) +#define XT2000_V3CFG_VADDR (XT2000_FPGAREGS_VADDR+XT2000_V3CFG_OFS) +/* Register access (for C code): */ +#define XT2000_DATECD_REG (*(volatile unsigned*) XT2000_DATECD_VADDR) +#define XT2000_STSREG_REG (*(volatile unsigned*) XT2000_STSREG_VADDR) +#define XT2000_SYSLED_REG (*(volatile unsigned*) XT2000_SYSLED_VADDR) +#define XT2000_WRPROT_REG (*(volatile unsigned*) XT2000_WRPROT_VADDR) +#define XT2000_SWRST_REG (*(volatile unsigned*) XT2000_SWRST_VADDR) +#define XT2000_SYSRST_REG (*(volatile unsigned*) XT2000_SYSRST_VADDR) +#define XT2000_IMASK_REG (*(volatile unsigned*) XT2000_IMASK_VADDR) +#define XT2000_ISTAT_REG (*(volatile unsigned*) XT2000_ISTAT_VADDR) +#define XT2000_V3CFG_REG (*(volatile unsigned*) XT2000_V3CFG_VADDR) +#endif + +/* DATECD (date code) bit fields: */ + +/* BCD-coded month (01..12): */ +#define XT2000_DATECD_MONTH_SHIFT 24 +#define XT2000_DATECD_MONTH_BITS 8 +#define XT2000_DATECD_MONTH_MASK 0xFF000000 +/* BCD-coded day (01..31): */ +#define XT2000_DATECD_DAY_SHIFT 16 +#define XT2000_DATECD_DAY_BITS 8 +#define XT2000_DATECD_DAY_MASK 0x00FF0000 +/* BCD-coded year (2001..9999): */ +#define XT2000_DATECD_YEAR_SHIFT 0 +#define XT2000_DATECD_YEAR_BITS 16 +#define XT2000_DATECD_YEAR_MASK 0x0000FFFF + +/* STSREG (status) bit fields: */ + +/* Switch SW3 setting bit fields (0=off/up, 1=on/down): */ +#define XT2000_STSREG_SW3_SHIFT 0 +#define XT2000_STSREG_SW3_BITS 4 +#define XT2000_STSREG_SW3_MASK 0x0000000F +/* Boot-select bits of switch SW3: */ +#define XT2000_STSREG_BOOTSEL_SHIFT 0 +#define XT2000_STSREG_BOOTSEL_BITS 2 +#define XT2000_STSREG_BOOTSEL_MASK 0x00000003 +/* Boot-select values: */ +#define XT2000_STSREG_BOOTSEL_FLASH 0 +#define XT2000_STSREG_BOOTSEL_EPROM16 1 +#define XT2000_STSREG_BOOTSEL_PROM8 2 +#define XT2000_STSREG_BOOTSEL_ASRAM 3 +/* User-defined bits of switch SW3: */ +#define XT2000_STSREG_SW3_2_SHIFT 2 +#define XT2000_STSREG_SW3_2_MASK 0x00000004 +#define XT2000_STSREG_SW3_3_SHIFT 3 +#define XT2000_STSREG_SW3_3_MASK 0x00000008 + +/* SYSLED (system LED) bit fields: */ + +/* LED control bit (0=off, 1=on): */ +#define XT2000_SYSLED_LEDON_SHIFT 0 +#define XT2000_SYSLED_LEDON_MASK 0x00000001 + +/* WRPROT (write protect) bit fields (0=writable, 1=write-protected [default]): */ + +/* Flash write protect: */ +#define XT2000_WRPROT_FLWP_SHIFT 0 +#define XT2000_WRPROT_FLWP_MASK 0x00000001 +/* Reserved but present write protect bits: */ +#define XT2000_WRPROT_WRP_SHIFT 1 +#define XT2000_WRPROT_WRP_BITS 7 +#define XT2000_WRPROT_WRP_MASK 0x000000FE + +/* SWRST (software reset; allows s/w to generate power-on equivalent reset): */ + +/* Software reset bits: */ +#define XT2000_SWRST_SWR_SHIFT 0 +#define XT2000_SWRST_SWR_BITS 16 +#define XT2000_SWRST_SWR_MASK 0x0000FFFF +/* Software reset value -- writing this value resets the board: */ +#define XT2000_SWRST_RESETVALUE 0x0000DEAD + +/* SYSRST (system reset; controls reset of individual peripherals): */ + +/* All-device reset: */ +#define XT2000_SYSRST_ALL_SHIFT 0 +#define XT2000_SYSRST_ALL_BITS 4 +#define XT2000_SYSRST_ALL_MASK 0x0000000F +/* HDSP-2534 LED display reset (1=reset, 0=nothing): */ +#define XT2000_SYSRST_LED_SHIFT 0 +#define XT2000_SYSRST_LED_MASK 0x00000001 +/* Sonic DP83934 Ethernet controller reset (1=reset, 0=nothing): */ +#define XT2000_SYSRST_SONIC_SHIFT 1 +#define XT2000_SYSRST_SONIC_MASK 0x00000002 +/* DP16552 DUART reset (1=reset, 0=nothing): */ +#define XT2000_SYSRST_DUART_SHIFT 2 +#define XT2000_SYSRST_DUART_MASK 0x00000004 +/* V3 V320 PCI bridge controller reset (1=reset, 0=nothing): */ +#define XT2000_SYSRST_V3_SHIFT 3 +#define XT2000_SYSRST_V3_MASK 0x00000008 + +/* IMASK (interrupt mask; 0=disable, 1=enable): */ +/* ISTAT (interrupt status; 0=inactive, 1=pending): */ + +/* PCI INTP interrupt: */ +#define XT2000_INTMUX_PCI_INTP_SHIFT 2 +#define XT2000_INTMUX_PCI_INTP_MASK 0x00000004 +/* PCI INTS interrupt: */ +#define XT2000_INTMUX_PCI_INTS_SHIFT 3 +#define XT2000_INTMUX_PCI_INTS_MASK 0x00000008 +/* PCI INTD interrupt: */ +#define XT2000_INTMUX_PCI_INTD_SHIFT 4 +#define XT2000_INTMUX_PCI_INTD_MASK 0x00000010 +/* V320 PCI controller interrupt: */ +#define XT2000_INTMUX_V3_SHIFT 5 +#define XT2000_INTMUX_V3_MASK 0x00000020 +/* PCI ENUM interrupt: */ +#define XT2000_INTMUX_PCI_ENUM_SHIFT 6 +#define XT2000_INTMUX_PCI_ENUM_MASK 0x00000040 +/* PCI DEG interrupt: */ +#define XT2000_INTMUX_PCI_DEG_SHIFT 7 +#define XT2000_INTMUX_PCI_DEG_MASK 0x00000080 + +/* V3CFG (V3 config, V320 PCI controller): */ + +/* V3 address control (0=pass-thru, 1=V3 address bits 31:28 set to 4'b0001 [default]): */ +#define XT2000_V3CFG_V3ADC_SHIFT 0 +#define XT2000_V3CFG_V3ADC_MASK 0x00000001 + +/* I2C Devices */ + +#define XT2000_I2C_RTC_ID 0x68 +#define XT2000_I2C_NVRAM0_ID 0x56 /* 1st 256 byte block */ +#define XT2000_I2C_NVRAM1_ID 0x57 /* 2nd 256 byte block */ + +/* NVRAM Board Info structure: */ + +#define XT2000_NVRAM_SIZE 512 + +#define XT2000_NVRAM_BINFO_START 0x100 +#define XT2000_NVRAM_BINFO_SIZE 0x20 +#define XT2000_NVRAM_BINFO_VERSION 0x10 /* version 1.0 */ +#if 0 +#define XT2000_NVRAM_BINFO_VERSION_OFFSET 0x00 +#define XT2000_NVRAM_BINFO_VERSION_SIZE 0x1 +#define XT2000_NVRAM_BINFO_ETH_ADDR_OFFSET 0x02 +#define XT2000_NVRAM_BINFO_ETH_ADDR_SIZE 0x6 +#define XT2000_NVRAM_BINFO_SN_OFFSET 0x10 +#define XT2000_NVRAM_BINFO_SN_SIZE 0xE +#define XT2000_NVRAM_BINFO_CRC_OFFSET 0x1E +#define XT2000_NVRAM_BINFO_CRC_SIZE 0x2 +#endif /*0*/ + +#if !defined(__ASSEMBLY__) && !defined(_NOCLANGUAGE) +typedef struct xt2000_nvram_binfo { + unsigned char version; + unsigned char reserved1; + unsigned char eth_addr[6]; + unsigned char reserved8[8]; + unsigned char serialno[14]; + unsigned char crc[2]; /* 16-bit CRC */ +} xt2000_nvram_binfo; +#endif /*!__ASSEMBLY__ && !_NOCLANGUAGE*/ + + +#endif /*_INC_XT2000_H_*/ + |
