diff options
Diffstat (limited to 'include/asm-sh/sh7760fb.h')
-rw-r--r-- | include/asm-sh/sh7760fb.h | 197 |
1 files changed, 0 insertions, 197 deletions
diff --git a/include/asm-sh/sh7760fb.h b/include/asm-sh/sh7760fb.h deleted file mode 100644 index 8767f61..0000000 --- a/include/asm-sh/sh7760fb.h +++ /dev/null @@ -1,197 +0,0 @@ -/* - * sh7760fb.h -- platform data for SH7760/SH7763 LCDC framebuffer driver. - * - * (c) 2006-2008 MSC Vertriebsges.m.b.H., - * Manuel Lauss <mano@roarinelk.homelinux.net> - * (c) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> - */ - -#ifndef _ASM_SH_SH7760FB_H -#define _ASM_SH_SH7760FB_H - -/* - * some bits of the colormap registers should be written as zero. - * create a mask for that. - */ -#define SH7760FB_PALETTE_MASK 0x00f8fcf8 - -/* The LCDC dma engine always sets bits 27-26 to 1: this is Area3 */ -#define SH7760FB_DMA_MASK 0x0C000000 - -/* palette */ -#define LDPR(x) (((x) << 2)) - -/* framebuffer registers and bits */ -#define LDICKR 0x400 -#define LDMTR 0x402 -/* see sh7760fb.h for LDMTR bits */ -#define LDDFR 0x404 -#define LDDFR_PABD (1 << 8) -#define LDDFR_COLOR_MASK 0x7F -#define LDSMR 0x406 -#define LDSMR_ROT (1 << 13) -#define LDSARU 0x408 -#define LDSARL 0x40c -#define LDLAOR 0x410 -#define LDPALCR 0x412 -#define LDPALCR_PALS (1 << 4) -#define LDPALCR_PALEN (1 << 0) -#define LDHCNR 0x414 -#define LDHSYNR 0x416 -#define LDVDLNR 0x418 -#define LDVTLNR 0x41a -#define LDVSYNR 0x41c -#define LDACLNR 0x41e -#define LDINTR 0x420 -#define LDPMMR 0x424 -#define LDPSPR 0x426 -#define LDCNTR 0x428 -#define LDCNTR_DON (1 << 0) -#define LDCNTR_DON2 (1 << 4) - -#ifdef CONFIG_CPU_SUBTYPE_SH7763 -# define LDLIRNR 0x440 -/* LDINTR bit */ -# define LDINTR_MINTEN (1 << 15) -# define LDINTR_FINTEN (1 << 14) -# define LDINTR_VSINTEN (1 << 13) -# define LDINTR_VEINTEN (1 << 12) -# define LDINTR_MINTS (1 << 11) -# define LDINTR_FINTS (1 << 10) -# define LDINTR_VSINTS (1 << 9) -# define LDINTR_VEINTS (1 << 8) -# define VINT_START (LDINTR_VSINTEN) -# define VINT_CHECK (LDINTR_VSINTS) -#else -/* LDINTR bit */ -# define LDINTR_VINTSEL (1 << 12) -# define LDINTR_VINTE (1 << 8) -# define LDINTR_VINTS (1 << 0) -# define VINT_START (LDINTR_VINTSEL) -# define VINT_CHECK (LDINTR_VINTS) -#endif - -/* HSYNC polarity inversion */ -#define LDMTR_FLMPOL (1 << 15) - -/* VSYNC polarity inversion */ -#define LDMTR_CL1POL (1 << 14) - -/* DISPLAY-ENABLE polarity inversion */ -#define LDMTR_DISPEN_LOWACT (1 << 13) - -/* DISPLAY DATA BUS polarity inversion */ -#define LDMTR_DPOL_LOWACT (1 << 12) - -/* AC modulation signal enable */ -#define LDMTR_MCNT (1 << 10) - -/* Disable output of HSYNC during VSYNC period */ -#define LDMTR_CL1CNT (1 << 9) - -/* Disable output of VSYNC during VSYNC period */ -#define LDMTR_CL2CNT (1 << 8) - -/* Display types supported by the LCDC */ -#define LDMTR_STN_MONO_4 0x00 -#define LDMTR_STN_MONO_8 0x01 -#define LDMTR_STN_COLOR_4 0x08 -#define LDMTR_STN_COLOR_8 0x09 -#define LDMTR_STN_COLOR_12 0x0A -#define LDMTR_STN_COLOR_16 0x0B -#define LDMTR_DSTN_MONO_8 0x11 -#define LDMTR_DSTN_MONO_16 0x13 -#define LDMTR_DSTN_COLOR_8 0x19 -#define LDMTR_DSTN_COLOR_12 0x1A -#define LDMTR_DSTN_COLOR_16 0x1B -#define LDMTR_TFT_COLOR_16 0x2B - -/* framebuffer color layout */ -#define LDDFR_1BPP_MONO 0x00 -#define LDDFR_2BPP_MONO 0x01 -#define LDDFR_4BPP_MONO 0x02 -#define LDDFR_6BPP_MONO 0x04 -#define LDDFR_4BPP 0x0A -#define LDDFR_8BPP 0x0C -#define LDDFR_16BPP_RGB555 0x1D -#define LDDFR_16BPP_RGB565 0x2D - -/* LCDC Pixclock sources */ -#define LCDC_CLKSRC_BUSCLOCK 0 -#define LCDC_CLKSRC_PERIPHERAL 1 -#define LCDC_CLKSRC_EXTERNAL 2 - -#define LDICKR_CLKSRC(x) \ - (((x) & 3) << 12) - -/* LCDC pixclock input divider. Set to 1 at a minimum! */ -#define LDICKR_CLKDIV(x) \ - ((x) & 0x1f) - -struct sh7760fb_platdata { - - /* Set this member to a valid fb_videmode for the display you - * wish to use. The following members must be initialized: - * xres, yres, hsync_len, vsync_len, sync, - * {left,right,upper,lower}_margin. - * The driver uses the above members to calculate register values - * and memory requirements. Other members are ignored but may - * be used by other framebuffer layer components. - */ - struct fb_videomode *def_mode; - - /* LDMTR includes display type and signal polarity. The - * HSYNC/VSYNC polarities are derived from the fb_var_screeninfo - * data above; however the polarities of the following signals - * must be encoded in the ldmtr member: - * Display Enable signal (default high-active) DISPEN_LOWACT - * Display Data signals (default high-active) DPOL_LOWACT - * AC Modulation signal (default off) MCNT - * Hsync-During-Vsync suppression (default off) CL1CNT - * Vsync-during-vsync suppression (default off) CL2CNT - * NOTE: also set a display type! - * (one of LDMTR_{STN,DSTN,TFT}_{MONO,COLOR}_{4,8,12,16}) - */ - u16 ldmtr; - - /* LDDFR controls framebuffer image format (depth, organization) - * Use ONE of the LDDFR_?BPP_* macros! - */ - u16 lddfr; - - /* LDPMMR and LDPSPR control the timing of the power signals - * for the display. Please read the SH7760 Hardware Manual, - * Chapters 30.3.17, 30.3.18 and 30.4.6! - */ - u16 ldpmmr; - u16 ldpspr; - - /* LDACLNR contains the line numbers after which the AC modulation - * signal is to toggle. Set to ZERO for TFTs or displays which - * do not need it. (Chapter 30.3.15 in SH7760 Hardware Manual). - */ - u16 ldaclnr; - - /* LDICKR contains information on pixelclock source and config. - * Please use the LDICKR_CLKSRC() and LDICKR_CLKDIV() macros. - * minimal value for CLKDIV() must be 1!. - */ - u16 ldickr; - - /* set this member to 1 if you wish to use the LCDC's hardware - * rotation function. This is limited to displays <= 320x200 - * pixels resolution! - */ - int rotate; /* set to 1 to rotate 90 CCW */ - - /* set this to 1 to suppress vsync irq use. */ - int novsync; - - /* blanking hook for platform. Set this if your platform can do - * more than the LCDC in terms of blanking (e.g. disable clock - * generator / backlight power supply / etc. - */ - void (*blank) (int); -}; - -#endif /* _ASM_SH_SH7760FB_H */ |