diff options
Diffstat (limited to 'include/asm-sh/mpc1211')
| -rw-r--r-- | include/asm-sh/mpc1211/dma.h | 304 | ||||
| -rw-r--r-- | include/asm-sh/mpc1211/io.h | 22 | ||||
| -rw-r--r-- | include/asm-sh/mpc1211/keyboard.h | 64 | ||||
| -rw-r--r-- | include/asm-sh/mpc1211/m1543c.h | 200 | ||||
| -rw-r--r-- | include/asm-sh/mpc1211/mc146818rtc.h | 6 | ||||
| -rw-r--r-- | include/asm-sh/mpc1211/mpc1211.h | 18 | ||||
| -rw-r--r-- | include/asm-sh/mpc1211/pci.h | 40 |
7 files changed, 654 insertions, 0 deletions
diff --git a/include/asm-sh/mpc1211/dma.h b/include/asm-sh/mpc1211/dma.h new file mode 100644 index 0000000..0a2fdab --- /dev/null +++ b/include/asm-sh/mpc1211/dma.h @@ -0,0 +1,304 @@ +/* $Id: dma.h,v 1.7 1992/12/14 00:29:34 root Exp root $ + * linux/include/asm/dma.h: Defines for using and allocating dma channels. + * Written by Hennus Bergman, 1992. + * High DMA channel support & info by Hannu Savolainen + * and John Boyd, Nov. 1992. + */ + +#ifndef _ASM_MPC1211_DMA_H +#define _ASM_MPC1211_DMA_H + +#include <linux/config.h> +#include <linux/spinlock.h> /* And spinlocks */ +#include <asm/io.h> /* need byte IO */ +#include <linux/delay.h> + + +#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER +#define dma_outb outb_p +#else +#define dma_outb outb +#endif + +#define dma_inb inb + +/* + * NOTES about DMA transfers: + * + * controller 1: channels 0-3, byte operations, ports 00-1F + * controller 2: channels 4-7, word operations, ports C0-DF + * + * - ALL registers are 8 bits only, regardless of transfer size + * - channel 4 is not used - cascades 1 into 2. + * - channels 0-3 are byte - addresses/counts are for physical bytes + * - channels 5-7 are word - addresses/counts are for physical words + * - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries + * - transfer count loaded to registers is 1 less than actual count + * - controller 2 offsets are all even (2x offsets for controller 1) + * - page registers for 5-7 don't use data bit 0, represent 128K pages + * - page registers for 0-3 use bit 0, represent 64K pages + * + * DMA transfers are limited to the lower 16MB of _physical_ memory. + * Note that addresses loaded into registers must be _physical_ addresses, + * not logical addresses (which may differ if paging is active). + * + * Address mapping for channels 0-3: + * + * A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses) + * | ... | | ... | | ... | + * | ... | | ... | | ... | + * | ... | | ... | | ... | + * P7 ... P0 A7 ... A0 A7 ... A0 + * | Page | Addr MSB | Addr LSB | (DMA registers) + * + * Address mapping for channels 5-7: + * + * A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses) + * | ... | \ \ ... \ \ \ ... \ \ + * | ... | \ \ ... \ \ \ ... \ (not used) + * | ... | \ \ ... \ \ \ ... \ + * P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0 + * | Page | Addr MSB | Addr LSB | (DMA registers) + * + * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses + * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at + * the hardware level, so odd-byte transfers aren't possible). + * + * Transfer count (_not # bytes_) is limited to 64K, represented as actual + * count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more, + * and up to 128K bytes may be transferred on channels 5-7 in one operation. + * + */ + +#define MAX_DMA_CHANNELS 8 + +/* The maximum address that we can perform a DMA transfer to on this platform */ +#define MAX_DMA_ADDRESS (PAGE_OFFSET+0x10000000) + +/* 8237 DMA controllers */ +#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */ +#define IO_DMA2_BASE 0xC0 /* 16 bit master DMA, ch 4(=slave input)..7 */ + +/* DMA controller registers */ +#define DMA1_CMD_REG 0x08 /* command register (w) */ +#define DMA1_STAT_REG 0x08 /* status register (r) */ +#define DMA1_REQ_REG 0x09 /* request register (w) */ +#define DMA1_MASK_REG 0x0A /* single-channel mask (w) */ +#define DMA1_MODE_REG 0x0B /* mode register (w) */ +#define DMA1_CLEAR_FF_REG 0x0C /* clear pointer flip-flop (w) */ +#define DMA1_TEMP_REG 0x0D /* Temporary Register (r) */ +#define DMA1_RESET_REG 0x0D /* Master Clear (w) */ +#define DMA1_CLR_MASK_REG 0x0E /* Clear Mask */ +#define DMA1_MASK_ALL_REG 0x0F /* all-channels mask (w) */ + +#define DMA2_CMD_REG 0xD0 /* command register (w) */ +#define DMA2_STAT_REG 0xD0 /* status register (r) */ +#define DMA2_REQ_REG 0xD2 /* request register (w) */ +#define DMA2_MASK_REG 0xD4 /* single-channel mask (w) */ +#define DMA2_MODE_REG 0xD6 /* mode register (w) */ +#define DMA2_CLEAR_FF_REG 0xD8 /* clear pointer flip-flop (w) */ +#define DMA2_TEMP_REG 0xDA /* Temporary Register (r) */ +#define DMA2_RESET_REG 0xDA /* Master Clear (w) */ +#define DMA2_CLR_MASK_REG 0xDC /* Clear Mask */ +#define DMA2_MASK_ALL_REG 0xDE /* all-channels mask (w) */ + +#define DMA_ADDR_0 0x00 /* DMA address registers */ +#define DMA_ADDR_1 0x02 +#define DMA_ADDR_2 0x04 +#define DMA_ADDR_3 0x06 +#define DMA_ADDR_4 0xC0 +#define DMA_ADDR_5 0xC4 +#define DMA_ADDR_6 0xC8 +#define DMA_ADDR_7 0xCC + +#define DMA_CNT_0 0x01 /* DMA count registers */ +#define DMA_CNT_1 0x03 +#define DMA_CNT_2 0x05 +#define DMA_CNT_3 0x07 +#define DMA_CNT_4 0xC2 +#define DMA_CNT_5 0xC6 +#define DMA_CNT_6 0xCA +#define DMA_CNT_7 0xCE + +#define DMA_PAGE_0 0x87 /* DMA page registers */ +#define DMA_PAGE_1 0x83 +#define DMA_PAGE_2 0x81 +#define DMA_PAGE_3 0x82 +#define DMA_PAGE_5 0x8B +#define DMA_PAGE_6 0x89 +#define DMA_PAGE_7 0x8A + +#define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */ +#define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */ +#define DMA_MODE_CASCADE 0xC0 /* pass thru DREQ->HRQ, DACK<-HLDA only */ + +#define DMA_AUTOINIT 0x10 + + +extern spinlock_t dma_spin_lock; + +static __inline__ unsigned long claim_dma_lock(void) +{ + unsigned long flags; + spin_lock_irqsave(&dma_spin_lock, flags); + return flags; +} + +static __inline__ void release_dma_lock(unsigned long flags) +{ + spin_unlock_irqrestore(&dma_spin_lock, flags); +} + +/* enable/disable a specific DMA channel */ +static __inline__ void enable_dma(unsigned int dmanr) +{ + if (dmanr<=3) + dma_outb(dmanr, DMA1_MASK_REG); + else + dma_outb(dmanr & 3, DMA2_MASK_REG); +} + +static __inline__ void disable_dma(unsigned int dmanr) +{ + if (dmanr<=3) + dma_outb(dmanr | 4, DMA1_MASK_REG); + else + dma_outb((dmanr & 3) | 4, DMA2_MASK_REG); +} + +/* Clear the 'DMA Pointer Flip Flop'. + * Write 0 for LSB/MSB, 1 for MSB/LSB access. + * Use this once to initialize the FF to a known state. + * After that, keep track of it. :-) + * --- In order to do that, the DMA routines below should --- + * --- only be used while holding the DMA lock ! --- + */ +static __inline__ void clear_dma_ff(unsigned int dmanr) +{ + if (dmanr<=3) + dma_outb(0, DMA1_CLEAR_FF_REG); + else + dma_outb(0, DMA2_CLEAR_FF_REG); +} + +/* set mode (above) for a specific DMA channel */ +static __inline__ void set_dma_mode(unsigned int dmanr, char mode) +{ + if (dmanr<=3) + dma_outb(mode | dmanr, DMA1_MODE_REG); + else + dma_outb(mode | (dmanr&3), DMA2_MODE_REG); +} + +/* Set only the page register bits of the transfer address. + * This is used for successive transfers when we know the contents of + * the lower 16 bits of the DMA current address register, but a 64k boundary + * may have been crossed. + */ +static __inline__ void set_dma_page(unsigned int dmanr, unsigned int pagenr) +{ + switch(dmanr) { + case 0: + dma_outb( pagenr & 0xff, DMA_PAGE_0); + dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_0 + 0x400); + break; + case 1: + dma_outb( pagenr & 0xff, DMA_PAGE_1); + dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_1 + 0x400); + break; + case 2: + dma_outb( pagenr & 0xff, DMA_PAGE_2); + dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_2 + 0x400); + break; + case 3: + dma_outb( pagenr & 0xff, DMA_PAGE_3); + dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_3 + 0x400); + break; + case 5: + dma_outb( pagenr & 0xfe, DMA_PAGE_5); + dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_5 + 0x400); + break; + case 6: + dma_outb( pagenr & 0xfe, DMA_PAGE_6); + dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_6 + 0x400); + break; + case 7: + dma_outb( pagenr & 0xfe, DMA_PAGE_7); + dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_7 + 0x400); + break; + } +} + + +/* Set transfer address & page bits for specific DMA channel. + * Assumes dma flipflop is clear. + */ +static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a) +{ + set_dma_page(dmanr, a>>16); + if (dmanr <= 3) { + dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE ); + dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE ); + } else { + dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE ); + dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE ); + } +} + + +/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for + * a specific DMA channel. + * You must ensure the parameters are valid. + * NOTE: from a manual: "the number of transfers is one more + * than the initial word count"! This is taken into account. + * Assumes dma flip-flop is clear. + * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7. + */ +static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count) +{ + count--; + if (dmanr <= 3) { + dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE ); + dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE ); + } else { + dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE ); + dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE ); + } +} + + +/* Get DMA residue count. After a DMA transfer, this + * should return zero. Reading this while a DMA transfer is + * still in progress will return unpredictable results. + * If called before the channel has been used, it may return 1. + * Otherwise, it returns the number of _bytes_ left to transfer. + * + * Assumes DMA flip-flop is clear. + */ +static __inline__ int get_dma_residue(unsigned int dmanr) +{ + unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE + : ((dmanr&3)<<2) + 2 + IO_DMA2_BASE; + + /* using short to get 16-bit wrap around */ + unsigned short count; + + count = 1 + dma_inb(io_port); + count += dma_inb(io_port) << 8; + return (dmanr<=3)? count : (count<<1); +} + + +/* These are in kernel/dma.c: */ +extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */ +extern void free_dma(unsigned int dmanr); /* release it again */ + +/* From PCI */ + +#ifdef CONFIG_PCI +extern int isa_dma_bridge_buggy; +#else +#define isa_dma_bridge_buggy (0) +#endif + +#endif /* _ASM_MPC1211_DMA_H */ diff --git a/include/asm-sh/mpc1211/io.h b/include/asm-sh/mpc1211/io.h new file mode 100644 index 0000000..eba8a0b --- /dev/null +++ b/include/asm-sh/mpc1211/io.h @@ -0,0 +1,22 @@ +/* + * include/asm-sh/io_mpc1211.h + * + * Copyright 2001 Saito.K & Jeanne + * + * IO functions for an Interface MPC-1211 + */ + +#ifndef _ASM_SH_IO_MPC1211_H +#define _ASM_SH_IO_MPC1211_H + +#include <linux/time.h> + +extern int mpc1211_irq_demux(int irq); + +extern void init_mpc1211_IRQ(void); +extern void heartbeat_mpc1211(void); + +extern void mpc1211_rtc_gettimeofday(struct timeval *tv); +extern int mpc1211_rtc_settimeofday(const struct timeval *tv); + +#endif /* _ASM_SH_IO_MPC1211_H */ diff --git a/include/asm-sh/mpc1211/keyboard.h b/include/asm-sh/mpc1211/keyboard.h new file mode 100644 index 0000000..5f0b908 --- /dev/null +++ b/include/asm-sh/mpc1211/keyboard.h @@ -0,0 +1,64 @@ +/* + * MPC1211 specific keybord definitions + * Taken from the old asm-i386/keybord.h for PC/AT-style definitions + * created 3 Nov 1996 by Geert Uytterhoeven. + */ + +#ifdef __KERNEL__ + +#include <linux/kernel.h> +#include <linux/ioport.h> +#include <linux/kd.h> +#include <linux/pm.h> +#include <asm/io.h> + +#define KEYBOARD_IRQ 1 +#define DISABLE_KBD_DURING_INTERRUPTS 0 + +extern int pckbd_setkeycode(unsigned int scancode, unsigned int keycode); +extern int pckbd_getkeycode(unsigned int scancode); +extern int pckbd_translate(unsigned char scancode, unsigned char *keycode, + char raw_mode); +extern char pckbd_unexpected_up(unsigned char keycode); +extern void pckbd_leds(unsigned char leds); +extern void pckbd_init_hw(void); +extern int pckbd_pm_resume(struct pm_dev *, pm_request_t, void *); +extern pm_callback pm_kbd_request_override; +extern unsigned char pckbd_sysrq_xlate[128]; + +#define kbd_setkeycode pckbd_setkeycode +#define kbd_getkeycode pckbd_getkeycode +#define kbd_translate pckbd_translate +#define kbd_unexpected_up pckbd_unexpected_up +#define kbd_leds pckbd_leds +#define kbd_init_hw pckbd_init_hw +#define kbd_sysrq_xlate pckbd_sysrq_xlate + +#define SYSRQ_KEY 0x54 + +/* resource allocation */ +#define kbd_request_region() +#define kbd_request_irq(handler) request_irq(KEYBOARD_IRQ, handler, 0, \ + "keyboard", NULL) + +/* How to access the keyboard macros on this platform. */ +#define kbd_read_input() inb(KBD_DATA_REG) +#define kbd_read_status() inb(KBD_STATUS_REG) +#define kbd_write_output(val) outb(val, KBD_DATA_REG) +#define kbd_write_command(val) outb(val, KBD_CNTL_REG) + +/* Some stoneage hardware needs delays after some operations. */ +#define kbd_pause() do { } while(0) + +/* + * Machine specific bits for the PS/2 driver + */ + +#define AUX_IRQ 12 + +#define aux_request_irq(hand, dev_id) \ + request_irq(AUX_IRQ, hand, SA_SHIRQ, "PS2 Mouse", dev_id) + +#define aux_free_irq(dev_id) free_irq(AUX_IRQ, dev_id) + +#endif /* __KERNEL__ */ diff --git a/include/asm-sh/mpc1211/m1543c.h b/include/asm-sh/mpc1211/m1543c.h new file mode 100644 index 0000000..c95d132 --- /dev/null +++ b/include/asm-sh/mpc1211/m1543c.h @@ -0,0 +1,200 @@ +#ifndef __ASM_SH_M1543C_H +#define __ASM_SH_M1543C_H + +/* + * linux/include/asm-sh/m1543c.h + * Copyright (C) 2001 Nobuhiro Sakawa + * M1543C:PCI-ISA Bus Bridge with Super IO Chip support + * + * from + * + * linux/include/asm-sh/smc37c93x.h + * + * Copyright (C) 2000 Kazumoto Kojima + * + * SMSC 37C93x Super IO Chip support + */ + +/* Default base I/O address */ +#define FDC_PRIMARY_BASE 0x3f0 +#define IDE1_PRIMARY_BASE 0x1f0 +#define IDE1_SECONDARY_BASE 0x170 +#define PARPORT_PRIMARY_BASE 0x378 +#define COM1_PRIMARY_BASE 0x2f8 +#define COM2_PRIMARY_BASE 0x3f8 +#define COM3_PRIMARY_BASE 0x3e8 +#define RTC_PRIMARY_BASE 0x070 +#define KBC_PRIMARY_BASE 0x060 +#define AUXIO_PRIMARY_BASE 0x000 /* XXX */ +#define I8259_M_CR 0x20 +#define I8259_M_MR 0x21 +#define I8259_S_CR 0xa0 +#define I8259_S_MR 0xa1 + +/* Logical device number */ +#define LDN_FDC 0 +#define LDN_IDE1 1 +#define LDN_IDE2 2 +#define LDN_PARPORT 3 +#define LDN_COM1 4 +#define LDN_COM2 5 +#define LDN_COM3 11 +#define LDN_RTC 6 +#define LDN_KBC 7 + +/* Configuration port and key */ +#define CONFIG_PORT 0x3f0 +#define INDEX_PORT CONFIG_PORT +#define DATA_PORT 0x3f1 +#define CONFIG_ENTER1 0x51 +#define CONFIG_ENTER2 0x23 +#define CONFIG_EXIT 0xbb + +/* Configuration index */ +#define CURRENT_LDN_INDEX 0x07 +#define POWER_CONTROL_INDEX 0x22 +#define ACTIVATE_INDEX 0x30 +#define IO_BASE_HI_INDEX 0x60 +#define IO_BASE_LO_INDEX 0x61 +#define IRQ_SELECT_INDEX 0x70 +#define PS2_IRQ_INDEX 0x72 +#define DMA_SELECT_INDEX 0x74 + +/* UART stuff. Only for debugging. */ +/* UART Register */ + +#define UART_RBR 0x0 /* Receiver Buffer Register (Read Only) */ +#define UART_THR 0x0 /* Transmitter Holding Register (Write Only) */ +#define UART_IER 0x2 /* Interrupt Enable Register */ +#define UART_IIR 0x4 /* Interrupt Ident Register (Read Only) */ +#define UART_FCR 0x4 /* FIFO Control Register (Write Only) */ +#define UART_LCR 0x6 /* Line Control Register */ +#define UART_MCR 0x8 /* MODEM Control Register */ +#define UART_LSR 0xa /* Line Status Register */ +#define UART_MSR 0xc /* MODEM Status Register */ +#define UART_SCR 0xe /* Scratch Register */ +#define UART_DLL 0x0 /* Divisor Latch (LS) */ +#define UART_DLM 0x2 /* Divisor Latch (MS) */ + +#ifndef __ASSEMBLY__ +typedef struct uart_reg { + volatile __u16 rbr; + volatile __u16 ier; + volatile __u16 iir; + volatile __u16 lcr; + volatile __u16 mcr; + volatile __u16 lsr; + volatile __u16 msr; + volatile __u16 scr; +} uart_reg; +#endif /* ! __ASSEMBLY__ */ + +/* Alias for Write Only Register */ + +#define thr rbr +#define tcr iir + +/* Alias for Divisor Latch Register */ + +#define dll rbr +#define dlm ier +#define fcr iir + +/* Interrupt Enable Register */ + +#define IER_ERDAI 0x0100 /* Enable Received Data Available Interrupt */ +#define IER_ETHREI 0x0200 /* Enable Transmitter Holding Register Empty Interrupt */ +#define IER_ELSI 0x0400 /* Enable Receiver Line Status Interrupt */ +#define IER_EMSI 0x0800 /* Enable MODEM Status Interrupt */ + +/* Interrupt Ident Register */ + +#define IIR_IP 0x0100 /* "0" if Interrupt Pending */ +#define IIR_IIB0 0x0200 /* Interrupt ID Bit 0 */ +#define IIR_IIB1 0x0400 /* Interrupt ID Bit 1 */ +#define IIR_IIB2 0x0800 /* Interrupt ID Bit 2 */ +#define IIR_FIFO 0xc000 /* FIFOs enabled */ + +/* FIFO Control Register */ + +#define FCR_FEN 0x0100 /* FIFO enable */ +#define FCR_RFRES 0x0200 /* Receiver FIFO reset */ +#define FCR_TFRES 0x0400 /* Transmitter FIFO reset */ +#define FCR_DMA 0x0800 /* DMA mode select */ +#define FCR_RTL 0x4000 /* Receiver triger (LSB) */ +#define FCR_RTM 0x8000 /* Receiver triger (MSB) */ + +/* Line Control Register */ + +#define LCR_WLS0 0x0100 /* Word Length Select Bit 0 */ +#define LCR_WLS1 0x0200 /* Word Length Select Bit 1 */ +#define LCR_STB 0x0400 /* Number of Stop Bits */ +#define LCR_PEN 0x0800 /* Parity Enable */ +#define LCR_EPS 0x1000 /* Even Parity Select */ +#define LCR_SP 0x2000 /* Stick Parity */ +#define LCR_SB 0x4000 /* Set Break */ +#define LCR_DLAB 0x8000 /* Divisor Latch Access Bit */ + +/* MODEM Control Register */ + +#define MCR_DTR 0x0100 /* Data Terminal Ready */ +#define MCR_RTS 0x0200 /* Request to Send */ +#define MCR_OUT1 0x0400 /* Out 1 */ +#define MCR_IRQEN 0x0800 /* IRQ Enable */ +#define MCR_LOOP 0x1000 /* Loop */ + +/* Line Status Register */ + +#define LSR_DR 0x0100 /* Data Ready */ +#define LSR_OE 0x0200 /* Overrun Error */ +#define LSR_PE 0x0400 /* Parity Error */ +#define LSR_FE 0x0800 /* Framing Error */ +#define LSR_BI 0x1000 /* Break Interrupt */ +#define LSR_THRE 0x2000 /* Transmitter Holding Register Empty */ +#define LSR_TEMT 0x4000 /* Transmitter Empty */ +#define LSR_FIFOE 0x8000 /* Receiver FIFO error */ + +/* MODEM Status Register */ + +#define MSR_DCTS 0x0100 /* Delta Clear to Send */ +#define MSR_DDSR 0x0200 /* Delta Data Set Ready */ +#define MSR_TERI 0x0400 /* Trailing Edge Ring Indicator */ +#define MSR_DDCD 0x0800 /* Delta Data Carrier Detect */ +#define MSR_CTS 0x1000 /* Clear to Send */ +#define MSR_DSR 0x2000 /* Data Set Ready */ +#define MSR_RI 0x4000 /* Ring Indicator */ +#define MSR_DCD 0x8000 /* Data Carrier Detect */ + +/* Baud Rate Divisor */ + +#define UART_CLK (1843200) /* 1.8432 MHz */ +#define UART_BAUD(x) (UART_CLK / (16 * (x))) + +/* RTC register definition */ +#define RTC_SECONDS 0 +#define RTC_SECONDS_ALARM 1 +#define RTC_MINUTES 2 +#define RTC_MINUTES_ALARM 3 +#define RTC_HOURS 4 +#define RTC_HOURS_ALARM 5 +#define RTC_DAY_OF_WEEK 6 +#define RTC_DAY_OF_MONTH 7 +#define RTC_MONTH 8 +#define RTC_YEAR 9 +#define RTC_FREQ_SELECT 10 +# define RTC_UIP 0x80 +# define RTC_DIV_CTL 0x70 +/* This RTC can work under 32.768KHz clock only. */ +# define RTC_OSC_ENABLE 0x20 +# define RTC_OSC_DISABLE 0x00 +#define RTC_CONTROL 11 +# define RTC_SET 0x80 +# define RTC_PIE 0x40 +# define RTC_AIE 0x20 +# define RTC_UIE 0x10 +# define RTC_SQWE 0x08 +# define RTC_DM_BINARY 0x04 +# define RTC_24H 0x02 +# define RTC_DST_EN 0x01 + +#endif /* __ASM_SH_M1543C_H */ diff --git a/include/asm-sh/mpc1211/mc146818rtc.h b/include/asm-sh/mpc1211/mc146818rtc.h new file mode 100644 index 0000000..0ec78f6 --- /dev/null +++ b/include/asm-sh/mpc1211/mc146818rtc.h @@ -0,0 +1,6 @@ +/* + * MPC1211 uses PC/AT style RTC definitions. + */ +#include <asm-i386/mc146818rtc.h> + + diff --git a/include/asm-sh/mpc1211/mpc1211.h b/include/asm-sh/mpc1211/mpc1211.h new file mode 100644 index 0000000..fa456c3 --- /dev/null +++ b/include/asm-sh/mpc1211/mpc1211.h @@ -0,0 +1,18 @@ +#ifndef __ASM_SH_MPC1211_H +#define __ASM_SH_MPC1211_H + +/* + * linux/include/asm-sh/mpc1211.h + * + * Copyright (C) 2001 Saito.K & Jeanne + * + * Interface MPC-1211 support + */ + +#define PA_PCI_IO (0xa4000000) /* PCI I/O space */ +#define PA_PCI_MEM (0xb0000000) /* PCI MEM space */ + +#define PCIPAR (0xa4000cf8) /* PCI Config address */ +#define PCIPDR (0xa4000cfc) /* PCI Config data */ + +#endif /* __ASM_SH_MPC1211_H */ diff --git a/include/asm-sh/mpc1211/pci.h b/include/asm-sh/mpc1211/pci.h new file mode 100644 index 0000000..5d3712c --- /dev/null +++ b/include/asm-sh/mpc1211/pci.h @@ -0,0 +1,40 @@ +/* + * Low-Level PCI Support for MPC-1211 + * + * (c) 2002 Saito.K & Jeanne + * + */ + +#ifndef _PCI_MPC1211_H_ +#define _PCI_MPC1211_H_ + +#include <linux/pci.h> + +/* set debug level 4=verbose...1=terse */ +//#define DEBUG_PCI 3 +#undef DEBUG_PCI + +#ifdef DEBUG_PCI +#define PCIDBG(n, x...) { if(DEBUG_PCI>=n) printk(x); } +#else +#define PCIDBG(n, x...) +#endif + +/* startup values */ +#define PCI_PROBE_BIOS 1 +#define PCI_PROBE_CONF1 2 +#define PCI_PROBE_CONF2 4 +#define PCI_NO_SORT 0x100 +#define PCI_BIOS_SORT 0x200 +#define PCI_NO_CHECKS 0x400 +#define PCI_ASSIGN_ROMS 0x1000 +#define PCI_BIOS_IRQ_SCAN 0x2000 + +/* MPC-1211 Specific Values */ +#define PCIPAR (0xa4000cf8) /* PCI Config address */ +#define PCIPDR (0xa4000cfc) /* PCI Config data */ + +#define PA_PCI_IO (0xa4000000) /* PCI I/O space */ +#define PA_PCI_MEM (0xb0000000) /* PCI MEM space */ + +#endif /* _PCI_MPC1211_H_ */ |
