summaryrefslogtreecommitdiffstats
path: root/include/asm-ppc/uninorth.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/asm-ppc/uninorth.h')
-rw-r--r--include/asm-ppc/uninorth.h229
1 files changed, 229 insertions, 0 deletions
diff --git a/include/asm-ppc/uninorth.h b/include/asm-ppc/uninorth.h
new file mode 100644
index 0000000..f737732
--- /dev/null
+++ b/include/asm-ppc/uninorth.h
@@ -0,0 +1,229 @@
+/*
+ * uninorth.h: definitions for using the "UniNorth" host bridge chip
+ * from Apple. This chip is used on "Core99" machines
+ * This also includes U2 used on more recent MacRISC2/3
+ * machines and U3 (G5)
+ *
+ */
+#ifdef __KERNEL__
+#ifndef __ASM_UNINORTH_H__
+#define __ASM_UNINORTH_H__
+
+/*
+ * Uni-N and U3 config space reg. definitions
+ *
+ * (Little endian)
+ */
+
+/* Address ranges selection. This one should work with Bandit too */
+/* Not U3 */
+#define UNI_N_ADDR_SELECT 0x48
+#define UNI_N_ADDR_COARSE_MASK 0xffff0000 /* 256Mb regions at *0000000 */
+#define UNI_N_ADDR_FINE_MASK 0x0000ffff /* 16Mb regions at f*000000 */
+
+/* AGP registers */
+/* Not U3 */
+#define UNI_N_CFG_GART_BASE 0x8c
+#define UNI_N_CFG_AGP_BASE 0x90
+#define UNI_N_CFG_GART_CTRL 0x94
+#define UNI_N_CFG_INTERNAL_STATUS 0x98
+#define UNI_N_CFG_GART_DUMMY_PAGE 0xa4
+
+/* UNI_N_CFG_GART_CTRL bits definitions */
+#define UNI_N_CFG_GART_INVAL 0x00000001
+#define UNI_N_CFG_GART_ENABLE 0x00000100
+#define UNI_N_CFG_GART_2xRESET 0x00010000
+#define UNI_N_CFG_GART_DISSBADET 0x00020000
+/* The following seems to only be used only on U3 <j.glisse@gmail.com> */
+#define U3_N_CFG_GART_SYNCMODE 0x00040000
+#define U3_N_CFG_GART_PERFRD 0x00080000
+#define U3_N_CFG_GART_B2BGNT 0x00200000
+#define U3_N_CFG_GART_FASTDDR 0x00400000
+
+/* My understanding of UniNorth AGP as of UniNorth rev 1.0x,
+ * revision 1.5 (x4 AGP) may need further changes.
+ *
+ * AGP_BASE register contains the base address of the AGP aperture on
+ * the AGP bus. It doesn't seem to be visible to the CPU as of UniNorth 1.x,
+ * even if decoding of this address range is enabled in the address select
+ * register. Apparently, the only supported bases are 256Mb multiples
+ * (high 4 bits of that register).
+ *
+ * GART_BASE register appear to contain the physical address of the GART
+ * in system memory in the high address bits (page aligned), and the
+ * GART size in the low order bits (number of GART pages)
+ *
+ * The GART format itself is one 32bits word per physical memory page.
+ * This word contains, in little-endian format (!!!), the physical address
+ * of the page in the high bits, and what appears to be an "enable" bit
+ * in the LSB bit (0) that must be set to 1 when the entry is valid.
+ *
+ * Obviously, the GART is not cache coherent and so any change to it
+ * must be flushed to memory (or maybe just make the GART space non
+ * cachable). AGP memory itself doens't seem to be cache coherent neither.
+ *
+ * In order to invalidate the GART (which is probably necessary to inval
+ * the bridge internal TLBs), the following sequence has to be written,
+ * in order, to the GART_CTRL register:
+ *
+ * UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL
+ * UNI_N_CFG_GART_ENABLE
+ * UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_2xRESET
+ * UNI_N_CFG_GART_ENABLE
+ *
+ * As far as AGP "features" are concerned, it looks like fast write may
+ * not be supported but this has to be confirmed.
+ *
+ * Turning on AGP seem to require a double invalidate operation, one before
+ * setting the AGP command register, on after.
+ *
+ * Turning off AGP seems to require the following sequence: first wait
+ * for the AGP to be idle by reading the internal status register, then
+ * write in that order to the GART_CTRL register:
+ *
+ * UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL
+ * 0
+ * UNI_N_CFG_GART_2xRESET
+ * 0
+ */
+
+/*
+ * Uni-N memory mapped reg. definitions
+ *
+ * Those registers are Big-Endian !!
+ *
+ * Their meaning come from either Darwin and/or from experiments I made with
+ * the bootrom, I'm not sure about their exact meaning yet
+ *
+ */
+
+/* Version of the UniNorth chip */
+#define UNI_N_VERSION 0x0000 /* Known versions: 3,7 and 8 */
+
+#define UNI_N_VERSION_107 0x0003 /* 1.0.7 */
+#define UNI_N_VERSION_10A 0x0007 /* 1.0.10 */
+#define UNI_N_VERSION_150 0x0011 /* 1.5 */
+#define UNI_N_VERSION_200 0x0024 /* 2.0 */
+#define UNI_N_VERSION_PANGEA 0x00C0 /* Integrated U1 + K */
+#define UNI_N_VERSION_INTREPID 0x00D2 /* Integrated U2 + K */
+#define UNI_N_VERSION_300 0x0030 /* 3.0 (U3 on G5) */
+
+/* This register is used to enable/disable various clocks */
+#define UNI_N_CLOCK_CNTL 0x0020
+#define UNI_N_CLOCK_CNTL_PCI 0x00000001 /* PCI2 clock control */
+#define UNI_N_CLOCK_CNTL_GMAC 0x00000002 /* GMAC clock control */
+#define UNI_N_CLOCK_CNTL_FW 0x00000004 /* FireWire clock control */
+#define UNI_N_CLOCK_CNTL_ATA100 0x00000010 /* ATA-100 clock control (U2) */
+
+/* Power Management control */
+#define UNI_N_POWER_MGT 0x0030
+#define UNI_N_POWER_MGT_NORMAL 0x00
+#define UNI_N_POWER_MGT_IDLE2 0x01
+#define UNI_N_POWER_MGT_SLEEP 0x02
+
+/* This register is configured by Darwin depending on the UniN
+ * revision
+ */
+#define UNI_N_ARB_CTRL 0x0040
+#define UNI_N_ARB_CTRL_QACK_DELAY_SHIFT 15
+#define UNI_N_ARB_CTRL_QACK_DELAY_MASK 0x0e1f8000
+#define UNI_N_ARB_CTRL_QACK_DELAY 0x30
+#define UNI_N_ARB_CTRL_QACK_DELAY105 0x00
+
+/* This one _might_ return the CPU number of the CPU reading it;
+ * the bootROM decides whether to boot or to sleep/spinloop depending
+ * on this register beeing 0 or not
+ */
+#define UNI_N_CPU_NUMBER 0x0050
+
+/* This register appear to be read by the bootROM to decide what
+ * to do on a non-recoverable reset (powerup or wakeup)
+ */
+#define UNI_N_HWINIT_STATE 0x0070
+#define UNI_N_HWINIT_STATE_SLEEPING 0x01
+#define UNI_N_HWINIT_STATE_RUNNING 0x02
+/* This last bit appear to be used by the bootROM to know the second
+ * CPU has started and will enter it's sleep loop with IP=0
+ */
+#define UNI_N_HWINIT_STATE_CPU1_FLAG 0x10000000
+
+/* This register controls AACK delay, which is set when 2004 iBook/PowerBook
+ * is in low speed mode.
+ */
+#define UNI_N_AACK_DELAY 0x0100
+#define UNI_N_AACK_DELAY_ENABLE 0x00000001
+
+/* Clock status for Intrepid */
+#define UNI_N_CLOCK_STOP_STATUS0 0x0150
+#define UNI_N_CLOCK_STOPPED_EXTAGP 0x00200000
+#define UNI_N_CLOCK_STOPPED_AGPDEL 0x00100000
+#define UNI_N_CLOCK_STOPPED_I2S0_45_49 0x00080000
+#define UNI_N_CLOCK_STOPPED_I2S0_18 0x00040000
+#define UNI_N_CLOCK_STOPPED_I2S1_45_49 0x00020000
+#define UNI_N_CLOCK_STOPPED_I2S1_18 0x00010000
+#define UNI_N_CLOCK_STOPPED_TIMER 0x00008000
+#define UNI_N_CLOCK_STOPPED_SCC_RTCLK18 0x00004000
+#define UNI_N_CLOCK_STOPPED_SCC_RTCLK32 0x00002000
+#define UNI_N_CLOCK_STOPPED_SCC_VIA32 0x00001000
+#define UNI_N_CLOCK_STOPPED_SCC_SLOT0 0x00000800
+#define UNI_N_CLOCK_STOPPED_SCC_SLOT1 0x00000400
+#define UNI_N_CLOCK_STOPPED_SCC_SLOT2 0x00000200
+#define UNI_N_CLOCK_STOPPED_PCI_FBCLKO 0x00000100
+#define UNI_N_CLOCK_STOPPED_VEO0 0x00000080
+#define UNI_N_CLOCK_STOPPED_VEO1 0x00000040
+#define UNI_N_CLOCK_STOPPED_USB0 0x00000020
+#define UNI_N_CLOCK_STOPPED_USB1 0x00000010
+#define UNI_N_CLOCK_STOPPED_USB2 0x00000008
+#define UNI_N_CLOCK_STOPPED_32 0x00000004
+#define UNI_N_CLOCK_STOPPED_45 0x00000002
+#define UNI_N_CLOCK_STOPPED_49 0x00000001
+
+#define UNI_N_CLOCK_STOP_STATUS1 0x0160
+#define UNI_N_CLOCK_STOPPED_PLL4REF 0x00080000
+#define UNI_N_CLOCK_STOPPED_CPUDEL 0x00040000
+#define UNI_N_CLOCK_STOPPED_CPU 0x00020000
+#define UNI_N_CLOCK_STOPPED_BUF_REFCKO 0x00010000
+#define UNI_N_CLOCK_STOPPED_PCI2 0x00008000
+#define UNI_N_CLOCK_STOPPED_FW 0x00004000
+#define UNI_N_CLOCK_STOPPED_GB 0x00002000
+#define UNI_N_CLOCK_STOPPED_ATA66 0x00001000
+#define UNI_N_CLOCK_STOPPED_ATA100 0x00000800
+#define UNI_N_CLOCK_STOPPED_MAX 0x00000400
+#define UNI_N_CLOCK_STOPPED_PCI1 0x00000200
+#define UNI_N_CLOCK_STOPPED_KLPCI 0x00000100
+#define UNI_N_CLOCK_STOPPED_USB0PCI 0x00000080
+#define UNI_N_CLOCK_STOPPED_USB1PCI 0x00000040
+#define UNI_N_CLOCK_STOPPED_USB2PCI 0x00000020
+#define UNI_N_CLOCK_STOPPED_7PCI1 0x00000008
+#define UNI_N_CLOCK_STOPPED_AGP 0x00000004
+#define UNI_N_CLOCK_STOPPED_PCI0 0x00000002
+#define UNI_N_CLOCK_STOPPED_18 0x00000001
+
+/* Intrepid registe to OF do-platform-clockspreading */
+#define UNI_N_CLOCK_SPREADING 0x190
+
+/* Uninorth 1.5 rev. has additional perf. monitor registers at 0xf00-0xf50 */
+
+
+/*
+ * U3 specific registers
+ */
+
+
+/* U3 Toggle */
+#define U3_TOGGLE_REG 0x00e0
+#define U3_PMC_START_STOP 0x0001
+#define U3_MPIC_RESET 0x0002
+#define U3_MPIC_OUTPUT_ENABLE 0x0004
+
+/* U3 API PHY Config 1 */
+#define U3_API_PHY_CONFIG_1 0x23030
+
+/* U3 HyperTransport registers */
+#define U3_HT_CONFIG_BASE 0x70000
+#define U3_HT_LINK_COMMAND 0x100
+#define U3_HT_LINK_CONFIG 0x110
+#define U3_HT_LINK_FREQ 0x120
+
+#endif /* __ASM_UNINORTH_H__ */
+#endif /* __KERNEL__ */
OpenPOWER on IntegriCloud