diff options
Diffstat (limited to 'include/asm-mips/sgi')
| -rw-r--r-- | include/asm-mips/sgi/gio.h | 86 | ||||
| -rw-r--r-- | include/asm-mips/sgi/hpc3.h | 317 | ||||
| -rw-r--r-- | include/asm-mips/sgi/ioc.h | 200 | ||||
| -rw-r--r-- | include/asm-mips/sgi/ip22.h | 78 | ||||
| -rw-r--r-- | include/asm-mips/sgi/mc.h | 231 | ||||
| -rw-r--r-- | include/asm-mips/sgi/pi1.h | 71 | ||||
| -rw-r--r-- | include/asm-mips/sgi/seeq.h | 21 | ||||
| -rw-r--r-- | include/asm-mips/sgi/sgi.h | 47 | ||||
| -rw-r--r-- | include/asm-mips/sgi/wd.h | 20 |
9 files changed, 0 insertions, 1071 deletions
diff --git a/include/asm-mips/sgi/gio.h b/include/asm-mips/sgi/gio.h deleted file mode 100644 index 889cf02..0000000 --- a/include/asm-mips/sgi/gio.h +++ /dev/null @@ -1,86 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * gio.h: Definitions for SGI GIO bus - * - * Copyright (C) 2002 Ladislav Michl - */ - -#ifndef _SGI_GIO_H -#define _SGI_GIO_H - -/* - * GIO bus addresses - * - * The Indigo and Indy have two GIO bus connectors. Indigo2 (all models) have - * three physical connectors, but only two slots, GFX and EXP0. - * - * There is 10MB of GIO address space for GIO64 slot devices - * slot# slot type address range size - * ----- --------- ----------------------- ----- - * 0 GFX 0x1f000000 - 0x1f3fffff 4MB - * 1 EXP0 0x1f400000 - 0x1f5fffff 2MB - * 2 EXP1 0x1f600000 - 0x1f9fffff 4MB - * - * There are un-slotted devices, HPC, I/O and misc devices, which are grouped - * into the HPC address space. - * - MISC 0x1fb00000 - 0x1fbfffff 1MB - * - * Following space is reserved and unused - * - RESERVED 0x18000000 - 0x1effffff 112MB - * - * GIO bus IDs - * - * Each GIO bus device identifies itself to the system by answering a - * read with an "ID" value. IDs are either 8 or 32 bits long. IDs less - * than 128 are 8 bits long, with the most significant 24 bits read from - * the slot undefined. - * - * 32-bit IDs are divided into - * bits 0:6 the product ID; ranges from 0x00 to 0x7F. - * bit 7 0=GIO Product ID is 8 bits wide - * 1=GIO Product ID is 32 bits wide. - * bits 8:15 manufacturer version for the product. - * bit 16 0=GIO32 and GIO32-bis, 1=GIO64. - * bit 17 0=no ROM present - * 1=ROM present on this board AND next three words - * space define the ROM. - * bits 18:31 up to manufacturer. - * - * IDs above 0x50/0xd0 are of 3rd party boards. - * - * 8-bit IDs - * 0x01 XPI low cost FDDI - * 0x02 GTR TokenRing - * 0x04 Synchronous ISDN - * 0x05 ATM board [*] - * 0x06 Canon Interface - * 0x07 16 bit SCSI Card [*] - * 0x08 JPEG (Double Wide) - * 0x09 JPEG (Single Wide) - * 0x0a XPI mez. FDDI device 0 - * 0x0b XPI mez. FDDI device 1 - * 0x0c SMPTE 259M Video [*] - * 0x0d Babblefish Compression [*] - * 0x0e E-Plex 8-port Ethernet - * 0x30 Lyon Lamb IVAS - * 0xb8 GIO 100BaseTX Fast Ethernet (gfe) - * - * [*] Device provide 32-bit ID. - * - */ - -#define GIO_ID(x) (x & 0x7f) -#define GIO_32BIT_ID 0x80 -#define GIO_REV(x) ((x >> 8) & 0xff) -#define GIO_64BIT_IFACE 0x10000 -#define GIO_ROM_PRESENT 0x20000 -#define GIO_VENDOR_CODE(x) ((x >> 18) & 0x3fff) - -#define GIO_SLOT_GFX_BASE 0x1f000000 -#define GIO_SLOT_EXP0_BASE 0x1f400000 -#define GIO_SLOT_EXP1_BASE 0x1f600000 - -#endif /* _SGI_GIO_H */ diff --git a/include/asm-mips/sgi/hpc3.h b/include/asm-mips/sgi/hpc3.h deleted file mode 100644 index c4729f5..0000000 --- a/include/asm-mips/sgi/hpc3.h +++ /dev/null @@ -1,317 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * hpc3.h: Definitions for SGI HPC3 controller - * - * Copyright (C) 1996 David S. Miller - * Copyright (C) 1998 Ralf Baechle - */ - -#ifndef _SGI_HPC3_H -#define _SGI_HPC3_H - -#include <linux/types.h> -#include <asm/page.h> - -/* An HPC DMA descriptor. */ -struct hpc_dma_desc { - u32 pbuf; /* physical address of data buffer */ - u32 cntinfo; /* counter and info bits */ -#define HPCDMA_EOX 0x80000000 /* last desc in chain for tx */ -#define HPCDMA_EOR 0x80000000 /* last desc in chain for rx */ -#define HPCDMA_EOXP 0x40000000 /* end of packet for tx */ -#define HPCDMA_EORP 0x40000000 /* end of packet for rx */ -#define HPCDMA_XIE 0x20000000 /* irq generated when at end of this desc */ -#define HPCDMA_XIU 0x01000000 /* Tx buffer in use by CPU. */ -#define HPCDMA_EIPC 0x00ff0000 /* SEEQ ethernet special xternal bytecount */ -#define HPCDMA_ETXD 0x00008000 /* set to one by HPC when packet tx'd */ -#define HPCDMA_OWN 0x00004000 /* Denotes ring buffer ownership on rx */ -#define HPCDMA_BCNT 0x00003fff /* size in bytes of this dma buffer */ - - u32 pnext; /* paddr of next hpc_dma_desc if any */ -}; - -/* The set of regs for each HPC3 PBUS DMA channel. */ -struct hpc3_pbus_dmacregs { - volatile u32 pbdma_bptr; /* pbus dma channel buffer ptr */ - volatile u32 pbdma_dptr; /* pbus dma channel desc ptr */ - u32 _unused0[0x1000/4 - 2]; /* padding */ - volatile u32 pbdma_ctrl; /* pbus dma channel control register has - * copletely different meaning for read - * compared with write */ - /* read */ -#define HPC3_PDMACTRL_INT 0x00000001 /* interrupt (cleared after read) */ -#define HPC3_PDMACTRL_ISACT 0x00000002 /* channel active */ - /* write */ -#define HPC3_PDMACTRL_SEL 0x00000002 /* little endian transfer */ -#define HPC3_PDMACTRL_RCV 0x00000004 /* direction is receive */ -#define HPC3_PDMACTRL_FLSH 0x00000008 /* enable flush for receive DMA */ -#define HPC3_PDMACTRL_ACT 0x00000010 /* start dma transfer */ -#define HPC3_PDMACTRL_LD 0x00000020 /* load enable for ACT */ -#define HPC3_PDMACTRL_RT 0x00000040 /* Use realtime GIO bus servicing */ -#define HPC3_PDMACTRL_HW 0x0000ff00 /* DMA High-water mark */ -#define HPC3_PDMACTRL_FB 0x003f0000 /* Ptr to beginning of fifo */ -#define HPC3_PDMACTRL_FE 0x3f000000 /* Ptr to end of fifo */ - - u32 _unused1[0x1000/4 - 1]; /* padding */ -}; - -/* The HPC3 SCSI registers, this does not include external ones. */ -struct hpc3_scsiregs { - volatile u32 cbptr; /* current dma buffer ptr, diagnostic use only */ - volatile u32 ndptr; /* next dma descriptor ptr */ - u32 _unused0[0x1000/4 - 2]; /* padding */ - volatile u32 bcd; /* byte count info */ -#define HPC3_SBCD_BCNTMSK 0x00003fff /* bytes to transfer from/to memory */ -#define HPC3_SBCD_XIE 0x00004000 /* Send IRQ when done with cur buf */ -#define HPC3_SBCD_EOX 0x00008000 /* Indicates this is last buf in chain */ - - volatile u32 ctrl; /* control register */ -#define HPC3_SCTRL_IRQ 0x01 /* IRQ asserted, either dma done or parity */ -#define HPC3_SCTRL_ENDIAN 0x02 /* DMA endian mode, 0=big 1=little */ -#define HPC3_SCTRL_DIR 0x04 /* DMA direction, 1=dev2mem 0=mem2dev */ -#define HPC3_SCTRL_FLUSH 0x08 /* Tells HPC3 to flush scsi fifos */ -#define HPC3_SCTRL_ACTIVE 0x10 /* SCSI DMA channel is active */ -#define HPC3_SCTRL_AMASK 0x20 /* DMA active inhibits PIO */ -#define HPC3_SCTRL_CRESET 0x40 /* Resets dma channel and external controller */ -#define HPC3_SCTRL_PERR 0x80 /* Bad parity on HPC3 iface to scsi controller */ - - volatile u32 gfptr; /* current GIO fifo ptr */ - volatile u32 dfptr; /* current device fifo ptr */ - volatile u32 dconfig; /* DMA configuration register */ -#define HPC3_SDCFG_HCLK 0x00001 /* Enable DMA half clock mode */ -#define HPC3_SDCFG_D1 0x00006 /* Cycles to spend in D1 state */ -#define HPC3_SDCFG_D2 0x00038 /* Cycles to spend in D2 state */ -#define HPC3_SDCFG_D3 0x001c0 /* Cycles to spend in D3 state */ -#define HPC3_SDCFG_HWAT 0x00e00 /* DMA high water mark */ -#define HPC3_SDCFG_HW 0x01000 /* Enable 16-bit halfword DMA accesses to scsi */ -#define HPC3_SDCFG_SWAP 0x02000 /* Byte swap all DMA accesses */ -#define HPC3_SDCFG_EPAR 0x04000 /* Enable parity checking for DMA */ -#define HPC3_SDCFG_POLL 0x08000 /* hd_dreq polarity control */ -#define HPC3_SDCFG_ERLY 0x30000 /* hd_dreq behavior control bits */ - - volatile u32 pconfig; /* PIO configuration register */ -#define HPC3_SPCFG_P3 0x0003 /* Cycles to spend in P3 state */ -#define HPC3_SPCFG_P2W 0x001c /* Cycles to spend in P2 state for writes */ -#define HPC3_SPCFG_P2R 0x01e0 /* Cycles to spend in P2 state for reads */ -#define HPC3_SPCFG_P1 0x0e00 /* Cycles to spend in P1 state */ -#define HPC3_SPCFG_HW 0x1000 /* Enable 16-bit halfword PIO accesses to scsi */ -#define HPC3_SPCFG_SWAP 0x2000 /* Byte swap all PIO accesses */ -#define HPC3_SPCFG_EPAR 0x4000 /* Enable parity checking for PIO */ -#define HPC3_SPCFG_FUJI 0x8000 /* Fujitsu scsi controller mode for faster dma/pio */ - - u32 _unused1[0x1000/4 - 6]; /* padding */ -}; - -/* SEEQ ethernet HPC3 registers, only one seeq per HPC3. */ -struct hpc3_ethregs { - /* Receiver registers. */ - volatile u32 rx_cbptr; /* current dma buffer ptr, diagnostic use only */ - volatile u32 rx_ndptr; /* next dma descriptor ptr */ - u32 _unused0[0x1000/4 - 2]; /* padding */ - volatile u32 rx_bcd; /* byte count info */ -#define HPC3_ERXBCD_BCNTMSK 0x00003fff /* bytes to be sent to memory */ -#define HPC3_ERXBCD_XIE 0x20000000 /* HPC3 interrupts cpu at end of this buf */ -#define HPC3_ERXBCD_EOX 0x80000000 /* flags this as end of descriptor chain */ - - volatile u32 rx_ctrl; /* control register */ -#define HPC3_ERXCTRL_STAT50 0x0000003f /* Receive status reg bits of Seeq8003 */ -#define HPC3_ERXCTRL_STAT6 0x00000040 /* Rdonly irq status */ -#define HPC3_ERXCTRL_STAT7 0x00000080 /* Rdonlt old/new status bit from Seeq */ -#define HPC3_ERXCTRL_ENDIAN 0x00000100 /* Endian for dma channel, little=1 big=0 */ -#define HPC3_ERXCTRL_ACTIVE 0x00000200 /* Tells if DMA transfer is in progress */ -#define HPC3_ERXCTRL_AMASK 0x00000400 /* Tells if ACTIVE inhibits PIO's to hpc3 */ -#define HPC3_ERXCTRL_RBO 0x00000800 /* Receive buffer overflow if set to 1 */ - - volatile u32 rx_gfptr; /* current GIO fifo ptr */ - volatile u32 rx_dfptr; /* current device fifo ptr */ - u32 _unused1; /* padding */ - volatile u32 reset; /* reset register */ -#define HPC3_ERST_CRESET 0x1 /* Reset dma channel and external controller */ -#define HPC3_ERST_CLRIRQ 0x2 /* Clear channel interrupt */ -#define HPC3_ERST_LBACK 0x4 /* Enable diagnostic loopback mode of Seeq8003 */ - - volatile u32 dconfig; /* DMA configuration register */ -#define HPC3_EDCFG_D1 0x0000f /* Cycles to spend in D1 state for PIO */ -#define HPC3_EDCFG_D2 0x000f0 /* Cycles to spend in D2 state for PIO */ -#define HPC3_EDCFG_D3 0x00f00 /* Cycles to spend in D3 state for PIO */ -#define HPC3_EDCFG_WCTRL 0x01000 /* Enable writes of desc into ex ctrl port */ -#define HPC3_EDCFG_FRXDC 0x02000 /* Clear eop stat bits upon rxdc, hw seeq fix */ -#define HPC3_EDCFG_FEOP 0x04000 /* Bad packet marker timeout enable */ -#define HPC3_EDCFG_FIRQ 0x08000 /* Another bad packet timeout enable */ -#define HPC3_EDCFG_PTO 0x30000 /* Programmed timeout value for above two */ - - volatile u32 pconfig; /* PIO configuration register */ -#define HPC3_EPCFG_P1 0x000f /* Cycles to spend in P1 state for PIO */ -#define HPC3_EPCFG_P2 0x00f0 /* Cycles to spend in P2 state for PIO */ -#define HPC3_EPCFG_P3 0x0f00 /* Cycles to spend in P3 state for PIO */ -#define HPC3_EPCFG_TST 0x1000 /* Diagnistic ram test feature bit */ - - u32 _unused2[0x1000/4 - 8]; /* padding */ - - /* Transmitter registers. */ - volatile u32 tx_cbptr; /* current dma buffer ptr, diagnostic use only */ - volatile u32 tx_ndptr; /* next dma descriptor ptr */ - u32 _unused3[0x1000/4 - 2]; /* padding */ - volatile u32 tx_bcd; /* byte count info */ -#define HPC3_ETXBCD_BCNTMSK 0x00003fff /* bytes to be read from memory */ -#define HPC3_ETXBCD_ESAMP 0x10000000 /* if set, too late to add descriptor */ -#define HPC3_ETXBCD_XIE 0x20000000 /* Interrupt cpu at end of cur desc */ -#define HPC3_ETXBCD_EOP 0x40000000 /* Last byte of cur buf is end of packet */ -#define HPC3_ETXBCD_EOX 0x80000000 /* This buf is the end of desc chain */ - - volatile u32 tx_ctrl; /* control register */ -#define HPC3_ETXCTRL_STAT30 0x0000000f /* Rdonly copy of seeq tx stat reg */ -#define HPC3_ETXCTRL_STAT4 0x00000010 /* Indicate late collision occurred */ -#define HPC3_ETXCTRL_STAT75 0x000000e0 /* Rdonly irq status from seeq */ -#define HPC3_ETXCTRL_ENDIAN 0x00000100 /* DMA channel endian mode, 1=little 0=big */ -#define HPC3_ETXCTRL_ACTIVE 0x00000200 /* DMA tx channel is active */ -#define HPC3_ETXCTRL_AMASK 0x00000400 /* Indicates ACTIVE inhibits PIO's */ - - volatile u32 tx_gfptr; /* current GIO fifo ptr */ - volatile u32 tx_dfptr; /* current device fifo ptr */ - u32 _unused4[0x1000/4 - 4]; /* padding */ -}; - -struct hpc3_regs { - /* First regs for the PBUS 8 dma channels. */ - struct hpc3_pbus_dmacregs pbdma[8]; - - /* Now the HPC scsi registers, we get two scsi reg sets. */ - struct hpc3_scsiregs scsi_chan0, scsi_chan1; - - /* The SEEQ hpc3 ethernet dma/control registers. */ - struct hpc3_ethregs ethregs; - - /* Here are where the hpc3 fifo's can be directly accessed - * via PIO accesses. Under normal operation we never stick - * our grubby paws in here so it's just padding. */ - u32 _unused0[0x18000/4]; - - /* HPC3 irq status regs. Due to a peculiar bug you need to - * look at two different register addresses to get at all of - * the status bits. The first reg can only reliably report - * bits 4:0 of the status, and the second reg can only - * reliably report bits 9:5 of the hpc3 irq status. I told - * you it was a peculiar bug. ;-) - */ - volatile u32 istat0; /* Irq status, only bits <4:0> reliable. */ -#define HPC3_ISTAT_PBIMASK 0x0ff /* irq bits for pbus devs 0 --> 7 */ -#define HPC3_ISTAT_SC0MASK 0x100 /* irq bit for scsi channel 0 */ -#define HPC3_ISTAT_SC1MASK 0x200 /* irq bit for scsi channel 1 */ - - volatile u32 gio_misc; /* GIO misc control bits. */ -#define HPC3_GIOMISC_ERTIME 0x1 /* Enable external timer real time. */ -#define HPC3_GIOMISC_DENDIAN 0x2 /* dma descriptor endian, 1=lit 0=big */ - - u32 eeprom; /* EEPROM data reg. */ -#define HPC3_EEPROM_EPROT 0x01 /* Protect register enable */ -#define HPC3_EEPROM_CSEL 0x02 /* Chip select */ -#define HPC3_EEPROM_ECLK 0x04 /* EEPROM clock */ -#define HPC3_EEPROM_DATO 0x08 /* Data out */ -#define HPC3_EEPROM_DATI 0x10 /* Data in */ - - volatile u32 istat1; /* Irq status, only bits <9:5> reliable. */ - volatile u32 bestat; /* Bus error interrupt status reg. */ -#define HPC3_BESTAT_BLMASK 0x000ff /* Bus lane where bad parity occurred */ -#define HPC3_BESTAT_CTYPE 0x00100 /* Bus cycle type, 0=PIO 1=DMA */ -#define HPC3_BESTAT_PIDSHIFT 9 -#define HPC3_BESTAT_PIDMASK 0x3f700 /* DMA channel parity identifier */ - - u32 _unused1[0x14000/4 - 5]; /* padding */ - - /* Now direct PIO per-HPC3 peripheral access to external regs. */ - volatile u32 scsi0_ext[256]; /* SCSI channel 0 external regs */ - u32 _unused2[0x7c00/4]; - volatile u32 scsi1_ext[256]; /* SCSI channel 1 external regs */ - u32 _unused3[0x7c00/4]; - volatile u32 eth_ext[320]; /* Ethernet external registers */ - u32 _unused4[0x3b00/4]; - - /* Per-peripheral device external registers and DMA/PIO control. */ - volatile u32 pbus_extregs[16][256]; - volatile u32 pbus_dmacfg[8][128]; - /* Cycles to spend in D3 for reads */ -#define HPC3_DMACFG_D3R_MASK 0x00000001 -#define HPC3_DMACFG_D3R_SHIFT 0 - /* Cycles to spend in D4 for reads */ -#define HPC3_DMACFG_D4R_MASK 0x0000001e -#define HPC3_DMACFG_D4R_SHIFT 1 - /* Cycles to spend in D5 for reads */ -#define HPC3_DMACFG_D5R_MASK 0x000001e0 -#define HPC3_DMACFG_D5R_SHIFT 5 - /* Cycles to spend in D3 for writes */ -#define HPC3_DMACFG_D3W_MASK 0x00000200 -#define HPC3_DMACFG_D3W_SHIFT 9 - /* Cycles to spend in D4 for writes */ -#define HPC3_DMACFG_D4W_MASK 0x00003c00 -#define HPC3_DMACFG_D4W_SHIFT 10 - /* Cycles to spend in D5 for writes */ -#define HPC3_DMACFG_D5W_MASK 0x0003c000 -#define HPC3_DMACFG_D5W_SHIFT 14 - /* Enable 16-bit DMA access mode */ -#define HPC3_DMACFG_DS16 0x00040000 - /* Places halfwords on high 16 bits of bus */ -#define HPC3_DMACFG_EVENHI 0x00080000 - /* Make this device real time */ -#define HPC3_DMACFG_RTIME 0x00200000 - /* 5 bit burst count for DMA device */ -#define HPC3_DMACFG_BURST_MASK 0x07c00000 -#define HPC3_DMACFG_BURST_SHIFT 22 - /* Use live pbus_dreq unsynchronized signal */ -#define HPC3_DMACFG_DRQLIVE 0x08000000 - volatile u32 pbus_piocfg[16][64]; - /* Cycles to spend in P2 state for reads */ -#define HPC3_PIOCFG_P2R_MASK 0x00001 -#define HPC3_PIOCFG_P2R_SHIFT 0 - /* Cycles to spend in P3 state for reads */ -#define HPC3_PIOCFG_P3R_MASK 0x0001e -#define HPC3_PIOCFG_P3R_SHIFT 1 - /* Cycles to spend in P4 state for reads */ -#define HPC3_PIOCFG_P4R_MASK 0x001e0 -#define HPC3_PIOCFG_P4R_SHIFT 5 - /* Cycles to spend in P2 state for writes */ -#define HPC3_PIOCFG_P2W_MASK 0x00200 -#define HPC3_PIOCFG_P2W_SHIFT 9 - /* Cycles to spend in P3 state for writes */ -#define HPC3_PIOCFG_P3W_MASK 0x03c00 -#define HPC3_PIOCFG_P3W_SHIFT 10 - /* Cycles to spend in P4 state for writes */ -#define HPC3_PIOCFG_P4W_MASK 0x3c000 -#define HPC3_PIOCFG_P4W_SHIFT 14 - /* Enable 16-bit PIO accesses */ -#define HPC3_PIOCFG_DS16 0x40000 - /* Place even address bits in bits <15:8> */ -#define HPC3_PIOCFG_EVENHI 0x80000 - - /* PBUS PROM control regs. */ - volatile u32 pbus_promwe; /* PROM write enable register */ -#define HPC3_PROM_WENAB 0x1 /* Enable writes to the PROM */ - - u32 _unused5[0x0800/4 - 1]; - volatile u32 pbus_promswap; /* Chip select swap reg */ -#define HPC3_PROM_SWAP 0x1 /* invert GIO addr bit to select prom0 or prom1 */ - - u32 _unused6[0x0800/4 - 1]; - volatile u32 pbus_gout; /* PROM general purpose output reg */ -#define HPC3_PROM_STAT 0x1 /* General purpose status bit in gout */ - - u32 _unused7[0x1000/4 - 1]; - volatile u32 rtcregs[14]; /* Dallas clock registers */ - u32 _unused8[50]; - volatile u32 bbram[8192-50-14]; /* Battery backed ram */ -}; - -/* - * It is possible to have two HPC3's within the address space on - * one machine, though only having one is more likely on an Indy. - */ -extern struct hpc3_regs *hpc3c0, *hpc3c1; -#define HPC3_CHIP0_BASE 0x1fb80000 /* physical */ -#define HPC3_CHIP1_BASE 0x1fb00000 /* physical */ - -extern void sgihpc_init(void); - -#endif /* _SGI_HPC3_H */ diff --git a/include/asm-mips/sgi/ioc.h b/include/asm-mips/sgi/ioc.h deleted file mode 100644 index 343ed15..0000000 --- a/include/asm-mips/sgi/ioc.h +++ /dev/null @@ -1,200 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * ioc.h: Definitions for SGI I/O Controller - * - * Copyright (C) 1996 David S. Miller - * Copyright (C) 1997, 1998, 1999, 2000 Ralf Baechle - * Copyright (C) 2001, 2003 Ladislav Michl - */ - -#ifndef _SGI_IOC_H -#define _SGI_IOC_H - -#include <linux/types.h> -#include <asm/sgi/pi1.h> - -/* - * All registers are 8-bit wide alligned on 32-bit boundary. Bad things - * happen if you try word access them. You have been warned. - */ - -struct sgioc_uart_regs { - u8 _ctrl1[3]; - volatile u8 ctrl1; - u8 _data1[3]; - volatile u8 data1; - u8 _ctrl2[3]; - volatile u8 ctrl2; - u8 _data2[3]; - volatile u8 data2; -}; - -struct sgioc_keyb_regs { - u8 _data[3]; - volatile u8 data; - u8 _command[3]; - volatile u8 command; -}; - -struct sgint_regs { - u8 _istat0[3]; - volatile u8 istat0; /* Interrupt status zero */ -#define SGINT_ISTAT0_FFULL 0x01 -#define SGINT_ISTAT0_SCSI0 0x02 -#define SGINT_ISTAT0_SCSI1 0x04 -#define SGINT_ISTAT0_ENET 0x08 -#define SGINT_ISTAT0_GFXDMA 0x10 -#define SGINT_ISTAT0_PPORT 0x20 -#define SGINT_ISTAT0_HPC2 0x40 -#define SGINT_ISTAT0_LIO2 0x80 - u8 _imask0[3]; - volatile u8 imask0; /* Interrupt mask zero */ - u8 _istat1[3]; - volatile u8 istat1; /* Interrupt status one */ -#define SGINT_ISTAT1_ISDNI 0x01 -#define SGINT_ISTAT1_PWR 0x02 -#define SGINT_ISTAT1_ISDNH 0x04 -#define SGINT_ISTAT1_LIO3 0x08 -#define SGINT_ISTAT1_HPC3 0x10 -#define SGINT_ISTAT1_AFAIL 0x20 -#define SGINT_ISTAT1_VIDEO 0x40 -#define SGINT_ISTAT1_GIO2 0x80 - u8 _imask1[3]; - volatile u8 imask1; /* Interrupt mask one */ - u8 _vmeistat[3]; - volatile u8 vmeistat; /* VME interrupt status */ - u8 _cmeimask0[3]; - volatile u8 cmeimask0; /* VME interrupt mask zero */ - u8 _cmeimask1[3]; - volatile u8 cmeimask1; /* VME interrupt mask one */ - u8 _cmepol[3]; - volatile u8 cmepol; /* VME polarity */ - u8 _tclear[3]; - volatile u8 tclear; - u8 _errstat[3]; - volatile u8 errstat; /* Error status reg, reserved on INT2 */ - u32 _unused0[2]; - u8 _tcnt0[3]; - volatile u8 tcnt0; /* counter 0 */ - u8 _tcnt1[3]; - volatile u8 tcnt1; /* counter 1 */ - u8 _tcnt2[3]; - volatile u8 tcnt2; /* counter 2 */ - u8 _tcword[3]; - volatile u8 tcword; /* control word */ -#define SGINT_TCWORD_BCD 0x01 /* Use BCD mode for counters */ -#define SGINT_TCWORD_MMASK 0x0e /* Mode bitmask. */ -#define SGINT_TCWORD_MITC 0x00 /* IRQ on terminal count (doesn't work) */ -#define SGINT_TCWORD_MOS 0x02 /* One-shot IRQ mode. */ -#define SGINT_TCWORD_MRGEN 0x04 /* Normal rate generation */ -#define SGINT_TCWORD_MSWGEN 0x06 /* Square wave generator mode */ -#define SGINT_TCWORD_MSWST 0x08 /* Software strobe */ -#define SGINT_TCWORD_MHWST 0x0a /* Hardware strobe */ -#define SGINT_TCWORD_CMASK 0x30 /* Command mask */ -#define SGINT_TCWORD_CLAT 0x00 /* Latch command */ -#define SGINT_TCWORD_CLSB 0x10 /* LSB read/write */ -#define SGINT_TCWORD_CMSB 0x20 /* MSB read/write */ -#define SGINT_TCWORD_CALL 0x30 /* Full counter read/write */ -#define SGINT_TCWORD_CNT0 0x00 /* Select counter zero */ -#define SGINT_TCWORD_CNT1 0x40 /* Select counter one */ -#define SGINT_TCWORD_CNT2 0x80 /* Select counter two */ -#define SGINT_TCWORD_CRBCK 0xc0 /* Readback command */ -}; - -/* - * The timer is the good old 8254. Unlike in PCs it's clocked at exactly 1MHz - */ -#define SGINT_TIMER_CLOCK 1000000 - -/* - * This is the constant we're using for calibrating the counter. - */ -#define SGINT_TCSAMP_COUNTER ((SGINT_TIMER_CLOCK / HZ) + 255) - -/* We need software copies of these because they are write only. */ -extern u8 sgi_ioc_reset, sgi_ioc_write; - -struct sgioc_regs { - struct pi1_regs pport; - u32 _unused0[2]; - struct sgioc_uart_regs uart; - struct sgioc_keyb_regs kbdmouse; - u8 _gcsel[3]; - volatile u8 gcsel; - u8 _genctrl[3]; - volatile u8 genctrl; - u8 _panel[3]; - volatile u8 panel; -#define SGIOC_PANEL_POWERON 0x01 -#define SGIOC_PANEL_POWERINTR 0x02 -#define SGIOC_PANEL_VOLDNINTR 0x10 -#define SGIOC_PANEL_VOLDNHOLD 0x20 -#define SGIOC_PANEL_VOLUPINTR 0x40 -#define SGIOC_PANEL_VOLUPHOLD 0x80 - u32 _unused1; - u8 _sysid[3]; - volatile u8 sysid; -#define SGIOC_SYSID_FULLHOUSE 0x01 -#define SGIOC_SYSID_BOARDREV(x) (((x) & 0x1e) >> 1) -#define SGIOC_SYSID_CHIPREV(x) (((x) & 0xe0) >> 5) - u32 _unused2; - u8 _read[3]; - volatile u8 read; - u32 _unused3; - u8 _dmasel[3]; - volatile u8 dmasel; -#define SGIOC_DMASEL_SCLK10MHZ 0x00 /* use 10MHZ serial clock */ -#define SGIOC_DMASEL_ISDNB 0x01 /* enable isdn B */ -#define SGIOC_DMASEL_ISDNA 0x02 /* enable isdn A */ -#define SGIOC_DMASEL_PPORT 0x04 /* use parallel DMA */ -#define SGIOC_DMASEL_SCLK667MHZ 0x10 /* use 6.67MHZ serial clock */ -#define SGIOC_DMASEL_SCLKEXT 0x20 /* use external serial clock */ - u32 _unused4; - u8 _reset[3]; - volatile u8 reset; -#define SGIOC_RESET_PPORT 0x01 /* 0=parport reset, 1=nornal */ -#define SGIOC_RESET_KBDMOUSE 0x02 /* 0=kbdmouse reset, 1=normal */ -#define SGIOC_RESET_EISA 0x04 /* 0=eisa reset, 1=normal */ -#define SGIOC_RESET_ISDN 0x08 /* 0=isdn reset, 1=normal */ -#define SGIOC_RESET_LC0OFF 0x10 /* guiness: turn led off (red, else green) */ -#define SGIOC_RESET_LC1OFF 0x20 /* guiness: turn led off (green, else amber) */ - u32 _unused5; - u8 _write[3]; - volatile u8 write; -#define SGIOC_WRITE_NTHRESH 0x01 /* use 4.5db threshhold */ -#define SGIOC_WRITE_TPSPEED 0x02 /* use 100ohm TP speed */ -#define SGIOC_WRITE_EPSEL 0x04 /* force cable mode: 1=AUI 0=TP */ -#define SGIOC_WRITE_EASEL 0x08 /* 1=autoselect 0=manual cable selection */ -#define SGIOC_WRITE_U1AMODE 0x10 /* 1=PC 0=MAC UART mode */ -#define SGIOC_WRITE_U0AMODE 0x20 /* 1=PC 0=MAC UART mode */ -#define SGIOC_WRITE_MLO 0x40 /* 1=4.75V 0=+5V */ -#define SGIOC_WRITE_MHI 0x80 /* 1=5.25V 0=+5V */ - u32 _unused6; - struct sgint_regs int3; - u32 _unused7[16]; - volatile u32 extio; /* FullHouse only */ -#define EXTIO_S0_IRQ_3 0x8000 /* S0: vid.vsync */ -#define EXTIO_S0_IRQ_2 0x4000 /* S0: gfx.fifofull */ -#define EXTIO_S0_IRQ_1 0x2000 /* S0: gfx.int */ -#define EXTIO_S0_RETRACE 0x1000 -#define EXTIO_SG_IRQ_3 0x0800 /* SG: vid.vsync */ -#define EXTIO_SG_IRQ_2 0x0400 /* SG: gfx.fifofull */ -#define EXTIO_SG_IRQ_1 0x0200 /* SG: gfx.int */ -#define EXTIO_SG_RETRACE 0x0100 -#define EXTIO_GIO_33MHZ 0x0080 -#define EXTIO_EISA_BUSERR 0x0040 -#define EXTIO_MC_BUSERR 0x0020 -#define EXTIO_HPC3_BUSERR 0x0010 -#define EXTIO_S0_STAT_1 0x0008 -#define EXTIO_S0_STAT_0 0x0004 -#define EXTIO_SG_STAT_1 0x0002 -#define EXTIO_SG_STAT_0 0x0001 -}; - -extern struct sgioc_regs *sgioc; -extern struct sgint_regs *sgint; - -#endif diff --git a/include/asm-mips/sgi/ip22.h b/include/asm-mips/sgi/ip22.h deleted file mode 100644 index c0501f9..0000000 --- a/include/asm-mips/sgi/ip22.h +++ /dev/null @@ -1,78 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * ip22.h: Definitions for SGI IP22 machines - * - * Copyright (C) 1996 David S. Miller - * Copyright (C) 1997, 1998, 1999, 2000 Ralf Baechle - */ - -#ifndef _SGI_IP22_H -#define _SGI_IP22_H - -/* - * These are the virtual IRQ numbers, we divide all IRQ's into - * 'spaces', the 'space' determines where and how to enable/disable - * that particular IRQ on an SGI machine. HPC DMA and MC DMA interrupts - * are not supported this way. Driver is supposed to allocate HPC/MC - * interrupt as shareable and then look to proper status bit (see - * HAL2 driver). This will prevent many complications, trust me ;-) - */ - -#include <irq.h> -#include <asm/sgi/ioc.h> - -#define SGINT_EISA 0 /* 16 EISA irq levels (Indigo2) */ -#define SGINT_CPU MIPS_CPU_IRQ_BASE /* MIPS CPU define 8 interrupt sources */ -#define SGINT_LOCAL0 (SGINT_CPU+8) /* 8 local0 irq levels */ -#define SGINT_LOCAL1 (SGINT_CPU+16) /* 8 local1 irq levels */ -#define SGINT_LOCAL2 (SGINT_CPU+24) /* 8 local2 vectored irq levels */ -#define SGINT_LOCAL3 (SGINT_CPU+32) /* 8 local3 vectored irq levels */ -#define SGINT_END (SGINT_CPU+40) /* End of 'spaces' */ - -/* - * Individual interrupt definitions for the Indy and Indigo2 - */ - -#define SGI_SOFT_0_IRQ SGINT_CPU + 0 -#define SGI_SOFT_1_IRQ SGINT_CPU + 1 -#define SGI_LOCAL_0_IRQ SGINT_CPU + 2 -#define SGI_LOCAL_1_IRQ SGINT_CPU + 3 -#define SGI_8254_0_IRQ SGINT_CPU + 4 -#define SGI_8254_1_IRQ SGINT_CPU + 5 -#define SGI_BUSERR_IRQ SGINT_CPU + 6 -#define SGI_TIMER_IRQ SGINT_CPU + 7 - -#define SGI_FIFO_IRQ SGINT_LOCAL0 + 0 /* FIFO full */ -#define SGI_GIO_0_IRQ SGI_FIFO_IRQ /* GIO-0 */ -#define SGI_WD93_0_IRQ SGINT_LOCAL0 + 1 /* 1st onboard WD93 */ -#define SGI_WD93_1_IRQ SGINT_LOCAL0 + 2 /* 2nd onboard WD93 */ -#define SGI_ENET_IRQ SGINT_LOCAL0 + 3 /* onboard ethernet */ -#define SGI_MCDMA_IRQ SGINT_LOCAL0 + 4 /* MC DMA done */ -#define SGI_PARPORT_IRQ SGINT_LOCAL0 + 5 /* Parallel port */ -#define SGI_GIO_1_IRQ SGINT_LOCAL0 + 6 /* GE / GIO-1 / 2nd-HPC */ -#define SGI_MAP_0_IRQ SGINT_LOCAL0 + 7 /* Mappable interrupt 0 */ - -#define SGI_GPL0_IRQ SGINT_LOCAL1 + 0 /* General Purpose LOCAL1_N<0> */ -#define SGI_PANEL_IRQ SGINT_LOCAL1 + 1 /* front panel */ -#define SGI_GPL2_IRQ SGINT_LOCAL1 + 2 /* General Purpose LOCAL1_N<2> */ -#define SGI_MAP_1_IRQ SGINT_LOCAL1 + 3 /* Mappable interrupt 1 */ -#define SGI_HPCDMA_IRQ SGINT_LOCAL1 + 4 /* HPC DMA done */ -#define SGI_ACFAIL_IRQ SGINT_LOCAL1 + 5 /* AC fail */ -#define SGI_VINO_IRQ SGINT_LOCAL1 + 6 /* Indy VINO */ -#define SGI_GIO_2_IRQ SGINT_LOCAL1 + 7 /* Vert retrace / GIO-2 */ - -/* Mapped interrupts. These interrupts may be mapped to either 0, or 1 */ -#define SGI_VERT_IRQ SGINT_LOCAL2 + 0 /* INT3: newport vertical status */ -#define SGI_EISA_IRQ SGINT_LOCAL2 + 3 /* EISA interrupts */ -#define SGI_KEYBD_IRQ SGINT_LOCAL2 + 4 /* keyboard */ -#define SGI_SERIAL_IRQ SGINT_LOCAL2 + 5 /* onboard serial */ - -#define ip22_is_fullhouse() (sgioc->sysid & SGIOC_SYSID_FULLHOUSE) - -extern unsigned short ip22_eeprom_read(unsigned int *ctrl, int reg); -extern unsigned short ip22_nvram_read(int reg); - -#endif diff --git a/include/asm-mips/sgi/mc.h b/include/asm-mips/sgi/mc.h deleted file mode 100644 index 1576c23..0000000 --- a/include/asm-mips/sgi/mc.h +++ /dev/null @@ -1,231 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * mc.h: Definitions for SGI Memory Controller - * - * Copyright (C) 1996 David S. Miller - * Copyright (C) 1999 Ralf Baechle - * Copyright (C) 1999 Silicon Graphics, Inc. - */ - -#ifndef _SGI_MC_H -#define _SGI_MC_H - -struct sgimc_regs { - u32 _unused0; - volatile u32 cpuctrl0; /* CPU control register 0, readwrite */ -#define SGIMC_CCTRL0_REFS 0x0000000f /* REFS mask */ -#define SGIMC_CCTRL0_EREFRESH 0x00000010 /* Memory refresh enable */ -#define SGIMC_CCTRL0_EPERRGIO 0x00000020 /* GIO parity error enable */ -#define SGIMC_CCTRL0_EPERRMEM 0x00000040 /* Main mem parity error enable */ -#define SGIMC_CCTRL0_EPERRCPU 0x00000080 /* CPU bus parity error enable */ -#define SGIMC_CCTRL0_WDOG 0x00000100 /* Watchdog timer enable */ -#define SGIMC_CCTRL0_SYSINIT 0x00000200 /* System init bit */ -#define SGIMC_CCTRL0_GFXRESET 0x00000400 /* Graphics interface reset */ -#define SGIMC_CCTRL0_EISALOCK 0x00000800 /* Lock CPU from memory for EISA */ -#define SGIMC_CCTRL0_EPERRSCMD 0x00001000 /* SysCMD bus parity error enable */ -#define SGIMC_CCTRL0_IENAB 0x00002000 /* Allow interrupts from MC */ -#define SGIMC_CCTRL0_ESNOOP 0x00004000 /* Snooping I/O enable */ -#define SGIMC_CCTRL0_EPROMWR 0x00008000 /* Prom writes from cpu enable */ -#define SGIMC_CCTRL0_WRESETPMEM 0x00010000 /* Perform warm reset, preserves mem */ -#define SGIMC_CCTRL0_LENDIAN 0x00020000 /* Put MC in little-endian mode */ -#define SGIMC_CCTRL0_WRESETDMEM 0x00040000 /* Warm reset, destroys mem contents */ -#define SGIMC_CCTRL0_CMEMBADPAR 0x02000000 /* Generate bad perr from cpu to mem */ -#define SGIMC_CCTRL0_R4KNOCHKPARR 0x04000000 /* Don't chk parity on mem data reads */ -#define SGIMC_CCTRL0_GIOBTOB 0x08000000 /* Allow GIO back to back writes */ - u32 _unused1; - volatile u32 cpuctrl1; /* CPU control register 1, readwrite */ -#define SGIMC_CCTRL1_EGIOTIMEO 0x00000010 /* GIO bus timeout enable */ -#define SGIMC_CCTRL1_FIXEDEHPC 0x00001000 /* Fixed HPC endianness */ -#define SGIMC_CCTRL1_LITTLEHPC 0x00002000 /* Little endian HPC */ -#define SGIMC_CCTRL1_FIXEDEEXP0 0x00004000 /* Fixed EXP0 endianness */ -#define SGIMC_CCTRL1_LITTLEEXP0 0x00008000 /* Little endian EXP0 */ -#define SGIMC_CCTRL1_FIXEDEEXP1 0x00010000 /* Fixed EXP1 endianness */ -#define SGIMC_CCTRL1_LITTLEEXP1 0x00020000 /* Little endian EXP1 */ - - u32 _unused2; - volatile u32 watchdogt; /* Watchdog reg rdonly, write clears */ - - u32 _unused3; - volatile u32 systemid; /* MC system ID register, readonly */ -#define SGIMC_SYSID_MASKREV 0x0000000f /* Revision of MC controller */ -#define SGIMC_SYSID_EPRESENT 0x00000010 /* Indicates presence of EISA bus */ - - u32 _unused4[3]; - volatile u32 divider; /* Divider reg for RPSS */ - - u32 _unused5; - u32 eeprom; /* EEPROM byte reg for r4k */ -#define SGIMC_EEPROM_PRE 0x00000001 /* eeprom chip PRE pin assertion */ -#define SGIMC_EEPROM_CSEL 0x00000002 /* Active high, eeprom chip select */ -#define SGIMC_EEPROM_SECLOCK 0x00000004 /* EEPROM serial clock */ -#define SGIMC_EEPROM_SDATAO 0x00000008 /* Serial EEPROM data-out */ -#define SGIMC_EEPROM_SDATAI 0x00000010 /* Serial EEPROM data-in */ - - u32 _unused6[3]; - volatile u32 rcntpre; /* Preload refresh counter */ - - u32 _unused7; - volatile u32 rcounter; /* Readonly refresh counter */ - - u32 _unused8[13]; - volatile u32 giopar; /* Parameter word for GIO64 */ -#define SGIMC_GIOPAR_HPC64 0x00000001 /* HPC talks to GIO using 64-bits */ -#define SGIMC_GIOPAR_GFX64 0x00000002 /* GFX talks to GIO using 64-bits */ -#define SGIMC_GIOPAR_EXP064 0x00000004 /* EXP(slot0) talks using 64-bits */ -#define SGIMC_GIOPAR_EXP164 0x00000008 /* EXP(slot1) talks using 64-bits */ -#define SGIMC_GIOPAR_EISA64 0x00000010 /* EISA bus talks 64-bits to GIO */ -#define SGIMC_GIOPAR_HPC264 0x00000020 /* 2nd HPX talks 64-bits to GIO */ -#define SGIMC_GIOPAR_RTIMEGFX 0x00000040 /* GFX device has realtime attr */ -#define SGIMC_GIOPAR_RTIMEEXP0 0x00000080 /* EXP(slot0) has realtime attr */ -#define SGIMC_GIOPAR_RTIMEEXP1 0x00000100 /* EXP(slot1) has realtime attr */ -#define SGIMC_GIOPAR_MASTEREISA 0x00000200 /* EISA bus can act as bus master */ -#define SGIMC_GIOPAR_ONEBUS 0x00000400 /* Exists one GIO64 pipelined bus */ -#define SGIMC_GIOPAR_MASTERGFX 0x00000800 /* GFX can act as a bus master */ -#define SGIMC_GIOPAR_MASTEREXP0 0x00001000 /* EXP(slot0) can bus master */ -#define SGIMC_GIOPAR_MASTEREXP1 0x00002000 /* EXP(slot1) can bus master */ -#define SGIMC_GIOPAR_PLINEEXP0 0x00004000 /* EXP(slot0) has pipeline attr */ -#define SGIMC_GIOPAR_PLINEEXP1 0x00008000 /* EXP(slot1) has pipeline attr */ - - u32 _unused9; - volatile u32 cputp; /* CPU bus arb time period */ - - u32 _unused10[3]; - volatile u32 lbursttp; /* Time period for long bursts */ - - /* MC chip can drive up to 4 bank 4 SIMMs each. All SIMMs in bank must - * be the same size. The size encoding for supported SIMMs is bellow */ - u32 _unused11[9]; - volatile u32 mconfig0; /* Memory config register zero */ - u32 _unused12; - volatile u32 mconfig1; /* Memory config register one */ -#define SGIMC_MCONFIG_BASEADDR 0x000000ff /* Base address of bank*/ -#define SGIMC_MCONFIG_RMASK 0x00001f00 /* Ram config bitmask */ -#define SGIMC_MCONFIG_BVALID 0x00002000 /* Bank is valid */ -#define SGIMC_MCONFIG_SBANKS 0x00004000 /* Number of subbanks */ - - u32 _unused13; - volatile u32 cmacc; /* Mem access config for CPU */ - u32 _unused14; - volatile u32 gmacc; /* Mem access config for GIO */ - - /* This define applies to both cmacc and gmacc registers above. */ -#define SGIMC_MACC_ALIASBIG 0x20000000 /* 512MB home for alias */ - - /* Error address/status regs from GIO and CPU perspectives. */ - u32 _unused15; - volatile u32 cerr; /* Error address reg for CPU */ - u32 _unused16; - volatile u32 cstat; /* Status reg for CPU */ -#define SGIMC_CSTAT_RD 0x00000100 /* read parity error */ -#define SGIMC_CSTAT_PAR 0x00000200 /* CPU parity error */ -#define SGIMC_CSTAT_ADDR 0x00000400 /* memory bus error bad addr */ -#define SGIMC_CSTAT_SYSAD_PAR 0x00000800 /* sysad parity error */ -#define SGIMC_CSTAT_SYSCMD_PAR 0x00001000 /* syscmd parity error */ -#define SGIMC_CSTAT_BAD_DATA 0x00002000 /* bad data identifier */ -#define SGIMC_CSTAT_PAR_MASK 0x00001f00 /* parity error mask */ -#define SGIMC_CSTAT_RD_PAR (SGIMC_CSTAT_RD | SGIMC_CSTAT_PAR) - - u32 _unused17; - volatile u32 gerr; /* Error address reg for GIO */ - u32 _unused18; - volatile u32 gstat; /* Status reg for GIO */ -#define SGIMC_GSTAT_RD 0x00000100 /* read parity error */ -#define SGIMC_GSTAT_WR 0x00000200 /* write parity error */ -#define SGIMC_GSTAT_TIME 0x00000400 /* GIO bus timed out */ -#define SGIMC_GSTAT_PROM 0x00000800 /* write to PROM when PROM_EN not set */ -#define SGIMC_GSTAT_ADDR 0x00001000 /* parity error on addr cycle */ -#define SGIMC_GSTAT_BC 0x00002000 /* parity error on byte count cycle */ -#define SGIMC_GSTAT_PIO_RD 0x00004000 /* read data parity on pio */ -#define SGIMC_GSTAT_PIO_WR 0x00008000 /* write data parity on pio */ - - /* Special hard bus locking registers. */ - u32 _unused19; - volatile u32 syssembit; /* Uni-bit system semaphore */ - u32 _unused20; - volatile u32 mlock; /* Global GIO memory access lock */ - u32 _unused21; - volatile u32 elock; /* Locks EISA from GIO accesses */ - - /* GIO dma control registers. */ - u32 _unused22[15]; - volatile u32 gio_dma_trans; /* DMA mask to translation GIO addrs */ - u32 _unused23; - volatile u32 gio_dma_sbits; /* DMA GIO addr substitution bits */ - u32 _unused24; - volatile u32 dma_intr_cause; /* DMA IRQ cause indicator bits */ - u32 _unused25; - volatile u32 dma_ctrl; /* Main DMA control reg */ - - /* DMA TLB entry 0 */ - u32 _unused26[5]; - volatile u32 dtlb_hi0; - u32 _unused27; - volatile u32 dtlb_lo0; - - /* DMA TLB entry 1 */ - u32 _unused28; - volatile u32 dtlb_hi1; - u32 _unused29; - volatile u32 dtlb_lo1; - - /* DMA TLB entry 2 */ - u32 _unused30; - volatile u32 dtlb_hi2; - u32 _unused31; - volatile u32 dtlb_lo2; - - /* DMA TLB entry 3 */ - u32 _unused32; - volatile u32 dtlb_hi3; - u32 _unused33; - volatile u32 dtlb_lo3; - - u32 _unused34[0x0392]; - - u32 _unused35; - volatile u32 rpsscounter; /* Chirps at 100ns */ - - u32 _unused36[0x1000/4-2*4]; - - u32 _unused37; - volatile u32 maddronly; /* Address DMA goes at */ - u32 _unused38; - volatile u32 maddrpdeflts; /* Same as above, plus set defaults */ - u32 _unused39; - volatile u32 dmasz; /* DMA count */ - u32 _unused40; - volatile u32 ssize; /* DMA stride size */ - u32 _unused41; - volatile u32 gmaddronly; /* Set GIO DMA but don't start trans */ - u32 _unused42; - volatile u32 dmaddnpgo; /* Set GIO DMA addr + start transfer */ - u32 _unused43; - volatile u32 dmamode; /* DMA mode config bit settings */ - u32 _unused44; - volatile u32 dmaccount; /* Zoom and byte count for DMA */ - u32 _unused45; - volatile u32 dmastart; /* Pedal to the metal. */ - u32 _unused46; - volatile u32 dmarunning; /* DMA op is in progress */ - u32 _unused47; - volatile u32 maddrdefstart; /* Set dma addr, defaults, and kick it */ -}; - -extern struct sgimc_regs *sgimc; -#define SGIMC_BASE 0x1fa00000 /* physical */ - -/* Base location of the two ram banks found in IP2[0268] machines. */ -#define SGIMC_SEG0_BADDR 0x08000000 -#define SGIMC_SEG1_BADDR 0x20000000 - -/* Maximum size of the above banks are per machine. */ -#define SGIMC_SEG0_SIZE_ALL 0x10000000 /* 256MB */ -#define SGIMC_SEG1_SIZE_IP20_IP22 0x08000000 /* 128MB */ -#define SGIMC_SEG1_SIZE_IP26_IP28 0x20000000 /* 512MB */ - -extern void sgimc_init(void); - -#endif /* _SGI_MC_H */ diff --git a/include/asm-mips/sgi/pi1.h b/include/asm-mips/sgi/pi1.h deleted file mode 100644 index c950691..0000000 --- a/include/asm-mips/sgi/pi1.h +++ /dev/null @@ -1,71 +0,0 @@ -/* - * pi1.h: Definitions for SGI PI1 parallel port - */ - -#ifndef _SGI_PI1_H -#define _SGI_PI1_H - -struct pi1_regs { - u8 _data[3]; - volatile u8 data; - u8 _ctrl[3]; - volatile u8 ctrl; -#define PI1_CTRL_STROBE_N 0x01 -#define PI1_CTRL_AFD_N 0x02 -#define PI1_CTRL_INIT_N 0x04 -#define PI1_CTRL_SLIN_N 0x08 -#define PI1_CTRL_IRQ_ENA 0x10 -#define PI1_CTRL_DIR 0x20 -#define PI1_CTRL_SEL 0x40 - u8 _status[3]; - volatile u8 status; -#define PI1_STAT_DEVID 0x03 /* bits 0-1 */ -#define PI1_STAT_NOINK 0x04 /* SGI MODE only */ -#define PI1_STAT_ERROR 0x08 -#define PI1_STAT_ONLINE 0x10 -#define PI1_STAT_PE 0x20 -#define PI1_STAT_ACK 0x40 -#define PI1_STAT_BUSY 0x80 - u8 _dmactrl[3]; - volatile u8 dmactrl; -#define PI1_DMACTRL_FIFO_EMPTY 0x01 /* fifo empty R/O */ -#define PI1_DMACTRL_ABORT 0x02 /* reset DMA and internal fifo W/O */ -#define PI1_DMACTRL_STDMODE 0x00 /* bits 2-3 */ -#define PI1_DMACTRL_SGIMODE 0x04 /* bits 2-3 */ -#define PI1_DMACTRL_RICOHMODE 0x08 /* bits 2-3 */ -#define PI1_DMACTRL_HPMODE 0x0c /* bits 2-3 */ -#define PI1_DMACTRL_BLKMODE 0x10 /* block mode */ -#define PI1_DMACTRL_FIFO_CLEAR 0x20 /* clear fifo W/O */ -#define PI1_DMACTRL_READ 0x40 /* read */ -#define PI1_DMACTRL_RUN 0x80 /* pedal to the metal */ - u8 _intstat[3]; - volatile u8 intstat; -#define PI1_INTSTAT_ACK 0x04 -#define PI1_INTSTAT_FEMPTY 0x08 -#define PI1_INTSTAT_NOINK 0x10 -#define PI1_INTSTAT_ONLINE 0x20 -#define PI1_INTSTAT_ERR 0x40 -#define PI1_INTSTAT_PE 0x80 - u8 _intmask[3]; - volatile u8 intmask; /* enabled low, reset high*/ -#define PI1_INTMASK_ACK 0x04 -#define PI1_INTMASK_FIFO_EMPTY 0x08 -#define PI1_INTMASK_NOINK 0x10 -#define PI1_INTMASK_ONLINE 0x20 -#define PI1_INTMASK_ERR 0x40 -#define PI1_INTMASK_PE 0x80 - u8 _timer1[3]; - volatile u8 timer1; -#define PI1_TIME1 0x27 - u8 _timer2[3]; - volatile u8 timer2; -#define PI1_TIME2 0x13 - u8 _timer3[3]; - volatile u8 timer3; -#define PI1_TIME3 0x10 - u8 _timer4[3]; - volatile u8 timer4; -#define PI1_TIME4 0x00 -}; - -#endif diff --git a/include/asm-mips/sgi/seeq.h b/include/asm-mips/sgi/seeq.h deleted file mode 100644 index af0ffd7..0000000 --- a/include/asm-mips/sgi/seeq.h +++ /dev/null @@ -1,21 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Copyright (C) 2007 by Ralf Baechle - */ -#ifndef __ASM_SGI_SEEQ_H -#define __ASM_SGI_SEEQ_H - -#include <linux/if_ether.h> - -#include <asm/sgi/hpc3.h> - -struct sgiseeq_platform_data { - struct hpc3_regs *hpc; - unsigned int irq; - unsigned char mac[ETH_ALEN]; -}; - -#endif /* __ASM_SGI_SEEQ_H */ diff --git a/include/asm-mips/sgi/sgi.h b/include/asm-mips/sgi/sgi.h deleted file mode 100644 index 645cea7..0000000 --- a/include/asm-mips/sgi/sgi.h +++ /dev/null @@ -1,47 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * sgi.h: Definitions specific to SGI machines. - * - * Copyright (C) 1996 David S. Miller (dm@sgi.com) - */ -#ifndef _ASM_SGI_SGI_H -#define _ASM_SGI_SGI_H - -/* UP=UniProcessor MP=MultiProcessor(capable) */ -enum sgi_mach { - ip4, /* R2k UP */ - ip5, /* R2k MP */ - ip6, /* R3k UP */ - ip7, /* R3k MP */ - ip9, /* R3k UP */ - ip12, /* R3kA UP, Indigo */ - ip15, /* R3kA MP */ - ip17, /* R4K UP */ - ip19, /* R4K MP */ - ip20, /* R4K UP, Indigo */ - ip21, /* TFP MP */ - ip22, /* R4x00 UP, Indigo2 */ - ip25, /* R10k MP */ - ip26, /* TFP UP, Indigo2 */ - ip27, /* R10k MP, R12k MP, Origin */ - ip28, /* R10k UP, Indigo2 */ - ip30, /* Octane */ - ip32, /* O2 */ -}; - -extern enum sgi_mach sgimach; -extern void sgi_sysinit(void); - -/* Many I/O space registers are byte sized and are contained within - * one byte per word, specifically the MSB, this macro helps out. - */ -#ifdef __MIPSEL__ -#define SGI_MSB(regaddr) (regaddr) -#else -#define SGI_MSB(regaddr) ((regaddr) | 0x3) -#endif - -#endif /* _ASM_SGI_SGI_H */ diff --git a/include/asm-mips/sgi/wd.h b/include/asm-mips/sgi/wd.h deleted file mode 100644 index 0d6c3a4..0000000 --- a/include/asm-mips/sgi/wd.h +++ /dev/null @@ -1,20 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Copyright (C) 2007 by Ralf Baechle - */ -#ifndef __ASM_SGI_WD_H -#define __ASM_SGI_WD_H - -#include <asm/sgi/hpc3.h> - -struct sgiwd93_platform_data { - unsigned int unit; - unsigned int irq; - struct hpc3_scsiregs *hregs; - unsigned char *wdregs; -}; - -#endif /* __ASM_SGI_WD_H */ |
