diff options
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/net/tulip/Kconfig | 12 | ||||
-rw-r--r-- | drivers/net/tulip/Makefile | 1 | ||||
-rw-r--r-- | drivers/net/tulip/media.c | 36 | ||||
-rw-r--r-- | drivers/net/tulip/timer.c | 1 | ||||
-rw-r--r-- | drivers/net/tulip/tulip.h | 8 | ||||
-rw-r--r-- | drivers/net/tulip/tulip_core.c | 34 | ||||
-rw-r--r-- | drivers/net/tulip/uli526x.c | 1749 |
7 files changed, 1775 insertions, 66 deletions
diff --git a/drivers/net/tulip/Kconfig b/drivers/net/tulip/Kconfig index e2cdaf8..8c9634a 100644 --- a/drivers/net/tulip/Kconfig +++ b/drivers/net/tulip/Kconfig @@ -135,6 +135,18 @@ config DM9102 <file:Documentation/networking/net-modules.txt>. The module will be called dmfe. +config ULI526X + tristate "ULi M526x controller support" + depends on NET_TULIP && PCI + select CRC32 + ---help--- + This driver is for ULi M5261/M5263 10/100M Ethernet Controller + (<http://www.uli.com.tw/>). + + To compile this driver as a module, choose M here and read + <file:Documentation/networking/net-modules.txt>. The module will + be called uli526x. + config PCMCIA_XIRCOM tristate "Xircom CardBus support (new driver)" depends on NET_TULIP && CARDBUS diff --git a/drivers/net/tulip/Makefile b/drivers/net/tulip/Makefile index 8bb9b46..451090d 100644 --- a/drivers/net/tulip/Makefile +++ b/drivers/net/tulip/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_WINBOND_840) += winbond-840.o obj-$(CONFIG_DE2104X) += de2104x.o obj-$(CONFIG_TULIP) += tulip.o obj-$(CONFIG_DE4X5) += de4x5.o +obj-$(CONFIG_ULI526X) += uli526x.o # Declare multi-part drivers. diff --git a/drivers/net/tulip/media.c b/drivers/net/tulip/media.c index e26c31f..f53396f 100644 --- a/drivers/net/tulip/media.c +++ b/drivers/net/tulip/media.c @@ -81,25 +81,6 @@ int tulip_mdio_read(struct net_device *dev, int phy_id, int location) return retval & 0xffff; } - if(tp->chip_id == ULI526X && tp->revision >= 0x40) { - int value; - int i = 1000; - - value = ioread32(ioaddr + CSR9); - iowrite32(value & 0xFFEFFFFF, ioaddr + CSR9); - - value = (phy_id << 21) | (location << 16) | 0x08000000; - iowrite32(value, ioaddr + CSR10); - - while(--i > 0) { - mdio_delay(); - if(ioread32(ioaddr + CSR10) & 0x10000000) - break; - } - retval = ioread32(ioaddr + CSR10); - spin_unlock_irqrestore(&tp->mii_lock, flags); - return retval & 0xFFFF; - } /* Establish sync by sending at least 32 logic ones. */ for (i = 32; i >= 0; i--) { iowrite32(MDIO_ENB | MDIO_DATA_WRITE1, mdio_addr); @@ -159,23 +140,6 @@ void tulip_mdio_write(struct net_device *dev, int phy_id, int location, int val) spin_unlock_irqrestore(&tp->mii_lock, flags); return; } - if (tp->chip_id == ULI526X && tp->revision >= 0x40) { - int value; - int i = 1000; - - value = ioread32(ioaddr + CSR9); - iowrite32(value & 0xFFEFFFFF, ioaddr + CSR9); - - value = (phy_id << 21) | (location << 16) | 0x04000000 | (val & 0xFFFF); - iowrite32(value, ioaddr + CSR10); - - while(--i > 0) { - if (ioread32(ioaddr + CSR10) & 0x10000000) - break; - } - spin_unlock_irqrestore(&tp->mii_lock, flags); - return; - } /* Establish sync by sending 32 logic ones. */ for (i = 32; i >= 0; i--) { diff --git a/drivers/net/tulip/timer.c b/drivers/net/tulip/timer.c index 6915682..e058a9f 100644 --- a/drivers/net/tulip/timer.c +++ b/drivers/net/tulip/timer.c @@ -39,7 +39,6 @@ void tulip_timer(unsigned long data) case MX98713: case COMPEX9881: case DM910X: - case ULI526X: default: { struct medialeaf *mleaf; unsigned char *p; diff --git a/drivers/net/tulip/tulip.h b/drivers/net/tulip/tulip.h index 20346d8..05d2d96 100644 --- a/drivers/net/tulip/tulip.h +++ b/drivers/net/tulip/tulip.h @@ -88,7 +88,6 @@ enum chips { I21145, DM910X, CONEXANT, - ULI526X }; @@ -482,11 +481,8 @@ static inline void tulip_stop_rxtx(struct tulip_private *tp) static inline void tulip_restart_rxtx(struct tulip_private *tp) { - if(!(tp->chip_id == ULI526X && - (tp->revision == 0x40 || tp->revision == 0x50))) { - tulip_stop_rxtx(tp); - udelay(5); - } + tulip_stop_rxtx(tp); + udelay(5); tulip_start_rxtx(tp); } diff --git a/drivers/net/tulip/tulip_core.c b/drivers/net/tulip/tulip_core.c index d45d8f5..05da5be 100644 --- a/drivers/net/tulip/tulip_core.c +++ b/drivers/net/tulip/tulip_core.c @@ -199,9 +199,6 @@ struct tulip_chip_table tulip_tbl[] = { { "Conexant LANfinity", 256, 0x0001ebef, HAS_MII | HAS_ACPI, tulip_timer }, - /* ULi526X */ - { "ULi M5261/M5263", 128, 0x0001ebef, - HAS_MII | HAS_MEDIA_TABLE | CSR12_IN_SROM | HAS_ACPI, tulip_timer }, }; @@ -239,8 +236,6 @@ static struct pci_device_id tulip_pci_tbl[] = { { 0x1737, 0xAB09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET }, { 0x1737, 0xAB08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET }, { 0x17B3, 0xAB08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET }, - { 0x10b9, 0x5261, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ULI526X }, /* ALi 1563 integrated ethernet */ - { 0x10b9, 0x5263, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ULI526X }, /* ALi 1563 integrated ethernet */ { 0x10b7, 0x9300, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET }, /* 3Com 3CSOHO100B-TX */ { 0x14ea, 0xab08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET }, /* Planex FNW-3602-TX */ { } /* terminate list */ @@ -522,7 +517,7 @@ static void tulip_tx_timeout(struct net_device *dev) dev->name); } else if (tp->chip_id == DC21140 || tp->chip_id == DC21142 || tp->chip_id == MX98713 || tp->chip_id == COMPEX9881 - || tp->chip_id == DM910X || tp->chip_id == ULI526X) { + || tp->chip_id == DM910X) { printk(KERN_WARNING "%s: 21140 transmit timed out, status %8.8x, " "SIA %8.8x %8.8x %8.8x %8.8x, resetting...\n", dev->name, ioread32(ioaddr + CSR5), ioread32(ioaddr + CSR12), @@ -1103,18 +1098,16 @@ static void set_rx_mode(struct net_device *dev) entry = tp->cur_tx++ % TX_RING_SIZE; if (entry != 0) { - /* Avoid a chip errata by prefixing a dummy entry. Don't do - this on the ULI526X as it triggers a different problem */ - if (!(tp->chip_id == ULI526X && (tp->revision == 0x40 || tp->revision == 0x50))) { - tp->tx_buffers[entry].skb = NULL; - tp->tx_buffers[entry].mapping = 0; - tp->tx_ring[entry].length = - (entry == TX_RING_SIZE-1) ? cpu_to_le32(DESC_RING_WRAP) : 0; - tp->tx_ring[entry].buffer1 = 0; - /* Must set DescOwned later to avoid race with chip */ - dummy = entry; - entry = tp->cur_tx++ % TX_RING_SIZE; - } + /* Avoid a chip errata by prefixing a dummy entry. */ + tp->tx_buffers[entry].skb = NULL; + tp->tx_buffers[entry].mapping = 0; + tp->tx_ring[entry].length = + (entry == TX_RING_SIZE-1) ? cpu_to_le32(DESC_RING_WRAP) : 0; + tp->tx_ring[entry].buffer1 = 0; + /* Must set DescOwned later to avoid race with chip */ + dummy = entry; + entry = tp->cur_tx++ % TX_RING_SIZE; + } tp->tx_buffers[entry].skb = NULL; @@ -1235,10 +1228,6 @@ static int tulip_uli_dm_quirk(struct pci_dev *pdev) { if (pdev->vendor == 0x1282 && pdev->device == 0x9102) return 1; - if (pdev->vendor == 0x10b9 && pdev->device == 0x5261) - return 1; - if (pdev->vendor == 0x10b9 && pdev->device == 0x5263) - return 1; return 0; } @@ -1680,7 +1669,6 @@ static int __devinit tulip_init_one (struct pci_dev *pdev, switch (chip_idx) { case DC21140: case DM910X: - case ULI526X: default: if (tp->mtable) iowrite32(tp->mtable->csr12dir | 0x100, ioaddr + CSR12); diff --git a/drivers/net/tulip/uli526x.c b/drivers/net/tulip/uli526x.c new file mode 100644 index 0000000..5ae22b7 --- /dev/null +++ b/drivers/net/tulip/uli526x.c @@ -0,0 +1,1749 @@ +/* + This program is free software; you can redistribute it and/or + modify it under the terms of the GNU General Public License + as published by the Free Software Foundation; either version 2 + of the License, or (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + +*/ + +#define DRV_NAME "uli526x" +#define DRV_VERSION "0.9.3" +#define DRV_RELDATE "2005-7-29" + +#include <linux/module.h> + +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/timer.h> +#include <linux/ptrace.h> +#include <linux/errno.h> +#include <linux/ioport.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/ethtool.h> +#include <linux/skbuff.h> +#include <linux/delay.h> +#include <linux/spinlock.h> + +#include <asm/processor.h> +#include <asm/bitops.h> +#include <asm/io.h> +#include <asm/dma.h> +#include <asm/uaccess.h> + + +/* Board/System/Debug information/definition ---------------- */ +#define PCI_ULI5261_ID 0x526110B9 /* ULi M5261 ID*/ +#define PCI_ULI5263_ID 0x526310B9 /* ULi M5263 ID*/ + +#define ULI526X_IO_SIZE 0x100 +#define TX_DESC_CNT 0x20 /* Allocated Tx descriptors */ +#define RX_DESC_CNT 0x30 /* Allocated Rx descriptors */ +#define TX_FREE_DESC_CNT (TX_DESC_CNT - 2) /* Max TX packet count */ +#define TX_WAKE_DESC_CNT (TX_DESC_CNT - 3) /* TX wakeup count */ +#define DESC_ALL_CNT (TX_DESC_CNT + RX_DESC_CNT) +#define TX_BUF_ALLOC 0x600 +#define RX_ALLOC_SIZE 0x620 +#define ULI526X_RESET 1 +#define CR0_DEFAULT 0 +#define CR6_DEFAULT 0x22200000 +#define CR7_DEFAULT 0x180c1 +#define CR15_DEFAULT 0x06 /* TxJabber RxWatchdog */ +#define TDES0_ERR_MASK 0x4302 /* TXJT, LC, EC, FUE */ +#define MAX_PACKET_SIZE 1514 +#define ULI5261_MAX_MULTICAST 14 +#define RX_COPY_SIZE 100 +#define MAX_CHECK_PACKET 0x8000 + +#define ULI526X_10MHF 0 +#define ULI526X_100MHF 1 +#define ULI526X_10MFD 4 +#define ULI526X_100MFD 5 +#define ULI526X_AUTO 8 + +#define ULI526X_TXTH_72 0x400000 /* TX TH 72 byte */ +#define ULI526X_TXTH_96 0x404000 /* TX TH 96 byte */ +#define ULI526X_TXTH_128 0x0000 /* TX TH 128 byte */ +#define ULI526X_TXTH_256 0x4000 /* TX TH 256 byte */ +#define ULI526X_TXTH_512 0x8000 /* TX TH 512 byte */ +#define ULI526X_TXTH_1K 0xC000 /* TX TH 1K byte */ + +#define ULI526X_TIMER_WUT (jiffies + HZ * 1)/* timer wakeup time : 1 second */ +#define ULI526X_TX_TIMEOUT ((16*HZ)/2) /* tx packet time-out time 8 s" */ +#define ULI526X_TX_KICK (4*HZ/2) /* tx packet Kick-out time 2 s" */ + +#define ULI526X_DBUG(dbug_now, msg, value) if (uli526x_debug || (dbug_now)) printk(KERN_ERR DRV_NAME ": %s %lx\n", (msg), (long) (value)) + +#define SHOW_MEDIA_TYPE(mode) printk(KERN_ERR DRV_NAME ": Change Speed to %sMhz %s duplex\n",mode & 1 ?"100":"10", mode & 4 ? "full":"half"); + + +/* CR9 definition: SROM/MII */ +#define CR9_SROM_READ 0x4800 +#define CR9_SRCS 0x1 +#define CR9_SRCLK 0x2 +#define CR9_CRDOUT 0x8 +#define SROM_DATA_0 0x0 +#define SROM_DATA_1 0x4 +#define PHY_DATA_1 0x20000 +#define PHY_DATA_0 0x00000 +#define MDCLKH 0x10000 + +#define PHY_POWER_DOWN 0x800 + +#define SROM_V41_CODE 0x14 + +#define SROM_CLK_WRITE(data, ioaddr) \ + outl(data|CR9_SROM_READ|CR9_SRCS,ioaddr); \ + udelay(5); \ + outl(data|CR9_SROM_READ|CR9_SRCS|CR9_SRCLK,ioaddr); \ + udelay(5); \ + outl(data|CR9_SROM_READ|CR9_SRCS,ioaddr); \ + udelay(5); + +/* Structure/enum declaration ------------------------------- */ +struct tx_desc { + u32 tdes0, tdes1, tdes2, tdes3; /* Data for the card */ + char *tx_buf_ptr; /* Data for us */ + struct tx_desc *next_tx_desc; +} __attribute__(( aligned(32) )); + +struct rx_desc { + u32 rdes0, rdes1, rdes2, rdes3; /* Data for the card */ + struct sk_buff *rx_skb_ptr; /* Data for us */ + struct rx_desc *next_rx_desc; +} __attribute__(( aligned(32) )); + +struct uli526x_board_info { + u32 chip_id; /* Chip vendor/Device ID */ + struct net_device *next_dev; /* next device */ + struct pci_dev *pdev; /* PCI device */ + spinlock_t lock; + + long ioaddr; /* I/O base address */ + u32 cr0_data; + u32 cr5_data; + u32 cr6_data; + u32 cr7_data; + u32 cr15_data; + + /* pointer for memory physical address */ + dma_addr_t buf_pool_dma_ptr; /* Tx buffer pool memory */ + dma_addr_t buf_pool_dma_start; /* Tx buffer pool align dword */ + dma_addr_t desc_pool_dma_ptr; /* descriptor pool memory */ + dma_addr_t first_tx_desc_dma; + dma_addr_t first_rx_desc_dma; + + /* descriptor pointer */ + unsigned char *buf_pool_ptr; /* Tx buffer pool memory */ + unsigned char *buf_pool_start; /* Tx buffer pool align dword */ + unsigned char *desc_pool_ptr; /* descriptor pool memory */ + struct tx_desc *first_tx_desc; + struct tx_desc *tx_insert_ptr; + struct tx_desc *tx_remove_ptr; + struct rx_desc *first_rx_desc; + struct rx_desc *rx_insert_ptr; + struct rx_desc *rx_ready_ptr; /* packet come pointer */ + unsigned long tx_packet_cnt; /* transmitted packet count */ + unsigned long rx_avail_cnt; /* available rx descriptor count */ + unsigned long interval_rx_cnt; /* rx packet count a callback time */ + + u16 dbug_cnt; + u16 NIC_capability; /* NIC media capability */ + u16 PHY_reg4; /* Saved Phyxcer register 4 value */ + + u8 media_mode; /* user specify media mode */ + u8 op_mode; /* real work media mode */ + u8 phy_addr; + u8 link_failed; /* Ever link failed */ + u8 wait_reset; /* Hardware failed, need to reset */ + struct timer_list timer; + + /* System defined statistic counter */ + struct net_device_stats stats; + + /* Driver defined statistic counter */ + unsigned long tx_fifo_underrun; + unsigned long tx_loss_carrier; + unsigned long tx_no_carrier; + unsigned long tx_late_collision; + unsigned long tx_excessive_collision; + unsigned long tx_jabber_timeout; + unsigned long reset_count; + unsigned long reset_cr8; + unsigned long reset_fatal; + unsigned long reset_TXtimeout; + + /* NIC SROM data */ + unsigned char srom[128]; + u8 init; +}; + +enum uli526x_offsets { + DCR0 = 0x00, DCR1 = 0x08, DCR2 = 0x10, DCR3 = 0x18, DCR4 = 0x20, + DCR5 = 0x28, DCR6 = 0x30, DCR7 = 0x38, DCR8 = 0x40, DCR9 = 0x48, + DCR10 = 0x50, DCR11 = 0x58, DCR12 = 0x60, DCR13 = 0x68, DCR14 = 0x70, + DCR15 = 0x78 +}; + +enum uli526x_CR6_bits { + CR6_RXSC = 0x2, CR6_PBF = 0x8, CR6_PM = 0x40, CR6_PAM = 0x80, + CR6_FDM = 0x200, CR6_TXSC = 0x2000, CR6_STI = 0x100000, + CR6_SFT = 0x200000, CR6_RXA = 0x40000000, CR6_NO_PURGE = 0x20000000 +}; + +/* Global variable declaration ----------------------------- */ +static int __devinitdata printed_version; +static char version[] __devinitdata = + KERN_INFO DRV_NAME ": ULi M5261/M5263 net driver, version " + DRV_VERSION " (" DRV_RELDATE ")\n"; + +static int uli526x_debug; +static unsigned char uli526x_media_mode = ULI526X_AUTO; +static u32 uli526x_cr6_user_set; + +/* For module input parameter */ +static int debug; +static u32 cr6set; +static unsigned char mode = 8; + +/* function declaration ------------------------------------- */ +static int uli526x_open(struct net_device *); +static int uli526x_start_xmit(struct sk_buff *, struct net_device *); +static int uli526x_stop(struct net_device *); +static struct net_device_stats * uli526x_get_stats(struct net_device *); +static void uli526x_set_filter_mode(struct net_device *); +static struct ethtool_ops netdev_ethtool_ops; +static u16 read_srom_word(long, int); +static irqreturn_t uli526x_interrupt(int, void *, struct pt_regs *); +static void uli526x_descriptor_init(struct uli526x_board_info *, unsigned long); +static void allocate_rx_buffer(struct uli526x_board_info *); +static void update_cr6(u32, unsigned long); +static void send_filter_frame(struct net_device *, int); +static u16 phy_read(unsigned long, u8, u8, u32); +static u16 phy_readby_cr10(unsigned long, u8, u8); +static void phy_write(unsigned long, u8, u8, u16, u32); +static void phy_writeby_cr10(unsigned long, u8, u8, u16); +static void phy_write_1bit(unsigned long, u32, u32); +static u16 phy_read_1bit(unsigned long, u32); +static u8 uli526x_sense_speed(struct uli526x_board_info *); +static void uli526x_process_mode(struct uli526x_board_info *); +static void uli526x_timer(unsigned long); +static void uli526x_rx_packet(struct net_device *, struct uli526x_board_info *); +static void uli526x_free_tx_pkt(struct net_device *, struct uli526x_board_info *); +static void uli526x_reuse_skb(struct uli526x_board_info *, struct sk_buff *); +static void uli526x_dynamic_reset(struct net_device *); +static void uli526x_free_rxbuffer(struct uli526x_board_info *); +static void uli526x_init(struct net_device *); +static void uli526x_set_phyxcer(struct uli526x_board_info *); + +/* ULI526X network board routine ---------------------------- */ + +/* + * Search ULI526X board, allocate space and register it + */ + +static int __devinit uli526x_init_one (struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + struct uli526x_board_info *db; /* board information structure */ + struct net_device *dev; + int i, err; + + ULI526X_DBUG(0, "uli526x_init_one()", 0); + + if (!printed_version++) + printk(version); + + /* Init network device */ + dev = alloc_etherdev(sizeof(*db)); + if (dev == NULL) + return -ENOMEM; + SET_MODULE_OWNER(dev); + SET_NETDEV_DEV(dev, &pdev->dev); + + if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) { + printk(KERN_WARNING DRV_NAME ": 32-bit PCI DMA not available.\n"); + err = -ENODEV; + goto err_out_free; + } + + /* Enable Master/IO access, Disable memory access */ + err = pci_enable_device(pdev); + if (err) + goto err_out_free; + + if (!pci_resource_start(pdev, 0)) { + printk(KERN_ERR DRV_NAME ": I/O base is zero\n"); + err = -ENODEV; + goto err_out_disable; + } + + if (pci_resource_len(pdev, 0) < (ULI526X_IO_SIZE) ) { + printk(KERN_ERR DRV_NAME ": Allocated I/O size too small\n"); + err = -ENODEV; + goto err_out_disable; + } + + if (pci_request_regions(pdev, DRV_NAME)) { + printk(KERN_ERR DRV_NAME ": Failed to request PCI regions\n"); + err = -ENODEV; + goto err_out_disable; + } + + /* Init system & device */ + db = netdev_priv(dev); + + /* Allocate Tx/Rx descriptor memory */ + db->desc_pool_ptr = pci_alloc_consistent(pdev, sizeof(struct tx_desc) * DESC_ALL_CNT + 0x20, &db->desc_pool_dma_ptr); + if(db->desc_pool_ptr == NULL) + { + err = -ENOMEM; + goto err_out_nomem; + } + db->buf_pool_ptr = pci_alloc_consistent(pdev, TX_BUF_ALLOC * TX_DESC_CNT + 4, &db->buf_pool_dma_ptr); + if(db->buf_pool_ptr == NULL) + { + err = -ENOMEM; + goto err_out_nomem; + } + + db->first_tx_desc = (struct tx_desc *) db->desc_pool_ptr; + db->first_tx_desc_dma = db->desc_pool_dma_ptr; + db->buf_pool_start = db->buf_pool_ptr; + db->buf_pool_dma_start = db->buf_pool_dma_ptr; + + db->chip_id = ent->driver_data; + db->ioaddr = pci_resource_start(pdev, 0); + + db->pdev = pdev; + db->init = 1; + + dev->base_addr = db->ioaddr; + dev->irq = pdev->irq; + pci_set_drvdata(pdev, dev); + + /* Register some necessary functions */ + dev->open = &uli526x_open; + dev->hard_start_xmit = &uli526x_start_xmit; + dev->stop = &uli526x_stop; + dev->get_stats = &uli526x_get_stats; + dev->set_multicast_list = &uli526x_set_filter_mode; + dev->ethtool_ops = &netdev_ethtool_ops; + spin_lock_init(&db->lock); + + + /* read 64 word srom data */ + for (i = 0; i < 64; i++) + ((u16 *) db->srom)[i] = cpu_to_le16(read_srom_word(db->ioaddr, i)); + + /* Set Node address */ + if(((u16 *) db->srom)[0] == 0xffff || ((u16 *) db->srom)[0] == 0) /* SROM absent, so read MAC address from ID Table */ + { + outl(0x10000, db->ioaddr + DCR0); //Diagnosis mode + outl(0x1c0, db->ioaddr + DCR13); //Reset dianostic pointer port + outl(0, db->ioaddr + DCR14); //Clear reset port + outl(0x10, db->ioaddr + DCR14); //Reset ID Table pointer + outl(0, db->ioaddr + DCR14); //Clear reset port + outl(0, db->ioaddr + DCR13); //Clear CR13 + outl(0x1b0, db->ioaddr + DCR13); //Select ID Table access port + //Read MAC address from CR14 + for (i = 0; i < 6; i++) + dev->dev_addr[i] = inl(db->ioaddr + DCR14); + //Read end + outl(0, db->ioaddr + DCR13); //Clear CR13 + outl(0, db->ioaddr + DCR0); //Clear CR0 + udelay(10); + } + else /*Exist SROM*/ + { + for (i = 0; i < 6; i++) + dev->dev_addr[i] = db->srom[20 + i]; + } + err = register_netdev (dev); + if (err) + goto err_out_res; + + printk(KERN_INFO "%s: ULi M%04lx at pci%s,",dev->name,ent->driver_data >> 16,pci_name(pdev)); + + for (i = 0; i < 6; i++) + printk("%c%02x", i ? ':' : ' ', dev->dev_addr[i]); + printk(", irq %d.\n", dev->irq); + + pci_set_master(pdev); + + return 0; + +err_out_res: + pci_release_regions(pdev); +err_out_nomem: + if(db->desc_pool_ptr) + pci_free_consistent(pdev, sizeof(struct tx_desc) * DESC_ALL_CNT + 0x20, + db->desc_pool_ptr, db->desc_pool_dma_ptr); + + if(db->buf_pool_ptr != NULL) + pci_free_consistent(pdev, TX_BUF_ALLOC * TX_DESC_CNT + 4, + db->buf_pool_ptr, db->buf_pool_dma_ptr); +err_out_disable: + pci_disable_device(pdev); +err_out_free: + pci_set_drvdata(pdev, NULL); + free_netdev(dev); + + return err; +} + + +static void __devexit uli526x_remove_one (struct pci_dev *pdev) +{ + struct net_device *dev = pci_get_drvdata(pdev); + struct uli526x_board_info *db = netdev_priv(dev); + + ULI526X_DBUG(0, "uli526x_remove_one()", 0); + + pci_free_consistent(db->pdev, sizeof(struct tx_desc) * + DESC_ALL_CNT + 0x20, db->desc_pool_ptr, + db->desc_pool_dma_ptr); + pci_free_consistent(db->pdev, TX_BUF_ALLOC * TX_DESC_CNT + 4, + db->buf_pool_ptr, db->buf_pool_dma_ptr); + unregister_netdev(dev); + pci_release_regions(pdev); + free_netdev(dev); /* free board information */ + pci_set_drvdata(pdev, NULL); + pci_disable_device(pdev); + ULI526X_DBUG(0, "uli526x_remove_one() exit", 0); +} + + +/* + * Open the interface. + * The interface is opened whenever "ifconfig" activates it. + */ + +static int uli526x_open(struct net_device *dev) +{ + int ret; + struct uli526x_board_info *db = netdev_priv(dev); + + ULI526X_DBUG(0, "uli526x_open", 0); + + ret = request_irq(dev->irq, &uli526x_interrupt, SA_SHIRQ, dev->name, dev); + if (ret) + return ret; + + /* system variable init */ + db->cr6_data = CR6_DEFAULT | uli526x_cr6_user_set; + db->tx_packet_cnt = 0; + db->rx_avail_cnt = 0; + db->link_failed = 1; + netif_carrier_off(dev); + db->wait_reset = 0; + + db->NIC_capability = 0xf; /* All capability*/ + db->PHY_reg4 = 0x1e0; + + /* CR6 operation mode decision */ + db->cr6_data |= ULI526X_TXTH_256; + db->cr0_data = CR0_DEFAULT; + + /* Initialize ULI526X board */ + uli526x_init(dev); + + /* Active System Interface */ + netif_wake_queue(dev); + + /* set and active a timer process */ + init_timer(&db->timer); + db->timer.expires = ULI526X_TIMER_WUT + HZ * 2; + db->timer.data = (unsigned long)dev; + db->timer.function = &uli526x_timer; + add_timer(&db->timer); + + return 0; +} + + +/* Initialize ULI526X board + * Reset ULI526X board + * Initialize TX/Rx descriptor chain structure + * Send the set-up frame + * Enable Tx/Rx machine + */ + +static void uli526x_init(struct net_device *dev) +{ + struct uli526x_board_info *db = netdev_priv(dev); + unsigned long ioaddr = db->ioaddr; + u8 phy_tmp; + u16 phy_value; + u16 phy_reg_reset; + + ULI526X_DBUG(0, "uli526x_init()", 0); + + /* Reset M526x MAC controller */ + outl(ULI526X_RESET, ioaddr + DCR0); /* RESET MAC */ + udelay(100); + outl(db->cr0_data, ioaddr + DCR0); + udelay(5); + + /* Phy addr : In some boards,M5261/M5263 phy address != 1 */ + db->phy_addr = 1; + for(phy_tmp=0;phy_tmp<32;phy_tmp++) + { + phy_value=phy_read(db->ioaddr,phy_tmp,3,db->chip_id);//peer add + if(phy_value != 0xffff&&phy_value!=0) + { + db->phy_addr = phy_tmp; + break; + } + } + if(phy_tmp == 32) + printk(KERN_WARNING "Can not find the phy address!!!"); + /* Parser SROM and media mode */ + db->media_mode = uli526x_media_mode; + + /* Phyxcer capability setting */ + phy_reg_reset = phy_read(db->ioaddr, db->phy_addr, 0, db->chip_id); + phy_reg_reset = (phy_reg_reset | 0x8000); + phy_write(db->ioaddr, db->phy_addr, 0, phy_reg_reset, db->chip_id); + udelay(500); + + /* Process Phyxcer Media Mode */ + uli526x_set_phyxcer(db); + + /* Media Mode Process */ + if ( !(db->media_mode & ULI526X_AUTO) ) + db->op_mode = db->media_mode; /* Force Mode */ + + /* Initialize Transmit/Receive decriptor and CR3/4 */ + uli526x_descriptor_init(db, ioaddr); + + /* Init CR6 to program M526X operation */ + update_cr6(db->cr6_data, ioaddr); + + /* Send setup frame */ + send_filter_frame(dev, dev->mc_count); /* M5261/M5263 */ + + /* Init CR7, interrupt active bit */ + db->cr7_data = CR7_DEFAULT; + outl(db->cr7_data, ioaddr + DCR7); + + /* Init CR15, Tx jabber and Rx watchdog timer */ + outl(db->cr15_data, ioaddr + DCR15); + + /* Enable ULI526X Tx/Rx function */ + db->cr6_data |= CR6_RXSC | CR6_TXSC; + update_cr6(db->cr6_data, ioaddr); +} + + +/* + * Hardware start transmission. + * Send a packet to media from the upper layer. + */ + +static int uli526x_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct uli526x_board_info *db = netdev_priv(dev); + struct tx_desc *txptr; + unsigned long flags; + + ULI526X_DBUG(0, "uli526x_start_xmit", 0); + + /* Resource flag check */ + netif_stop_queue(dev); + + /* Too large packet check */ + if (skb->len > MAX_PACKET_SIZE) { + printk(KERN_ERR DRV_NAME ": big packet = %d\n", (u16)skb->len); + dev_kfree_skb(skb); + return 0; + } + + spin_lock_irqsave(&db->lock, flags); + + /* No Tx resource check, it never happen nromally */ + if (db->tx_packet_cnt >= TX_FREE_DESC_CNT) { + spin_unlock_irqrestore(&db->lock, flags); + printk(KERN_ERR DRV_NAME ": No Tx resource %ld\n", db->tx_packet_cnt); + return 1; + } + + /* Disable NIC interrupt */ + outl(0, dev->base_addr + DCR7); + + /* transmit this packet */ + txptr = db->tx_insert_ptr; + memcpy(txptr->tx_buf_ptr, skb->data, skb->len); + txptr->tdes1 = cpu_to_le32(0xe1000000 | skb->len); + + /* Point to next transmit free descriptor */ + db->tx_insert_ptr = txptr->next_tx_desc; + + /* Transmit Packet Process */ + if ( (db->tx_packet_cnt < TX_DESC_CNT) ) { + txptr->tdes0 = cpu_to_le32(0x80000000); /* Set owner bit */ + db->tx_packet_cnt++; /* Ready to send */ + outl(0x1, dev->base_addr + DCR1); /* Issue Tx polling */ + dev->trans_start = jiffies; /* saved time stamp */ + } + + /* Tx resource check */ + if ( db->tx_packet_cnt < TX_FREE_DESC_CNT ) + netif_wake_queue(dev); + + /* Restore CR7 to enable interrupt */ + spin_unlock_irqrestore(&db->lock, flags); + outl(db->cr7_data, dev->base_addr + DCR7); + + /* free this SKB */ + dev_kfree_skb(skb); + + return 0; +} + + +/* + * Stop the interface. + * The interface is stopped when it is brought. + */ + +static int uli526x_stop(struct net_device *dev) +{ + struct uli526x_board_info *db = netdev_priv(dev); + unsigned long ioaddr = dev->base_addr; + + ULI526X_DBUG(0, "uli526x_stop", 0); + + /* disable system */ + netif_stop_queue(dev); + + /* deleted timer */ + del_timer_sync(&db->timer); + + /* Reset & stop ULI526X board */ + outl(ULI526X_RESET, ioaddr + DCR0); + udelay(5); + phy_write(db->ioaddr, db->phy_addr, 0, 0x8000, db->chip_id); + + /* free interrupt */ + free_irq(dev->irq, dev); + + /* free allocated rx buffer */ + uli526x_free_rxbuffer(db); + +#if 0 + /* show statistic counter */ + printk(DRV_NAME ": FU:%lx EC:%lx LC:%lx NC:%lx LOC:%lx TXJT:%lx RESET:%lx RCR8:%lx FAL:%lx TT:%lx\n", + db->tx_fifo_underrun, db->tx_excessive_collision, + db->tx_late_collision, db->tx_no_carrier, db->tx_loss_carrier, + db->tx_jabber_timeout, db->reset_count, db->reset_cr8, + db->reset_fatal, db->reset_TXtimeout); +#endif + + return 0; +} + + +/* + * M5261/M5263 insterrupt handler + * receive the packet to upper layer, free the transmitted packet + */ + +static irqreturn_t uli526x_interrupt(int irq, void *dev_id, struct pt_regs *regs) +{ + struct net_device *dev = dev_id; + struct uli526x_board_info *db = netdev_priv(dev); + unsigned long ioaddr = dev->base_addr; + unsigned long flags; + + if (!dev) { + ULI526X_DBUG(1, "uli526x_interrupt() without DEVICE arg", 0); + return IRQ_NONE; + } + + spin_lock_irqsave(&db->lock, flags); + outl(0, ioaddr + DCR7); + + /* Got ULI526X status */ + db->cr5_data = inl(ioaddr + DCR5); + outl(db->cr5_data, ioaddr + DCR5); + if ( !(db->cr5_data & 0x180c1) ) { + spin_unlock_irqrestore(&db->lock, flags); + outl(db->cr7_data, ioaddr + DCR7); + return IRQ_HANDLED; + } + + /* Check system status */ + if (db->cr5_data & 0x2000) { + /* system bus error happen */ + ULI526X_DBUG(1, "System bus error happen. CR5=", db->cr5_data); + db->reset_fatal++; + db->wait_reset = 1; /* Need to RESET */ + spin_unlock_irqrestore(&db->lock, flags); + return IRQ_HANDLED; + } + + /* Received the coming packet */ + if ( (db->cr5_data & 0x40) && db->rx_avail_cnt ) + uli526x_rx_packet(dev, db); + + /* reallocate rx descriptor buffer */ + if (db->rx_avail_cnt<RX_DESC_CNT) + allocate_rx_buffer(db); + + /* Free the transmitted descriptor */ + if ( db->cr5_data & 0x01) + uli526x_free_tx_pkt(dev, db); + + /* Restore CR7 to enable interrupt mask */ + outl(db->cr7_data, ioaddr + DCR7); + + spin_unlock_irqrestore(&db->lock, flags); + return IRQ_HANDLED; +} + + +/* + * Free TX resource after TX complete + */ + +static void uli526x_free_tx_pkt(struct net_device *dev, struct uli526x_board_info * db) +{ + struct tx_desc *txptr; + u32 tdes0; + + txptr = db->tx_remove_ptr; + while(db->tx_packet_cnt) { + tdes0 = le32_to_cpu(txptr->tdes0); + /* printk(DRV_NAME ": tdes0=%x\n", tdes0); */ + if (tdes0 & 0x80000000) + break; + + /* A packet sent completed */ + db->tx_packet_cnt--; + db->stats.tx_packets++; + + /* Transmit statistic counter */ + if ( tdes0 != 0x7fffffff ) { + /* printk(DRV_NAME ": tdes0=%x\n", tdes0); */ + db->stats.collisions += (tdes0 >> 3) & 0xf; + db->stats.tx_bytes += le32_to_cpu(txptr->tdes1) & 0x7ff; + if (tdes0 & TDES0_ERR_MASK) { + db->stats.tx_errors++; + if (tdes0 & 0x0002) { /* UnderRun */ + db->tx_fifo_underrun++; + if ( !(db->cr6_data & CR6_SFT) ) { + db->cr6_data = db->cr6_data | CR6_SFT; + update_cr6(db->cr6_data, db->ioaddr); + } + } + if (tdes0 & 0x0100) + db->tx_excessive_collision++; + if (tdes0 & 0x0200) + db->tx_late_collision++; + if (tdes0 & 0x0400) + db->tx_no_carrier++; + if (tdes0 & 0x0800) + db->tx_loss_carrier++; + if (tdes0 & 0x4000) + db->tx_jabber_timeout++; + } + } + + txptr = txptr->next_tx_desc; + }/* End of while */ + + /* Update TX remove pointer to next */ + db->tx_remove_ptr = txptr; + + /* Resource available check */ + if ( db->tx_packet_cnt < TX_WAKE_DESC_CNT ) + netif_wake_queue(dev); /* Active upper layer, send again */ +} + + +/* + * Receive the come packet and pass to upper layer + */ + +static void uli526x_rx_packet(struct net_device *dev, struct uli526x_board_info * db) +{ + struct rx_desc *rxptr; + struct sk_buff *skb; + int rxlen; + u32 rdes0; + + rxptr = db->rx_ready_ptr; + + while(db->rx_avail_cnt) { + rdes0 = le32_to_cpu(rxptr->rdes0); + if (rdes0 & 0x80000000) /* packet owner check */ + { + break; + } + + db->rx_avail_cnt--; + db->interval_rx_cnt++; + + pci_unmap_single(db->pdev, le32_to_cpu(rxptr->rdes2), RX_ALLOC_SIZE, PCI_DMA_FROMDEVICE); + if ( (rdes0 & 0x300) != 0x300) { + /* A packet without First/Last flag */ + /* reuse this SKB */ + ULI526X_DBUG(0, "Reuse SK buffer, rdes0", rdes0); + uli526x_reuse_skb(db, rxptr->rx_skb_ptr); + } else { + /* A packet with First/Last flag */ + rxlen = ( (rdes0 >> 16) & 0x3fff) - 4; + + /* error summary bit check */ + if (rdes0 & 0x8000) { + /* This is a error packet */ + //printk(DRV_NAME ": rdes0: %lx\n", rdes0); + db->stats.rx_errors++; + if (rdes0 & 1) + db->stats.rx_fifo_errors++; + if (rdes0 & 2) + db->stats.rx_crc_errors++; + if (rdes0 & 0x80) + db->stats.rx_length_errors++; + } + + if ( !(rdes0 & 0x8000) || + ((db->cr6_data & CR6_PM) && (rxlen>6)) ) { + skb = rxptr->rx_skb_ptr; + + /* Good packet, send to upper layer */ + /* Shorst packet used new SKB */ + if ( (rxlen < RX_COPY_SIZE) && + ( (skb = dev_alloc_skb(rxlen + 2) ) + != NULL) ) { + /* size less than COPY_SIZE, allocate a rxlen SKB */ + skb->dev = dev; + skb_reserve(skb, 2); /* 16byte align */ + memcpy(skb_put(skb, rxlen), rxptr->rx_skb_ptr->tail, rxlen); + uli526x_reuse_skb(db, rxptr->rx_skb_ptr); + } else { + skb->dev = dev; + skb_put(skb, rxlen); + } + skb->protocol = eth_type_trans(skb, dev); + netif_rx(skb); + dev->last_rx = jiffies; + db->stats.rx_packets++; + db->stats.rx_bytes += rxlen; + + } else { + /* Reuse SKB buffer when the packet is error */ + ULI526X_DBUG(0, "Reuse SK buffer, rdes0", rdes0); + uli526x_reuse_skb(db, rxptr->rx_skb_ptr); + } + } + + rxptr = rxptr->next_rx_desc; + } + + db->rx_ready_ptr = rxptr; +} + + +/* + * Get statistics from driver. + */ + +static struct net_device_stats * uli526x_get_stats(struct net_device *dev) +{ + struct uli526x_board_info *db = netdev_priv(dev); + + ULI526X_DBUG(0, "uli526x_get_stats", 0); + return &db->stats; +} + + +/* + * Set ULI526X multicast address + */ + +static void uli526x_set_filter_mode(struct net_device * dev) +{ + struct uli526x_board_info *db = dev->priv; + unsigned long flags; + + ULI526X_DBUG(0, "uli526x_set_filter_mode()", 0); + spin_lock_irqsave(&db->lock, flags); + + if (dev->flags & IFF_PROMISC) { + ULI526X_DBUG(0, "Enable PROM Mode", 0); + db->cr6_data |= CR6_PM | CR6_PBF; + update_cr6(db->cr6_data, db->ioaddr); + spin_unlock_irqrestore(&db->lock, flags); + return; + } + + if (dev->flags & IFF_ALLMULTI || dev->mc_count > ULI5261_MAX_MULTICAST) { + ULI526X_DBUG(0, "Pass all multicast address", dev->mc_count); + db->cr6_data &= ~(CR6_PM | CR6_PBF); + db->cr6_data |= CR6_PAM; + spin_unlock_irqrestore(&db->lock, flags); + return; + } + + ULI526X_DBUG(0, "Set multicast address", dev->mc_count); + send_filter_frame(dev, dev->mc_count); /* M5261/M5263 */ + spin_unlock_irqrestore(&db->lock, flags); +} + +static void +ULi_ethtool_gset(struct uli526x_board_info *db, struct ethtool_cmd *ecmd) +{ + ecmd->supported = (SUPPORTED_10baseT_Half | + SUPPORTED_10baseT_Full | + SUPPORTED_100baseT_Half | + SUPPORTED_100baseT_Full | + SUPPORTED_Autoneg | + SUPPORTED_MII); + + ecmd->advertising = (ADVERTISED_10baseT_Half | + ADVERTISED_10baseT_Full | + ADVERTISED_100baseT_Half | + ADVERTISED_100baseT_Full | + ADVERTISED_Autoneg | + ADVERTISED_MII); + + + ecmd->port = PORT_MII; + ecmd->phy_address = db->phy_addr; + + ecmd->transceiver = XCVR_EXTERNAL; + + ecmd->speed = 10; + ecmd->duplex = DUPLEX_HALF; + + if(db->op_mode==ULI526X_100MHF || db->op_mode==ULI526X_100MFD) + { + ecmd->speed = 100; + } + if(db->op_mode==ULI526X_10MFD || db->op_mode==ULI526X_100MFD) + { + ecmd->duplex = DUPLEX_FULL; + } + if(db->link_failed) + { + ecmd->speed = -1; + ecmd->duplex = -1; + } + + if (db->media_mode & ULI526X_AUTO) + { + ecmd->autoneg = AUTONEG_ENABLE; + } +} + +static void netdev_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *info) +{ + struct uli526x_board_info *np = netdev_priv(dev); + + strcpy(info->driver, DRV_NAME); + strcpy(info->version, DRV_VERSION); + if (np->pdev) + strcpy(info->bus_info, pci_name(np->pdev)); + else + sprintf(info->bus_info, "EISA 0x%lx %d", + dev->base_addr, dev->irq); +} + +static int netdev_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) { + struct uli526x_board_info *np = netdev_priv(dev); + + ULi_ethtool_gset(np, cmd); + + return 0; +} + +static u32 netdev_get_link(struct net_device *dev) { + struct uli526x_board_info *np = netdev_priv(dev); + + if(np->link_failed) + return 0; + else + return 1; +} + +static void uli526x_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol) +{ + wol->supported = WAKE_PHY | WAKE_MAGIC; + wol->wolopts = 0; +} + +static struct ethtool_ops netdev_ethtool_ops = { + .get_drvinfo = netdev_get_drvinfo, + .get_settings = netdev_get_settings, + .get_link = netdev_get_link, + .get_wol = uli526x_get_wol, +}; + +/* + * A periodic timer routine + * Dynamic media sense, allocate Rx buffer... + */ + +static void uli526x_timer(unsigned long data) +{ + u32 tmp_cr8; + unsigned char tmp_cr12=0; + struct net_device *dev = (struct net_device *) data; + struct uli526x_board_info *db = netdev_priv(dev); + unsigned long flags; + u8 TmpSpeed=10; + + //ULI526X_DBUG(0, "uli526x_timer()", 0); + spin_lock_irqsave(&db->lock, flags); + + + /* Dynamic reset ULI526X : system error or transmit time-out */ + tmp_cr8 = inl(db->ioaddr + DCR8); + if ( (db->interval_rx_cnt==0) && (tmp_cr8) ) { + db->reset_cr8++; + db->wait_reset = 1; + } + db->interval_rx_cnt = 0; + + /* TX polling kick monitor */ + if ( db->tx_packet_cnt && + time_after(jiffies, dev->trans_start + ULI526X_TX_KICK) ) { + outl(0x1, dev->base_addr + DCR1); // Tx polling again + + // TX Timeout + if ( time_after(jiffies, dev->trans_start + ULI526X_TX_TIMEOUT) ) { + db->reset_TXtimeout++; + db->wait_reset = 1; + printk( "%s: Tx timeout - resetting\n", + dev->name); + } + } + + if (db->wait_reset) { + ULI526X_DBUG(0, "Dynamic Reset device", db->tx_packet_cnt); + db->reset_count++; + uli526x_dynamic_reset(dev); + db->timer.expires = ULI526X_TIMER_WUT; + add_timer(&db->timer); + spin_unlock_irqrestore(&db->lock, flags); + return; + } + + /* Link status check, Dynamic media type change */ + if((phy_read(db->ioaddr, db->phy_addr, 5, db->chip_id) & 0x01e0)!=0) + tmp_cr12 = 3; + + if ( !(tmp_cr12 & 0x3) && !db->link_failed ) { + /* Link Failed */ + ULI526X_DBUG(0, "Link Failed", tmp_cr12); + netif_carrier_off(dev); + printk(KERN_INFO "uli526x: %s NIC Link is Down\n",dev->name); + db->link_failed = 1; + + /* For Force 10/100M Half/Full mode: Enable Auto-Nego mode */ + /* AUTO don't need */ + if ( !(db->media_mode & 0x8) ) + phy_write(db->ioaddr, db->phy_addr, 0, 0x1000, db->chip_id); + + /* AUTO mode, if INT phyxcer link failed, select EXT device */ + if (db->media_mode & ULI526X_AUTO) { + db->cr6_data&=~0x00000200; /* bit9=0, HD mode */ + update_cr6(db->cr6_data, db->ioaddr); + } + } else + if ((tmp_cr12 & 0x3) && db->link_failed) { + ULI526X_DBUG(0, "Link link OK", tmp_cr12); + db->link_failed = 0; + + /* Auto Sense Speed */ + if ( (db->media_mode & ULI526X_AUTO) && + uli526x_sense_speed(db) ) + db->link_failed = 1; + uli526x_process_mode(db); + + if(db->link_failed==0) + { + if(db->op_mode==ULI526X_100MHF || db->op_mode==ULI526X_100MFD) + { + TmpSpeed = 100; + } + if(db->op_mode==ULI526X_10MFD || db->op_mode==ULI526X_100MFD) + { + printk(KERN_INFO "uli526x: %s NIC Link is Up %d Mbps Full duplex\n",dev->name,TmpSpeed); + } + else + { + printk(KERN_INFO "uli526x: %s NIC Link is Up %d Mbps Half duplex\n",dev->name,TmpSpeed); + } + netif_carrier_on(dev); + } + /* SHOW_MEDIA_TYPE(db->op_mode); */ + } + else if(!(tmp_cr12 & 0x3) && db->link_failed) + { + if(db->init==1) + { + printk(KERN_INFO "uli526x: %s NIC Link is Down\n",dev->name); + netif_carrier_off(dev); + } + } + db->init=0; + + /* Timer active again */ + db->timer.expires = ULI526X_TIMER_WUT; + add_timer(&db->timer); + spin_unlock_irqrestore(&db->lock, flags); +} + + +/* + * Dynamic reset the ULI526X board + * Stop ULI526X board + * Free Tx/Rx allocated memory + * Reset ULI526X board + * Re-initialize ULI526X board + */ + +static void uli526x_dynamic_reset(struct net_device *dev) +{ + struct uli526x_board_info *db = netdev_priv(dev); + + ULI526X_DBUG(0, "uli526x_dynamic_reset()", 0); + + /* Sopt MAC controller */ + db->cr6_data &= ~(CR6_RXSC | CR6_TXSC); /* Disable Tx/Rx */ + update_cr6(db->cr6_data, dev->base_addr); + outl(0, dev->base_addr + DCR7); /* Disable Interrupt */ + outl(inl(dev->base_addr + DCR5), dev->base_addr + DCR5); + + /* Disable upper layer interface */ + netif_stop_queue(dev); + + /* Free Rx Allocate buffer */ + uli526x_free_rxbuffer(db); + + /* system variable init */ + db->tx_packet_cnt = 0; + db->rx_avail_cnt = 0; + db->link_failed = 1; + db->init=1; + db->wait_reset = 0; + + /* Re-initialize ULI526X board */ + uli526x_init(dev); + + /* Restart upper layer interface */ + netif_wake_queue(dev); +} + + +/* + * free all allocated rx buffer + */ + +static void uli526x_free_rxbuffer(struct uli526x_board_info * db) +{ + ULI526X_DBUG(0, "uli526x_free_rxbuffer()", 0); + + /* free allocated rx buffer */ + while (db->rx_avail_cnt) { + dev_kfree_skb(db->rx_ready_ptr->rx_skb_ptr); + db->rx_ready_ptr = db->rx_ready_ptr->next_rx_desc; + db->rx_avail_cnt--; + } +} + + +/* + * Reuse the SK buffer + */ + +static void uli526x_reuse_skb(struct uli526x_board_info *db, struct sk_buff * skb) +{ + struct rx_desc *rxptr = db->rx_insert_ptr; + + if (!(rxptr->rdes0 & cpu_to_le32(0x80000000))) { + rxptr->rx_skb_ptr = skb; + rxptr->rdes2 = cpu_to_le32( pci_map_single(db->pdev, skb->tail, RX_ALLOC_SIZE, PCI_DMA_FROMDEVICE) ); + wmb(); + rxptr->rdes0 = cpu_to_le32(0x80000000); + db->rx_avail_cnt++; + db->rx_insert_ptr = rxptr->next_rx_desc; + } else + ULI526X_DBUG(0, "SK Buffer reuse method error", db->rx_avail_cnt); +} + + +/* + * Initialize transmit/Receive descriptor + * Using Chain structure, and allocate Tx/Rx buffer + */ + +static void uli526x_descriptor_init(struct uli526x_board_info *db, unsigned long ioaddr) +{ + struct tx_desc *tmp_tx; + struct rx_desc *tmp_rx; + unsigned char *tmp_buf; + dma_addr_t tmp_tx_dma, tmp_rx_dma; + dma_addr_t tmp_buf_dma; + int i; + + ULI526X_DBUG(0, "uli526x_descriptor_init()", 0); + + /* tx descriptor start pointer */ + db->tx_insert_ptr = db->first_tx_desc; + db->tx_remove_ptr = db->first_tx_desc; + outl(db->first_tx_desc_dma, ioaddr + DCR4); /* TX DESC address */ + + /* rx descriptor start pointer */ + db->first_rx_desc = (void *)db->first_tx_desc + sizeof(struct tx_desc) * TX_DESC_CNT; + db->first_rx_desc_dma = db->first_tx_desc_dma + sizeof(struct tx_desc) * TX_DESC_CNT; + db->rx_insert_ptr = db->first_rx_desc; + db->rx_ready_ptr = db->first_rx_desc; + outl(db->first_rx_desc_dma, ioaddr + DCR3); /* RX DESC address */ + + /* Init Transmit chain */ + tmp_buf = db->buf_pool_start; + tmp_buf_dma = db->buf_pool_dma_start; + tmp_tx_dma = db->first_tx_desc_dma; + for (tmp_tx = db->first_tx_desc, i = 0; i < TX_DESC_CNT; i++, tmp_tx++) { + tmp_tx->tx_buf_ptr = tmp_buf; + tmp_tx->tdes0 = cpu_to_le32(0); + tmp_tx->tdes1 = cpu_to_le32(0x81000000); /* IC, chain */ + tmp_tx->tdes2 = cpu_to_le32(tmp_buf_dma); + tmp_tx_dma += sizeof(struct tx_desc); + tmp_tx->tdes3 = cpu_to_le32(tmp_tx_dma); + tmp_tx->next_tx_desc = tmp_tx + 1; + tmp_buf = tmp_buf + TX_BUF_ALLOC; + tmp_buf_dma = tmp_buf_dma + TX_BUF_ALLOC; + } + (--tmp_tx)->tdes3 = cpu_to_le32(db->first_tx_desc_dma); + tmp_tx->next_tx_desc = db->first_tx_desc; + + /* Init Receive descriptor chain */ + tmp_rx_dma=db->first_rx_desc_dma; + for (tmp_rx = db->first_rx_desc, i = 0; i < RX_DESC_CNT; i++, tmp_rx++) { + tmp_rx->rdes0 = cpu_to_le32(0); + tmp_rx->rdes1 = cpu_to_le32(0x01000600); + tmp_rx_dma += sizeof(struct rx_desc); + tmp_rx->rdes3 = cpu_to_le32(tmp_rx_dma); + tmp_rx->next_rx_desc = tmp_rx + 1; + } + (--tmp_rx)->rdes3 = cpu_to_le32(db->first_rx_desc_dma); + tmp_rx->next_rx_desc = db->first_rx_desc; + + /* pre-allocate Rx buffer */ + allocate_rx_buffer(db); +} + + +/* + * Update CR6 value + * Firstly stop ULI526X, then written value and start + */ + +static void update_cr6(u32 cr6_data, unsigned long ioaddr) +{ + + outl(cr6_data, ioaddr + DCR6); + udelay(5); +} + + +/* + * Send a setup frame for M5261/M5263 + * This setup frame initialize ULI526X address filter mode + */ + +static void send_filter_frame(struct net_device *dev, int mc_cnt) +{ + struct uli526x_board_info *db = netdev_priv(dev); + struct dev_mc_list *mcptr; + struct tx_desc *txptr; + u16 * addrptr; + u32 * suptr; + int i; + + ULI526X_DBUG(0, "send_filter_frame()", 0); + + txptr = db->tx_insert_ptr; + suptr = (u32 *) txptr->tx_buf_ptr; + + /* Node address */ + addrptr = (u16 *) dev->dev_addr; + *suptr++ = addrptr[0]; + *suptr++ = addrptr[1]; + *suptr++ = addrptr[2]; + + /* broadcast address */ + *suptr++ = 0xffff; + *suptr++ = 0xffff; + *suptr++ = 0xffff; + + /* fit the multicast address */ + for (mcptr = dev->mc_list, i = 0; i < mc_cnt; i++, mcptr = mcptr->next) { + addrptr = (u16 *) mcptr->dmi_addr; + *suptr++ = addrptr[0]; + *suptr++ = addrptr[1]; + *suptr++ = addrptr[2]; + } + + for (; i<14; i++) { + *suptr++ = 0xffff; + *suptr++ = 0xffff; + *suptr++ = 0xffff; + } + + /* prepare the setup frame */ + db->tx_insert_ptr = txptr->next_tx_desc; + txptr->tdes1 = cpu_to_le32(0x890000c0); + + /* Resource Check and Send the setup packet */ + if (db->tx_packet_cnt < TX_DESC_CNT) { + /* Resource Empty */ + db->tx_packet_cnt++; + txptr->tdes0 = cpu_to_le32(0x80000000); + update_cr6(db->cr6_data | 0x2000, dev->base_addr); + outl(0x1, dev->base_addr + DCR1); /* Issue Tx polling */ + update_cr6(db->cr6_data, dev->base_addr); + dev->trans_start = jiffies; + } else + printk(KERN_ERR DRV_NAME ": No Tx resource - Send_filter_frame!\n"); +} + + +/* + * Allocate rx buffer, + * As possible as allocate maxiumn Rx buffer + */ + +static void allocate_rx_buffer(struct uli526x_board_info *db) +{ + struct rx_desc *rxptr; + struct sk_buff *skb; + + rxptr = db->rx_insert_ptr; + + while(db->rx_avail_cnt < RX_DESC_CNT) { + if ( ( skb = dev_alloc_skb(RX_ALLOC_SIZE) ) == NULL ) + break; + rxptr->rx_skb_ptr = skb; /* FIXME (?) */ + rxptr->rdes2 = cpu_to_le32( pci_map_single(db->pdev, skb->tail, RX_ALLOC_SIZE, PCI_DMA_FROMDEVICE) ); + wmb(); + rxptr->rdes0 = cpu_to_le32(0x80000000); + rxptr = rxptr->next_rx_desc; + db->rx_avail_cnt++; + } + + db->rx_insert_ptr = rxptr; +} + + +/* + * Read one word data from the serial ROM + */ + +static u16 read_srom_word(long ioaddr, int offset) +{ + int i; + u16 srom_data = 0; + long cr9_ioaddr = ioaddr + DCR9; + + outl(CR9_SROM_READ, cr9_ioaddr); + outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr); + + /* Send the Read Command 110b */ + SROM_CLK_WRITE(SROM_DATA_1, cr9_ioaddr); + SROM_CLK_WRITE(SROM_DATA_1, cr9_ioaddr); + SROM_CLK_WRITE(SROM_DATA_0, cr9_ioaddr); + + /* Send the offset */ + for (i = 5; i >= 0; i--) { + srom_data = (offset & (1 << i)) ? SROM_DATA_1 : SROM_DATA_0; + SROM_CLK_WRITE(srom_data, cr9_ioaddr); + } + + outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr); + + for (i = 16; i > 0; i--) { + outl(CR9_SROM_READ | CR9_SRCS | CR9_SRCLK, cr9_ioaddr); + udelay(5); + srom_data = (srom_data << 1) | ((inl(cr9_ioaddr) & CR9_CRDOUT) ? 1 : 0); + outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr); + udelay(5); + } + + outl(CR9_SROM_READ, cr9_ioaddr); + return srom_data; +} + + +/* + * Auto sense the media mode + */ + +static u8 uli526x_sense_speed(struct uli526x_board_info * db) +{ + u8 ErrFlag = 0; + u16 phy_mode; + + phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id); + phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id); + + if ( (phy_mode & 0x24) == 0x24 ) { + + phy_mode = ((phy_read(db->ioaddr, db->phy_addr, 5, db->chip_id) & 0x01e0)<<7); + if(phy_mode&0x8000) + phy_mode = 0x8000; + else if(phy_mode&0x4000) + phy_mode = 0x4000; + else if(phy_mode&0x2000) + phy_mode = 0x2000; + else + phy_mode = 0x1000; + + /* printk(DRV_NAME ": Phy_mode %x ",phy_mode); */ + switch (phy_mode) { + case 0x1000: db->op_mode = ULI526X_10MHF; break; + case 0x2000: db->op_mode = ULI526X_10MFD; break; + case 0x4000: db->op_mode = ULI526X_100MHF; break; + case 0x8000: db->op_mode = ULI526X_100MFD; break; + default: db->op_mode = ULI526X_10MHF; ErrFlag = 1; break; + } + } else { + db->op_mode = ULI526X_10MHF; + ULI526X_DBUG(0, "Link Failed :", phy_mode); + ErrFlag = 1; + } + + return ErrFlag; +} + + +/* + * Set 10/100 phyxcer capability + * AUTO mode : phyxcer register4 is NIC capability + * Force mode: phyxcer register4 is the force media + */ + +static void uli526x_set_phyxcer(struct uli526x_board_info *db) +{ + u16 phy_reg; + + /* Phyxcer capability setting */ + phy_reg = phy_read(db->ioaddr, db->phy_addr, 4, db->chip_id) & ~0x01e0; + + if (db->media_mode & ULI526X_AUTO) { + /* AUTO Mode */ + phy_reg |= db->PHY_reg4; + } else { + /* Force Mode */ + switch(db->media_mode) { + case ULI526X_10MHF: phy_reg |= 0x20; break; + case ULI526X_10MFD: phy_reg |= 0x40; break; + case ULI526X_100MHF: phy_reg |= 0x80; break; + case ULI526X_100MFD: phy_reg |= 0x100; break; + } + + } + + /* Write new capability to Phyxcer Reg4 */ + if ( !(phy_reg & 0x01e0)) { + phy_reg|=db->PHY_reg4; + db->media_mode|=ULI526X_AUTO; + } + phy_write(db->ioaddr, db->phy_addr, 4, phy_reg, db->chip_id); + + /* Restart Auto-Negotiation */ + phy_write(db->ioaddr, db->phy_addr, 0, 0x1200, db->chip_id); + udelay(50); +} + + +/* + * Process op-mode + AUTO mode : PHY controller in Auto-negotiation Mode + * Force mode: PHY controller in force mode with HUB + * N-way force capability with SWITCH + */ + +static void uli526x_process_mode(struct uli526x_board_info *db) +{ + u16 phy_reg; + + /* Full Duplex Mode Check */ + if (db->op_mode & 0x4) + db->cr6_data |= CR6_FDM; /* Set Full Duplex Bit */ + else + db->cr6_data &= ~CR6_FDM; /* Clear Full Duplex Bit */ + + update_cr6(db->cr6_data, db->ioaddr); + + /* 10/100M phyxcer force mode need */ + if ( !(db->media_mode & 0x8)) { + /* Forece Mode */ + phy_reg = phy_read(db->ioaddr, db->phy_addr, 6, db->chip_id); + if ( !(phy_reg & 0x1) ) { + /* parter without N-Way capability */ + phy_reg = 0x0; + switch(db->op_mode) { + case ULI526X_10MHF: phy_reg = 0x0; break; + case ULI526X_10MFD: phy_reg = 0x100; break; + case ULI526X_100MHF: phy_reg = 0x2000; break; + case ULI526X_100MFD: phy_reg = 0x2100; break; + } + phy_write(db->ioaddr, db->phy_addr, 0, phy_reg, db->chip_id); + phy_write(db->ioaddr, db->phy_addr, 0, phy_reg, db->chip_id); + } + } +} + + +/* + * Write a word to Phy register + */ + +static void phy_write(unsigned long iobase, u8 phy_addr, u8 offset, u16 phy_data, u32 chip_id) +{ + u16 i; + unsigned long ioaddr; + + if(chip_id == PCI_ULI5263_ID) + { + phy_writeby_cr10(iobase, phy_addr, offset, phy_data); + return; + } + /* M5261/M5263 Chip */ + ioaddr = iobase + DCR9; + + /* Send 33 synchronization clock to Phy controller */ + for (i = 0; i < 35; i++) + phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + + /* Send start command(01) to Phy */ + phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); + phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + + /* Send write command(01) to Phy */ + phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); + phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + + /* Send Phy address */ + for (i = 0x10; i > 0; i = i >> 1) + phy_write_1bit(ioaddr, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); + + /* Send register address */ + for (i = 0x10; i > 0; i = i >> 1) + phy_write_1bit(ioaddr, offset & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); + + /* written trasnition */ + phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); + + /* Write a word data to PHY controller */ + for ( i = 0x8000; i > 0; i >>= 1) + phy_write_1bit(ioaddr, phy_data & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); + +} + + +/* + * Read a word data from phy register + */ + +static u16 phy_read(unsigned long iobase, u8 phy_addr, u8 offset, u32 chip_id) +{ + int i; + u16 phy_data; + unsigned long ioaddr; + + if(chip_id == PCI_ULI5263_ID) + return phy_readby_cr10(iobase, phy_addr, offset); + /* M5261/M5263 Chip */ + ioaddr = iobase + DCR9; + + /* Send 33 synchronization clock to Phy controller */ + for (i = 0; i < 35; i++) + phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + + /* Send start command(01) to Phy */ + phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); + phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + + /* Send read command(10) to Phy */ + phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); + + /* Send Phy address */ + for (i = 0x10; i > 0; i = i >> 1) + phy_write_1bit(ioaddr, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); + + /* Send register address */ + for (i = 0x10; i > 0; i = i >> 1) + phy_write_1bit(ioaddr, offset & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); + + /* Skip transition state */ + phy_read_1bit(ioaddr, chip_id); + + /* read 16bit data */ + for (phy_data = 0, i = 0; i < 16; i++) { + phy_data <<= 1; + phy_data |= phy_read_1bit(ioaddr, chip_id); + } + + return phy_data; +} + +static u16 phy_readby_cr10(unsigned long iobase, u8 phy_addr, u8 offset) +{ + unsigned long ioaddr,cr10_value; + + ioaddr = iobase + DCR10; + cr10_value = phy_addr; + cr10_value = (cr10_value<<5) + offset; + cr10_value = (cr10_value<<16) + 0x08000000; + outl(cr10_value,ioaddr); + udelay(1); + while(1) + { + cr10_value = inl(ioaddr); + if(cr10_value&0x10000000) + break; + } + return (cr10_value&0x0ffff); +} + +static void phy_writeby_cr10(unsigned long iobase, u8 phy_addr, u8 offset, u16 phy_data) +{ + unsigned long ioaddr,cr10_value; + + ioaddr = iobase + DCR10; + cr10_value = phy_addr; + cr10_value = (cr10_value<<5) + offset; + cr10_value = (cr10_value<<16) + 0x04000000 + phy_data; + outl(cr10_value,ioaddr); + udelay(1); +} +/* + * Write one bit data to Phy Controller + */ + +static void phy_write_1bit(unsigned long ioaddr, u32 phy_data, u32 chip_id) +{ + outl(phy_data , ioaddr); /* MII Clock Low */ + udelay(1); + outl(phy_data | MDCLKH, ioaddr); /* MII Clock High */ + udelay(1); + outl(phy_data , ioaddr); /* MII Clock Low */ + udelay(1); +} + + +/* + * Read one bit phy data from PHY controller + */ + +static u16 phy_read_1bit(unsigned long ioaddr, u32 chip_id) +{ + u16 phy_data; + + outl(0x50000 , ioaddr); + udelay(1); + phy_data = ( inl(ioaddr) >> 19 ) & 0x1; + outl(0x40000 , ioaddr); + udelay(1); + + return phy_data; +} + + +static struct pci_device_id uli526x_pci_tbl[] = { + { 0x10B9, 0x5261, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PCI_ULI5261_ID }, + { 0x10B9, 0x5263, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PCI_ULI5263_ID }, + { 0, } +}; +MODULE_DEVICE_TABLE(pci, uli526x_pci_tbl); + + +static struct pci_driver uli526x_driver = { + .name = "uli526x", + .id_table = uli526x_pci_tbl, + .probe = uli526x_init_one, + .remove = __devexit_p(uli526x_remove_one), +}; + +MODULE_AUTHOR("Peer Chen, peer.chen@uli.com.tw"); +MODULE_DESCRIPTION("ULi M5261/M5263 fast ethernet driver"); +MODULE_LICENSE("GPL"); + +MODULE_PARM(debug, "i"); +MODULE_PARM(mode, "i"); +MODULE_PARM(cr6set, "i"); +MODULE_PARM_DESC(debug, "ULi M5261/M5263 enable debugging (0-1)"); +MODULE_PARM_DESC(mode, "ULi M5261/M5263: Bit 0: 10/100Mbps, bit 2: duplex, bit 8: HomePNA"); + +/* Description: + * when user used insmod to add module, system invoked init_module() + * to register the services. + */ + +static int __init uli526x_init_module(void) +{ + int rc; + + printk(version); + printed_version = 1; + + ULI526X_DBUG(0, "init_module() ", debug); + + if (debug) + uli526x_debug = debug; /* set debug flag */ + if (cr6set) + uli526x_cr6_user_set = cr6set; + + switch(mode) { + case ULI526X_10MHF: + case ULI526X_100MHF: + case ULI526X_10MFD: + case ULI526X_100MFD: + uli526x_media_mode = mode; + break; + default:uli526x_media_mode = ULI526X_AUTO; + break; + } + + rc = pci_module_init(&uli526x_driver); + if (rc < 0) + return rc; + + return 0; +} + + +/* + * Description: + * when user used rmmod to delete module, system invoked clean_module() + * to un-register all registered services. + */ + +static void __exit uli526x_cleanup_module(void) +{ + ULI526X_DBUG(0, "uli526x_clean_module() ", debug); + pci_unregister_driver(&uli526x_driver); +} + +module_init(uli526x_init_module); +module_exit(uli526x_cleanup_module); |