diff options
Diffstat (limited to 'drivers/usb')
32 files changed, 329 insertions, 178 deletions
diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c index e12c5be..f50aaf2 100644 --- a/drivers/usb/core/message.c +++ b/drivers/usb/core/message.c @@ -431,7 +431,7 @@ nomem: * (2) error, where io->status is a negative errno value. The number * of io->bytes transferred before the error is usually less * than requested, and can be nonzero. - * (3) cancelation, a type of error with status -ECONNRESET that + * (3) cancellation, a type of error with status -ECONNRESET that * is initiated by usb_sg_cancel(). * * When this function returns, all memory allocated through usb_sg_init() or @@ -1282,7 +1282,7 @@ static void release_interface(struct device *dev) * bus rwsem; usb device driver probe() methods cannot use this routine. * * Returns zero on success, or else the status code returned by the - * underlying call that failed. On succesful completion, each interface + * underlying call that failed. On successful completion, each interface * in the original device configuration has been destroyed, and each one * in the new configuration has been probed by all relevant usb device * drivers currently known to the kernel. diff --git a/drivers/usb/core/urb.c b/drivers/usb/core/urb.c index 1697215..0faf18d 100644 --- a/drivers/usb/core/urb.c +++ b/drivers/usb/core/urb.c @@ -121,7 +121,7 @@ struct urb * usb_get_urb(struct urb *urb) * describing that request to the USB subsystem. Request completion will * be indicated later, asynchronously, by calling the completion handler. * The three types of completion are success, error, and unlink - * (a software-induced fault, also called "request cancelation"). + * (a software-induced fault, also called "request cancellation"). * * URBs may be submitted in interrupt context. * @@ -170,7 +170,7 @@ struct urb * usb_get_urb(struct urb *urb) * As of Linux 2.6, all USB endpoint transfer queues support depths greater * than one. This was previously a HCD-specific behavior, except for ISO * transfers. Non-isochronous endpoint queues are inactive during cleanup - * after faults (transfer errors or cancelation). + * after faults (transfer errors or cancellation). * * Reserved Bandwidth Transfers: * @@ -395,7 +395,7 @@ int usb_submit_urb(struct urb *urb, int mem_flags) * * This routine cancels an in-progress request. URBs complete only * once per submission, and may be canceled only once per submission. - * Successful cancelation means the requests's completion handler will + * Successful cancellation means the requests's completion handler will * be called with a status code indicating that the request has been * canceled (rather than any other code) and will quickly be removed * from host controller data structures. diff --git a/drivers/usb/gadget/ether.c b/drivers/usb/gadget/ether.c index 3993156..3f783cb 100644 --- a/drivers/usb/gadget/ether.c +++ b/drivers/usb/gadget/ether.c @@ -569,7 +569,7 @@ static const struct usb_cdc_ether_desc ether_desc = { /* include the status endpoint if we can, even where it's optional. * use wMaxPacketSize big enough to fit CDC_NOTIFY_SPEED_CHANGE in one - * packet, to simplify cancelation; and a big transfer interval, to + * packet, to simplify cancellation; and a big transfer interval, to * waste less bandwidth. * * some drivers (like Linux 2.4 cdc-ether!) "need" it to exist even diff --git a/drivers/usb/gadget/inode.c b/drivers/usb/gadget/inode.c index 2cff67c..1e5e6dd 100644 --- a/drivers/usb/gadget/inode.c +++ b/drivers/usb/gadget/inode.c @@ -275,7 +275,7 @@ static const char *CHIP; * * After opening, configure non-control endpoints. Then use normal * stream read() and write() requests; and maybe ioctl() to get more - * precise FIFO status when recovering from cancelation. + * precise FIFO status when recovering from cancellation. */ static void epio_complete (struct usb_ep *ep, struct usb_request *req) diff --git a/drivers/usb/gadget/lh7a40x_udc.c b/drivers/usb/gadget/lh7a40x_udc.c index 0def9f7..df75ab6 100644 --- a/drivers/usb/gadget/lh7a40x_udc.c +++ b/drivers/usb/gadget/lh7a40x_udc.c @@ -705,7 +705,7 @@ void nuke(struct lh7a40x_ep *ep, int status) done(ep, req, status); } - /* Disable IRQ if EP is enabled (has decriptor) */ + /* Disable IRQ if EP is enabled (has descriptor) */ if (ep->desc) pio_irq_disable(ep_index(ep)); } diff --git a/drivers/usb/gadget/serial.c b/drivers/usb/gadget/serial.c index f1762ed..4d591c7 100644 --- a/drivers/usb/gadget/serial.c +++ b/drivers/usb/gadget/serial.c @@ -240,7 +240,7 @@ struct gs_dev { struct usb_ep *dev_notify_ep; /* address of notify endpoint */ struct usb_ep *dev_in_ep; /* address of in endpoint */ struct usb_ep *dev_out_ep; /* address of out endpoint */ - struct usb_endpoint_descriptor /* desciptor of notify ep */ + struct usb_endpoint_descriptor /* descriptor of notify ep */ *dev_notify_ep_desc; struct usb_endpoint_descriptor /* descriptor of in endpoint */ *dev_in_ep_desc; diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 84d2b93..bc69bd7 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -346,6 +346,22 @@ ehci_reboot (struct notifier_block *self, unsigned long code, void *null) return 0; } +static void ehci_port_power (struct ehci_hcd *ehci, int is_on) +{ + unsigned port; + + if (!HCS_PPC (ehci->hcs_params)) + return; + + ehci_dbg (ehci, "...power%s ports...\n", is_on ? "up" : "down"); + for (port = HCS_N_PORTS (ehci->hcs_params); port > 0; ) + (void) ehci_hub_control(ehci_to_hcd(ehci), + is_on ? SetPortFeature : ClearPortFeature, + USB_PORT_FEAT_POWER, + port--, NULL, 0); + msleep(20); +} + /* called by khubd or root hub init threads */ @@ -362,8 +378,10 @@ static int ehci_hc_reset (struct usb_hcd *hcd) dbg_hcs_params (ehci, "reset"); dbg_hcc_params (ehci, "reset"); + /* cache this readonly data; minimize chip reads */ + ehci->hcs_params = readl (&ehci->caps->hcs_params); + #ifdef CONFIG_PCI - /* EHCI 0.96 and later may have "extended capabilities" */ if (hcd->self.controller->bus == &pci_bus_type) { struct pci_dev *pdev = to_pci_dev(hcd->self.controller); @@ -383,9 +401,30 @@ static int ehci_hc_reset (struct usb_hcd *hcd) break; } + /* optional debug port, normally in the first BAR */ + temp = pci_find_capability (pdev, 0x0a); + if (temp) { + pci_read_config_dword(pdev, temp, &temp); + temp >>= 16; + if ((temp & (3 << 13)) == (1 << 13)) { + temp &= 0x1fff; + ehci->debug = hcd->regs + temp; + temp = readl (&ehci->debug->control); + ehci_info (ehci, "debug port %d%s\n", + HCS_DEBUG_PORT(ehci->hcs_params), + (temp & DBGP_ENABLED) + ? " IN USE" + : ""); + if (!(temp & DBGP_ENABLED)) + ehci->debug = NULL; + } + } + temp = HCC_EXT_CAPS (readl (&ehci->caps->hcc_params)); } else temp = 0; + + /* EHCI 0.96 and later may have "extended capabilities" */ while (temp && count--) { u32 cap; @@ -414,8 +453,7 @@ static int ehci_hc_reset (struct usb_hcd *hcd) ehci_reset (ehci); #endif - /* cache this readonly data; minimize PCI reads */ - ehci->hcs_params = readl (&ehci->caps->hcs_params); + ehci_port_power (ehci, 0); /* at least the Genesys GL880S needs fixup here */ temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params); @@ -657,16 +695,11 @@ done2: static void ehci_stop (struct usb_hcd *hcd) { struct ehci_hcd *ehci = hcd_to_ehci (hcd); - u8 rh_ports, port; ehci_dbg (ehci, "stop\n"); /* Turn off port power on all root hub ports. */ - rh_ports = HCS_N_PORTS (ehci->hcs_params); - for (port = 1; port <= rh_ports; port++) - (void) ehci_hub_control(hcd, - ClearPortFeature, USB_PORT_FEAT_POWER, - port, NULL, 0); + ehci_port_power (ehci, 0); /* no more interrupts ... */ del_timer_sync (&ehci->watchdog); @@ -748,7 +781,6 @@ static int ehci_resume (struct usb_hcd *hcd) unsigned port; struct usb_device *root = hcd->self.root_hub; int retval = -EINVAL; - int powerup = 0; // maybe restore (PCI) FLADJ @@ -766,8 +798,6 @@ static int ehci_resume (struct usb_hcd *hcd) up (&hcd->self.root_hub->serialize); break; } - if ((status & PORT_POWER) == 0) - powerup = 1; if (!root->children [port]) continue; dbg_port (ehci, __FUNCTION__, port + 1, status); @@ -794,16 +824,9 @@ static int ehci_resume (struct usb_hcd *hcd) retval = ehci_start (hcd); /* here we "know" root ports should always stay powered; - * but some controllers may lost all power. + * but some controllers may lose all power. */ - if (powerup) { - ehci_dbg (ehci, "...powerup ports...\n"); - for (port = HCS_N_PORTS (ehci->hcs_params); port > 0; ) - (void) ehci_hub_control(hcd, - SetPortFeature, USB_PORT_FEAT_POWER, - port--, NULL, 0); - msleep(20); - } + ehci_port_power (ehci, 1); } return retval; diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c index 2373537..02fefab 100644 --- a/drivers/usb/host/ehci-hub.c +++ b/drivers/usb/host/ehci-hub.c @@ -281,6 +281,8 @@ ehci_hub_descriptor ( temp = 0x0008; /* per-port overcurrent reporting */ if (HCS_PPC (ehci->hcs_params)) temp |= 0x0001; /* per-port power control */ + else + temp |= 0x0002; /* no power switching */ #if 0 // re-enable when we support USB_PORT_FEAT_INDICATOR below. if (HCS_INDICATOR (ehci->hcs_params)) diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h index e763a83..4df4982 100644 --- a/drivers/usb/host/ehci.h +++ b/drivers/usb/host/ehci.h @@ -47,6 +47,12 @@ struct ehci_stats { #define EHCI_MAX_ROOT_PORTS 15 /* see HCS_N_PORTS */ struct ehci_hcd { /* one per controller */ + /* glue to PCI and HCD framework */ + struct ehci_caps __iomem *caps; + struct ehci_regs __iomem *regs; + struct ehci_dbg_port __iomem *debug; + + __u32 hcs_params; /* cached register copy */ spinlock_t lock; /* async schedule support */ @@ -84,11 +90,6 @@ struct ehci_hcd { /* one per controller */ unsigned is_tdi_rh_tt:1; /* TDI roothub with TT */ - /* glue to PCI and HCD framework */ - struct ehci_caps __iomem *caps; - struct ehci_regs __iomem *regs; - __u32 hcs_params; /* cached register copy */ - /* irq statistics */ #ifdef EHCI_STATS struct ehci_stats stats; @@ -165,7 +166,7 @@ struct ehci_caps { /* these fields are specified as 8 and 16 bit registers, * but some hosts can't perform 8 or 16 bit PCI accesses. */ - u32 hc_capbase; + u32 hc_capbase; #define HC_LENGTH(p) (((p)>>00)&0x00ff) /* bits 7:0 */ #define HC_VERSION(p) (((p)>>16)&0xffff) /* bits 31:16 */ u32 hcs_params; /* HCSPARAMS - offset 0x4 */ @@ -273,7 +274,7 @@ struct ehci_dbg_port { #define DBGP_ENABLED (1<<28) #define DBGP_DONE (1<<16) #define DBGP_INUSE (1<<10) -#define DBGP_ERRCODE(x) (((x)>>7)&0x0f) +#define DBGP_ERRCODE(x) (((x)>>7)&0x07) # define DBGP_ERR_BAD 1 # define DBGP_ERR_SIGNAL 2 #define DBGP_ERROR (1<<6) @@ -282,11 +283,11 @@ struct ehci_dbg_port { #define DBGP_LEN(x) (((x)>>0)&0x0f) u32 pids; #define DBGP_PID_GET(x) (((x)>>16)&0xff) -#define DBGP_PID_SET(data,tok) (((data)<<8)|(tok)); +#define DBGP_PID_SET(data,tok) (((data)<<8)|(tok)) u32 data03; u32 data47; u32 address; -#define DBGP_EPADDR(dev,ep) (((dev)<<8)|(ep)); +#define DBGP_EPADDR(dev,ep) (((dev)<<8)|(ep)) } __attribute__ ((packed)); /*-------------------------------------------------------------------------*/ diff --git a/drivers/usb/host/hc_crisv10.c b/drivers/usb/host/hc_crisv10.c index 376f8a0..d9883d7 100644 --- a/drivers/usb/host/hc_crisv10.c +++ b/drivers/usb/host/hc_crisv10.c @@ -4329,7 +4329,7 @@ static int __init etrax_usb_hc_init(void) bus->bus_name="ETRAX 100LX"; bus->hcpriv = hc; - /* Initalize RH to the default address. + /* Initialize RH to the default address. And make sure that we have no status change indication */ hc->rh.numports = 2; /* The RH has two ports */ hc->rh.devnum = 1; diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c index d309e29..a374b76 100644 --- a/drivers/usb/host/sl811-hcd.c +++ b/drivers/usb/host/sl811-hcd.c @@ -134,7 +134,7 @@ static void port_power(struct sl811 *sl811, int is_on) /* This is a PIO-only HCD. Queueing appends URBs to the endpoint's queue, * and may start I/O. Endpoint queues are scanned during completion irq - * handlers (one per packet: ACK, NAK, faults, etc) and urb cancelation. + * handlers (one per packet: ACK, NAK, faults, etc) and urb cancellation. * * Using an external DMA engine to copy a packet at a time could work, * though setup/teardown costs may be too big to make it worthwhile. @@ -738,7 +738,7 @@ retry: } #endif - /* port status seems wierd until after reset, so + /* port status seems weird until after reset, so * force the reset and make khubd clean up later. */ sl811->port1 |= (1 << USB_PORT_FEAT_C_CONNECTION) diff --git a/drivers/usb/image/mdc800.c b/drivers/usb/image/mdc800.c index 5791723..a330a4b 100644 --- a/drivers/usb/image/mdc800.c +++ b/drivers/usb/image/mdc800.c @@ -23,7 +23,7 @@ * * * The driver brings the USB functions of the MDC800 to Linux. - * To use the Camera you must support the USB Protocoll of the camera + * To use the Camera you must support the USB Protocol of the camera * to the Kernel Node. * The Driver uses a misc device Node. Create it with : * mknod /dev/mustek c 180 32 diff --git a/drivers/usb/input/aiptek.c b/drivers/usb/input/aiptek.c index 2d76be6..94ce2a9 100644 --- a/drivers/usb/input/aiptek.c +++ b/drivers/usb/input/aiptek.c @@ -386,7 +386,7 @@ static int aiptek_convert_from_2s_complement(unsigned char c) * convention above.) I therefore have taken over REL_MISC and ABS_MISC * (for relative and absolute reports, respectively) for communicating * Proximity. Why two events? I thought it interesting to know if the - * Proximity event occured while the tablet was in absolute or relative + * Proximity event occurred while the tablet was in absolute or relative * mode. * * Other tablets use the notion of a certain minimum stylus pressure diff --git a/drivers/usb/input/mtouchusb.c b/drivers/usb/input/mtouchusb.c index 6b45a66..ab1a2a3 100644 --- a/drivers/usb/input/mtouchusb.c +++ b/drivers/usb/input/mtouchusb.c @@ -32,7 +32,7 @@ * Changed reset from standard USB dev reset to vendor reset * Changed data sent to host from compensated to raw coordinates * Eliminated vendor/product module params - * Performed multiple successfull tests with an EXII-5010UC + * Performed multiple successful tests with an EXII-5010UC * * 1.5 02/27/2005 ddstreet@ieee.org * Added module parameter to select raw or hw-calibrated coordinate reporting diff --git a/drivers/usb/media/ov511.c b/drivers/usb/media/ov511.c index d605182..036c485 100644 --- a/drivers/usb/media/ov511.c +++ b/drivers/usb/media/ov511.c @@ -5041,7 +5041,7 @@ ov6xx0_configure(struct usb_ov511 *ov) { OV511_I2C_BUS, 0x2a, 0x04 }, /* Disable framerate adjust */ // { OV511_I2C_BUS, 0x2b, 0xac }, /* Framerate; Set 2a[7] first */ { OV511_I2C_BUS, 0x2d, 0x99 }, - { OV511_I2C_BUS, 0x33, 0xa0 }, /* Color Procesing Parameter */ + { OV511_I2C_BUS, 0x33, 0xa0 }, /* Color Processing Parameter */ { OV511_I2C_BUS, 0x34, 0xd2 }, /* Max A/D range */ { OV511_I2C_BUS, 0x38, 0x8b }, { OV511_I2C_BUS, 0x39, 0x40 }, diff --git a/drivers/usb/media/pwc/pwc-ctrl.c b/drivers/usb/media/pwc/pwc-ctrl.c index 42352f5..42ec468 100644 --- a/drivers/usb/media/pwc/pwc-ctrl.c +++ b/drivers/usb/media/pwc/pwc-ctrl.c @@ -1100,7 +1100,7 @@ static inline int pwc_mpt_set_angle(struct pwc_device *pdev, int pan, int tilt) unsigned char buf[4]; /* set new relative angle; angles are expressed in degrees * 100, - but cam as .5 degree resolution, hence devide by 200. Also + but cam as .5 degree resolution, hence divide by 200. Also the angle must be multiplied by 64 before it's send to the cam (??) */ diff --git a/drivers/usb/media/pwc/pwc-if.c b/drivers/usb/media/pwc/pwc-if.c index c53e226..cca47f4 100644 --- a/drivers/usb/media/pwc/pwc-if.c +++ b/drivers/usb/media/pwc/pwc-if.c @@ -272,7 +272,7 @@ static int pwc_allocate_buffers(struct pwc_device *pdev) return -ENXIO; } #endif - /* Allocate Isochronuous pipe buffers */ + /* Allocate Isochronous pipe buffers */ for (i = 0; i < MAX_ISO_BUFS; i++) { if (pdev->sbuf[i].data == NULL) { kbuf = kmalloc(ISO_BUFFER_SIZE, GFP_KERNEL); @@ -850,7 +850,7 @@ static int pwc_isoc_init(struct pwc_device *pdev) if (pdev->vmax_packet_size < 0 || pdev->vmax_packet_size > ISO_MAX_FRAME_SIZE) { Err("Failed to find packet size for video endpoint in current alternate setting.\n"); - return -ENFILE; /* Odd error, that should be noticable */ + return -ENFILE; /* Odd error, that should be noticeable */ } /* Set alternate interface */ @@ -2128,7 +2128,7 @@ static int __init usb_pwc_init(void) if (leds[1] >= 0) led_off = leds[1]; - /* Big device node whoopla. Basicly, it allows you to assign a + /* Big device node whoopla. Basically, it allows you to assign a device node (/dev/videoX) to a camera, based on its type & serial number. The format is [type[.serialnumber]:]node. diff --git a/drivers/usb/media/pwc/pwc-ioctl.h b/drivers/usb/media/pwc/pwc-ioctl.h index 65805ea..5f9cb08 100644 --- a/drivers/usb/media/pwc/pwc-ioctl.h +++ b/drivers/usb/media/pwc/pwc-ioctl.h @@ -75,7 +75,7 @@ #define PWC_FPS_SNAPSHOT 0x00400000 -/* structure for transfering x & y coordinates */ +/* structure for transferring x & y coordinates */ struct pwc_coord { int x, y; /* guess what */ diff --git a/drivers/usb/misc/legousbtower.c b/drivers/usb/misc/legousbtower.c index dd4580c..7d06105 100644 --- a/drivers/usb/misc/legousbtower.c +++ b/drivers/usb/misc/legousbtower.c @@ -859,7 +859,7 @@ static int tower_probe (struct usb_interface *interface, const struct usb_device info ("udev is NULL."); } - /* allocate memory for our device state and intialize it */ + /* allocate memory for our device state and initialize it */ dev = kmalloc (sizeof(struct lego_usb_tower), GFP_KERNEL); diff --git a/drivers/usb/net/usbnet.c b/drivers/usb/net/usbnet.c index a45ea7c..f6bc6b3 100644 --- a/drivers/usb/net/usbnet.c +++ b/drivers/usb/net/usbnet.c @@ -4071,6 +4071,9 @@ static const struct usb_device_id products [] = { USB_DEVICE (0x8086, 0x07d3), // "blob" bootloader .driver_info = (unsigned long) &blob_info, }, { + USB_DEVICE (0x22b8, 0x600c), // USBNET Motorola E680 + .driver_info = (unsigned long) &linuxdev_info, +}, { // Linux Ethernet/RNDIS gadget on pxa210/25x/26x // e.g. Gumstix, current OpenZaurus, ... USB_DEVICE_VER (0x0525, 0xa4a2, 0x0203, 0x0203), diff --git a/drivers/usb/net/zd1201.c b/drivers/usb/net/zd1201.c index f98cb2a..341ae5f 100644 --- a/drivers/usb/net/zd1201.c +++ b/drivers/usb/net/zd1201.c @@ -183,7 +183,7 @@ static void zd1201_usbtx(struct urb *urb, struct pt_regs *regs) return; } -/* Incomming data */ +/* Incoming data */ static void zd1201_usbrx(struct urb *urb, struct pt_regs *regs) { struct zd1201 *zd = urb->context; @@ -772,7 +772,7 @@ static int zd1201_net_stop(struct net_device *dev) /* RFC 1042 encapsulates Ethernet frames in 802.11 frames by prefixing them with 0xaa, 0xaa, 0x03) followed by a SNAP OID of 0 - (0x00, 0x00, 0x00). Zd requires an additionnal padding, copy + (0x00, 0x00, 0x00). Zd requires an additional padding, copy of ethernet addresses, length of the standard RFC 1042 packet and a command byte (which is nul for tx). @@ -1098,7 +1098,7 @@ static int zd1201_get_range(struct net_device *dev, /* Little bit of magic here: we only get the quality if we poll * for it, and we never get an actual request to trigger such - * a poll. Therefore we 'asume' that the user will soon ask for + * a poll. Therefore we 'assume' that the user will soon ask for * the stats after asking the bssid. */ static int zd1201_get_wap(struct net_device *dev, @@ -1108,7 +1108,7 @@ static int zd1201_get_wap(struct net_device *dev, unsigned char buffer[6]; if (!zd1201_getconfig(zd, ZD1201_RID_COMMSQUALITY, buffer, 6)) { - /* Unfortunatly the quality and noise reported is useless. + /* Unfortunately the quality and noise reported is useless. they seem to be accumulators that increase until you read them, unless we poll on a fixed interval we can't use them diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig index 0c4aa00..bc798ed 100644 --- a/drivers/usb/serial/Kconfig +++ b/drivers/usb/serial/Kconfig @@ -53,6 +53,15 @@ config USB_SERIAL_GENERIC support" be compiled as a module for this driver to be used properly. +config USB_SERIAL_AIRPRIME + tristate "USB AirPrime CDMA Wireless Driver" + depends on USB_SERIAL + help + Say Y here if you want to use a AirPrime CDMA Wireless PC card. + + To compile this driver as a module, choose M here: the + module will be called airprime. + config USB_SERIAL_BELKIN tristate "USB Belkin and Peracom Single Port Serial Driver" depends on USB_SERIAL diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile index b0aac47d..d56ff6d 100644 --- a/drivers/usb/serial/Makefile +++ b/drivers/usb/serial/Makefile @@ -11,6 +11,7 @@ usbserial-obj-$(CONFIG_USB_EZUSB) += ezusb.o usbserial-objs := usb-serial.o generic.o bus.o $(usbserial-obj-y) +obj-$(CONFIG_USB_SERIAL_AIRPRIME) += airprime.o obj-$(CONFIG_USB_SERIAL_BELKIN) += belkin_sa.o obj-$(CONFIG_USB_SERIAL_CP2101) += cp2101.o obj-$(CONFIG_USB_SERIAL_CYBERJACK) += cyberjack.o diff --git a/drivers/usb/serial/airprime.c b/drivers/usb/serial/airprime.c new file mode 100644 index 0000000..a4ce000 --- /dev/null +++ b/drivers/usb/serial/airprime.c @@ -0,0 +1,63 @@ +/* + * AirPrime CDMA Wireless Serial USB driver + * + * Copyright (C) 2005 Greg Kroah-Hartman <gregkh@suse.de> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/tty.h> +#include <linux/module.h> +#include <linux/usb.h> +#include "usb-serial.h" + +static struct usb_device_id id_table [] = { + { USB_DEVICE(0xf3d, 0x0112) }, + { }, +}; +MODULE_DEVICE_TABLE(usb, id_table); + +static struct usb_driver airprime_driver = { + .owner = THIS_MODULE, + .name = "airprime", + .probe = usb_serial_probe, + .disconnect = usb_serial_disconnect, + .id_table = id_table, +}; + +static struct usb_serial_device_type airprime_device = { + .owner = THIS_MODULE, + .name = "airprime", + .id_table = id_table, + .num_interrupt_in = NUM_DONT_CARE, + .num_bulk_in = NUM_DONT_CARE, + .num_bulk_out = NUM_DONT_CARE, + .num_ports = 1, +}; + +static int __init airprime_init(void) +{ + int retval; + + retval = usb_serial_register(&airprime_device); + if (retval) + return retval; + retval = usb_register(&airprime_driver); + if (retval) + usb_serial_deregister(&airprime_device); + return retval; +} + +static void __exit airprime_exit(void) +{ + usb_deregister(&airprime_driver); + usb_serial_deregister(&airprime_device); +} + +module_init(airprime_init); +module_exit(airprime_exit); +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c index d165f42..f34a9bb 100644 --- a/drivers/usb/serial/cypress_m8.c +++ b/drivers/usb/serial/cypress_m8.c @@ -16,6 +16,14 @@ * See http://geocities.com/i0xox0i for information on this driver and the * earthmate usb device. * + * Lonnie Mendez <dignome@gmail.com> + * 4-29-2005 + * Fixed problem where setting or retreiving the serial config would fail with + * EPIPE. Removed CRTS toggling so the driver behaves more like other usbserial + * adapters. Issued new interval of 1ms instead of the default 10ms. As a + * result, transfer speed has been substantially increased. From avg. 850bps to + * avg. 3300bps. initial termios has also been modified. Cleaned up code and + * formatting issues so it is more readable. Replaced the C++ style comments. * * Lonnie Mendez <dignome@gmail.com> * 12-15-2004 @@ -32,12 +40,6 @@ * 10-2003 * Driver first released. * - * - * Long Term TODO: - * Improve transfer speeds - both read/write are somewhat slow - * at this point. - * Improve debugging. Show modem line status with debug output and - * implement filtering for certain data as a module parameter. */ /* Thanks to Neil Whelchel for writing the first cypress m8 implementation for linux. */ @@ -72,11 +74,12 @@ static int debug; #endif static int stats; +static int interval; /* * Version Information */ -#define DRIVER_VERSION "v1.08" +#define DRIVER_VERSION "v1.09" #define DRIVER_AUTHOR "Lonnie Mendez <dignome@gmail.com>, Neil Whelchel <koyama@firstlight.net>" #define DRIVER_DESC "Cypress USB to Serial Driver" @@ -130,7 +133,6 @@ struct cypress_private { char prev_status, diff_status; /* used for TIOCMIWAIT */ /* we pass a pointer to this as the arguement sent to cypress_set_termios old_termios */ struct termios tmp_termios; /* stores the old termios settings */ - char calledfromopen; /* used when issuing lines on open - fixes rts drop bug */ }; /* write buffer structure */ @@ -168,10 +170,8 @@ static void cypress_buf_free(struct cypress_buf *cb); static void cypress_buf_clear(struct cypress_buf *cb); static unsigned int cypress_buf_data_avail(struct cypress_buf *cb); static unsigned int cypress_buf_space_avail(struct cypress_buf *cb); -static unsigned int cypress_buf_put(struct cypress_buf *cb, const char *buf, - unsigned int count); -static unsigned int cypress_buf_get(struct cypress_buf *cb, char *buf, - unsigned int count); +static unsigned int cypress_buf_put(struct cypress_buf *cb, const char *buf, unsigned int count); +static unsigned int cypress_buf_get(struct cypress_buf *cb, char *buf, unsigned int count); static struct usb_serial_device_type cypress_earthmate_device = { @@ -234,14 +234,13 @@ static struct usb_serial_device_type cypress_hidcom_device = { *****************************************************************************/ -/* This function can either set or retreive the current serial line settings */ +/* This function can either set or retrieve the current serial line settings */ static int cypress_serial_control (struct usb_serial_port *port, unsigned baud_mask, int data_bits, int stop_bits, int parity_enable, int parity_type, int reset, int cypress_request_type) { - int i, n_baud_rate = 0, retval = 0; + int new_baudrate = 0, retval = 0, tries = 0; struct cypress_private *priv; - __u8 feature_buffer[5]; - __u8 config; + __u8 feature_buffer[8]; unsigned long flags; dbg("%s", __FUNCTION__); @@ -256,7 +255,8 @@ static int cypress_serial_control (struct usb_serial_port *port, unsigned baud_m * of 57600bps (I have no idea whether DeLorme chose to use the general purpose * firmware or not), if you need to modify this speed setting for your own * project please add your own chiptype and modify the code likewise. The - * Cypress HID->COM device will work successfully up to 115200bps. + * Cypress HID->COM device will work successfully up to 115200bps (but the + * actual throughput is around 3kBps). */ if (baud_mask != priv->cbr_mask) { dbg("%s - baud rate is changing", __FUNCTION__); @@ -265,109 +265,114 @@ static int cypress_serial_control (struct usb_serial_port *port, unsigned baud_m * but are not used with NMEA and SiRF protocols */ if ( (baud_mask == B300) || (baud_mask == B600) ) { - err("%s - failed setting baud rate, unsupported speed (default to 4800)", + err("%s - failed setting baud rate, unsupported speed", __FUNCTION__); - n_baud_rate = 4800; - } else if ( (n_baud_rate = mask_to_rate(baud_mask)) == -1) { - err("%s - failed setting baud rate, unsupported speed (default to 4800)", + new_baudrate = priv->baud_rate; + } else if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) { + err("%s - failed setting baud rate, unsupported speed", __FUNCTION__); - n_baud_rate = 4800; + new_baudrate = priv->baud_rate; } } else if (priv->chiptype == CT_CYPHIDCOM) { - if ( (n_baud_rate = mask_to_rate(baud_mask)) == -1) { - err("%s - failed setting baud rate, unsupported speed (default to 4800)", + if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) { + err("%s - failed setting baud rate, unsupported speed", __FUNCTION__); - n_baud_rate = 4800; + new_baudrate = priv->baud_rate; } } else if (priv->chiptype == CT_GENERIC) { - if ( (n_baud_rate = mask_to_rate(baud_mask)) == -1) { - err("%s - failed setting baud rate, unsupported speed (default to 4800)", + if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) { + err("%s - failed setting baud rate, unsupported speed", __FUNCTION__); - n_baud_rate = 4800; + new_baudrate = priv->baud_rate; } } else { - info("%s - please define your chiptype, using 4800bps default", __FUNCTION__); - n_baud_rate = 4800; + info("%s - please define your chiptype", __FUNCTION__); + new_baudrate = priv->baud_rate; } } else { /* baud rate not changing, keep the old */ - n_baud_rate = priv->baud_rate; + new_baudrate = priv->baud_rate; } - dbg("%s - baud rate is being sent as %d", __FUNCTION__, n_baud_rate); - + dbg("%s - baud rate is being sent as %d", __FUNCTION__, new_baudrate); - /* - * This algorithm accredited to Jiang Jay Zhang... thanks for all the help! - */ - for (i = 0; i < 4; ++i) { - feature_buffer[i] = ( n_baud_rate >> (i*8) & 0xFF ); - } + memset(feature_buffer, 0, 8); + /* fill the feature_buffer with new configuration */ + *((u_int32_t *)feature_buffer) = new_baudrate; - config = 0; // reset config byte - config |= data_bits; // assign data bits in 2 bit space ( max 3 ) + feature_buffer[4] |= data_bits; /* assign data bits in 2 bit space ( max 3 ) */ /* 1 bit gap */ - config |= (stop_bits << 3); // assign stop bits in 1 bit space - config |= (parity_enable << 4); // assign parity flag in 1 bit space - config |= (parity_type << 5); // assign parity type in 1 bit space + feature_buffer[4] |= (stop_bits << 3); /* assign stop bits in 1 bit space */ + feature_buffer[4] |= (parity_enable << 4); /* assign parity flag in 1 bit space */ + feature_buffer[4] |= (parity_type << 5); /* assign parity type in 1 bit space */ /* 1 bit gap */ - config |= (reset << 7); // assign reset at end of byte, 1 bit space - - feature_buffer[4] = config; + feature_buffer[4] |= (reset << 7); /* assign reset at end of byte, 1 bit space */ dbg("%s - device is being sent this feature report:", __FUNCTION__); dbg("%s - %02X - %02X - %02X - %02X - %02X", __FUNCTION__, feature_buffer[0], feature_buffer[1], feature_buffer[2], feature_buffer[3], feature_buffer[4]); + do { retval = usb_control_msg (port->serial->dev, usb_sndctrlpipe(port->serial->dev, 0), HID_REQ_SET_REPORT, USB_DIR_OUT | USB_RECIP_INTERFACE | USB_TYPE_CLASS, - 0x0300, 0, feature_buffer, 5, 500); + 0x0300, 0, feature_buffer, 8, 500); + + if (tries++ >= 3) + break; - if (retval != 5) + if (retval == EPIPE) + usb_clear_halt(port->serial->dev, 0x00); + } while (retval != 8 && retval != ENODEV); + + if (retval != 8) err("%s - failed sending serial line settings - %d", __FUNCTION__, retval); else { spin_lock_irqsave(&priv->lock, flags); - priv->baud_rate = n_baud_rate; + priv->baud_rate = new_baudrate; priv->cbr_mask = baud_mask; - priv->current_config = config; - ++priv->cmd_count; + priv->current_config = feature_buffer[4]; spin_unlock_irqrestore(&priv->lock, flags); } break; case CYPRESS_GET_CONFIG: dbg("%s - retreiving serial line settings", __FUNCTION__); - /* reset values in feature buffer */ - memset(feature_buffer, 0, 5); + /* set initial values in feature buffer */ + memset(feature_buffer, 0, 8); + do { retval = usb_control_msg (port->serial->dev, usb_rcvctrlpipe(port->serial->dev, 0), HID_REQ_GET_REPORT, USB_DIR_IN | USB_RECIP_INTERFACE | USB_TYPE_CLASS, - 0x0300, 0, feature_buffer, 5, 500); + 0x0300, 0, feature_buffer, 8, 500); + + if (tries++ >= 3) + break; + + if (retval == EPIPE) + usb_clear_halt(port->serial->dev, 0x00); + } while (retval != 5 && retval != ENODEV); + if (retval != 5) { err("%s - failed to retreive serial line settings - %d", __FUNCTION__, retval); return retval; } else { spin_lock_irqsave(&priv->lock, flags); + /* store the config in one byte, and later use bit masks to check values */ priv->current_config = feature_buffer[4]; - /* reverse the process above to get the baud_mask value */ - n_baud_rate = 0; // reset bits - for (i = 0; i < 4; ++i) { - n_baud_rate |= ( feature_buffer[i] << (i*8) ); - } + priv->baud_rate = *((u_int32_t *)feature_buffer); - priv->baud_rate = n_baud_rate; - if ( (priv->cbr_mask = rate_to_mask(n_baud_rate)) == 0x40) + if ( (priv->cbr_mask = rate_to_mask(priv->baud_rate)) == 0x40) dbg("%s - failed setting the baud mask (not defined)", __FUNCTION__); - ++priv->cmd_count; spin_unlock_irqrestore(&priv->lock, flags); } - break; - default: - err("%s - unsupported serial control command issued", __FUNCTION__); } + spin_lock_irqsave(&priv->lock, flags); + ++priv->cmd_count; + spin_unlock_irqrestore(&priv->lock, flags); + return retval; } /* cypress_serial_control */ -/* given a baud mask, it will return speed on success */ +/* given a baud mask, it will return integer baud on success */ static int mask_to_rate (unsigned mask) { int rate; @@ -438,11 +443,12 @@ static int generic_startup (struct usb_serial *serial) usb_reset_configuration (serial->dev); + interval = 1; priv->cmd_ctrl = 0; priv->line_control = 0; priv->termios_initialized = 0; - priv->calledfromopen = 0; priv->rx_flags = 0; + priv->cbr_mask = B300; usb_set_serial_port_data(serial->port[0], priv); return (0); @@ -513,7 +519,6 @@ static int cypress_open (struct usb_serial_port *port, struct file *filp) dbg("%s - port %d", __FUNCTION__, port->number); /* clear halts before open */ - usb_clear_halt(serial->dev, 0x00); usb_clear_halt(serial->dev, 0x81); usb_clear_halt(serial->dev, 0x02); @@ -531,7 +536,6 @@ static int cypress_open (struct usb_serial_port *port, struct file *filp) /* raise both lines and set termios */ spin_lock_irqsave(&priv->lock, flags); priv->line_control = CONTROL_DTR | CONTROL_RTS; - priv->calledfromopen = 1; priv->cmd_ctrl = 1; spin_unlock_irqrestore(&priv->lock, flags); result = cypress_write(port, NULL, 0); @@ -553,7 +557,7 @@ static int cypress_open (struct usb_serial_port *port, struct file *filp) usb_fill_int_urb(port->interrupt_in_urb, serial->dev, usb_rcvintpipe(serial->dev, port->interrupt_in_endpointAddress), port->interrupt_in_urb->transfer_buffer, port->interrupt_in_urb->transfer_buffer_length, - cypress_read_int_callback, port, port->interrupt_in_urb->interval); + cypress_read_int_callback, port, interval); result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); if (result){ @@ -680,12 +684,12 @@ static void cypress_send(struct usb_serial_port *port) spin_lock_irqsave(&priv->lock, flags); switch (port->interrupt_out_size) { case 32: - // this is for the CY7C64013... + /* this is for the CY7C64013... */ offset = 2; port->interrupt_out_buffer[0] = priv->line_control; break; case 8: - // this is for the CY7C63743... + /* this is for the CY7C63743... */ offset = 1; port->interrupt_out_buffer[0] = priv->line_control; break; @@ -738,6 +742,7 @@ send: port->interrupt_out_urb->transfer_buffer_length = actual_size; port->interrupt_out_urb->dev = port->serial->dev; + port->interrupt_out_urb->interval = interval; result = usb_submit_urb (port->interrupt_out_urb, GFP_ATOMIC); if (result) { dev_err(&port->dev, "%s - failed submitting write urb, error %d\n", __FUNCTION__, @@ -910,7 +915,7 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o unsigned cflag, iflag, baud_mask; unsigned long flags; __u8 oldlines; - int linechange; + int linechange = 0; dbg("%s - port %d", __FUNCTION__, port->number); @@ -996,15 +1001,7 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o case B115200: dbg("%s - setting baud 115200bps", __FUNCTION__); break; default: dbg("%s - unknown masked baud rate", __FUNCTION__); } - priv->line_control |= CONTROL_DTR; - - /* toggle CRTSCTS? - don't do this if being called from cypress_open */ - if (!priv->calledfromopen) { - if (cflag & CRTSCTS) - priv->line_control |= CONTROL_RTS; - else - priv->line_control &= ~CONTROL_RTS; - } + priv->line_control = (CONTROL_DTR | CONTROL_RTS); } spin_unlock_irqrestore(&priv->lock, flags); @@ -1014,8 +1011,6 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o cypress_serial_control(port, baud_mask, data_bits, stop_bits, parity_enable, parity_type, 0, CYPRESS_SET_CONFIG); - msleep(50); /* give some time between change and read (50ms) */ - /* we perform a CYPRESS_GET_CONFIG so that the current settings are filled into the private structure * this should confirm that all is working if it returns what we just set */ cypress_serial_control(port, 0, 0, 0, 0, 0, 0, CYPRESS_GET_CONFIG); @@ -1031,7 +1026,6 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o dbg("Using custom termios settings for a baud rate of 4800bps."); /* define custom termios settings for NMEA protocol */ - tty->termios->c_iflag /* input modes - */ &= ~(IGNBRK /* disable ignore break */ | BRKINT /* disable break causes interrupt */ @@ -1052,23 +1046,16 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o | ISIG /* disable interrupt, quit, and suspend special characters */ | IEXTEN); /* disable non-POSIX special characters */ - } else if (priv->chiptype == CT_CYPHIDCOM) { - - // Software app handling it for device... + } /* CT_CYPHIDCOM: Application should handle this for device */ - } linechange = (priv->line_control != oldlines); spin_unlock_irqrestore(&priv->lock, flags); /* if necessary, set lines */ - if (!priv->calledfromopen && linechange) { + if (linechange) { priv->cmd_ctrl = 1; cypress_write(port, NULL, 0); } - - if (priv->calledfromopen) - priv->calledfromopen = 0; - } /* cypress_set_termios */ @@ -1164,7 +1151,7 @@ static void cypress_read_int_callback(struct urb *urb, struct pt_regs *regs) spin_lock_irqsave(&priv->lock, flags); switch(urb->actual_length) { case 32: - // This is for the CY7C64013... + /* This is for the CY7C64013... */ priv->current_status = data[0] & 0xF8; bytes = data[1]+2; i=2; @@ -1172,7 +1159,7 @@ static void cypress_read_int_callback(struct urb *urb, struct pt_regs *regs) havedata = 1; break; case 8: - // This is for the CY7C63743... + /* This is for the CY7C63743... */ priv->current_status = data[0] & 0xF8; bytes = (data[0] & 0x07)+1; i=1; @@ -1245,7 +1232,7 @@ continue_read: port->interrupt_in_urb->transfer_buffer, port->interrupt_in_urb->transfer_buffer_length, cypress_read_int_callback, port, - port->interrupt_in_urb->interval); + interval); result = usb_submit_urb(port->interrupt_in_urb, GFP_ATOMIC); if (result) dev_err(&urb->dev->dev, "%s - failed resubmitting read urb, error %d\n", __FUNCTION__, result); @@ -1274,6 +1261,8 @@ static void cypress_write_int_callback(struct urb *urb, struct pt_regs *regs) dbg("%s - urb shutting down with status: %d", __FUNCTION__, urb->status); priv->write_urb_in_use = 0; return; + case -EPIPE: /* no break needed */ + usb_clear_halt(port->serial->dev, 0x02); default: /* error in the urb, so we have to resubmit it */ dbg("%s - Overflow in write", __FUNCTION__); @@ -1535,3 +1524,5 @@ module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug enabled or not"); module_param(stats, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(stats, "Enable statistics or not"); +module_param(interval, int, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(interval, "Overrides interrupt interval"); diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 4c788c7..52394f0 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -76,7 +76,7 @@ * Defererence pointers after any paranoid checks, not before. * * (21/Jun/2003) Erik Nygren - * Added support for Home Electronics Tira-1 IR tranceiver using FT232BM chip. + * Added support for Home Electronics Tira-1 IR transceiver using FT232BM chip. * See <http://www.home-electro.com/tira1.htm>. Only operates properly * at 100000 and RTS-CTS, so set custom divisor mode on startup. * Also force the Tira-1 and USB-UIRT to only use their custom baud rates. @@ -91,7 +91,7 @@ * Minor whitespace and comment changes. * * (12/Jun/2003) David Norwood - * Added support for USB-UIRT IR tranceiver using 8U232AM chip. + * Added support for USB-UIRT IR transceiver using 8U232AM chip. * See <http://home.earthlink.net/~jrhees/USBUIRT/index.htm>. Only * operates properly at 312500, so set custom divisor mode on startup. * @@ -272,6 +272,7 @@ static int debug; static struct usb_device_id id_table_sio [] = { { USB_DEVICE(FTDI_VID, FTDI_SIO_PID) }, + { USB_DEVICE(MOBILITY_VID, MOBILITY_USB_SERIAL_PID) }, { } /* Terminating entry */ }; @@ -296,7 +297,6 @@ static struct usb_device_id id_table_8U232AM [] = { { USB_DEVICE_VER(FTDI_VID, FTDI_IRTRANS_PID, 0, 0x3ff) }, { USB_DEVICE_VER(FTDI_VID, FTDI_8U232AM_PID, 0, 0x3ff) }, { USB_DEVICE_VER(FTDI_VID, FTDI_8U232AM_ALT_PID, 0, 0x3ff) }, - { USB_DEVICE_VER(FTDI_VID, FTDI_8U232AM_ALT_ALT_PID, 0, 0x3ff) }, { USB_DEVICE_VER(FTDI_VID, FTDI_RELAIS_PID, 0, 0x3ff) }, { USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_IOBOARD_PID) }, { USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_MINI_IOBOARD_PID) }, @@ -369,11 +369,14 @@ static struct usb_device_id id_table_8U232AM [] = { { USB_DEVICE_VER(INTREPID_VID, INTREPID_NEOVI_PID, 0, 0x3ff) }, { USB_DEVICE_VER(FALCOM_VID, FALCOM_TWIST_PID, 0, 0x3ff) }, { USB_DEVICE_VER(FTDI_VID, FTDI_SUUNTO_SPORTS_PID, 0, 0x3ff) }, - { USB_DEVICE_VER(FTDI_RM_VID, FTDI_RMCANVIEW_PID, 0, 0x3ff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_RM_CANVIEW_PID, 0, 0x3ff) }, { USB_DEVICE_VER(BANDB_VID, BANDB_USOTL4_PID, 0, 0x3ff) }, { USB_DEVICE_VER(BANDB_VID, BANDB_USTL4_PID, 0, 0x3ff) }, { USB_DEVICE_VER(BANDB_VID, BANDB_USO9ML2_PID, 0, 0x3ff) }, { USB_DEVICE_VER(FTDI_VID, EVER_ECO_PRO_CDS, 0, 0x3ff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_4N_GALAXY_DE_0_PID, 0, 0x3ff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_4N_GALAXY_DE_1_PID, 0, 0x3ff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_4N_GALAXY_DE_2_PID, 0, 0x3ff) }, { } /* Terminating entry */ }; @@ -382,7 +385,6 @@ static struct usb_device_id id_table_FT232BM [] = { { USB_DEVICE_VER(FTDI_VID, FTDI_IRTRANS_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(FTDI_VID, FTDI_8U232AM_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(FTDI_VID, FTDI_8U232AM_ALT_PID, 0x400, 0xffff) }, - { USB_DEVICE_VER(FTDI_VID, FTDI_8U232AM_ALT_ALT_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(FTDI_VID, FTDI_RELAIS_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(FTDI_NF_RIC_VID, FTDI_NF_RIC_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(FTDI_VID, FTDI_XF_632_PID, 0x400, 0xffff) }, @@ -485,11 +487,15 @@ static struct usb_device_id id_table_FT232BM [] = { { USB_DEVICE_VER(INTREPID_VID, INTREPID_NEOVI_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(FALCOM_VID, FALCOM_TWIST_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(FTDI_VID, FTDI_SUUNTO_SPORTS_PID, 0x400, 0xffff) }, - { USB_DEVICE_VER(FTDI_RM_VID, FTDI_RMCANVIEW_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_RM_CANVIEW_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(BANDB_VID, BANDB_USOTL4_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(BANDB_VID, BANDB_USTL4_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(BANDB_VID, BANDB_USO9ML2_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(FTDI_VID, EVER_ECO_PRO_CDS, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_4N_GALAXY_DE_0_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_4N_GALAXY_DE_1_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_4N_GALAXY_DE_2_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_ACTIVE_ROBOTS_PID, 0x400, 0xffff) }, { } /* Terminating entry */ }; @@ -517,7 +523,6 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_SIO_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U232AM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_PID) }, - { USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_ALT_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U2232C_PID) }, { USB_DEVICE(FTDI_VID, FTDI_RELAIS_PID) }, { USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_IOBOARD_PID) }, @@ -596,6 +601,22 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, PROTEGO_R2X0) }, { USB_DEVICE(FTDI_VID, PROTEGO_SPECIAL_3) }, { USB_DEVICE(FTDI_VID, PROTEGO_SPECIAL_4) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E808_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E809_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E80A_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E80B_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E80C_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E80D_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E80E_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E80F_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E888_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E889_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E88A_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E88B_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E88C_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E88D_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E88E_PID, 0x400, 0xffff) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_GUDEADS_E88F_PID, 0x400, 0xffff) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UO100_PID) }, { USB_DEVICE_VER(FTDI_VID, LINX_SDMUSBQSS_PID, 0x400, 0xffff) }, { USB_DEVICE_VER(FTDI_VID, LINX_MASTERDEVEL2_PID, 0x400, 0xffff) }, @@ -609,11 +630,16 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(INTREPID_VID, INTREPID_NEOVI_PID) }, { USB_DEVICE(FALCOM_VID, FALCOM_TWIST_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SUUNTO_SPORTS_PID) }, - { USB_DEVICE(FTDI_RM_VID, FTDI_RMCANVIEW_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_RM_CANVIEW_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USOTL4_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USTL4_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USO9ML2_PID) }, { USB_DEVICE(FTDI_VID, EVER_ECO_PRO_CDS) }, + { USB_DEVICE(FTDI_VID, FTDI_4N_GALAXY_DE_0_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_4N_GALAXY_DE_1_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_4N_GALAXY_DE_2_PID) }, + { USB_DEVICE(MOBILITY_VID, MOBILITY_USB_SERIAL_PID) }, + { USB_DEVICE_VER(FTDI_VID, FTDI_ACTIVE_ROBOTS_PID, 0x400, 0xffff) }, { } /* Terminating entry */ }; @@ -1457,10 +1483,10 @@ static int ftdi_FT2232C_startup (struct usb_serial *serial) inter = serial->interface->altsetting->desc.bInterfaceNumber; if (inter) { - priv->interface = INTERFACE_B; + priv->interface = PIT_SIOB; } else { - priv->interface = INTERFACE_A; + priv->interface = PIT_SIOA; } priv->baud_base = 48000000 / 2; /* Would be / 16, but FT2232C supports multiple of 0.125 divisor fractions! */ diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index be5d60b..a52bb13 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -26,7 +26,6 @@ #define FTDI_SIO_PID 0x8372 /* Product Id SIO application of 8U100AX */ #define FTDI_8U232AM_PID 0x6001 /* Similar device to SIO above */ #define FTDI_8U232AM_ALT_PID 0x6006 /* FTDI's alternate PID for above */ -#define FTDI_8U232AM_ALT_ALT_PID 0xf3c0 /* FTDI's second alternate PID for above */ #define FTDI_8U2232C_PID 0x6010 /* Dual channel device */ #define FTDI_RELAIS_PID 0xFA10 /* Relais device from Rudolf Gugler */ #define FTDI_NF_RIC_VID 0x0DCD /* Vendor Id */ @@ -137,7 +136,7 @@ /* * Home Electronics (www.home-electro.com) USB gadgets */ -#define FTDI_HE_TIRA1_PID 0xFA78 /* Tira-1 IR tranceiver */ +#define FTDI_HE_TIRA1_PID 0xFA78 /* Tira-1 IR transceiver */ /* USB-UIRT - An infrared receiver and transmitter using the 8U232AM chip */ /* http://home.earthlink.net/~jrhees/USBUIRT/index.htm */ @@ -157,7 +156,8 @@ */ #define OCT_VID 0x0B39 /* OCT vendor ID */ /* Note: OCT US101 is also rebadged as Dick Smith Electronics (NZ) XH6381 */ -/* Also rebadged as SIIG Inc. model US2308 */ +/* Also rebadged as Dick Smith Electronics (Aus) XH6451 */ +/* Also rebadged as SIIG Inc. model US2308 hardware version 1 */ #define OCT_US101_PID 0x0421 /* OCT US101 USB to RS-232 */ /* an infrared receiver for user access control with IR tags */ @@ -236,10 +236,10 @@ /* * RM Michaelides CANview USB (http://www.rmcan.com) - * CAN filedbus interface adapter, addad by port GmbH www.port.de) + * CAN fieldbus interface adapter, added by port GmbH www.port.de) + * Ian Abbott changed the macro names for consistency. */ -#define FTDI_RM_VID 0x0403 /* Vendor Id */ -#define FTDI_RMCANVIEW_PID 0xfd60 /* Product Id */ +#define FTDI_RM_CANVIEW_PID 0xfd60 /* Product Id */ /* * EVER Eco Pro UPS (http://www.ever.com.pl/) @@ -247,6 +247,26 @@ #define EVER_ECO_PRO_CDS 0xe520 /* RS-232 converter */ +/* + * 4N-GALAXY.DE PIDs for CAN-USB, USB-RS232, USB-RS422, USB-RS485, + * USB-TTY activ, USB-TTY passiv. Some PIDs are used by several devices + * and I'm not entirely sure which are used by which. + */ +#define FTDI_4N_GALAXY_DE_0_PID 0x8372 +#define FTDI_4N_GALAXY_DE_1_PID 0xF3C0 +#define FTDI_4N_GALAXY_DE_2_PID 0xF3C1 + +/* + * Mobility Electronics products. + */ +#define MOBILITY_VID 0x1342 +#define MOBILITY_USB_SERIAL_PID 0x0202 /* EasiDock USB 200 serial */ + +/* + * Active Robots product ids. + */ +#define FTDI_ACTIVE_ROBOTS_PID 0xE548 /* USB comms board */ + /* Commands */ #define FTDI_SIO_RESET 0 /* Reset the port */ #define FTDI_SIO_MODEM_CTRL 1 /* Set the modem control register */ @@ -259,10 +279,6 @@ #define FTDI_SIO_SET_LATENCY_TIMER 9 /* Set the latency timer */ #define FTDI_SIO_GET_LATENCY_TIMER 10 /* Get the latency timer */ -/* Port interface code for FT2232C */ -#define INTERFACE_A 1 -#define INTERFACE_B 2 - /* * BmRequestType: 1100 0000b diff --git a/drivers/usb/serial/io_usbvend.h b/drivers/usb/serial/io_usbvend.h index 8c1fa5e..f1804fd 100644 --- a/drivers/usb/serial/io_usbvend.h +++ b/drivers/usb/serial/io_usbvend.h @@ -289,7 +289,7 @@ // // -// Edgeport Compatiblity Descriptor +// Edgeport Compatibility Descriptor // // This descriptor is only returned by Edgeport-compatible devices // supporting the EPiC spec. True ION devices do not return this diff --git a/drivers/usb/serial/keyspan_usa90msg.h b/drivers/usb/serial/keyspan_usa90msg.h index dd935b6..86708ec 100644 --- a/drivers/usb/serial/keyspan_usa90msg.h +++ b/drivers/usb/serial/keyspan_usa90msg.h @@ -19,7 +19,7 @@ This file is available under a BSD-style copyright - 2. The name of InnoSys Incorprated may not be used to endorse or promote + 2. The name of InnoSys Incorporated may not be used to endorse or promote products derived from this software without specific prior written permission. diff --git a/drivers/usb/storage/debug.c b/drivers/usb/storage/debug.c index d764837..5a93217 100644 --- a/drivers/usb/storage/debug.c +++ b/drivers/usb/storage/debug.c @@ -47,6 +47,7 @@ #include <linux/cdrom.h> #include <scsi/scsi.h> #include <scsi/scsi_cmnd.h> +#include <scsi/scsi_dbg.h> #include "debug.h" #include "scsi.h" diff --git a/drivers/usb/storage/shuttle_usbat.c b/drivers/usb/storage/shuttle_usbat.c index 7eff03d..f3b6028 100644 --- a/drivers/usb/storage/shuttle_usbat.c +++ b/drivers/usb/storage/shuttle_usbat.c @@ -786,7 +786,7 @@ static int usbat_flash_check_media(struct us_data *us, if (rc != USB_STOR_XFER_GOOD) return USB_STOR_TRANSPORT_ERROR; - // Check for media existance + // Check for media existence rc = usbat_flash_check_media_present(uio); if (rc == USBAT_FLASH_MEDIA_NONE) { info->sense_key = 0x02; diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index bbda63c2..d2891f4 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -1,5 +1,5 @@ /* Driver for USB Mass Storage compliant devices - * Ununsual Devices File + * Unusual Devices File * * $Id: unusual_devs.h,v 1.32 2002/02/25 02:41:24 mdharm Exp $ * @@ -48,6 +48,14 @@ * USB development list <linux-usb-devel@lists.sourceforge.net>. */ +/* patch submitted by Vivian Bregier <Vivian.Bregier@imag.fr> + */ +UNUSUAL_DEV( 0x03eb, 0x2002, 0x0100, 0x0100, + "ATMEL", + "SND1 Storage", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_IGNORE_RESIDUE), + UNUSUAL_DEV( 0x03ee, 0x6901, 0x0000, 0x0100, "Mitsumi", "USB FDD", @@ -994,6 +1002,13 @@ UNUSUAL_DEV( 0x1019, 0x0c55, 0x0000, 0x9999, US_SC_DEVICE, US_PR_DEVICE, usb_stor_ucr61s2b_init, 0 ), +/* Reported by Vilius Bilinkevicius <vilisas AT xxx DOT lt) */ +UNUSUAL_DEV( 0x132b, 0x000b, 0x0001, 0x0001, + "Minolta", + "Dimage Z10", + US_SC_DEVICE, US_PR_DEVICE, NULL, + 0 ), + /* Reported by Kotrla Vitezslav <kotrla@ceb.cz> */ UNUSUAL_DEV( 0x1370, 0x6828, 0x0110, 0x0110, "SWISSBIT", |
