diff options
Diffstat (limited to 'drivers/usb/net/Kconfig')
| -rw-r--r-- | drivers/usb/net/Kconfig | 123 |
1 files changed, 64 insertions, 59 deletions
diff --git a/drivers/usb/net/Kconfig b/drivers/usb/net/Kconfig index 135d508..6399b43 100644 --- a/drivers/usb/net/Kconfig +++ b/drivers/usb/net/Kconfig @@ -128,32 +128,6 @@ config USB_USBNET comment "USB Host-to-Host Cables" depends on USB_USBNET -config USB_ALI_M5632 - boolean "ALi M5632 based 'USB 2.0 Data Link' cables" - depends on USB_USBNET - default y - help - Choose this option if you're using a host-to-host cable - based on this design, which supports USB 2.0 high speed. - -config USB_AN2720 - boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)" - depends on USB_USBNET - default y - help - Choose this option if you're using a host-to-host cable - based on this design. Note that AnchorChips is now a - Cypress brand. - -config USB_BELKIN - boolean "eTEK based host-to-host cables (Advance, Belkin, ...)" - depends on USB_USBNET - default y - help - Choose this option if you're using a host-to-host cable - based on this design: two NetChip 2890 chips and an Atmel - microcontroller, with LEDs that indicate traffic. - config USB_GENESYS boolean "GeneSys GL620USB-A based cables" default y @@ -182,42 +156,9 @@ config USB_PL2301 Choose this option if you're using a host-to-host cable with one of these chips. -config USB_KC2190 - boolean "KT Technology KC2190 based cables (InstaNet)" - default y - depends on USB_USBNET && EXPERIMENTAL - help - Choose this option if you're using a host-to-host cable - with one of these chips. - comment "Intelligent USB Devices/Gadgets" depends on USB_USBNET -config USB_ARMLINUX - boolean "Embedded ARM Linux links (iPaq, ...)" - depends on USB_USBNET - default y - help - Choose this option to support the "usb-eth" networking driver - used by most of the ARM Linux community with device controllers - such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities - in some PXA versions of the "blob" boot loader. - - Linux-based "Gumstix" PXA-25x based systems use this protocol - to talk with other Linux systems. - - Although the ROMs shipped with Sharp Zaurus products use a - different link level framing protocol, you can have them use - this simpler protocol by installing a different kernel. - -config USB_EPSON2888 - boolean "Epson 2888 based firmware (DEVELOPMENT)" - depends on USB_USBNET - default y - help - Choose this option to support the usb networking links used - by some sample firmware from Epson. - config USB_ZAURUS boolean "Sharp Zaurus (stock ROMs) and compatible" depends on USB_USBNET @@ -292,6 +233,70 @@ config USB_AX8817X This driver creates an interface named "ethX", where X depends on what other networking devices you have in use. + +config USB_NET_CDC_SUBSET + tristate "Simple USB Network Links (CDC Ethernet subset)" + depends on USB_USBNET + help + This driver module supports USB network devices that can work + without any device-specific information. Select it if you have + one of these drivers. + + Note that while many USB host-to-host cables can work in this mode, + that may mean not being able to talk to Win32 systems or more + commonly not being able to handle certain events (like replugging + the host on the other end) very well. Also, these devices will + not generally have permanently assigned Ethernet addresses. + +config USB_ALI_M5632 + boolean "ALi M5632 based 'USB 2.0 Data Link' cables" + depends on USB_NET_CDC_SUBSET + help + Choose this option if you're using a host-to-host cable + based on this design, which supports USB 2.0 high speed. + +config USB_AN2720 + boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)" + depends on USB_NET_CDC_SUBSET + help + Choose this option if you're using a host-to-host cable + based on this design. Note that AnchorChips is now a + Cypress brand. + +config USB_BELKIN + boolean "eTEK based host-to-host cables (Advance, Belkin, ...)" + depends on USB_NET_CDC_SUBSET + default y + help + Choose this option if you're using a host-to-host cable + based on this design: two NetChip 2890 chips and an Atmel + microcontroller, with LEDs that indicate traffic. + +config USB_ARMLINUX + boolean "Embedded ARM Linux links (iPaq, ...)" + depends on USB_NET_CDC_SUBSET + default y + help + Choose this option to support the "usb-eth" networking driver + used by most of the ARM Linux community with device controllers + such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities + in some PXA versions of the "blob" boot loader. + + Linux-based "Gumstix" PXA-25x based systems use this protocol + to talk with other Linux systems. + + Although the ROMs shipped with Sharp Zaurus products use a + different link level framing protocol, you can have them use + this simpler protocol by installing a different kernel. + +config USB_EPSON2888 + boolean "Epson 2888 based firmware (DEVELOPMENT)" + depends on USB_NET_CDC_SUBSET + help + Choose this option to support the usb networking links used + by some sample firmware from Epson. + + config USB_ZD1201 tristate "USB ZD1201 based Wireless device support" depends on NET_RADIO |
