summaryrefslogtreecommitdiffstats
path: root/drivers/tty/serial/serial_lh7a40x.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/serial_lh7a40x.c')
-rw-r--r--drivers/tty/serial/serial_lh7a40x.c682
1 files changed, 682 insertions, 0 deletions
diff --git a/drivers/tty/serial/serial_lh7a40x.c b/drivers/tty/serial/serial_lh7a40x.c
new file mode 100644
index 0000000..ea74470
--- /dev/null
+++ b/drivers/tty/serial/serial_lh7a40x.c
@@ -0,0 +1,682 @@
+/* drivers/serial/serial_lh7a40x.c
+ *
+ * Copyright (C) 2004 Coastal Environmental Systems
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ */
+
+/* Driver for Sharp LH7A40X embedded serial ports
+ *
+ * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ * Based on drivers/serial/amba.c, by Deep Blue Solutions Ltd.
+ *
+ * ---
+ *
+ * This driver supports the embedded UARTs of the Sharp LH7A40X series
+ * CPUs. While similar to the 16550 and other UART chips, there is
+ * nothing close to register compatibility. Moreover, some of the
+ * modem control lines are not available, either in the chip or they
+ * are lacking in the board-level implementation.
+ *
+ * - Use of SIRDIS
+ * For simplicity, we disable the IR functions of any UART whenever
+ * we enable it.
+ *
+ */
+
+
+#if defined(CONFIG_SERIAL_LH7A40X_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/io.h>
+
+#include <asm/irq.h>
+#include <mach/hardware.h>
+
+#define DEV_MAJOR 204
+#define DEV_MINOR 16
+#define DEV_NR 3
+
+#define ISR_LOOP_LIMIT 256
+
+#define UR(p,o) _UR ((p)->membase, o)
+#define _UR(b,o) (*((volatile unsigned int*)(((unsigned char*) b) + (o))))
+#define BIT_CLR(p,o,m) UR(p,o) = UR(p,o) & (~(unsigned int)m)
+#define BIT_SET(p,o,m) UR(p,o) = UR(p,o) | ( (unsigned int)m)
+
+#define UART_REG_SIZE 32
+
+#define UART_R_DATA (0x00)
+#define UART_R_FCON (0x04)
+#define UART_R_BRCON (0x08)
+#define UART_R_CON (0x0c)
+#define UART_R_STATUS (0x10)
+#define UART_R_RAWISR (0x14)
+#define UART_R_INTEN (0x18)
+#define UART_R_ISR (0x1c)
+
+#define UARTEN (0x01) /* UART enable */
+#define SIRDIS (0x02) /* Serial IR disable (UART1 only) */
+
+#define RxEmpty (0x10)
+#define TxEmpty (0x80)
+#define TxFull (0x20)
+#define nRxRdy RxEmpty
+#define nTxRdy TxFull
+#define TxBusy (0x08)
+
+#define RxBreak (0x0800)
+#define RxOverrunError (0x0400)
+#define RxParityError (0x0200)
+#define RxFramingError (0x0100)
+#define RxError (RxBreak | RxOverrunError | RxParityError | RxFramingError)
+
+#define DCD (0x04)
+#define DSR (0x02)
+#define CTS (0x01)
+
+#define RxInt (0x01)
+#define TxInt (0x02)
+#define ModemInt (0x04)
+#define RxTimeoutInt (0x08)
+
+#define MSEOI (0x10)
+
+#define WLEN_8 (0x60)
+#define WLEN_7 (0x40)
+#define WLEN_6 (0x20)
+#define WLEN_5 (0x00)
+#define WLEN (0x60) /* Mask for all word-length bits */
+#define STP2 (0x08)
+#define PEN (0x02) /* Parity Enable */
+#define EPS (0x04) /* Even Parity Set */
+#define FEN (0x10) /* FIFO Enable */
+#define BRK (0x01) /* Send Break */
+
+
+struct uart_port_lh7a40x {
+ struct uart_port port;
+ unsigned int statusPrev; /* Most recently read modem status */
+};
+
+static void lh7a40xuart_stop_tx (struct uart_port* port)
+{
+ BIT_CLR (port, UART_R_INTEN, TxInt);
+}
+
+static void lh7a40xuart_start_tx (struct uart_port* port)
+{
+ BIT_SET (port, UART_R_INTEN, TxInt);
+
+ /* *** FIXME: do I need to check for startup of the
+ transmitter? The old driver did, but AMBA
+ doesn't . */
+}
+
+static void lh7a40xuart_stop_rx (struct uart_port* port)
+{
+ BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt);
+}
+
+static void lh7a40xuart_enable_ms (struct uart_port* port)
+{
+ BIT_SET (port, UART_R_INTEN, ModemInt);
+}
+
+static void lh7a40xuart_rx_chars (struct uart_port* port)
+{
+ struct tty_struct* tty = port->state->port.tty;
+ int cbRxMax = 256; /* (Gross) limit on receive */
+ unsigned int data; /* Received data and status */
+ unsigned int flag;
+
+ while (!(UR (port, UART_R_STATUS) & nRxRdy) && --cbRxMax) {
+ data = UR (port, UART_R_DATA);
+ flag = TTY_NORMAL;
+ ++port->icount.rx;
+
+ if (unlikely(data & RxError)) {
+ if (data & RxBreak) {
+ data &= ~(RxFramingError | RxParityError);
+ ++port->icount.brk;
+ if (uart_handle_break (port))
+ continue;
+ }
+ else if (data & RxParityError)
+ ++port->icount.parity;
+ else if (data & RxFramingError)
+ ++port->icount.frame;
+ if (data & RxOverrunError)
+ ++port->icount.overrun;
+
+ /* Mask by termios, leave Rx'd byte */
+ data &= port->read_status_mask | 0xff;
+
+ if (data & RxBreak)
+ flag = TTY_BREAK;
+ else if (data & RxParityError)
+ flag = TTY_PARITY;
+ else if (data & RxFramingError)
+ flag = TTY_FRAME;
+ }
+
+ if (uart_handle_sysrq_char (port, (unsigned char) data))
+ continue;
+
+ uart_insert_char(port, data, RxOverrunError, data, flag);
+ }
+ tty_flip_buffer_push (tty);
+ return;
+}
+
+static void lh7a40xuart_tx_chars (struct uart_port* port)
+{
+ struct circ_buf* xmit = &port->state->xmit;
+ int cbTxMax = port->fifosize;
+
+ if (port->x_char) {
+ UR (port, UART_R_DATA) = port->x_char;
+ ++port->icount.tx;
+ port->x_char = 0;
+ return;
+ }
+ if (uart_circ_empty (xmit) || uart_tx_stopped (port)) {
+ lh7a40xuart_stop_tx (port);
+ return;
+ }
+
+ /* Unlike the AMBA UART, the lh7a40x UART does not guarantee
+ that at least half of the FIFO is empty. Instead, we check
+ status for every character. Using the AMBA method causes
+ the transmitter to drop characters. */
+
+ do {
+ UR (port, UART_R_DATA) = xmit->buf[xmit->tail];
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ ++port->icount.tx;
+ if (uart_circ_empty(xmit))
+ break;
+ } while (!(UR (port, UART_R_STATUS) & nTxRdy)
+ && cbTxMax--);
+
+ if (uart_circ_chars_pending (xmit) < WAKEUP_CHARS)
+ uart_write_wakeup (port);
+
+ if (uart_circ_empty (xmit))
+ lh7a40xuart_stop_tx (port);
+}
+
+static void lh7a40xuart_modem_status (struct uart_port* port)
+{
+ unsigned int status = UR (port, UART_R_STATUS);
+ unsigned int delta
+ = status ^ ((struct uart_port_lh7a40x*) port)->statusPrev;
+
+ BIT_SET (port, UART_R_RAWISR, MSEOI); /* Clear modem status intr */
+
+ if (!delta) /* Only happens if we missed 2 transitions */
+ return;
+
+ ((struct uart_port_lh7a40x*) port)->statusPrev = status;
+
+ if (delta & DCD)
+ uart_handle_dcd_change (port, status & DCD);
+
+ if (delta & DSR)
+ ++port->icount.dsr;
+
+ if (delta & CTS)
+ uart_handle_cts_change (port, status & CTS);
+
+ wake_up_interruptible (&port->state->port.delta_msr_wait);
+}
+
+static irqreturn_t lh7a40xuart_int (int irq, void* dev_id)
+{
+ struct uart_port* port = dev_id;
+ unsigned int cLoopLimit = ISR_LOOP_LIMIT;
+ unsigned int isr = UR (port, UART_R_ISR);
+
+
+ do {
+ if (isr & (RxInt | RxTimeoutInt))
+ lh7a40xuart_rx_chars(port);
+ if (isr & ModemInt)
+ lh7a40xuart_modem_status (port);
+ if (isr & TxInt)
+ lh7a40xuart_tx_chars (port);
+
+ if (--cLoopLimit == 0)
+ break;
+
+ isr = UR (port, UART_R_ISR);
+ } while (isr & (RxInt | TxInt | RxTimeoutInt));
+
+ return IRQ_HANDLED;
+}
+
+static unsigned int lh7a40xuart_tx_empty (struct uart_port* port)
+{
+ return (UR (port, UART_R_STATUS) & TxEmpty) ? TIOCSER_TEMT : 0;
+}
+
+static unsigned int lh7a40xuart_get_mctrl (struct uart_port* port)
+{
+ unsigned int result = 0;
+ unsigned int status = UR (port, UART_R_STATUS);
+
+ if (status & DCD)
+ result |= TIOCM_CAR;
+ if (status & DSR)
+ result |= TIOCM_DSR;
+ if (status & CTS)
+ result |= TIOCM_CTS;
+
+ return result;
+}
+
+static void lh7a40xuart_set_mctrl (struct uart_port* port, unsigned int mctrl)
+{
+ /* None of the ports supports DTR. UART1 supports RTS through GPIO. */
+ /* Note, kernel appears to be setting DTR and RTS on console. */
+
+ /* *** FIXME: this deserves more work. There's some work in
+ tracing all of the IO pins. */
+#if 0
+ if( port->mapbase == UART1_PHYS) {
+ gpioRegs_t *gpio = (gpioRegs_t *)IO_ADDRESS(GPIO_PHYS);
+
+ if (mctrl & TIOCM_RTS)
+ gpio->pbdr &= ~GPIOB_UART1_RTS;
+ else
+ gpio->pbdr |= GPIOB_UART1_RTS;
+ }
+#endif
+}
+
+static void lh7a40xuart_break_ctl (struct uart_port* port, int break_state)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+ if (break_state == -1)
+ BIT_SET (port, UART_R_FCON, BRK); /* Assert break */
+ else
+ BIT_CLR (port, UART_R_FCON, BRK); /* Deassert break */
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static int lh7a40xuart_startup (struct uart_port* port)
+{
+ int retval;
+
+ retval = request_irq (port->irq, lh7a40xuart_int, 0,
+ "serial_lh7a40x", port);
+ if (retval)
+ return retval;
+
+ /* Initial modem control-line settings */
+ ((struct uart_port_lh7a40x*) port)->statusPrev
+ = UR (port, UART_R_STATUS);
+
+ /* There is presently no configuration option to enable IR.
+ Thus, we always disable it. */
+
+ BIT_SET (port, UART_R_CON, UARTEN | SIRDIS);
+ BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt);
+
+ return 0;
+}
+
+static void lh7a40xuart_shutdown (struct uart_port* port)
+{
+ free_irq (port->irq, port);
+ BIT_CLR (port, UART_R_FCON, BRK | FEN);
+ BIT_CLR (port, UART_R_CON, UARTEN);
+}
+
+static void lh7a40xuart_set_termios (struct uart_port* port,
+ struct ktermios* termios,
+ struct ktermios* old)
+{
+ unsigned int con;
+ unsigned int inten;
+ unsigned int fcon;
+ unsigned long flags;
+ unsigned int baud;
+ unsigned int quot;
+
+ baud = uart_get_baud_rate (port, termios, old, 8, port->uartclk/16);
+ quot = uart_get_divisor (port, baud); /* -1 performed elsewhere */
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ fcon = WLEN_5;
+ break;
+ case CS6:
+ fcon = WLEN_6;
+ break;
+ case CS7:
+ fcon = WLEN_7;
+ break;
+ case CS8:
+ default:
+ fcon = WLEN_8;
+ break;
+ }
+ if (termios->c_cflag & CSTOPB)
+ fcon |= STP2;
+ if (termios->c_cflag & PARENB) {
+ fcon |= PEN;
+ if (!(termios->c_cflag & PARODD))
+ fcon |= EPS;
+ }
+ if (port->fifosize > 1)
+ fcon |= FEN;
+
+ spin_lock_irqsave (&port->lock, flags);
+
+ uart_update_timeout (port, termios->c_cflag, baud);
+
+ port->read_status_mask = RxOverrunError;
+ if (termios->c_iflag & INPCK)
+ port->read_status_mask |= RxFramingError | RxParityError;
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ port->read_status_mask |= RxBreak;
+
+ /* Figure mask for status we ignore */
+ port->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= RxFramingError | RxParityError;
+ if (termios->c_iflag & IGNBRK) {
+ port->ignore_status_mask |= RxBreak;
+ /* Ignore overrun when ignorning parity */
+ /* *** FIXME: is this in the right place? */
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= RxOverrunError;
+ }
+
+ /* Ignore all receive errors when receive disabled */
+ if ((termios->c_cflag & CREAD) == 0)
+ port->ignore_status_mask |= RxError;
+
+ con = UR (port, UART_R_CON);
+ inten = (UR (port, UART_R_INTEN) & ~ModemInt);
+
+ if (UART_ENABLE_MS (port, termios->c_cflag))
+ inten |= ModemInt;
+
+ BIT_CLR (port, UART_R_CON, UARTEN); /* Disable UART */
+ UR (port, UART_R_INTEN) = 0; /* Disable interrupts */
+ UR (port, UART_R_BRCON) = quot - 1; /* Set baud rate divisor */
+ UR (port, UART_R_FCON) = fcon; /* Set FIFO and frame ctrl */
+ UR (port, UART_R_INTEN) = inten; /* Enable interrupts */
+ UR (port, UART_R_CON) = con; /* Restore UART mode */
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char* lh7a40xuart_type (struct uart_port* port)
+{
+ return port->type == PORT_LH7A40X ? "LH7A40X" : NULL;
+}
+
+static void lh7a40xuart_release_port (struct uart_port* port)
+{
+ release_mem_region (port->mapbase, UART_REG_SIZE);
+}
+
+static int lh7a40xuart_request_port (struct uart_port* port)
+{
+ return request_mem_region (port->mapbase, UART_REG_SIZE,
+ "serial_lh7a40x") != NULL
+ ? 0 : -EBUSY;
+}
+
+static void lh7a40xuart_config_port (struct uart_port* port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE) {
+ port->type = PORT_LH7A40X;
+ lh7a40xuart_request_port (port);
+ }
+}
+
+static int lh7a40xuart_verify_port (struct uart_port* port,
+ struct serial_struct* ser)
+{
+ int ret = 0;
+
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_LH7A40X)
+ ret = -EINVAL;
+ if (ser->irq < 0 || ser->irq >= nr_irqs)
+ ret = -EINVAL;
+ if (ser->baud_base < 9600) /* *** FIXME: is this true? */
+ ret = -EINVAL;
+ return ret;
+}
+
+static struct uart_ops lh7a40x_uart_ops = {
+ .tx_empty = lh7a40xuart_tx_empty,
+ .set_mctrl = lh7a40xuart_set_mctrl,
+ .get_mctrl = lh7a40xuart_get_mctrl,
+ .stop_tx = lh7a40xuart_stop_tx,
+ .start_tx = lh7a40xuart_start_tx,
+ .stop_rx = lh7a40xuart_stop_rx,
+ .enable_ms = lh7a40xuart_enable_ms,
+ .break_ctl = lh7a40xuart_break_ctl,
+ .startup = lh7a40xuart_startup,
+ .shutdown = lh7a40xuart_shutdown,
+ .set_termios = lh7a40xuart_set_termios,
+ .type = lh7a40xuart_type,
+ .release_port = lh7a40xuart_release_port,
+ .request_port = lh7a40xuart_request_port,
+ .config_port = lh7a40xuart_config_port,
+ .verify_port = lh7a40xuart_verify_port,
+};
+
+static struct uart_port_lh7a40x lh7a40x_ports[DEV_NR] = {
+ {
+ .port = {
+ .membase = (void*) io_p2v (UART1_PHYS),
+ .mapbase = UART1_PHYS,
+ .iotype = UPIO_MEM,
+ .irq = IRQ_UART1INTR,
+ .uartclk = 14745600/2,
+ .fifosize = 16,
+ .ops = &lh7a40x_uart_ops,
+ .flags = UPF_BOOT_AUTOCONF,
+ .line = 0,
+ },
+ },
+ {
+ .port = {
+ .membase = (void*) io_p2v (UART2_PHYS),
+ .mapbase = UART2_PHYS,
+ .iotype = UPIO_MEM,
+ .irq = IRQ_UART2INTR,
+ .uartclk = 14745600/2,
+ .fifosize = 16,
+ .ops = &lh7a40x_uart_ops,
+ .flags = UPF_BOOT_AUTOCONF,
+ .line = 1,
+ },
+ },
+ {
+ .port = {
+ .membase = (void*) io_p2v (UART3_PHYS),
+ .mapbase = UART3_PHYS,
+ .iotype = UPIO_MEM,
+ .irq = IRQ_UART3INTR,
+ .uartclk = 14745600/2,
+ .fifosize = 16,
+ .ops = &lh7a40x_uart_ops,
+ .flags = UPF_BOOT_AUTOCONF,
+ .line = 2,
+ },
+ },
+};
+
+#ifndef CONFIG_SERIAL_LH7A40X_CONSOLE
+# define LH7A40X_CONSOLE NULL
+#else
+# define LH7A40X_CONSOLE &lh7a40x_console
+
+static void lh7a40xuart_console_putchar(struct uart_port *port, int ch)
+{
+ while (UR(port, UART_R_STATUS) & nTxRdy)
+ ;
+ UR(port, UART_R_DATA) = ch;
+}
+
+static void lh7a40xuart_console_write (struct console* co,
+ const char* s,
+ unsigned int count)
+{
+ struct uart_port* port = &lh7a40x_ports[co->index].port;
+ unsigned int con = UR (port, UART_R_CON);
+ unsigned int inten = UR (port, UART_R_INTEN);
+
+
+ UR (port, UART_R_INTEN) = 0; /* Disable all interrupts */
+ BIT_SET (port, UART_R_CON, UARTEN | SIRDIS); /* Enable UART */
+
+ uart_console_write(port, s, count, lh7a40xuart_console_putchar);
+
+ /* Wait until all characters are sent */
+ while (UR (port, UART_R_STATUS) & TxBusy)
+ ;
+
+ /* Restore control and interrupt mask */
+ UR (port, UART_R_CON) = con;
+ UR (port, UART_R_INTEN) = inten;
+}
+
+static void __init lh7a40xuart_console_get_options (struct uart_port* port,
+ int* baud,
+ int* parity,
+ int* bits)
+{
+ if (UR (port, UART_R_CON) & UARTEN) {
+ unsigned int fcon = UR (port, UART_R_FCON);
+ unsigned int quot = UR (port, UART_R_BRCON) + 1;
+
+ switch (fcon & (PEN | EPS)) {
+ default: *parity = 'n'; break;
+ case PEN: *parity = 'o'; break;
+ case PEN | EPS: *parity = 'e'; break;
+ }
+
+ switch (fcon & WLEN) {
+ default:
+ case WLEN_8: *bits = 8; break;
+ case WLEN_7: *bits = 7; break;
+ case WLEN_6: *bits = 6; break;
+ case WLEN_5: *bits = 5; break;
+ }
+
+ *baud = port->uartclk/(16*quot);
+ }
+}
+
+static int __init lh7a40xuart_console_setup (struct console* co, char* options)
+{
+ struct uart_port* port;
+ int baud = 38400;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index >= DEV_NR) /* Bounds check on device number */
+ co->index = 0;
+ port = &lh7a40x_ports[co->index].port;
+
+ if (options)
+ uart_parse_options (options, &baud, &parity, &bits, &flow);
+ else
+ lh7a40xuart_console_get_options (port, &baud, &parity, &bits);
+
+ return uart_set_options (port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver lh7a40x_reg;
+static struct console lh7a40x_console = {
+ .name = "ttyAM",
+ .write = lh7a40xuart_console_write,
+ .device = uart_console_device,
+ .setup = lh7a40xuart_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &lh7a40x_reg,
+};
+
+static int __init lh7a40xuart_console_init(void)
+{
+ register_console (&lh7a40x_console);
+ return 0;
+}
+
+console_initcall (lh7a40xuart_console_init);
+
+#endif
+
+static struct uart_driver lh7a40x_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "ttyAM",
+ .dev_name = "ttyAM",
+ .major = DEV_MAJOR,
+ .minor = DEV_MINOR,
+ .nr = DEV_NR,
+ .cons = LH7A40X_CONSOLE,
+};
+
+static int __init lh7a40xuart_init(void)
+{
+ int ret;
+
+ printk (KERN_INFO "serial: LH7A40X serial driver\n");
+
+ ret = uart_register_driver (&lh7a40x_reg);
+
+ if (ret == 0) {
+ int i;
+
+ for (i = 0; i < DEV_NR; i++) {
+ /* UART3, when used, requires GPIO pin reallocation */
+ if (lh7a40x_ports[i].port.mapbase == UART3_PHYS)
+ GPIO_PINMUX |= 1<<3;
+ uart_add_one_port (&lh7a40x_reg,
+ &lh7a40x_ports[i].port);
+ }
+ }
+ return ret;
+}
+
+static void __exit lh7a40xuart_exit(void)
+{
+ int i;
+
+ for (i = 0; i < DEV_NR; i++)
+ uart_remove_one_port (&lh7a40x_reg, &lh7a40x_ports[i].port);
+
+ uart_unregister_driver (&lh7a40x_reg);
+}
+
+module_init (lh7a40xuart_init);
+module_exit (lh7a40xuart_exit);
+
+MODULE_AUTHOR ("Marc Singer");
+MODULE_DESCRIPTION ("Sharp LH7A40X serial port driver");
+MODULE_LICENSE ("GPL");
OpenPOWER on IntegriCloud