summaryrefslogtreecommitdiffstats
path: root/drivers/tty/serial/max3107.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/max3107.c')
-rw-r--r--drivers/tty/serial/max3107.c1213
1 files changed, 1213 insertions, 0 deletions
diff --git a/drivers/tty/serial/max3107.c b/drivers/tty/serial/max3107.c
new file mode 100644
index 0000000..910870e
--- /dev/null
+++ b/drivers/tty/serial/max3107.c
@@ -0,0 +1,1213 @@
+/*
+ * max3107.c - spi uart protocol driver for Maxim 3107
+ * Based on max3100.c
+ * by Christian Pellegrin <chripell@evolware.org>
+ * and max3110.c
+ * by Feng Tang <feng.tang@intel.com>
+ *
+ * Copyright (C) Aavamobile 2009
+ *
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/gpio.h>
+#include <linux/spi/spi.h>
+#include <linux/freezer.h>
+#include "max3107.h"
+
+static const struct baud_table brg26_ext[] = {
+ { 300, MAX3107_BRG26_B300 },
+ { 600, MAX3107_BRG26_B600 },
+ { 1200, MAX3107_BRG26_B1200 },
+ { 2400, MAX3107_BRG26_B2400 },
+ { 4800, MAX3107_BRG26_B4800 },
+ { 9600, MAX3107_BRG26_B9600 },
+ { 19200, MAX3107_BRG26_B19200 },
+ { 57600, MAX3107_BRG26_B57600 },
+ { 115200, MAX3107_BRG26_B115200 },
+ { 230400, MAX3107_BRG26_B230400 },
+ { 460800, MAX3107_BRG26_B460800 },
+ { 921600, MAX3107_BRG26_B921600 },
+ { 0, 0 }
+};
+
+static const struct baud_table brg13_int[] = {
+ { 300, MAX3107_BRG13_IB300 },
+ { 600, MAX3107_BRG13_IB600 },
+ { 1200, MAX3107_BRG13_IB1200 },
+ { 2400, MAX3107_BRG13_IB2400 },
+ { 4800, MAX3107_BRG13_IB4800 },
+ { 9600, MAX3107_BRG13_IB9600 },
+ { 19200, MAX3107_BRG13_IB19200 },
+ { 57600, MAX3107_BRG13_IB57600 },
+ { 115200, MAX3107_BRG13_IB115200 },
+ { 230400, MAX3107_BRG13_IB230400 },
+ { 460800, MAX3107_BRG13_IB460800 },
+ { 921600, MAX3107_BRG13_IB921600 },
+ { 0, 0 }
+};
+
+static u32 get_new_brg(int baud, struct max3107_port *s)
+{
+ int i;
+ const struct baud_table *baud_tbl = s->baud_tbl;
+
+ for (i = 0; i < 13; i++) {
+ if (baud == baud_tbl[i].baud)
+ return baud_tbl[i].new_brg;
+ }
+
+ return 0;
+}
+
+/* Perform SPI transfer for write/read of device register(s) */
+int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len)
+{
+ struct spi_message spi_msg;
+ struct spi_transfer spi_xfer;
+
+ /* Initialize SPI ,message */
+ spi_message_init(&spi_msg);
+
+ /* Initialize SPI transfer */
+ memset(&spi_xfer, 0, sizeof spi_xfer);
+ spi_xfer.len = len;
+ spi_xfer.tx_buf = tx;
+ spi_xfer.rx_buf = rx;
+ spi_xfer.speed_hz = MAX3107_SPI_SPEED;
+
+ /* Add SPI transfer to SPI message */
+ spi_message_add_tail(&spi_xfer, &spi_msg);
+
+#ifdef DBG_TRACE_SPI_DATA
+ {
+ int i;
+ pr_info("tx len %d:\n", spi_xfer.len);
+ for (i = 0 ; i < spi_xfer.len && i < 32 ; i++)
+ pr_info(" %x", ((u8 *)spi_xfer.tx_buf)[i]);
+ pr_info("\n");
+ }
+#endif
+
+ /* Perform synchronous SPI transfer */
+ if (spi_sync(s->spi, &spi_msg)) {
+ dev_err(&s->spi->dev, "spi_sync failure\n");
+ return -EIO;
+ }
+
+#ifdef DBG_TRACE_SPI_DATA
+ if (spi_xfer.rx_buf) {
+ int i;
+ pr_info("rx len %d:\n", spi_xfer.len);
+ for (i = 0 ; i < spi_xfer.len && i < 32 ; i++)
+ pr_info(" %x", ((u8 *)spi_xfer.rx_buf)[i]);
+ pr_info("\n");
+ }
+#endif
+ return 0;
+}
+EXPORT_SYMBOL_GPL(max3107_rw);
+
+/* Puts received data to circular buffer */
+static void put_data_to_circ_buf(struct max3107_port *s, unsigned char *data,
+ int len)
+{
+ struct uart_port *port = &s->port;
+ struct tty_struct *tty;
+
+ if (!port->state)
+ return;
+
+ tty = port->state->port.tty;
+ if (!tty)
+ return;
+
+ /* Insert received data */
+ tty_insert_flip_string(tty, data, len);
+ /* Update RX counter */
+ port->icount.rx += len;
+}
+
+/* Handle data receiving */
+static void max3107_handlerx(struct max3107_port *s, u16 rxlvl)
+{
+ int i;
+ int j;
+ int len; /* SPI transfer buffer length */
+ u16 *buf;
+ u8 *valid_str;
+
+ if (!s->rx_enabled)
+ /* RX is disabled */
+ return;
+
+ if (rxlvl == 0) {
+ /* RX fifo is empty */
+ return;
+ } else if (rxlvl >= MAX3107_RX_FIFO_SIZE) {
+ dev_warn(&s->spi->dev, "Possible RX FIFO overrun %d\n", rxlvl);
+ /* Ensure sanity of RX level */
+ rxlvl = MAX3107_RX_FIFO_SIZE;
+ }
+ if ((s->rxbuf == 0) || (s->rxstr == 0)) {
+ dev_warn(&s->spi->dev, "Rx buffer/str isn't ready\n");
+ return;
+ }
+ buf = s->rxbuf;
+ valid_str = s->rxstr;
+ while (rxlvl) {
+ pr_debug("rxlvl %d\n", rxlvl);
+ /* Clear buffer */
+ memset(buf, 0, sizeof(u16) * (MAX3107_RX_FIFO_SIZE + 2));
+ len = 0;
+ if (s->irqen_reg & MAX3107_IRQ_RXFIFO_BIT) {
+ /* First disable RX FIFO interrupt */
+ pr_debug("Disabling RX INT\n");
+ buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
+ s->irqen_reg &= ~MAX3107_IRQ_RXFIFO_BIT;
+ buf[0] |= s->irqen_reg;
+ len++;
+ }
+ /* Just increase the length by amount of words in FIFO since
+ * buffer was zeroed and SPI transfer of 0x0000 means reading
+ * from RX FIFO
+ */
+ len += rxlvl;
+ /* Append RX level query */
+ buf[len] = MAX3107_RXFIFOLVL_REG;
+ len++;
+
+ /* Perform the SPI transfer */
+ if (max3107_rw(s, (u8 *)buf, (u8 *)buf, len * 2)) {
+ dev_err(&s->spi->dev, "SPI transfer for RX h failed\n");
+ return;
+ }
+
+ /* Skip RX FIFO interrupt disabling word if it was added */
+ j = ((len - 1) - rxlvl);
+ /* Read received words */
+ for (i = 0; i < rxlvl; i++, j++)
+ valid_str[i] = (u8)buf[j];
+ put_data_to_circ_buf(s, valid_str, rxlvl);
+ /* Get new RX level */
+ rxlvl = (buf[len - 1] & MAX3107_SPI_RX_DATA_MASK);
+ }
+
+ if (s->rx_enabled) {
+ /* RX still enabled, re-enable RX FIFO interrupt */
+ pr_debug("Enabling RX INT\n");
+ buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
+ s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT;
+ buf[0] |= s->irqen_reg;
+ if (max3107_rw(s, (u8 *)buf, NULL, 2))
+ dev_err(&s->spi->dev, "RX FIFO INT enabling failed\n");
+ }
+
+ /* Push the received data to receivers */
+ if (s->port.state->port.tty)
+ tty_flip_buffer_push(s->port.state->port.tty);
+}
+
+
+/* Handle data sending */
+static void max3107_handletx(struct max3107_port *s)
+{
+ struct circ_buf *xmit = &s->port.state->xmit;
+ int i;
+ unsigned long flags;
+ int len; /* SPI transfer buffer length */
+ u16 *buf;
+
+ if (!s->tx_fifo_empty)
+ /* Don't send more data before previous data is sent */
+ return;
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&s->port))
+ /* No data to send or TX is stopped */
+ return;
+
+ if (!s->txbuf) {
+ dev_warn(&s->spi->dev, "Txbuf isn't ready\n");
+ return;
+ }
+ buf = s->txbuf;
+ /* Get length of data pending in circular buffer */
+ len = uart_circ_chars_pending(xmit);
+ if (len) {
+ /* Limit to size of TX FIFO */
+ if (len > MAX3107_TX_FIFO_SIZE)
+ len = MAX3107_TX_FIFO_SIZE;
+
+ pr_debug("txlen %d\n", len);
+
+ /* Update TX counter */
+ s->port.icount.tx += len;
+
+ /* TX FIFO will no longer be empty */
+ s->tx_fifo_empty = 0;
+
+ i = 0;
+ if (s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT) {
+ /* First disable TX empty interrupt */
+ pr_debug("Disabling TE INT\n");
+ buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
+ s->irqen_reg &= ~MAX3107_IRQ_TXEMPTY_BIT;
+ buf[i] |= s->irqen_reg;
+ i++;
+ len++;
+ }
+ /* Add data to send */
+ spin_lock_irqsave(&s->port.lock, flags);
+ for ( ; i < len ; i++) {
+ buf[i] = (MAX3107_WRITE_BIT | MAX3107_THR_REG);
+ buf[i] |= ((u16)xmit->buf[xmit->tail] &
+ MAX3107_SPI_TX_DATA_MASK);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ }
+ spin_unlock_irqrestore(&s->port.lock, flags);
+ if (!(s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT)) {
+ /* Enable TX empty interrupt */
+ pr_debug("Enabling TE INT\n");
+ buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
+ s->irqen_reg |= MAX3107_IRQ_TXEMPTY_BIT;
+ buf[i] |= s->irqen_reg;
+ i++;
+ len++;
+ }
+ if (!s->tx_enabled) {
+ /* Enable TX */
+ pr_debug("Enable TX\n");
+ buf[i] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
+ spin_lock_irqsave(&s->data_lock, flags);
+ s->mode1_reg &= ~MAX3107_MODE1_TXDIS_BIT;
+ buf[i] |= s->mode1_reg;
+ spin_unlock_irqrestore(&s->data_lock, flags);
+ s->tx_enabled = 1;
+ i++;
+ len++;
+ }
+
+ /* Perform the SPI transfer */
+ if (max3107_rw(s, (u8 *)buf, NULL, len*2)) {
+ dev_err(&s->spi->dev,
+ "SPI transfer TX handling failed\n");
+ return;
+ }
+ }
+
+ /* Indicate wake up if circular buffer is getting low on data */
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&s->port);
+
+}
+
+/* Handle interrupts
+ * Also reads and returns current RX FIFO level
+ */
+static u16 handle_interrupt(struct max3107_port *s)
+{
+ u16 buf[4]; /* Buffer for SPI transfers */
+ u8 irq_status;
+ u16 rx_level;
+ unsigned long flags;
+
+ /* Read IRQ status register */
+ buf[0] = MAX3107_IRQSTS_REG;
+ /* Read status IRQ status register */
+ buf[1] = MAX3107_STS_IRQSTS_REG;
+ /* Read LSR IRQ status register */
+ buf[2] = MAX3107_LSR_IRQSTS_REG;
+ /* Query RX level */
+ buf[3] = MAX3107_RXFIFOLVL_REG;
+
+ if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 8)) {
+ dev_err(&s->spi->dev,
+ "SPI transfer for INTR handling failed\n");
+ return 0;
+ }
+
+ irq_status = (u8)buf[0];
+ pr_debug("IRQSTS %x\n", irq_status);
+ rx_level = (buf[3] & MAX3107_SPI_RX_DATA_MASK);
+
+ if (irq_status & MAX3107_IRQ_LSR_BIT) {
+ /* LSR interrupt */
+ if (buf[2] & MAX3107_LSR_RXTO_BIT)
+ /* RX timeout interrupt,
+ * handled by normal RX handling
+ */
+ pr_debug("RX TO INT\n");
+ }
+
+ if (irq_status & MAX3107_IRQ_TXEMPTY_BIT) {
+ /* Tx empty interrupt,
+ * disable TX and set tx_fifo_empty flag
+ */
+ pr_debug("TE INT, disabling TX\n");
+ buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
+ spin_lock_irqsave(&s->data_lock, flags);
+ s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT;
+ buf[0] |= s->mode1_reg;
+ spin_unlock_irqrestore(&s->data_lock, flags);
+ if (max3107_rw(s, (u8 *)buf, NULL, 2))
+ dev_err(&s->spi->dev, "SPI transfer TX dis failed\n");
+ s->tx_enabled = 0;
+ s->tx_fifo_empty = 1;
+ }
+
+ if (irq_status & MAX3107_IRQ_RXFIFO_BIT)
+ /* RX FIFO interrupt,
+ * handled by normal RX handling
+ */
+ pr_debug("RFIFO INT\n");
+
+ /* Return RX level */
+ return rx_level;
+}
+
+/* Trigger work thread*/
+static void max3107_dowork(struct max3107_port *s)
+{
+ if (!work_pending(&s->work) && !freezing(current) && !s->suspended)
+ queue_work(s->workqueue, &s->work);
+ else
+ dev_warn(&s->spi->dev, "interrup isn't serviced normally!\n");
+}
+
+/* Work thread */
+static void max3107_work(struct work_struct *w)
+{
+ struct max3107_port *s = container_of(w, struct max3107_port, work);
+ u16 rxlvl = 0;
+ int len; /* SPI transfer buffer length */
+ u16 buf[5]; /* Buffer for SPI transfers */
+ unsigned long flags;
+
+ /* Start by reading current RX FIFO level */
+ buf[0] = MAX3107_RXFIFOLVL_REG;
+ if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) {
+ dev_err(&s->spi->dev, "SPI transfer RX lev failed\n");
+ rxlvl = 0;
+ } else {
+ rxlvl = (buf[0] & MAX3107_SPI_RX_DATA_MASK);
+ }
+
+ do {
+ pr_debug("rxlvl %d\n", rxlvl);
+
+ /* Handle RX */
+ max3107_handlerx(s, rxlvl);
+ rxlvl = 0;
+
+ if (s->handle_irq) {
+ /* Handle pending interrupts
+ * We also get new RX FIFO level since new data may
+ * have been received while pushing received data to
+ * receivers
+ */
+ s->handle_irq = 0;
+ rxlvl = handle_interrupt(s);
+ }
+
+ /* Handle TX */
+ max3107_handletx(s);
+
+ /* Handle configuration changes */
+ len = 0;
+ spin_lock_irqsave(&s->data_lock, flags);
+ if (s->mode1_commit) {
+ pr_debug("mode1_commit\n");
+ buf[len] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
+ buf[len++] |= s->mode1_reg;
+ s->mode1_commit = 0;
+ }
+ if (s->lcr_commit) {
+ pr_debug("lcr_commit\n");
+ buf[len] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG);
+ buf[len++] |= s->lcr_reg;
+ s->lcr_commit = 0;
+ }
+ if (s->brg_commit) {
+ pr_debug("brg_commit\n");
+ buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG);
+ buf[len++] |= ((s->brg_cfg >> 16) &
+ MAX3107_SPI_TX_DATA_MASK);
+ buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG);
+ buf[len++] |= ((s->brg_cfg >> 8) &
+ MAX3107_SPI_TX_DATA_MASK);
+ buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG);
+ buf[len++] |= ((s->brg_cfg) & 0xff);
+ s->brg_commit = 0;
+ }
+ spin_unlock_irqrestore(&s->data_lock, flags);
+
+ if (len > 0) {
+ if (max3107_rw(s, (u8 *)buf, NULL, len * 2))
+ dev_err(&s->spi->dev,
+ "SPI transfer config failed\n");
+ }
+
+ /* Reloop if interrupt handling indicated data in RX FIFO */
+ } while (rxlvl);
+
+}
+
+/* Set sleep mode */
+static void max3107_set_sleep(struct max3107_port *s, int mode)
+{
+ u16 buf[1]; /* Buffer for SPI transfer */
+ unsigned long flags;
+ pr_debug("enter, mode %d\n", mode);
+
+ buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
+ spin_lock_irqsave(&s->data_lock, flags);
+ switch (mode) {
+ case MAX3107_DISABLE_FORCED_SLEEP:
+ s->mode1_reg &= ~MAX3107_MODE1_FORCESLEEP_BIT;
+ break;
+ case MAX3107_ENABLE_FORCED_SLEEP:
+ s->mode1_reg |= MAX3107_MODE1_FORCESLEEP_BIT;
+ break;
+ case MAX3107_DISABLE_AUTOSLEEP:
+ s->mode1_reg &= ~MAX3107_MODE1_AUTOSLEEP_BIT;
+ break;
+ case MAX3107_ENABLE_AUTOSLEEP:
+ s->mode1_reg |= MAX3107_MODE1_AUTOSLEEP_BIT;
+ break;
+ default:
+ spin_unlock_irqrestore(&s->data_lock, flags);
+ dev_warn(&s->spi->dev, "invalid sleep mode\n");
+ return;
+ }
+ buf[0] |= s->mode1_reg;
+ spin_unlock_irqrestore(&s->data_lock, flags);
+
+ if (max3107_rw(s, (u8 *)buf, NULL, 2))
+ dev_err(&s->spi->dev, "SPI transfer sleep mode failed\n");
+
+ if (mode == MAX3107_DISABLE_AUTOSLEEP ||
+ mode == MAX3107_DISABLE_FORCED_SLEEP)
+ msleep(MAX3107_WAKEUP_DELAY);
+}
+
+/* Perform full register initialization */
+static void max3107_register_init(struct max3107_port *s)
+{
+ u16 buf[11]; /* Buffer for SPI transfers */
+
+ /* 1. Configure baud rate, 9600 as default */
+ s->baud = 9600;
+ /* the below is default*/
+ if (s->ext_clk) {
+ s->brg_cfg = MAX3107_BRG26_B9600;
+ s->baud_tbl = (struct baud_table *)brg26_ext;
+ } else {
+ s->brg_cfg = MAX3107_BRG13_IB9600;
+ s->baud_tbl = (struct baud_table *)brg13_int;
+ }
+
+ if (s->pdata->init)
+ s->pdata->init(s);
+
+ buf[0] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG)
+ | ((s->brg_cfg >> 16) & MAX3107_SPI_TX_DATA_MASK);
+ buf[1] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG)
+ | ((s->brg_cfg >> 8) & MAX3107_SPI_TX_DATA_MASK);
+ buf[2] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG)
+ | ((s->brg_cfg) & 0xff);
+
+ /* 2. Configure LCR register, 8N1 mode by default */
+ s->lcr_reg = MAX3107_LCR_WORD_LEN_8;
+ buf[3] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG)
+ | s->lcr_reg;
+
+ /* 3. Configure MODE 1 register */
+ s->mode1_reg = 0;
+ /* Enable IRQ pin */
+ s->mode1_reg |= MAX3107_MODE1_IRQSEL_BIT;
+ /* Disable TX */
+ s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT;
+ s->tx_enabled = 0;
+ /* RX is enabled */
+ s->rx_enabled = 1;
+ buf[4] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG)
+ | s->mode1_reg;
+
+ /* 4. Configure MODE 2 register */
+ buf[5] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG);
+ if (s->loopback) {
+ /* Enable loopback */
+ buf[5] |= MAX3107_MODE2_LOOPBACK_BIT;
+ }
+ /* Reset FIFOs */
+ buf[5] |= MAX3107_MODE2_FIFORST_BIT;
+ s->tx_fifo_empty = 1;
+
+ /* 5. Configure FIFO trigger level register */
+ buf[6] = (MAX3107_WRITE_BIT | MAX3107_FIFOTRIGLVL_REG);
+ /* RX FIFO trigger for 16 words, TX FIFO trigger not used */
+ buf[6] |= (MAX3107_FIFOTRIGLVL_RX(16) | MAX3107_FIFOTRIGLVL_TX(0));
+
+ /* 6. Configure flow control levels */
+ buf[7] = (MAX3107_WRITE_BIT | MAX3107_FLOWLVL_REG);
+ /* Flow control halt level 96, resume level 48 */
+ buf[7] |= (MAX3107_FLOWLVL_RES(48) | MAX3107_FLOWLVL_HALT(96));
+
+ /* 7. Configure flow control */
+ buf[8] = (MAX3107_WRITE_BIT | MAX3107_FLOWCTRL_REG);
+ /* Enable auto CTS and auto RTS flow control */
+ buf[8] |= (MAX3107_FLOWCTRL_AUTOCTS_BIT | MAX3107_FLOWCTRL_AUTORTS_BIT);
+
+ /* 8. Configure RX timeout register */
+ buf[9] = (MAX3107_WRITE_BIT | MAX3107_RXTO_REG);
+ /* Timeout after 48 character intervals */
+ buf[9] |= 0x0030;
+
+ /* 9. Configure LSR interrupt enable register */
+ buf[10] = (MAX3107_WRITE_BIT | MAX3107_LSR_IRQEN_REG);
+ /* Enable RX timeout interrupt */
+ buf[10] |= MAX3107_LSR_RXTO_BIT;
+
+ /* Perform SPI transfer */
+ if (max3107_rw(s, (u8 *)buf, NULL, 22))
+ dev_err(&s->spi->dev, "SPI transfer for init failed\n");
+
+ /* 10. Clear IRQ status register by reading it */
+ buf[0] = MAX3107_IRQSTS_REG;
+
+ /* 11. Configure interrupt enable register */
+ /* Enable LSR interrupt */
+ s->irqen_reg = MAX3107_IRQ_LSR_BIT;
+ /* Enable RX FIFO interrupt */
+ s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT;
+ buf[1] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG)
+ | s->irqen_reg;
+
+ /* 12. Clear FIFO reset that was set in step 6 */
+ buf[2] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG);
+ if (s->loopback) {
+ /* Keep loopback enabled */
+ buf[2] |= MAX3107_MODE2_LOOPBACK_BIT;
+ }
+
+ /* Perform SPI transfer */
+ if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 6))
+ dev_err(&s->spi->dev, "SPI transfer for init failed\n");
+
+}
+
+/* IRQ handler */
+static irqreturn_t max3107_irq(int irqno, void *dev_id)
+{
+ struct max3107_port *s = dev_id;
+
+ if (irqno != s->spi->irq) {
+ /* Unexpected IRQ */
+ return IRQ_NONE;
+ }
+
+ /* Indicate irq */
+ s->handle_irq = 1;
+
+ /* Trigger work thread */
+ max3107_dowork(s);
+
+ return IRQ_HANDLED;
+}
+
+/* HW suspension function
+ *
+ * Currently autosleep is used to decrease current consumption, alternative
+ * approach would be to set the chip to reset mode if UART is not being
+ * used but that would mess the GPIOs
+ *
+ */
+void max3107_hw_susp(struct max3107_port *s, int suspend)
+{
+ pr_debug("enter, suspend %d\n", suspend);
+
+ if (suspend) {
+ /* Suspend requested,
+ * enable autosleep to decrease current consumption
+ */
+ s->suspended = 1;
+ max3107_set_sleep(s, MAX3107_ENABLE_AUTOSLEEP);
+ } else {
+ /* Resume requested,
+ * disable autosleep
+ */
+ s->suspended = 0;
+ max3107_set_sleep(s, MAX3107_DISABLE_AUTOSLEEP);
+ }
+}
+EXPORT_SYMBOL_GPL(max3107_hw_susp);
+
+/* Modem status IRQ enabling */
+static void max3107_enable_ms(struct uart_port *port)
+{
+ /* Modem status not supported */
+}
+
+/* Data send function */
+static void max3107_start_tx(struct uart_port *port)
+{
+ struct max3107_port *s = container_of(port, struct max3107_port, port);
+
+ /* Trigger work thread for sending data */
+ max3107_dowork(s);
+}
+
+/* Function for checking that there is no pending transfers */
+static unsigned int max3107_tx_empty(struct uart_port *port)
+{
+ struct max3107_port *s = container_of(port, struct max3107_port, port);
+
+ pr_debug("returning %d\n",
+ (s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit)));
+ return s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit);
+}
+
+/* Function for stopping RX */
+static void max3107_stop_rx(struct uart_port *port)
+{
+ struct max3107_port *s = container_of(port, struct max3107_port, port);
+ unsigned long flags;
+
+ /* Set RX disabled in MODE 1 register */
+ spin_lock_irqsave(&s->data_lock, flags);
+ s->mode1_reg |= MAX3107_MODE1_RXDIS_BIT;
+ s->mode1_commit = 1;
+ spin_unlock_irqrestore(&s->data_lock, flags);
+ /* Set RX disabled */
+ s->rx_enabled = 0;
+ /* Trigger work thread for doing the actual configuration change */
+ max3107_dowork(s);
+}
+
+/* Function for returning control pin states */
+static unsigned int max3107_get_mctrl(struct uart_port *port)
+{
+ /* DCD and DSR are not wired and CTS/RTS is handled automatically
+ * so just indicate DSR and CAR asserted
+ */
+ return TIOCM_DSR | TIOCM_CAR;
+}
+
+/* Function for setting control pin states */
+static void max3107_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ /* DCD and DSR are not wired and CTS/RTS is hadnled automatically
+ * so do nothing
+ */
+}
+
+/* Function for configuring UART parameters */
+static void max3107_set_termios(struct uart_port *port,
+ struct ktermios *termios,
+ struct ktermios *old)
+{
+ struct max3107_port *s = container_of(port, struct max3107_port, port);
+ struct tty_struct *tty;
+ int baud;
+ u16 new_lcr = 0;
+ u32 new_brg = 0;
+ unsigned long flags;
+
+ if (!port->state)
+ return;
+
+ tty = port->state->port.tty;
+ if (!tty)
+ return;
+
+ /* Get new LCR register values */
+ /* Word size */
+ if ((termios->c_cflag & CSIZE) == CS7)
+ new_lcr |= MAX3107_LCR_WORD_LEN_7;
+ else
+ new_lcr |= MAX3107_LCR_WORD_LEN_8;
+
+ /* Parity */
+ if (termios->c_cflag & PARENB) {
+ new_lcr |= MAX3107_LCR_PARITY_BIT;
+ if (!(termios->c_cflag & PARODD))
+ new_lcr |= MAX3107_LCR_EVENPARITY_BIT;
+ }
+
+ /* Stop bits */
+ if (termios->c_cflag & CSTOPB) {
+ /* 2 stop bits */
+ new_lcr |= MAX3107_LCR_STOPLEN_BIT;
+ }
+
+ /* Mask termios capabilities we don't support */
+ termios->c_cflag &= ~CMSPAR;
+
+ /* Set status ignore mask */
+ s->port.ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ s->port.ignore_status_mask |= MAX3107_ALL_ERRORS;
+
+ /* Set low latency to immediately handle pushed data */
+ s->port.state->port.tty->low_latency = 1;
+
+ /* Get new baud rate generator configuration */
+ baud = tty_get_baud_rate(tty);
+
+ spin_lock_irqsave(&s->data_lock, flags);
+ new_brg = get_new_brg(baud, s);
+ /* if can't find the corrent config, use previous */
+ if (!new_brg) {
+ baud = s->baud;
+ new_brg = s->brg_cfg;
+ }
+ spin_unlock_irqrestore(&s->data_lock, flags);
+ tty_termios_encode_baud_rate(termios, baud, baud);
+ s->baud = baud;
+
+ /* Update timeout according to new baud rate */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ spin_lock_irqsave(&s->data_lock, flags);
+ if (s->lcr_reg != new_lcr) {
+ s->lcr_reg = new_lcr;
+ s->lcr_commit = 1;
+ }
+ if (s->brg_cfg != new_brg) {
+ s->brg_cfg = new_brg;
+ s->brg_commit = 1;
+ }
+ spin_unlock_irqrestore(&s->data_lock, flags);
+
+ /* Trigger work thread for doing the actual configuration change */
+ max3107_dowork(s);
+}
+
+/* Port shutdown function */
+static void max3107_shutdown(struct uart_port *port)
+{
+ struct max3107_port *s = container_of(port, struct max3107_port, port);
+
+ if (s->suspended && s->pdata->hw_suspend)
+ s->pdata->hw_suspend(s, 0);
+
+ /* Free the interrupt */
+ free_irq(s->spi->irq, s);
+
+ if (s->workqueue) {
+ /* Flush and destroy work queue */
+ flush_workqueue(s->workqueue);
+ destroy_workqueue(s->workqueue);
+ s->workqueue = NULL;
+ }
+
+ /* Suspend HW */
+ if (s->pdata->hw_suspend)
+ s->pdata->hw_suspend(s, 1);
+}
+
+/* Port startup function */
+static int max3107_startup(struct uart_port *port)
+{
+ struct max3107_port *s = container_of(port, struct max3107_port, port);
+
+ /* Initialize work queue */
+ s->workqueue = create_freezeable_workqueue("max3107");
+ if (!s->workqueue) {
+ dev_err(&s->spi->dev, "Workqueue creation failed\n");
+ return -EBUSY;
+ }
+ INIT_WORK(&s->work, max3107_work);
+
+ /* Setup IRQ */
+ if (request_irq(s->spi->irq, max3107_irq, IRQF_TRIGGER_FALLING,
+ "max3107", s)) {
+ dev_err(&s->spi->dev, "IRQ reguest failed\n");
+ destroy_workqueue(s->workqueue);
+ s->workqueue = NULL;
+ return -EBUSY;
+ }
+
+ /* Resume HW */
+ if (s->pdata->hw_suspend)
+ s->pdata->hw_suspend(s, 0);
+
+ /* Init registers */
+ max3107_register_init(s);
+
+ return 0;
+}
+
+/* Port type function */
+static const char *max3107_type(struct uart_port *port)
+{
+ struct max3107_port *s = container_of(port, struct max3107_port, port);
+ return s->spi->modalias;
+}
+
+/* Port release function */
+static void max3107_release_port(struct uart_port *port)
+{
+ /* Do nothing */
+}
+
+/* Port request function */
+static int max3107_request_port(struct uart_port *port)
+{
+ /* Do nothing */
+ return 0;
+}
+
+/* Port config function */
+static void max3107_config_port(struct uart_port *port, int flags)
+{
+ struct max3107_port *s = container_of(port, struct max3107_port, port);
+ s->port.type = PORT_MAX3107;
+}
+
+/* Port verify function */
+static int max3107_verify_port(struct uart_port *port,
+ struct serial_struct *ser)
+{
+ if (ser->type == PORT_UNKNOWN || ser->type == PORT_MAX3107)
+ return 0;
+
+ return -EINVAL;
+}
+
+/* Port stop TX function */
+static void max3107_stop_tx(struct uart_port *port)
+{
+ /* Do nothing */
+}
+
+/* Port break control function */
+static void max3107_break_ctl(struct uart_port *port, int break_state)
+{
+ /* We don't support break control, do nothing */
+}
+
+
+/* Port functions */
+static struct uart_ops max3107_ops = {
+ .tx_empty = max3107_tx_empty,
+ .set_mctrl = max3107_set_mctrl,
+ .get_mctrl = max3107_get_mctrl,
+ .stop_tx = max3107_stop_tx,
+ .start_tx = max3107_start_tx,
+ .stop_rx = max3107_stop_rx,
+ .enable_ms = max3107_enable_ms,
+ .break_ctl = max3107_break_ctl,
+ .startup = max3107_startup,
+ .shutdown = max3107_shutdown,
+ .set_termios = max3107_set_termios,
+ .type = max3107_type,
+ .release_port = max3107_release_port,
+ .request_port = max3107_request_port,
+ .config_port = max3107_config_port,
+ .verify_port = max3107_verify_port,
+};
+
+/* UART driver data */
+static struct uart_driver max3107_uart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "ttyMAX",
+ .dev_name = "ttyMAX",
+ .nr = 1,
+};
+
+static int driver_registered = 0;
+
+
+
+/* 'Generic' platform data */
+static struct max3107_plat generic_plat_data = {
+ .loopback = 0,
+ .ext_clk = 1,
+ .hw_suspend = max3107_hw_susp,
+ .polled_mode = 0,
+ .poll_time = 0,
+};
+
+
+/*******************************************************************/
+
+/**
+ * max3107_probe - SPI bus probe entry point
+ * @spi: the spi device
+ *
+ * SPI wants us to probe this device and if appropriate claim it.
+ * Perform any platform specific requirements and then initialise
+ * the device.
+ */
+
+int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata)
+{
+ struct max3107_port *s;
+ u16 buf[2]; /* Buffer for SPI transfers */
+ int retval;
+
+ pr_info("enter max3107 probe\n");
+
+ /* Allocate port structure */
+ s = kzalloc(sizeof(*s), GFP_KERNEL);
+ if (!s) {
+ pr_err("Allocating port structure failed\n");
+ return -ENOMEM;
+ }
+
+ s->pdata = pdata;
+
+ /* SPI Rx buffer
+ * +2 for RX FIFO interrupt
+ * disabling and RX level query
+ */
+ s->rxbuf = kzalloc(sizeof(u16) * (MAX3107_RX_FIFO_SIZE+2), GFP_KERNEL);
+ if (!s->rxbuf) {
+ pr_err("Allocating RX buffer failed\n");
+ retval = -ENOMEM;
+ goto err_free4;
+ }
+ s->rxstr = kzalloc(sizeof(u8) * MAX3107_RX_FIFO_SIZE, GFP_KERNEL);
+ if (!s->rxstr) {
+ pr_err("Allocating RX buffer failed\n");
+ retval = -ENOMEM;
+ goto err_free3;
+ }
+ /* SPI Tx buffer
+ * SPI transfer buffer
+ * +3 for TX FIFO empty
+ * interrupt disabling and
+ * enabling and TX enabling
+ */
+ s->txbuf = kzalloc(sizeof(u16) * MAX3107_TX_FIFO_SIZE + 3, GFP_KERNEL);
+ if (!s->txbuf) {
+ pr_err("Allocating TX buffer failed\n");
+ retval = -ENOMEM;
+ goto err_free2;
+ }
+ /* Initialize shared data lock */
+ spin_lock_init(&s->data_lock);
+
+ /* SPI intializations */
+ dev_set_drvdata(&spi->dev, s);
+ spi->mode = SPI_MODE_0;
+ spi->dev.platform_data = pdata;
+ spi->bits_per_word = 16;
+ s->ext_clk = pdata->ext_clk;
+ s->loopback = pdata->loopback;
+ spi_setup(spi);
+ s->spi = spi;
+
+ /* Check REV ID to ensure we are talking to what we expect */
+ buf[0] = MAX3107_REVID_REG;
+ if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) {
+ dev_err(&s->spi->dev, "SPI transfer for REVID read failed\n");
+ retval = -EIO;
+ goto err_free1;
+ }
+ if ((buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID1 &&
+ (buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID2) {
+ dev_err(&s->spi->dev, "REVID %x does not match\n",
+ (buf[0] & MAX3107_SPI_RX_DATA_MASK));
+ retval = -ENODEV;
+ goto err_free1;
+ }
+
+ /* Disable all interrupts */
+ buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG | 0x0000);
+ buf[0] |= 0x0000;
+
+ /* Configure clock source */
+ buf[1] = (MAX3107_WRITE_BIT | MAX3107_CLKSRC_REG);
+ if (s->ext_clk) {
+ /* External clock */
+ buf[1] |= MAX3107_CLKSRC_EXTCLK_BIT;
+ }
+
+ /* PLL bypass ON */
+ buf[1] |= MAX3107_CLKSRC_PLLBYP_BIT;
+
+ /* Perform SPI transfer */
+ if (max3107_rw(s, (u8 *)buf, NULL, 4)) {
+ dev_err(&s->spi->dev, "SPI transfer for init failed\n");
+ retval = -EIO;
+ goto err_free1;
+ }
+
+ /* Register UART driver */
+ if (!driver_registered) {
+ retval = uart_register_driver(&max3107_uart_driver);
+ if (retval) {
+ dev_err(&s->spi->dev, "Registering UART driver failed\n");
+ goto err_free1;
+ }
+ driver_registered = 1;
+ }
+
+ /* Initialize UART port data */
+ s->port.fifosize = 128;
+ s->port.ops = &max3107_ops;
+ s->port.line = 0;
+ s->port.dev = &spi->dev;
+ s->port.uartclk = 9600;
+ s->port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
+ s->port.irq = s->spi->irq;
+ s->port.type = PORT_MAX3107;
+
+ /* Add UART port */
+ retval = uart_add_one_port(&max3107_uart_driver, &s->port);
+ if (retval < 0) {
+ dev_err(&s->spi->dev, "Adding UART port failed\n");
+ goto err_free1;
+ }
+
+ if (pdata->configure) {
+ retval = pdata->configure(s);
+ if (retval < 0)
+ goto err_free1;
+ }
+
+ /* Go to suspend mode */
+ if (pdata->hw_suspend)
+ pdata->hw_suspend(s, 1);
+
+ return 0;
+
+err_free1:
+ kfree(s->txbuf);
+err_free2:
+ kfree(s->rxstr);
+err_free3:
+ kfree(s->rxbuf);
+err_free4:
+ kfree(s);
+ return retval;
+}
+EXPORT_SYMBOL_GPL(max3107_probe);
+
+/* Driver remove function */
+int max3107_remove(struct spi_device *spi)
+{
+ struct max3107_port *s = dev_get_drvdata(&spi->dev);
+
+ pr_info("enter max3107 remove\n");
+
+ /* Remove port */
+ if (uart_remove_one_port(&max3107_uart_driver, &s->port))
+ dev_warn(&s->spi->dev, "Removing UART port failed\n");
+
+
+ /* Free TxRx buffer */
+ kfree(s->rxbuf);
+ kfree(s->rxstr);
+ kfree(s->txbuf);
+
+ /* Free port structure */
+ kfree(s);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(max3107_remove);
+
+/* Driver suspend function */
+int max3107_suspend(struct spi_device *spi, pm_message_t state)
+{
+#ifdef CONFIG_PM
+ struct max3107_port *s = dev_get_drvdata(&spi->dev);
+
+ pr_debug("enter suspend\n");
+
+ /* Suspend UART port */
+ uart_suspend_port(&max3107_uart_driver, &s->port);
+
+ /* Go to suspend mode */
+ if (s->pdata->hw_suspend)
+ s->pdata->hw_suspend(s, 1);
+#endif /* CONFIG_PM */
+ return 0;
+}
+EXPORT_SYMBOL_GPL(max3107_suspend);
+
+/* Driver resume function */
+int max3107_resume(struct spi_device *spi)
+{
+#ifdef CONFIG_PM
+ struct max3107_port *s = dev_get_drvdata(&spi->dev);
+
+ pr_debug("enter resume\n");
+
+ /* Resume from suspend */
+ if (s->pdata->hw_suspend)
+ s->pdata->hw_suspend(s, 0);
+
+ /* Resume UART port */
+ uart_resume_port(&max3107_uart_driver, &s->port);
+#endif /* CONFIG_PM */
+ return 0;
+}
+EXPORT_SYMBOL_GPL(max3107_resume);
+
+static int max3107_probe_generic(struct spi_device *spi)
+{
+ return max3107_probe(spi, &generic_plat_data);
+}
+
+/* Spi driver data */
+static struct spi_driver max3107_driver = {
+ .driver = {
+ .name = "max3107",
+ .bus = &spi_bus_type,
+ .owner = THIS_MODULE,
+ },
+ .probe = max3107_probe_generic,
+ .remove = __devexit_p(max3107_remove),
+ .suspend = max3107_suspend,
+ .resume = max3107_resume,
+};
+
+/* Driver init function */
+static int __init max3107_init(void)
+{
+ pr_info("enter max3107 init\n");
+ return spi_register_driver(&max3107_driver);
+}
+
+/* Driver exit function */
+static void __exit max3107_exit(void)
+{
+ pr_info("enter max3107 exit\n");
+ /* Unregister UART driver */
+ if (driver_registered)
+ uart_unregister_driver(&max3107_uart_driver);
+ spi_unregister_driver(&max3107_driver);
+}
+
+module_init(max3107_init);
+module_exit(max3107_exit);
+
+MODULE_DESCRIPTION("MAX3107 driver");
+MODULE_AUTHOR("Aavamobile");
+MODULE_ALIAS("max3107-spi");
+MODULE_LICENSE("GPL v2");
OpenPOWER on IntegriCloud