diff options
Diffstat (limited to 'drivers/tty/serial/m32r_sio_reg.h')
| -rw-r--r-- | drivers/tty/serial/m32r_sio_reg.h | 152 |
1 files changed, 152 insertions, 0 deletions
diff --git a/drivers/tty/serial/m32r_sio_reg.h b/drivers/tty/serial/m32r_sio_reg.h new file mode 100644 index 0000000..4671473 --- /dev/null +++ b/drivers/tty/serial/m32r_sio_reg.h @@ -0,0 +1,152 @@ +/* + * m32r_sio_reg.h + * + * Copyright (C) 1992, 1994 by Theodore Ts'o. + * Copyright (C) 2004 Hirokazu Takata <takata at linux-m32r.org> + * + * Redistribution of this file is permitted under the terms of the GNU + * Public License (GPL) + * + * These are the UART port assignments, expressed as offsets from the base + * register. These assignments should hold for any serial port based on + * a 8250, 16450, or 16550(A). + */ + +#ifndef _M32R_SIO_REG_H +#define _M32R_SIO_REG_H + + +#ifdef CONFIG_SERIAL_M32R_PLDSIO + +#define SIOCR 0x000 +#define SIOMOD0 0x002 +#define SIOMOD1 0x004 +#define SIOSTS 0x006 +#define SIOTRCR 0x008 +#define SIOBAUR 0x00a +// #define SIORBAUR 0x018 +#define SIOTXB 0x00c +#define SIORXB 0x00e + +#define UART_RX ((unsigned long) PLD_ESIO0RXB) + /* In: Receive buffer (DLAB=0) */ +#define UART_TX ((unsigned long) PLD_ESIO0TXB) + /* Out: Transmit buffer (DLAB=0) */ +#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ +#define UART_TRG 0 /* (LCR=BF) FCTR bit 7 selects Rx or Tx + * In: Fifo count + * Out: Fifo custom trigger levels + * XR16C85x only */ + +#define UART_DLM 0 /* Out: Divisor Latch High (DLAB=1) */ +#define UART_IER ((unsigned long) PLD_ESIO0INTCR) + /* Out: Interrupt Enable Register */ +#define UART_FCTR 0 /* (LCR=BF) Feature Control Register + * XR16C85x only */ + +#define UART_IIR 0 /* In: Interrupt ID Register */ +#define UART_FCR 0 /* Out: FIFO Control Register */ +#define UART_EFR 0 /* I/O: Extended Features Register */ + /* (DLAB=1, 16C660 only) */ + +#define UART_LCR 0 /* Out: Line Control Register */ +#define UART_MCR 0 /* Out: Modem Control Register */ +#define UART_LSR ((unsigned long) PLD_ESIO0STS) + /* In: Line Status Register */ +#define UART_MSR 0 /* In: Modem Status Register */ +#define UART_SCR 0 /* I/O: Scratch Register */ +#define UART_EMSR 0 /* (LCR=BF) Extended Mode Select Register + * FCTR bit 6 selects SCR or EMSR + * XR16c85x only */ + +#else /* not CONFIG_SERIAL_M32R_PLDSIO */ + +#define SIOCR 0x000 +#define SIOMOD0 0x004 +#define SIOMOD1 0x008 +#define SIOSTS 0x00c +#define SIOTRCR 0x010 +#define SIOBAUR 0x014 +#define SIORBAUR 0x018 +#define SIOTXB 0x01c +#define SIORXB 0x020 + +#define UART_RX M32R_SIO0_RXB_PORTL /* In: Receive buffer (DLAB=0) */ +#define UART_TX M32R_SIO0_TXB_PORTL /* Out: Transmit buffer (DLAB=0) */ +#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ +#define UART_TRG 0 /* (LCR=BF) FCTR bit 7 selects Rx or Tx + * In: Fifo count + * Out: Fifo custom trigger levels + * XR16C85x only */ + +#define UART_DLM 0 /* Out: Divisor Latch High (DLAB=1) */ +#define UART_IER M32R_SIO0_TRCR_PORTL /* Out: Interrupt Enable Register */ +#define UART_FCTR 0 /* (LCR=BF) Feature Control Register + * XR16C85x only */ + +#define UART_IIR 0 /* In: Interrupt ID Register */ +#define UART_FCR 0 /* Out: FIFO Control Register */ +#define UART_EFR 0 /* I/O: Extended Features Register */ + /* (DLAB=1, 16C660 only) */ + +#define UART_LCR 0 /* Out: Line Control Register */ +#define UART_MCR 0 /* Out: Modem Control Register */ +#define UART_LSR M32R_SIO0_STS_PORTL /* In: Line Status Register */ +#define UART_MSR 0 /* In: Modem Status Register */ +#define UART_SCR 0 /* I/O: Scratch Register */ +#define UART_EMSR 0 /* (LCR=BF) Extended Mode Select Register + * FCTR bit 6 selects SCR or EMSR + * XR16c85x only */ + +#endif /* CONFIG_SERIAL_M32R_PLDSIO */ + +#define UART_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) + +/* + * These are the definitions for the Line Control Register + * + * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting + * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. + */ +#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ +#define UART_LCR_SBC 0x40 /* Set break control */ +#define UART_LCR_SPAR 0x20 /* Stick parity (?) */ +#define UART_LCR_EPAR 0x10 /* Even parity select */ +#define UART_LCR_PARITY 0x08 /* Parity Enable */ +#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */ +#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */ +#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */ +#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */ +#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ + +/* + * These are the definitions for the Line Status Register + */ +#define UART_LSR_TEMT 0x02 /* Transmitter empty */ +#define UART_LSR_THRE 0x01 /* Transmit-hold-register empty */ +#define UART_LSR_BI 0x00 /* Break interrupt indicator */ +#define UART_LSR_FE 0x80 /* Frame error indicator */ +#define UART_LSR_PE 0x40 /* Parity error indicator */ +#define UART_LSR_OE 0x20 /* Overrun error indicator */ +#define UART_LSR_DR 0x04 /* Receiver data ready */ + +/* + * These are the definitions for the Interrupt Identification Register + */ +#define UART_IIR_NO_INT 0x01 /* No interrupts pending */ +#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ + +#define UART_IIR_MSI 0x00 /* Modem status interrupt */ +#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ +#define UART_IIR_RDI 0x04 /* Receiver data interrupt */ +#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ + +/* + * These are the definitions for the Interrupt Enable Register + */ +#define UART_IER_MSI 0x00 /* Enable Modem status interrupt */ +#define UART_IER_RLSI 0x08 /* Enable receiver line status interrupt */ +#define UART_IER_THRI 0x03 /* Enable Transmitter holding register int. */ +#define UART_IER_RDI 0x04 /* Enable receiver data interrupt */ + +#endif /* _M32R_SIO_REG_H */ |
