diff options
Diffstat (limited to 'drivers/staging/rtl8723bs/include/Hal8723BPwrSeq.h')
| -rw-r--r-- | drivers/staging/rtl8723bs/include/Hal8723BPwrSeq.h | 232 |
1 files changed, 232 insertions, 0 deletions
diff --git a/drivers/staging/rtl8723bs/include/Hal8723BPwrSeq.h b/drivers/staging/rtl8723bs/include/Hal8723BPwrSeq.h new file mode 100644 index 0000000..796449c --- /dev/null +++ b/drivers/staging/rtl8723bs/include/Hal8723BPwrSeq.h @@ -0,0 +1,232 @@ +#ifndef REALTEK_POWER_SEQUENCE_8723B +#define REALTEK_POWER_SEQUENCE_8723B + +#include "HalPwrSeqCmd.h" + +/* + Check document WM-20130815-JackieLau-RTL8723B_Power_Architecture v08.vsd + There are 6 HW Power States: + 0: POFF--Power Off + 1: PDN--Power Down + 2: CARDEMU--Card Emulation + 3: ACT--Active Mode + 4: LPS--Low Power State + 5: SUS--Suspend + + The transision from different states are defined below + TRANS_CARDEMU_TO_ACT + TRANS_ACT_TO_CARDEMU + TRANS_CARDEMU_TO_SUS + TRANS_SUS_TO_CARDEMU + TRANS_CARDEMU_TO_PDN + TRANS_ACT_TO_LPS + TRANS_LPS_TO_ACT + + TRANS_END +*/ +#define RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS 26 +#define RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS 15 +#define RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS 15 +#define RTL8723B_TRANS_SUS_TO_CARDEMU_STEPS 15 +#define RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS 15 +#define RTL8723B_TRANS_PDN_TO_CARDEMU_STEPS 15 +#define RTL8723B_TRANS_ACT_TO_LPS_STEPS 15 +#define RTL8723B_TRANS_LPS_TO_ACT_STEPS 15 +#define RTL8723B_TRANS_ACT_TO_SWLPS_STEPS 22 +#define RTL8723B_TRANS_SWLPS_TO_ACT_STEPS 15 +#define RTL8723B_TRANS_END_STEPS 1 + + +#define RTL8723B_TRANS_CARDEMU_TO_ACT \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \ + {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/ \ + {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/ \ + {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital , 1:isolation*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT4|BIT3|BIT2), 0},/* disable SW LPS 0x04[10]= 0 and WLSUS_EN 0x04[11]= 0*/ \ + {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 , BIT0},/* Disable USB suspend */ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1 power ready*/ \ + {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 , 0},/* Enable USB suspend */ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset 0x04[16]= 1*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]= 0*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT4|BIT3), 0},/* disable WL suspend*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0},/**/ \ + {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6, BIT6},/* Enable WL control XTAL setting*/ \ + {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/*Enable falling edge triggering interrupt*/\ + {0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/*Enable GPIO9 interrupt mode*/\ + {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Enable GPIO9 input mode*/\ + {0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*Enable HSISR GPIO[C:0] interrupt*/\ + {0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/*Enable HSISR GPIO9 interrupt*/\ + {0x0068, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, BIT3},/*For GPIO9 internal pull high setting by test chip*/\ + {0x0069, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6, BIT6},/*For GPIO9 internal pull high setting*/\ + + +#define RTL8723B_TRANS_ACT_TO_CARDEMU \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \ + {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Enable rising edge triggering interrupt*/ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset 0x04[16]= 1*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \ + {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6, 0},/* Enable BT control XTAL setting*/\ + {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5}, /*0x00[5] = 1b'1 analog Ips to digital , 1:isolation*/ \ + {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/\ + + +#define RTL8723B_TRANS_CARDEMU_TO_SUS \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ + +#define RTL8723B_TRANS_SUS_TO_CARDEMU \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/ + +#define RTL8723B_TRANS_CARDEMU_TO_CARDDIS \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, omments here*/ \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07 = 0x20 , SOP option to disable BG/MB*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2}, /*0x04[10] = 1, enable SW LPS*/ \ + {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ + +#define RTL8723B_TRANS_CARDDIS_TO_CARDEMU \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\ + {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \ + {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/ + + +#define RTL8723B_TRANS_CARDEMU_TO_PDN \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/ + +#define RTL8723B_TRANS_PDN_TO_CARDEMU \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/ + +#define RTL8723B_TRANS_ACT_TO_LPS \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \ + {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \ + {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ + {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ + {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ + {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/ \ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/ \ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \ + {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/ \ + {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/ \ + + +#define RTL8723B_TRANS_LPS_TO_ACT \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\ + {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\ + {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\ + {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*. 0x08[4] = 0 switch TSF to 40M*/\ + {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]= 0 TSF in 40M*/\ + {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6|BIT7, 0}, /*. 0x29[7:6] = 2b'00 enable BB clock*/\ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1*/\ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\ + {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ + + + #define RTL8723B_TRANS_ACT_TO_SWLPS \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0194, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*enable 32 K source*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*disable security engine*/ \ + {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x40},/*When driver enter Sus/ Disable, enable LOP for BT*/ \ + {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*reset dual TSF*/ \ + {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0},/*Reset CPU*/ \ + {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*Reset MCUFWDL register*/ \ + {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/ \ + {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1},/*Reset CPU IO Wrapper*/ \ + {0x0287, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*polling RXFF packet number = 0 */ \ + {0x0286, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/*polling RXDMA idle */ \ + {0x013D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*Clear FW RPWM interrupt */\ + {0x0139, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*Set FW RPWM interrupt source*/\ + {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4},/*switch TSF to 32K*/\ + {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/*polling TSF stable*/\ + {0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*Set FW LPS*/ \ + {0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0},/*polling FW LPS ready */ + + +#define RTL8723B_TRANS_SWLPS_TO_ACT \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0},/*switch TSF to 32K*/\ + {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/*polling TSF stable*/\ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1, enable security engine*/\ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\ + {0x06B7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x09}, /*. reset MAC rx state machine*/\ + {0x06B4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x86}, /*. reset MAC rx state machine*/\ + {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/* set CPU RAM code ready*/ \ + {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/ \ + {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0},/* Enable CPU*/ \ + {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*enable CPU IO Wrapper*/ \ + {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2},/* Enable CPU*/ \ + {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, BIT7},/*polling FW init ready */ \ + {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT6, BIT6},/*polling FW init ready */ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\ + {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ + +#define RTL8723B_TRANS_END \ + /* format */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \ + {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0}, + + +extern WLAN_PWR_CFG rtl8723B_power_on_flow[RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_radio_off_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_card_disable_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_card_enable_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_suspend_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_resume_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_hwpdn_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_enter_lps_flow[RTL8723B_TRANS_ACT_TO_LPS_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_leave_lps_flow[RTL8723B_TRANS_LPS_TO_ACT_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_enter_swlps_flow[RTL8723B_TRANS_ACT_TO_SWLPS_STEPS+RTL8723B_TRANS_END_STEPS]; +extern WLAN_PWR_CFG rtl8723B_leave_swlps_flow[RTL8723B_TRANS_SWLPS_TO_ACT_STEPS+RTL8723B_TRANS_END_STEPS]; +#endif |
