diff options
Diffstat (limited to 'drivers/serial/sh-sci.c')
| -rw-r--r-- | drivers/serial/sh-sci.c | 39 |
1 files changed, 35 insertions, 4 deletions
diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c index 053fca4..73440e2 100644 --- a/drivers/serial/sh-sci.c +++ b/drivers/serial/sh-sci.c @@ -4,6 +4,7 @@ * SuperH on-chip serial module support. (SCI with no FIFO / with FIFO) * * Copyright (C) 2002 - 2006 Paul Mundt + * Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007). * * based off of the old drivers/char/sh-sci.c by: * @@ -301,6 +302,38 @@ static void sci_init_pins_scif(struct uart_port* port, unsigned int cflag) } sci_out(port, SCFCR, fcr_val); } +#elif defined(CONFIG_CPU_SUBTYPE_SH7720) +static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag) +{ + unsigned int fcr_val = 0; + unsigned short data; + + if (cflag & CRTSCTS) { + /* enable RTS/CTS */ + if (port->mapbase == 0xa4430000) { /* SCIF0 */ + /* Clear PTCR bit 9-2; enable all scif pins but sck */ + data = ctrl_inw(PORT_PTCR); + ctrl_outw((data & 0xfc03), PORT_PTCR); + } else if (port->mapbase == 0xa4438000) { /* SCIF1 */ + /* Clear PVCR bit 9-2 */ + data = ctrl_inw(PORT_PVCR); + ctrl_outw((data & 0xfc03), PORT_PVCR); + } + fcr_val |= SCFCR_MCE; + } else { + if (port->mapbase == 0xa4430000) { /* SCIF0 */ + /* Clear PTCR bit 5-2; enable only tx and rx */ + data = ctrl_inw(PORT_PTCR); + ctrl_outw((data & 0xffc3), PORT_PTCR); + } else if (port->mapbase == 0xa4438000) { /* SCIF1 */ + /* Clear PVCR bit 5-2 */ + data = ctrl_inw(PORT_PVCR); + ctrl_outw((data & 0xffc3), PORT_PVCR); + } + } + sci_out(port, SCFCR, fcr_val); +} + #elif defined(CONFIG_CPU_SH3) /* For SH7705, SH7706, SH7707, SH7709, SH7709A, SH7729 */ static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag) @@ -1276,7 +1309,7 @@ static int __init sci_console_init(void) console_initcall(sci_console_init); #endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */ -#ifdef CONFIG_SH_KGDB +#ifdef CONFIG_SH_KGDB_CONSOLE /* * FIXME: Most of this can go away.. at the moment, we rely on * arch/sh/kernel/setup.c to do the command line parsing for kgdb, though @@ -1334,9 +1367,7 @@ int __init kgdb_console_setup(struct console *co, char *options) return uart_set_options(port, co, baud, parity, bits, flow); } -#endif /* CONFIG_SH_KGDB */ -#ifdef CONFIG_SH_KGDB_CONSOLE static struct console kgdb_console = { .name = "ttySC", .device = uart_console_device, @@ -1432,7 +1463,7 @@ static int __devinit sci_probe(struct platform_device *dev) #ifdef CONFIG_CPU_FREQ cpufreq_register_notifier(&sci_nb, CPUFREQ_TRANSITION_NOTIFIER); - dev_info(&dev->dev, "sci: CPU frequency notifier registered\n"); + dev_info(&dev->dev, "CPU frequency notifier registered\n"); #endif #ifdef CONFIG_SH_STANDARD_BIOS |
