diff options
Diffstat (limited to 'drivers/serial/crisv10.h')
| -rw-r--r-- | drivers/serial/crisv10.h | 136 |
1 files changed, 0 insertions, 136 deletions
diff --git a/drivers/serial/crisv10.h b/drivers/serial/crisv10.h deleted file mode 100644 index 4a23340..0000000 --- a/drivers/serial/crisv10.h +++ /dev/null @@ -1,136 +0,0 @@ -/* - * serial.h: Arch-dep definitions for the Etrax100 serial driver. - * - * Copyright (C) 1998, 1999, 2000 Axis Communications AB - */ - -#ifndef _ETRAX_SERIAL_H -#define _ETRAX_SERIAL_H - -#include <linux/circ_buf.h> -#include <asm/termios.h> - -/* Software state per channel */ - -#ifdef __KERNEL__ -/* - * This is our internal structure for each serial port's state. - * - * Many fields are paralleled by the structure used by the serial_struct - * structure. - * - * For definitions of the flags field, see tty.h - */ - -#define SERIAL_RECV_DESCRIPTORS 8 - -struct etrax_recv_buffer { - struct etrax_recv_buffer *next; - unsigned short length; - unsigned char error; - unsigned char pad; - - unsigned char buffer[0]; -}; - -struct e100_serial { - int baud; - volatile u8 *port; /* R_SERIALx_CTRL */ - u32 irq; /* bitnr in R_IRQ_MASK2 for dmaX_descr */ - - /* Output registers */ - volatile u8 *oclrintradr; /* adr to R_DMA_CHx_CLR_INTR */ - volatile u32 *ofirstadr; /* adr to R_DMA_CHx_FIRST */ - volatile u8 *ocmdadr; /* adr to R_DMA_CHx_CMD */ - const volatile u8 *ostatusadr; /* adr to R_DMA_CHx_STATUS */ - - /* Input registers */ - volatile u8 *iclrintradr; /* adr to R_DMA_CHx_CLR_INTR */ - volatile u32 *ifirstadr; /* adr to R_DMA_CHx_FIRST */ - volatile u8 *icmdadr; /* adr to R_DMA_CHx_CMD */ - volatile u32 *idescradr; /* adr to R_DMA_CHx_DESCR */ - - int flags; /* defined in tty.h */ - - u8 rx_ctrl; /* shadow for R_SERIALx_REC_CTRL */ - u8 tx_ctrl; /* shadow for R_SERIALx_TR_CTRL */ - u8 iseteop; /* bit number for R_SET_EOP for the input dma */ - int enabled; /* Set to 1 if the port is enabled in HW config */ - - u8 dma_out_enabled:1; /* Set to 1 if DMA should be used */ - u8 dma_in_enabled:1; /* Set to 1 if DMA should be used */ - - /* end of fields defined in rs_table[] in .c-file */ - u8 uses_dma_in; /* Set to 1 if DMA is used */ - u8 uses_dma_out; /* Set to 1 if DMA is used */ - u8 forced_eop; /* a fifo eop has been forced */ - int baud_base; /* For special baudrates */ - int custom_divisor; /* For special baudrates */ - struct etrax_dma_descr tr_descr; - struct etrax_dma_descr rec_descr[SERIAL_RECV_DESCRIPTORS]; - int cur_rec_descr; - - volatile int tr_running; /* 1 if output is running */ - - struct tty_struct *tty; - int read_status_mask; - int ignore_status_mask; - int x_char; /* xon/xoff character */ - int close_delay; - unsigned short closing_wait; - unsigned short closing_wait2; - unsigned long event; - unsigned long last_active; - int line; - int type; /* PORT_ETRAX */ - int count; /* # of fd on device */ - int blocked_open; /* # of blocked opens */ - struct circ_buf xmit; - struct etrax_recv_buffer *first_recv_buffer; - struct etrax_recv_buffer *last_recv_buffer; - unsigned int recv_cnt; - unsigned int max_recv_cnt; - - struct work_struct work; - struct async_icount icount; /* error-statistics etc.*/ - struct ktermios normal_termios; - struct ktermios callout_termios; -#ifdef DECLARE_WAITQUEUE - wait_queue_head_t open_wait; - wait_queue_head_t close_wait; -#else - struct wait_queue *open_wait; - struct wait_queue *close_wait; -#endif - - unsigned long char_time_usec; /* The time for 1 char, in usecs */ - unsigned long flush_time_usec; /* How often we should flush */ - unsigned long last_tx_active_usec; /* Last tx usec in the jiffies */ - unsigned long last_tx_active; /* Last tx time in jiffies */ - unsigned long last_rx_active_usec; /* Last rx usec in the jiffies */ - unsigned long last_rx_active; /* Last rx time in jiffies */ - - int break_detected_cnt; - int errorcode; - -#ifdef CONFIG_ETRAX_RS485 - struct rs485_control rs485; /* RS-485 support */ -#endif -}; - -/* this PORT is not in the standard serial.h. it's not actually used for - * anything since we only have one type of async serial-port anyway in this - * system. - */ - -#define PORT_ETRAX 1 - -/* - * Events are used to schedule things to happen at timer-interrupt - * time, instead of at rs interrupt time. - */ -#define RS_EVENT_WRITE_WAKEUP 0 - -#endif /* __KERNEL__ */ - -#endif /* !_ETRAX_SERIAL_H */ |
