diff options
Diffstat (limited to 'drivers/serial/bfin_5xx.c')
| -rw-r--r-- | drivers/serial/bfin_5xx.c | 282 |
1 files changed, 190 insertions, 92 deletions
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c index f9b5a72..d86123e 100644 --- a/drivers/serial/bfin_5xx.c +++ b/drivers/serial/bfin_5xx.c @@ -63,7 +63,6 @@ static int kgdboc_break_enabled; #define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT) #define DMA_RX_FLUSH_JIFFIES (HZ / 50) -#define CTS_CHECK_JIFFIES (HZ / 50) #ifdef CONFIG_SERIAL_BFIN_DMA static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart); @@ -71,10 +70,65 @@ static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart); static void bfin_serial_tx_chars(struct bfin_serial_port *uart); #endif -static void bfin_serial_mctrl_check(struct bfin_serial_port *uart); - static void bfin_serial_reset_irda(struct uart_port *port); +#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \ + defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS) +static unsigned int bfin_serial_get_mctrl(struct uart_port *port) +{ + struct bfin_serial_port *uart = (struct bfin_serial_port *)port; + if (uart->cts_pin < 0) + return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; + + /* CTS PIN is negative assertive. */ + if (UART_GET_CTS(uart)) + return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; + else + return TIOCM_DSR | TIOCM_CAR; +} + +static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct bfin_serial_port *uart = (struct bfin_serial_port *)port; + if (uart->rts_pin < 0) + return; + + /* RTS PIN is negative assertive. */ + if (mctrl & TIOCM_RTS) + UART_ENABLE_RTS(uart); + else + UART_DISABLE_RTS(uart); +} + +/* + * Handle any change of modem status signal. + */ +static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id) +{ + struct bfin_serial_port *uart = dev_id; + unsigned int status; + + status = bfin_serial_get_mctrl(&uart->port); + uart_handle_cts_change(&uart->port, status & TIOCM_CTS); +#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS + uart->scts = 1; + UART_CLEAR_SCTS(uart); + UART_CLEAR_IER(uart, EDSSI); +#endif + + return IRQ_HANDLED; +} +#else +static unsigned int bfin_serial_get_mctrl(struct uart_port *port) +{ + return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; +} + +static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ +} +#endif + /* * interrupts are disabled on entry */ @@ -111,6 +165,13 @@ static void bfin_serial_start_tx(struct uart_port *port) struct bfin_serial_port *uart = (struct bfin_serial_port *)port; struct tty_struct *tty = uart->port.info->port.tty; +#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS + if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) { + uart->scts = 0; + uart_handle_cts_change(&uart->port, uart->scts); + } +#endif + /* * To avoid losting RX interrupt, we reset IR function * before sending data. @@ -264,12 +325,6 @@ static void bfin_serial_tx_chars(struct bfin_serial_port *uart) { struct circ_buf *xmit = &uart->port.info->xmit; - /* - * Check the modem control lines before - * transmitting anything. - */ - bfin_serial_mctrl_check(uart); - if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) { #ifdef CONFIG_BF54x /* Clear TFI bit */ @@ -312,6 +367,12 @@ static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id) { struct bfin_serial_port *uart = dev_id; +#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS + if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) { + uart->scts = 0; + uart_handle_cts_change(&uart->port, uart->scts); + } +#endif spin_lock(&uart->port.lock); if (UART_GET_LSR(uart) & THRE) bfin_serial_tx_chars(uart); @@ -328,12 +389,6 @@ static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart) uart->tx_done = 0; - /* - * Check the modem control lines before - * transmitting anything. - */ - bfin_serial_mctrl_check(uart); - if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) { uart->tx_count = 0; uart->tx_done = 1; @@ -448,6 +503,13 @@ static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id) struct bfin_serial_port *uart = dev_id; struct circ_buf *xmit = &uart->port.info->xmit; +#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS + if (uart->scts && !(bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) { + uart->scts = 0; + uart_handle_cts_change(&uart->port, uart->scts); + } +#endif + spin_lock(&uart->port.lock); if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) { disable_dma(uart->tx_dma_channel); @@ -496,61 +558,6 @@ static unsigned int bfin_serial_tx_empty(struct uart_port *port) return 0; } -static unsigned int bfin_serial_get_mctrl(struct uart_port *port) -{ -#ifdef CONFIG_SERIAL_BFIN_CTSRTS - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - if (uart->cts_pin < 0) - return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; - - if (UART_GET_CTS(uart)) - return TIOCM_DSR | TIOCM_CAR; - else -#endif - return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; -} - -static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ -#ifdef CONFIG_SERIAL_BFIN_CTSRTS - struct bfin_serial_port *uart = (struct bfin_serial_port *)port; - if (uart->rts_pin < 0) - return; - - if (mctrl & TIOCM_RTS) - UART_CLEAR_RTS(uart); - else - UART_SET_RTS(uart); -#endif -} - -/* - * Handle any change of modem status signal since we were last called. - */ -static void bfin_serial_mctrl_check(struct bfin_serial_port *uart) -{ -#ifdef CONFIG_SERIAL_BFIN_CTSRTS - unsigned int status; - struct uart_info *info = uart->port.info; - struct tty_struct *tty = info->port.tty; - - status = bfin_serial_get_mctrl(&uart->port); - uart_handle_cts_change(&uart->port, status & TIOCM_CTS); - if (!(status & TIOCM_CTS)) { - tty->hw_stopped = 1; - uart->cts_timer.data = (unsigned long)(uart); - uart->cts_timer.function = (void *)bfin_serial_mctrl_check; - uart->cts_timer.expires = jiffies + CTS_CHECK_JIFFIES; - add_timer(&(uart->cts_timer)); - } else { - tty->hw_stopped = 0; - } -#endif -} - -/* - * Interrupts are always disabled. - */ static void bfin_serial_break_ctl(struct uart_port *port, int break_state) { struct bfin_serial_port *uart = (struct bfin_serial_port *)port; @@ -606,7 +613,7 @@ static int bfin_serial_startup(struct uart_port *port) uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES; add_timer(&(uart->rx_dma_timer)); #else -#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \ +# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE) if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled) kgdboc_break_enabled = 0; @@ -661,11 +668,50 @@ static int bfin_serial_startup(struct uart_port *port) } } # endif -#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \ +# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE) } # endif #endif + +#ifdef CONFIG_SERIAL_BFIN_CTSRTS + if (uart->cts_pin >= 0) { + if (request_irq(gpio_to_irq(uart->cts_pin), + bfin_serial_mctrl_cts_int, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | + IRQF_DISABLED, "BFIN_UART_CTS", uart)) { + uart->cts_pin = -1; + pr_info("Unable to attach BlackFin UART CTS interrupt.\ + So, disable it.\n"); + } + } + if (uart->rts_pin >= 0) { + gpio_request(uart->rts_pin, DRIVER_NAME); + gpio_direction_output(uart->rts_pin, 0); + } +#endif +#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS + if (request_irq(uart->status_irq, + bfin_serial_mctrl_cts_int, + IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) { + pr_info("Unable to attach BlackFin UART Modem \ + Status interrupt.\n"); + } + + if (uart->cts_pin >= 0) { + gpio_request(uart->cts_pin, DRIVER_NAME); + gpio_direction_output(uart->cts_pin, 1); + } + if (uart->rts_pin >= 0) { + gpio_request(uart->rts_pin, DRIVER_NAME); + gpio_direction_output(uart->rts_pin, 0); + } + + /* CTS RTS PINs are negative assertive. */ + UART_PUT_MCR(uart, ACTS); + UART_SET_IER(uart, EDSSI); +#endif + UART_SET_IER(uart, ERBFI); return 0; } @@ -699,6 +745,21 @@ static void bfin_serial_shutdown(struct uart_port *port) free_irq(uart->port.irq, uart); free_irq(uart->port.irq+1, uart); #endif + +#ifdef CONFIG_SERIAL_BFIN_CTSRTS + if (uart->cts_pin >= 0) + free_irq(gpio_to_irq(uart->cts_pin), uart); + if (uart->rts_pin >= 0) + gpio_free(uart->rts_pin); +#endif +#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS + if (uart->cts_pin >= 0) + gpio_free(uart->cts_pin); + if (uart->rts_pin >= 0) + gpio_free(uart->rts_pin); + if (UART_GET_IER(uart) && EDSSI) + free_irq(uart->status_irq, uart); +#endif } static void @@ -864,6 +925,20 @@ static void bfin_serial_set_ldisc(struct uart_port *port) } } +static void bfin_serial_reset_irda(struct uart_port *port) +{ + int line = port->line; + unsigned short val; + + val = UART_GET_GCTL(&bfin_serial_ports[line]); + val &= ~(IREN | RPOLC); + UART_PUT_GCTL(&bfin_serial_ports[line], val); + SSYNC(); + val |= (IREN | RPOLC); + UART_PUT_GCTL(&bfin_serial_ports[line], val); + SSYNC(); +} + #ifdef CONFIG_CONSOLE_POLL static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr) { @@ -909,20 +984,6 @@ static int bfin_kgdboc_port_startup(struct uart_port *port) } #endif -static void bfin_serial_reset_irda(struct uart_port *port) -{ - int line = port->line; - unsigned short val; - - val = UART_GET_GCTL(&bfin_serial_ports[line]); - val &= ~(IREN | RPOLC); - UART_PUT_GCTL(&bfin_serial_ports[line], val); - SSYNC(); - val |= (IREN | RPOLC); - UART_PUT_GCTL(&bfin_serial_ports[line], val); - SSYNC(); -} - static struct uart_ops bfin_serial_pops = { .tx_empty = bfin_serial_tx_empty, .set_mctrl = bfin_serial_set_mctrl, @@ -952,6 +1013,39 @@ static struct uart_ops bfin_serial_pops = { #endif }; +static void __init bfin_serial_hw_init(void) +{ +#ifdef CONFIG_SERIAL_BFIN_UART0 + peripheral_request(P_UART0_TX, DRIVER_NAME); + peripheral_request(P_UART0_RX, DRIVER_NAME); +#endif + +#ifdef CONFIG_SERIAL_BFIN_UART1 + peripheral_request(P_UART1_TX, DRIVER_NAME); + peripheral_request(P_UART1_RX, DRIVER_NAME); + +# if defined(CONFIG_BFIN_UART1_CTSRTS) && defined(CONFIG_BF54x) + peripheral_request(P_UART1_RTS, DRIVER_NAME); + peripheral_request(P_UART1_CTS, DRIVER_NAME); +# endif +#endif + +#ifdef CONFIG_SERIAL_BFIN_UART2 + peripheral_request(P_UART2_TX, DRIVER_NAME); + peripheral_request(P_UART2_RX, DRIVER_NAME); +#endif + +#ifdef CONFIG_SERIAL_BFIN_UART3 + peripheral_request(P_UART3_TX, DRIVER_NAME); + peripheral_request(P_UART3_RX, DRIVER_NAME); + +# if defined(CONFIG_BFIN_UART3_CTSRTS) && defined(CONFIG_BF54x) + peripheral_request(P_UART3_RTS, DRIVER_NAME); + peripheral_request(P_UART3_CTS, DRIVER_NAME); +# endif +#endif +} + static void __init bfin_serial_init_ports(void) { static int first = 1; @@ -961,6 +1055,8 @@ static void __init bfin_serial_init_ports(void) return; first = 0; + bfin_serial_hw_init(); + for (i = 0; i < nr_active_ports; i++) { bfin_serial_ports[i].port.uartclk = get_sclk(); bfin_serial_ports[i].port.fifosize = BFIN_UART_TX_FIFO_SIZE; @@ -973,6 +1069,8 @@ static void __init bfin_serial_init_ports(void) bfin_serial_resource[i].uart_base_addr; bfin_serial_ports[i].port.irq = bfin_serial_resource[i].uart_irq; + bfin_serial_ports[i].status_irq = + bfin_serial_resource[i].uart_status_irq; bfin_serial_ports[i].port.flags = UPF_BOOT_AUTOCONF; #ifdef CONFIG_SERIAL_BFIN_DMA bfin_serial_ports[i].tx_done = 1; @@ -983,16 +1081,14 @@ static void __init bfin_serial_init_ports(void) bfin_serial_resource[i].uart_rx_dma_channel; init_timer(&(bfin_serial_ports[i].rx_dma_timer)); #endif -#ifdef CONFIG_SERIAL_BFIN_CTSRTS - init_timer(&(bfin_serial_ports[i].cts_timer)); +#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \ + defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS) bfin_serial_ports[i].cts_pin = bfin_serial_resource[i].uart_cts_pin; bfin_serial_ports[i].rts_pin = bfin_serial_resource[i].uart_rts_pin; #endif - bfin_serial_hw_init(&bfin_serial_ports[i]); } - } #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK) @@ -1049,7 +1145,8 @@ bfin_serial_console_setup(struct console *co, char *options) int baud = 57600; int bits = 8; int parity = 'n'; -# ifdef CONFIG_SERIAL_BFIN_CTSRTS +# if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \ + defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS) int flow = 'r'; # else int flow = 'n'; @@ -1246,7 +1343,8 @@ static int bfin_serial_remove(struct platform_device *dev) continue; uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port); bfin_serial_ports[i].port.dev = NULL; -#ifdef CONFIG_SERIAL_BFIN_CTSRTS +#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \ + defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS) gpio_free(bfin_serial_ports[i].cts_pin); gpio_free(bfin_serial_ports[i].rts_pin); #endif |
