diff options
Diffstat (limited to 'drivers/scsi/Kconfig')
| -rw-r--r-- | drivers/scsi/Kconfig | 68 |
1 files changed, 25 insertions, 43 deletions
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig index 9c9f162..84c42c4 100644 --- a/drivers/scsi/Kconfig +++ b/drivers/scsi/Kconfig @@ -229,7 +229,7 @@ config SCSI_FC_ATTRS config SCSI_ISCSI_ATTRS tristate "iSCSI Transport Attributes" - depends on SCSI + depends on SCSI && NET help If you wish to export transport-specific information about each attached iSCSI device to sysfs, say Y. @@ -247,6 +247,30 @@ endmenu menu "SCSI low-level drivers" depends on SCSI!=n +config ISCSI_TCP + tristate "iSCSI Initiator over TCP/IP" + depends on SCSI && INET + select CRYPTO + select CRYPTO_MD5 + select CRYPTO_CRC32C + select SCSI_ISCSI_ATTRS + help + The iSCSI Driver provides a host with the ability to access storage + through an IP network. The driver uses the iSCSI protocol to transport + SCSI requests and responses over a TCP/IP network between the host + (the "initiator") and "targets". Architecturally, the iSCSI driver + combines with the host's TCP/IP stack, network drivers, and Network + Interface Card (NIC) to provide the same functions as a SCSI or a + Fibre Channel (FC) adapter driver with a Host Bus Adapter (HBA). + + To compile this driver as a module, choose M here: the + module will be called iscsi_tcp. + + The userspace component needed to initialize the driver, documentation, + and sample configuration files can be found here: + + http://linux-iscsi.sf.net + config SGIWD93_SCSI tristate "SGI WD93C93 SCSI Driver" depends on SGI_IP22 && SCSI @@ -596,19 +620,6 @@ config SCSI_OMIT_FLASHPOINT substantial, so users of MultiMaster Host Adapters may wish to omit it. -# -# This is marked broken because it uses over 4kB of stack in -# just two routines: -# 2076 CpqTsProcessIMQEntry -# 2052 PeekIMQEntry -# -config SCSI_CPQFCTS - tristate "Compaq Fibre Channel 64-bit/66Mhz HBA support" - depends on PCI && SCSI && BROKEN - help - Say Y here to compile in support for the Compaq StorageWorks Fibre - Channel 64-bit/66Mhz Host Bus Adapter. - config SCSI_DMX3191D tristate "DMX3191D SCSI support" depends on PCI && SCSI @@ -1284,27 +1295,6 @@ config SCSI_QLOGIC_FAS To compile this driver as a module, choose M here: the module will be called qlogicfas. -config SCSI_QLOGIC_ISP - tristate "Qlogic ISP SCSI support (old driver)" - depends on PCI && SCSI && BROKEN - ---help--- - This driver works for all QLogic PCI SCSI host adapters (IQ-PCI, - IQ-PCI-10, IQ_PCI-D) except for the PCI-basic card. (This latter - card is supported by the "AM53/79C974 PCI SCSI" driver.) - - If you say Y here, make sure to choose "BIOS" at the question "PCI - access mode". - - Please read the file <file:Documentation/scsi/qlogicisp.txt>. You - should also read the SCSI-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. - - To compile this driver as a module, choose M here: the - module will be called qlogicisp. - - These days the hardware is also supported by the more modern qla1280 - driver. In doubt use that one instead of qlogicisp. - config SCSI_QLOGIC_FC tristate "Qlogic ISP FC SCSI support" depends on PCI && SCSI @@ -1331,14 +1321,6 @@ config SCSI_QLOGIC_1280 To compile this driver as a module, choose M here: the module will be called qla1280. -config SCSI_QLOGIC_1280_1040 - bool "Qlogic QLA 1020/1040 SCSI support" - depends on SCSI_QLOGIC_1280 && SCSI_QLOGIC_ISP!=y - help - Say Y here if you have a QLogic ISP1020/1040 SCSI host adapter and - do not want to use the old driver. This option enables support in - the qla1280 driver for those host adapters. - config SCSI_QLOGICPTI tristate "PTI Qlogic, ISP Driver" depends on SBUS && SCSI |
