diff options
Diffstat (limited to 'drivers/net/wireless/iwlwifi/iwl-fw-file.h')
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-fw-file.h | 308 |
1 files changed, 308 insertions, 0 deletions
diff --git a/drivers/net/wireless/iwlwifi/iwl-fw-file.h b/drivers/net/wireless/iwlwifi/iwl-fw-file.h index 401f7be..f2a047f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-fw-file.h +++ b/drivers/net/wireless/iwlwifi/iwl-fw-file.h @@ -131,6 +131,9 @@ enum iwl_ucode_tlv_type { IWL_UCODE_TLV_API_CHANGES_SET = 29, IWL_UCODE_TLV_ENABLED_CAPABILITIES = 30, IWL_UCODE_TLV_N_SCAN_CHANNELS = 31, + IWL_UCODE_TLV_SEC_RT_USNIFFER = 34, + IWL_UCODE_TLV_FW_DBG_DEST = 38, + IWL_UCODE_TLV_FW_DBG_CONF = 39, }; struct iwl_ucode_tlv { @@ -179,4 +182,309 @@ struct iwl_ucode_capa { __le32 api_capa; } __packed; +/** + * enum iwl_ucode_tlv_flag - ucode API flags + * @IWL_UCODE_TLV_FLAGS_PAN: This is PAN capable microcode; this previously + * was a separate TLV but moved here to save space. + * @IWL_UCODE_TLV_FLAGS_NEWSCAN: new uCode scan behaviour on hidden SSID, + * treats good CRC threshold as a boolean + * @IWL_UCODE_TLV_FLAGS_MFP: This uCode image supports MFP (802.11w). + * @IWL_UCODE_TLV_FLAGS_P2P: This uCode image supports P2P. + * @IWL_UCODE_TLV_FLAGS_DW_BC_TABLE: The SCD byte count table is in DWORDS + * @IWL_UCODE_TLV_FLAGS_UAPSD_SUPPORT: This uCode image supports uAPSD + * @IWL_UCODE_TLV_FLAGS_SHORT_BL: 16 entries of black list instead of 64 in scan + * offload profile config command. + * @IWL_UCODE_TLV_FLAGS_D3_6_IPV6_ADDRS: D3 image supports up to six + * (rather than two) IPv6 addresses + * @IWL_UCODE_TLV_FLAGS_NO_BASIC_SSID: not sending a probe with the SSID element + * from the probe request template. + * @IWL_UCODE_TLV_FLAGS_NEW_NSOFFL_SMALL: new NS offload (small version) + * @IWL_UCODE_TLV_FLAGS_NEW_NSOFFL_LARGE: new NS offload (large version) + * @IWL_UCODE_TLV_FLAGS_P2P_PM: P2P client supports PM as a stand alone MAC + * @IWL_UCODE_TLV_FLAGS_P2P_BSS_PS_DCM: support power save on BSS station and + * P2P client interfaces simultaneously if they are in different bindings. + * @IWL_UCODE_TLV_FLAGS_P2P_BSS_PS_SCM: support power save on BSS station and + * P2P client interfaces simultaneously if they are in same bindings. + * @IWL_UCODE_TLV_FLAGS_UAPSD_SUPPORT: General support for uAPSD + * @IWL_UCODE_TLV_FLAGS_P2P_PS_UAPSD: P2P client supports uAPSD power save + * @IWL_UCODE_TLV_FLAGS_BCAST_FILTERING: uCode supports broadcast filtering. + * @IWL_UCODE_TLV_FLAGS_GO_UAPSD: AP/GO interfaces support uAPSD clients + * @IWL_UCODE_TLV_FLAGS_EBS_SUPPORT: this uCode image supports EBS. + */ +enum iwl_ucode_tlv_flag { + IWL_UCODE_TLV_FLAGS_PAN = BIT(0), + IWL_UCODE_TLV_FLAGS_NEWSCAN = BIT(1), + IWL_UCODE_TLV_FLAGS_MFP = BIT(2), + IWL_UCODE_TLV_FLAGS_P2P = BIT(3), + IWL_UCODE_TLV_FLAGS_DW_BC_TABLE = BIT(4), + IWL_UCODE_TLV_FLAGS_SHORT_BL = BIT(7), + IWL_UCODE_TLV_FLAGS_D3_6_IPV6_ADDRS = BIT(10), + IWL_UCODE_TLV_FLAGS_NO_BASIC_SSID = BIT(12), + IWL_UCODE_TLV_FLAGS_NEW_NSOFFL_SMALL = BIT(15), + IWL_UCODE_TLV_FLAGS_NEW_NSOFFL_LARGE = BIT(16), + IWL_UCODE_TLV_FLAGS_P2P_PM = BIT(21), + IWL_UCODE_TLV_FLAGS_BSS_P2P_PS_DCM = BIT(22), + IWL_UCODE_TLV_FLAGS_BSS_P2P_PS_SCM = BIT(23), + IWL_UCODE_TLV_FLAGS_UAPSD_SUPPORT = BIT(24), + IWL_UCODE_TLV_FLAGS_EBS_SUPPORT = BIT(25), + IWL_UCODE_TLV_FLAGS_P2P_PS_UAPSD = BIT(26), + IWL_UCODE_TLV_FLAGS_BCAST_FILTERING = BIT(29), + IWL_UCODE_TLV_FLAGS_GO_UAPSD = BIT(30), +}; + +/** + * enum iwl_ucode_tlv_api - ucode api + * @IWL_UCODE_TLV_API_WOWLAN_CONFIG_TID: wowlan config includes tid field. + * @IWL_UCODE_TLV_CAPA_EXTENDED_BEACON: Support Extended beacon notification + * @IWL_UCODE_TLV_API_BT_COEX_SPLIT: new API for BT Coex + * @IWL_UCODE_TLV_API_CSA_FLOW: ucode can do unbind-bind flow for CSA. + * @IWL_UCODE_TLV_API_DISABLE_STA_TX: ucode supports tx_disable bit. + * @IWL_UCODE_TLV_API_LMAC_SCAN: This ucode uses LMAC unified scan API. + * @IWL_UCODE_TLV_API_SF_NO_DUMMY_NOTIF: ucode supports disabling dummy notif. + * @IWL_UCODE_TLV_API_FRAGMENTED_SCAN: This ucode supports active dwell time + * longer than the passive one, which is essential for fragmented scan. + */ +enum iwl_ucode_tlv_api { + IWL_UCODE_TLV_API_WOWLAN_CONFIG_TID = BIT(0), + IWL_UCODE_TLV_CAPA_EXTENDED_BEACON = BIT(1), + IWL_UCODE_TLV_API_BT_COEX_SPLIT = BIT(3), + IWL_UCODE_TLV_API_CSA_FLOW = BIT(4), + IWL_UCODE_TLV_API_DISABLE_STA_TX = BIT(5), + IWL_UCODE_TLV_API_LMAC_SCAN = BIT(6), + IWL_UCODE_TLV_API_SF_NO_DUMMY_NOTIF = BIT(7), + IWL_UCODE_TLV_API_FRAGMENTED_SCAN = BIT(8), +}; + +/** + * enum iwl_ucode_tlv_capa - ucode capabilities + * @IWL_UCODE_TLV_CAPA_D0I3_SUPPORT: supports D0i3 + * @IWL_UCODE_TLV_CAPA_LAR_SUPPORT: supports Location Aware Regulatory + * @IWL_UCODE_TLV_CAPA_UMAC_SCAN: supports UMAC scan. + * @IWL_UCODE_TLV_CAPA_TDLS_SUPPORT: support basic TDLS functionality + * @IWL_UCODE_TLV_CAPA_TXPOWER_INSERTION_SUPPORT: supports insertion of current + * tx power value into TPC Report action frame and Link Measurement Report + * action frame + * @IWL_UCODE_TLV_CAPA_DS_PARAM_SET_IE_SUPPORT: supports updating current + * channel in DS parameter set element in probe requests. + * @IWL_UCODE_TLV_CAPA_WFA_TPC_REP_IE_SUPPORT: supports adding TPC Report IE in + * probe requests. + * @IWL_UCODE_TLV_CAPA_QUIET_PERIOD_SUPPORT: supports Quiet Period requests + * @IWL_UCODE_TLV_CAPA_DQA_SUPPORT: supports dynamic queue allocation (DQA), + * which also implies support for the scheduler configuration command + * @IWL_UCODE_TLV_CAPA_TDLS_CHANNEL_SWITCH: supports TDLS channel switching + * @IWL_UCODE_TLV_CAPA_HOTSPOT_SUPPORT: supports Hot Spot Command + */ +enum iwl_ucode_tlv_capa { + IWL_UCODE_TLV_CAPA_D0I3_SUPPORT = BIT(0), + IWL_UCODE_TLV_CAPA_LAR_SUPPORT = BIT(1), + IWL_UCODE_TLV_CAPA_UMAC_SCAN = BIT(2), + IWL_UCODE_TLV_CAPA_TDLS_SUPPORT = BIT(6), + IWL_UCODE_TLV_CAPA_TXPOWER_INSERTION_SUPPORT = BIT(8), + IWL_UCODE_TLV_CAPA_DS_PARAM_SET_IE_SUPPORT = BIT(9), + IWL_UCODE_TLV_CAPA_WFA_TPC_REP_IE_SUPPORT = BIT(10), + IWL_UCODE_TLV_CAPA_QUIET_PERIOD_SUPPORT = BIT(11), + IWL_UCODE_TLV_CAPA_DQA_SUPPORT = BIT(12), + IWL_UCODE_TLV_CAPA_TDLS_CHANNEL_SWITCH = BIT(13), + IWL_UCODE_TLV_CAPA_HOTSPOT_SUPPORT = BIT(18), +}; + +/* The default calibrate table size if not specified by firmware file */ +#define IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE 18 +#define IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE 19 +#define IWL_MAX_PHY_CALIBRATE_TBL_SIZE 253 + +/* The default max probe length if not specified by the firmware file */ +#define IWL_DEFAULT_MAX_PROBE_LENGTH 200 + +/* + * For 16.0 uCode and above, there is no differentiation between sections, + * just an offset to the HW address. + */ +#define IWL_UCODE_SECTION_MAX 12 +#define IWL_API_ARRAY_SIZE 1 +#define IWL_CAPABILITIES_ARRAY_SIZE 1 +#define CPU1_CPU2_SEPARATOR_SECTION 0xFFFFCCCC + +/* uCode version contains 4 values: Major/Minor/API/Serial */ +#define IWL_UCODE_MAJOR(ver) (((ver) & 0xFF000000) >> 24) +#define IWL_UCODE_MINOR(ver) (((ver) & 0x00FF0000) >> 16) +#define IWL_UCODE_API(ver) (((ver) & 0x0000FF00) >> 8) +#define IWL_UCODE_SERIAL(ver) ((ver) & 0x000000FF) + +/* + * Calibration control struct. + * Sent as part of the phy configuration command. + * @flow_trigger: bitmap for which calibrations to perform according to + * flow triggers. + * @event_trigger: bitmap for which calibrations to perform according to + * event triggers. + */ +struct iwl_tlv_calib_ctrl { + __le32 flow_trigger; + __le32 event_trigger; +} __packed; + +enum iwl_fw_phy_cfg { + FW_PHY_CFG_RADIO_TYPE_POS = 0, + FW_PHY_CFG_RADIO_TYPE = 0x3 << FW_PHY_CFG_RADIO_TYPE_POS, + FW_PHY_CFG_RADIO_STEP_POS = 2, + FW_PHY_CFG_RADIO_STEP = 0x3 << FW_PHY_CFG_RADIO_STEP_POS, + FW_PHY_CFG_RADIO_DASH_POS = 4, + FW_PHY_CFG_RADIO_DASH = 0x3 << FW_PHY_CFG_RADIO_DASH_POS, + FW_PHY_CFG_TX_CHAIN_POS = 16, + FW_PHY_CFG_TX_CHAIN = 0xf << FW_PHY_CFG_TX_CHAIN_POS, + FW_PHY_CFG_RX_CHAIN_POS = 20, + FW_PHY_CFG_RX_CHAIN = 0xf << FW_PHY_CFG_RX_CHAIN_POS, +}; + +#define IWL_UCODE_MAX_CS 1 + +/** + * struct iwl_fw_cipher_scheme - a cipher scheme supported by FW. + * @cipher: a cipher suite selector + * @flags: cipher scheme flags (currently reserved for a future use) + * @hdr_len: a size of MPDU security header + * @pn_len: a size of PN + * @pn_off: an offset of pn from the beginning of the security header + * @key_idx_off: an offset of key index byte in the security header + * @key_idx_mask: a bit mask of key_idx bits + * @key_idx_shift: bit shift needed to get key_idx + * @mic_len: mic length in bytes + * @hw_cipher: a HW cipher index used in host commands + */ +struct iwl_fw_cipher_scheme { + __le32 cipher; + u8 flags; + u8 hdr_len; + u8 pn_len; + u8 pn_off; + u8 key_idx_off; + u8 key_idx_mask; + u8 key_idx_shift; + u8 mic_len; + u8 hw_cipher; +} __packed; + +enum iwl_fw_dbg_reg_operator { + CSR_ASSIGN, + CSR_SETBIT, + CSR_CLEARBIT, + + PRPH_ASSIGN, + PRPH_SETBIT, + PRPH_CLEARBIT, +}; + +/** + * struct iwl_fw_dbg_reg_op - an operation on a register + * + * @op: %enum iwl_fw_dbg_reg_operator + * @addr: offset of the register + * @val: value + */ +struct iwl_fw_dbg_reg_op { + u8 op; + u8 reserved[3]; + __le32 addr; + __le32 val; +} __packed; + +/** + * enum iwl_fw_dbg_monitor_mode - available monitor recording modes + * + * @SMEM_MODE: monitor stores the data in SMEM + * @EXTERNAL_MODE: monitor stores the data in allocated DRAM + * @MARBH_MODE: monitor stores the data in MARBH buffer + */ +enum iwl_fw_dbg_monitor_mode { + SMEM_MODE = 0, + EXTERNAL_MODE = 1, + MARBH_MODE = 2, +}; + +/** + * struct iwl_fw_dbg_dest_tlv - configures the destination of the debug data + * + * @version: version of the TLV - currently 0 + * @monitor_mode: %enum iwl_fw_dbg_monitor_mode + * @base_reg: addr of the base addr register (PRPH) + * @end_reg: addr of the end addr register (PRPH) + * @write_ptr_reg: the addr of the reg of the write pointer + * @wrap_count: the addr of the reg of the wrap_count + * @base_shift: shift right of the base addr reg + * @end_shift: shift right of the end addr reg + * @reg_ops: array of registers operations + * + * This parses IWL_UCODE_TLV_FW_DBG_DEST + */ +struct iwl_fw_dbg_dest_tlv { + u8 version; + u8 monitor_mode; + u8 reserved[2]; + __le32 base_reg; + __le32 end_reg; + __le32 write_ptr_reg; + __le32 wrap_count; + u8 base_shift; + u8 end_shift; + struct iwl_fw_dbg_reg_op reg_ops[0]; +} __packed; + +struct iwl_fw_dbg_conf_hcmd { + u8 id; + u8 reserved; + __le16 len; + u8 data[0]; +} __packed; + +/** + * struct iwl_fw_dbg_trigger - a TLV that describes a debug configuration + * + * @enabled: is this trigger enabled + * @reserved: + * @len: length, in bytes, of the %trigger field + * @trigger: pointer to a trigger struct + */ +struct iwl_fw_dbg_trigger { + u8 enabled; + u8 reserved; + u8 len; + u8 trigger[0]; +} __packed; + +/** + * enum iwl_fw_dbg_conf - configurations available + * + * @FW_DBG_CUSTOM: take this configuration from alive + * Note that the trigger is NO-OP for this configuration + */ +enum iwl_fw_dbg_conf { + FW_DBG_CUSTOM = 0, + + /* must be last */ + FW_DBG_MAX, + FW_DBG_INVALID = 0xff, +}; + +/** + * struct iwl_fw_dbg_conf_tlv - a TLV that describes a debug configuration + * + * @id: %enum iwl_fw_dbg_conf + * @usniffer: should the uSniffer image be used + * @num_of_hcmds: how many HCMDs to send are present here + * @hcmd: a variable length host command to be sent to apply the configuration. + * If there is more than one HCMD to send, they will appear one after the + * other and be sent in the order that they appear in. + * This parses IWL_UCODE_TLV_FW_DBG_CONF + */ +struct iwl_fw_dbg_conf_tlv { + u8 id; + u8 usniffer; + u8 reserved; + u8 num_of_hcmds; + struct iwl_fw_dbg_conf_hcmd hcmd; + + /* struct iwl_fw_dbg_trigger sits after all variable length hcmds */ +} __packed; + #endif /* __iwl_fw_file_h__ */ |
