diff options
Diffstat (limited to 'drivers/net/wireless/ath/ath5k/phy.c')
| -rw-r--r-- | drivers/net/wireless/ath/ath5k/phy.c | 82 |
1 files changed, 62 insertions, 20 deletions
diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c index 01cb72d..ca4241d 100644 --- a/drivers/net/wireless/ath/ath5k/phy.c +++ b/drivers/net/wireless/ath/ath5k/phy.c @@ -338,9 +338,6 @@ static void ath5k_hw_wait_for_synth(struct ath5k_hw *ah, * And this is the MadWiFi bug entry related to the above * http://madwifi-project.org/ticket/1659 * with various measurements and diagrams - * - * TODO: Deal with power drops due to probes by setting an appropriate - * tx power on the probe packets ! Make this part of the calibration process. */ /* Initialize ah_gain during attach */ @@ -372,10 +369,9 @@ int ath5k_hw_rfgain_opt_init(struct ath5k_hw *ah) * tx power and a Peak to Average Power Detector (PAPD) will try * to measure the gain. * - * XXX: How about forcing a tx packet (bypassing PCU arbitrator etc) + * TODO: Force a tx packet (bypassing PCU arbitrator etc) * just after we enable the probe so that we don't mess with - * standard traffic ? Maybe it's time to use sw interrupts and - * a probe tasklet !!! + * standard traffic. */ static void ath5k_hw_request_rfgain_probe(struct ath5k_hw *ah) { @@ -575,9 +571,7 @@ done: /* Main callback for thermal RF gain calibration engine * Check for a new gain reading and schedule an adjustment * if needed. - * - * TODO: Use sw interrupt to schedule reset if gain_F needs - * adjustment */ + */ enum ath5k_rfgain ath5k_hw_gainf_calibrate(struct ath5k_hw *ah) { u32 data, type; @@ -1390,6 +1384,8 @@ void ath5k_hw_update_noise_floor(struct ath5k_hw *ah) return; } + ah->ah_cal_mask |= AR5K_CALIBRATION_NF; + ee_mode = ath5k_eeprom_mode_from_channel(ah->ah_current_channel); /* completed NF calibration, test threshold */ @@ -1434,6 +1430,8 @@ void ath5k_hw_update_noise_floor(struct ath5k_hw *ah) ah->ah_noise_floor = nf; + ah->ah_cal_mask &= ~AR5K_CALIBRATION_NF; + ATH5K_DBG(ah, ATH5K_DEBUG_CALIBRATE, "noise floor calibrated: %d\n", nf); } @@ -1547,12 +1545,19 @@ ath5k_hw_rf511x_iq_calibrate(struct ath5k_hw *ah) s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd; int i; - if (!ah->ah_calibration || - ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN) - return 0; + /* Skip if I/Q calibration is not needed or if it's still running */ + if (!ah->ah_iq_cal_needed) + return -EINVAL; + else if (ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN) { + ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_CALIBRATE, + "I/Q calibration still running"); + return -EBUSY; + } /* Calibration has finished, get the results and re-run */ - /* work around empty results which can apparently happen on 5212 */ + + /* Work around for empty results which can apparently happen on 5212: + * Read registers up to 10 times until we get both i_pr and q_pwr */ for (i = 0; i <= 10; i++) { iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR); i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I); @@ -1570,9 +1575,13 @@ ath5k_hw_rf511x_iq_calibrate(struct ath5k_hw *ah) else q_coffd = q_pwr >> 7; - /* protect against divide by 0 and loss of sign bits */ + /* In case i_coffd became zero, cancel calibration + * not only it's too small, it'll also result a divide + * by zero later on. */ if (i_coffd == 0 || q_coffd < 2) - return 0; + return -ECANCELED; + + /* Protect against loss of sign bits */ i_coff = (-iq_corr) / i_coffd; i_coff = clamp(i_coff, -32, 31); /* signed 6 bit */ @@ -1613,10 +1622,43 @@ int ath5k_hw_phy_calibrate(struct ath5k_hw *ah, return ath5k_hw_rf5110_calibrate(ah, channel); ret = ath5k_hw_rf511x_iq_calibrate(ah); + if (ret) { + ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_CALIBRATE, + "No I/Q correction performed (%uMHz)\n", + channel->center_freq); + + /* Happens all the time if there is not much + * traffic, consider it normal behaviour. */ + ret = 0; + } + + /* On full calibration do an AGC calibration and + * request a PAPD probe for gainf calibration if + * needed */ + if (ah->ah_cal_mask & AR5K_CALIBRATION_FULL) { + + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, + AR5K_PHY_AGCCTL_CAL); + + ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, + AR5K_PHY_AGCCTL_CAL | AR5K_PHY_AGCCTL_NF, + 0, false); + if (ret) { + ATH5K_ERR(ah, + "gain calibration timeout (%uMHz)\n", + channel->center_freq); + } + + if ((ah->ah_radio == AR5K_RF5111 || + ah->ah_radio == AR5K_RF5112) + && (channel->hw_value != AR5K_MODE_11B)) + ath5k_hw_request_rfgain_probe(ah); + } - if ((ah->ah_radio == AR5K_RF5111 || ah->ah_radio == AR5K_RF5112) && - (channel->hw_value != AR5K_MODE_11B)) - ath5k_hw_request_rfgain_probe(ah); + /* Update noise floor + * XXX: Only do this after AGC calibration */ + if (!(ah->ah_cal_mask & AR5K_CALIBRATION_NF)) + ath5k_hw_update_noise_floor(ah); return ret; } @@ -3433,9 +3475,9 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel, /* At the same time start I/Q calibration for QAM constellation * -no need for CCK- */ - ah->ah_calibration = false; + ah->ah_iq_cal_needed = false; if (!(mode == AR5K_MODE_11B)) { - ah->ah_calibration = true; + ah->ah_iq_cal_needed = true; AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15); AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, |
