diff options
Diffstat (limited to 'drivers/net/tulip/Kconfig')
| -rw-r--r-- | drivers/net/tulip/Kconfig | 166 |
1 files changed, 166 insertions, 0 deletions
diff --git a/drivers/net/tulip/Kconfig b/drivers/net/tulip/Kconfig new file mode 100644 index 0000000..e2cdaf8 --- /dev/null +++ b/drivers/net/tulip/Kconfig @@ -0,0 +1,166 @@ +# +# Tulip family network device configuration +# + +menu "Tulip family network device support" + depends on NET_ETHERNET && (PCI || EISA || CARDBUS) + +config NET_TULIP + bool "\"Tulip\" family network device support" + help + This selects the "Tulip" family of EISA/PCI network cards. + +config DE2104X + tristate "Early DECchip Tulip (dc2104x) PCI support (EXPERIMENTAL)" + depends on NET_TULIP && PCI && EXPERIMENTAL + select CRC32 + ---help--- + This driver is developed for the SMC EtherPower series Ethernet + cards and also works with cards based on the DECchip + 21040 (Tulip series) chips. Some LinkSys PCI cards are + of this type. (If your card is NOT SMC EtherPower 10/100 PCI + (smc9332dst), you can also try the driver for "Generic DECchip" + cards, below. However, most people with a network card of this type + will say Y here.) Do read the Ethernet-HOWTO, available from + <http://www.tldp.org/docs.html#howto>. + + To compile this driver as a module, choose M here and read + <file:Documentation/networking/net-modules.txt>. The module will + be called de2104x. + +config TULIP + tristate "DECchip Tulip (dc2114x) PCI support" + depends on NET_TULIP && PCI + select CRC32 + ---help--- + This driver is developed for the SMC EtherPower series Ethernet + cards and also works with cards based on the DECchip + 21140 (Tulip series) chips. Some LinkSys PCI cards are + of this type. (If your card is NOT SMC EtherPower 10/100 PCI + (smc9332dst), you can also try the driver for "Generic DECchip" + cards, above. However, most people with a network card of this type + will say Y here.) Do read the Ethernet-HOWTO, available from + <http://www.tldp.org/docs.html#howto>. + + To compile this driver as a module, choose M here and read + <file:Documentation/networking/net-modules.txt>. The module will + be called tulip. + +config TULIP_MWI + bool "New bus configuration (EXPERIMENTAL)" + depends on TULIP && EXPERIMENTAL + help + This configures your Tulip card specifically for the card and + system cache line size type you are using. + + This is experimental code, not yet tested on many boards. + + If unsure, say N. + +config TULIP_MMIO + bool "Use PCI shared mem for NIC registers" + depends on TULIP + help + Use PCI shared memory for the NIC registers, rather than going through + the Tulip's PIO (programmed I/O ports). Faster, but could produce + obscure bugs if your mainboard has memory controller timing issues. + If in doubt, say N. + +config TULIP_NAPI + bool "Use NAPI RX polling " + depends on TULIP + help + NAPI is a new driver API designed to reduce CPU and interrupt load + when the driver is receiving lots of packets from the card. It is + still somewhat experimental and thus not yet enabled by default. + + If your estimated Rx load is 10kpps or more, or if the card will be + deployed on potentially unfriendly networks (e.g. in a firewall), + then say Y here. + + See <file:Documentation/networking/NAPI_HOWTO.txt> for more + information. + + If in doubt, say N. + +config TULIP_NAPI_HW_MITIGATION + bool "Use Interrupt Mitigation " + depends on TULIP_NAPI + ---help--- + Use HW to reduce RX interrupts. Not strict necessary since NAPI reduces + RX interrupts but itself. Although this reduces RX interrupts even at + low levels traffic at the cost of a small latency. + + If in doubt, say Y. + +config DE4X5 + tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA" + depends on NET_TULIP && (PCI || EISA) + select CRC32 + ---help--- + This is support for the DIGITAL series of PCI/EISA Ethernet cards. + These include the DE425, DE434, DE435, DE450 and DE500 models. If + you have a network card of this type, say Y and read the + Ethernet-HOWTO, available from + <http://www.tldp.org/docs.html#howto>. More specific + information is contained in + <file:Documentation/networking/de4x5.txt>. + + To compile this driver as a module, choose M here and read + <file:Documentation/networking/net-modules.txt>. The module will + be called de4x5. + +config WINBOND_840 + tristate "Winbond W89c840 Ethernet support" + depends on NET_TULIP && PCI + select CRC32 + select MII + help + This driver is for the Winbond W89c840 chip. It also works with + the TX9882 chip on the Compex RL100-ATX board. + More specific information and updates are available from + <http://www.scyld.com/network/drivers.html>. + +config DM9102 + tristate "Davicom DM910x/DM980x support" + depends on NET_TULIP && PCI + select CRC32 + ---help--- + This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from + Davicom (<http://www.davicom.com.tw/>). If you have such a network + (Ethernet) card, say Y. Some information is contained in the file + <file:Documentation/networking/dmfe.txt>. + + To compile this driver as a module, choose M here and read + <file:Documentation/networking/net-modules.txt>. The module will + be called dmfe. + +config PCMCIA_XIRCOM + tristate "Xircom CardBus support (new driver)" + depends on NET_TULIP && CARDBUS + ---help--- + This driver is for the Digital "Tulip" Ethernet CardBus adapters. + It should work with most DEC 21*4*-based chips/ethercards, as well + as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and + ASIX. + + To compile this driver as a module, choose M here and read + <file:Documentation/networking/net-modules.txt>. The module will + be called xircom_cb. If unsure, say N. + +config PCMCIA_XIRTULIP + tristate "Xircom Tulip-like CardBus support (old driver)" + depends on NET_TULIP && CARDBUS && BROKEN_ON_SMP + select CRC32 + ---help--- + This driver is for the Digital "Tulip" Ethernet CardBus adapters. + It should work with most DEC 21*4*-based chips/ethercards, as well + as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and + ASIX. + + To compile this driver as a module, choose M here and read + <file:Documentation/networking/net-modules.txt>. The module will + be called xircom_tulip_cb. If unsure, say N. + +endmenu + |
