diff options
Diffstat (limited to 'drivers/net/phy/broadcom.c')
| -rw-r--r-- | drivers/net/phy/broadcom.c | 201 |
1 files changed, 199 insertions, 2 deletions
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c index 60c5cfe..4b4dc98 100644 --- a/drivers/net/phy/broadcom.c +++ b/drivers/net/phy/broadcom.c @@ -24,6 +24,12 @@ #define MII_BCM54XX_ESR 0x11 /* BCM54xx extended status register */ #define MII_BCM54XX_ESR_IS 0x1000 /* Interrupt status */ +#define MII_BCM54XX_EXP_DATA 0x15 /* Expansion register data */ +#define MII_BCM54XX_EXP_SEL 0x17 /* Expansion register select */ +#define MII_BCM54XX_EXP_SEL_SSD 0x0e00 /* Secondary SerDes select */ +#define MII_BCM54XX_EXP_SEL_ER 0x0f00 /* Expansion register select */ + +#define MII_BCM54XX_AUX_CTL 0x18 /* Auxiliary control register */ #define MII_BCM54XX_ISR 0x1a /* BCM54xx interrupt status register */ #define MII_BCM54XX_IMR 0x1b /* BCM54xx interrupt mask register */ #define MII_BCM54XX_INT_CRCERR 0x0001 /* CRC error */ @@ -42,10 +48,120 @@ #define MII_BCM54XX_INT_MDIX 0x2000 /* MDIX status change */ #define MII_BCM54XX_INT_PSERR 0x4000 /* Pair swap error */ +#define MII_BCM54XX_SHD 0x1c /* 0x1c shadow registers */ +#define MII_BCM54XX_SHD_WRITE 0x8000 +#define MII_BCM54XX_SHD_VAL(x) ((x & 0x1f) << 10) +#define MII_BCM54XX_SHD_DATA(x) ((x & 0x3ff) << 0) + +/* + * Broadcom LED source encodings. These are used in BCM5461, BCM5481, + * BCM5482, and possibly some others. + */ +#define BCM_LED_SRC_LINKSPD1 0x0 +#define BCM_LED_SRC_LINKSPD2 0x1 +#define BCM_LED_SRC_XMITLED 0x2 +#define BCM_LED_SRC_ACTIVITYLED 0x3 +#define BCM_LED_SRC_FDXLED 0x4 +#define BCM_LED_SRC_SLAVE 0x5 +#define BCM_LED_SRC_INTR 0x6 +#define BCM_LED_SRC_QUALITY 0x7 +#define BCM_LED_SRC_RCVLED 0x8 +#define BCM_LED_SRC_MULTICOLOR1 0xa +#define BCM_LED_SRC_OPENSHORT 0xb +#define BCM_LED_SRC_OFF 0xe /* Tied high */ +#define BCM_LED_SRC_ON 0xf /* Tied low */ + +/* + * BCM5482: Shadow registers + * Shadow values go into bits [14:10] of register 0x1c to select a shadow + * register to access. + */ +#define BCM5482_SHD_LEDS1 0x0d /* 01101: LED Selector 1 */ + /* LED3 / ~LINKSPD[2] selector */ +#define BCM5482_SHD_LEDS1_LED3(src) ((src & 0xf) << 4) + /* LED1 / ~LINKSPD[1] selector */ +#define BCM5482_SHD_LEDS1_LED1(src) ((src & 0xf) << 0) +#define BCM5482_SHD_SSD 0x14 /* 10100: Secondary SerDes control */ +#define BCM5482_SHD_SSD_LEDM 0x0008 /* SSD LED Mode enable */ +#define BCM5482_SHD_SSD_EN 0x0001 /* SSD enable */ +#define BCM5482_SHD_MODE 0x1f /* 11111: Mode Control Register */ +#define BCM5482_SHD_MODE_1000BX 0x0001 /* Enable 1000BASE-X registers */ + +/* + * BCM5482: Secondary SerDes registers + */ +#define BCM5482_SSD_1000BX_CTL 0x00 /* 1000BASE-X Control */ +#define BCM5482_SSD_1000BX_CTL_PWRDOWN 0x0800 /* Power-down SSD */ +#define BCM5482_SSD_SGMII_SLAVE 0x15 /* SGMII Slave Register */ +#define BCM5482_SSD_SGMII_SLAVE_EN 0x0002 /* Slave mode enable */ +#define BCM5482_SSD_SGMII_SLAVE_AD 0x0001 /* Slave auto-detection */ + +/* + * Device flags for PHYs that can be configured for different operating + * modes. + */ +#define PHY_BCM_FLAGS_VALID 0x80000000 +#define PHY_BCM_FLAGS_INTF_XAUI 0x00000020 +#define PHY_BCM_FLAGS_INTF_SGMII 0x00000010 +#define PHY_BCM_FLAGS_MODE_1000BX 0x00000002 +#define PHY_BCM_FLAGS_MODE_COPPER 0x00000001 + MODULE_DESCRIPTION("Broadcom PHY driver"); MODULE_AUTHOR("Maciej W. Rozycki"); MODULE_LICENSE("GPL"); +/* + * Indirect register access functions for the 1000BASE-T/100BASE-TX/10BASE-T + * 0x1c shadow registers. + */ +static int bcm54xx_shadow_read(struct phy_device *phydev, u16 shadow) +{ + phy_write(phydev, MII_BCM54XX_SHD, MII_BCM54XX_SHD_VAL(shadow)); + return MII_BCM54XX_SHD_DATA(phy_read(phydev, MII_BCM54XX_SHD)); +} + +static int bcm54xx_shadow_write(struct phy_device *phydev, u16 shadow, u16 val) +{ + return phy_write(phydev, MII_BCM54XX_SHD, + MII_BCM54XX_SHD_WRITE | + MII_BCM54XX_SHD_VAL(shadow) | + MII_BCM54XX_SHD_DATA(val)); +} + +/* + * Indirect register access functions for the Expansion Registers + * and Secondary SerDes registers (when sec_serdes=1). + */ +static int bcm54xx_exp_read(struct phy_device *phydev, + int sec_serdes, u8 regnum) +{ + int val; + + phy_write(phydev, MII_BCM54XX_EXP_SEL, + (sec_serdes ? MII_BCM54XX_EXP_SEL_SSD : + MII_BCM54XX_EXP_SEL_ER) | + regnum); + val = phy_read(phydev, MII_BCM54XX_EXP_DATA); + phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum); + + return val; +} + +static int bcm54xx_exp_write(struct phy_device *phydev, + int sec_serdes, u8 regnum, u16 val) +{ + int ret; + + phy_write(phydev, MII_BCM54XX_EXP_SEL, + (sec_serdes ? MII_BCM54XX_EXP_SEL_SSD : + MII_BCM54XX_EXP_SEL_ER) | + regnum); + ret = phy_write(phydev, MII_BCM54XX_EXP_DATA, val); + phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum); + + return ret; +} + static int bcm54xx_config_init(struct phy_device *phydev) { int reg, err; @@ -70,6 +186,87 @@ static int bcm54xx_config_init(struct phy_device *phydev) return 0; } +static int bcm5482_config_init(struct phy_device *phydev) +{ + int err, reg; + + err = bcm54xx_config_init(phydev); + + if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX) { + /* + * Enable secondary SerDes and its use as an LED source + */ + reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_SSD); + bcm54xx_shadow_write(phydev, BCM5482_SHD_SSD, + reg | + BCM5482_SHD_SSD_LEDM | + BCM5482_SHD_SSD_EN); + + /* + * Enable SGMII slave mode and auto-detection + */ + reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_SGMII_SLAVE); + bcm54xx_exp_write(phydev, 1, BCM5482_SSD_SGMII_SLAVE, + reg | + BCM5482_SSD_SGMII_SLAVE_EN | + BCM5482_SSD_SGMII_SLAVE_AD); + + /* + * Disable secondary SerDes powerdown + */ + reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_1000BX_CTL); + bcm54xx_exp_write(phydev, 1, BCM5482_SSD_1000BX_CTL, + reg & ~BCM5482_SSD_1000BX_CTL_PWRDOWN); + + /* + * Select 1000BASE-X register set (primary SerDes) + */ + reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_MODE); + bcm54xx_shadow_write(phydev, BCM5482_SHD_MODE, + reg | BCM5482_SHD_MODE_1000BX); + + /* + * LED1=ACTIVITYLED, LED3=LINKSPD[2] + * (Use LED1 as secondary SerDes ACTIVITY LED) + */ + bcm54xx_shadow_write(phydev, BCM5482_SHD_LEDS1, + BCM5482_SHD_LEDS1_LED1(BCM_LED_SRC_ACTIVITYLED) | + BCM5482_SHD_LEDS1_LED3(BCM_LED_SRC_LINKSPD2)); + + /* + * Auto-negotiation doesn't seem to work quite right + * in this mode, so we disable it and force it to the + * right speed/duplex setting. Only 'link status' + * is important. + */ + phydev->autoneg = AUTONEG_DISABLE; + phydev->speed = SPEED_1000; + phydev->duplex = DUPLEX_FULL; + } + + return err; +} + +static int bcm5482_read_status(struct phy_device *phydev) +{ + int err; + + err = genphy_read_status(phydev); + + if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX) { + /* + * Only link status matters for 1000Base-X mode, so force + * 1000 Mbit/s full-duplex status + */ + if (phydev->link) { + phydev->speed = SPEED_1000; + phydev->duplex = DUPLEX_FULL; + } + } + + return err; +} + static int bcm54xx_ack_interrupt(struct phy_device *phydev) { int reg; @@ -210,9 +407,9 @@ static struct phy_driver bcm5482_driver = { .name = "Broadcom BCM5482", .features = PHY_GBIT_FEATURES, .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, - .config_init = bcm54xx_config_init, + .config_init = bcm5482_config_init, .config_aneg = genphy_config_aneg, - .read_status = genphy_read_status, + .read_status = bcm5482_read_status, .ack_interrupt = bcm54xx_ack_interrupt, .config_intr = bcm54xx_config_intr, .driver = { .owner = THIS_MODULE }, |
