diff options
Diffstat (limited to 'drivers/net/phy/bcm7xxx.c')
| -rw-r--r-- | drivers/net/phy/bcm7xxx.c | 151 |
1 files changed, 93 insertions, 58 deletions
diff --git a/drivers/net/phy/bcm7xxx.c b/drivers/net/phy/bcm7xxx.c index 1d211d3..974ec45 100644 --- a/drivers/net/phy/bcm7xxx.c +++ b/drivers/net/phy/bcm7xxx.c @@ -39,45 +39,15 @@ #define AFE_RXCONFIG_0 MISC_ADDR(0x38, 0) #define AFE_RXCONFIG_1 MISC_ADDR(0x38, 1) +#define AFE_RXCONFIG_2 MISC_ADDR(0x38, 2) #define AFE_RX_LP_COUNTER MISC_ADDR(0x38, 3) #define AFE_TX_CONFIG MISC_ADDR(0x39, 0) +#define AFE_VDCA_ICTRL_0 MISC_ADDR(0x39, 1) +#define AFE_VDAC_OTHERS_0 MISC_ADDR(0x39, 3) #define AFE_HPF_TRIM_OTHERS MISC_ADDR(0x3a, 0) #define CORE_EXPB0 0xb0 -static int bcm7445_config_init(struct phy_device *phydev) -{ - int ret; - const struct bcm7445_regs { - int reg; - u16 value; - } bcm7445_regs_cfg[] = { - /* increases ADC latency by 24ns */ - { MII_BCM54XX_EXP_SEL, 0x0038 }, - { MII_BCM54XX_EXP_DATA, 0xAB95 }, - /* increases internal 1V LDO voltage by 5% */ - { MII_BCM54XX_EXP_SEL, 0x2038 }, - { MII_BCM54XX_EXP_DATA, 0xBB22 }, - /* reduce RX low pass filter corner frequency */ - { MII_BCM54XX_EXP_SEL, 0x6038 }, - { MII_BCM54XX_EXP_DATA, 0xFFC5 }, - /* reduce RX high pass filter corner frequency */ - { MII_BCM54XX_EXP_SEL, 0x003a }, - { MII_BCM54XX_EXP_DATA, 0x2002 }, - }; - unsigned int i; - - for (i = 0; i < ARRAY_SIZE(bcm7445_regs_cfg); i++) { - ret = phy_write(phydev, - bcm7445_regs_cfg[i].reg, - bcm7445_regs_cfg[i].value); - if (ret) - return ret; - } - - return 0; -} - static void phy_write_exp(struct phy_device *phydev, u16 reg, u16 value) { @@ -102,7 +72,16 @@ static void phy_write_misc(struct phy_device *phydev, phy_write(phydev, MII_BCM54XX_EXP_DATA, value); } -static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev) +static void r_rc_cal_reset(struct phy_device *phydev) +{ + /* Reset R_CAL/RC_CAL Engine */ + phy_write_exp(phydev, 0x00b0, 0x0010); + + /* Disable Reset R_AL/RC_CAL Engine */ + phy_write_exp(phydev, 0x00b0, 0x0000); +} + +static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev) { /* Increase VCO range to prevent unlocking problem of PLL at low * temp @@ -123,11 +102,7 @@ static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev) /* Switch to CORE_BASE1E */ phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd); - /* Reset R_CAL/RC_CAL Engine */ - phy_write_exp(phydev, CORE_EXPB0, 0x0010); - - /* Disable Reset R_CAL/RC_CAL Engine */ - phy_write_exp(phydev, CORE_EXPB0, 0x0000); + r_rc_cal_reset(phydev); /* write AFE_RXCONFIG_0 */ phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19); @@ -147,6 +122,71 @@ static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev) return 0; } +static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev) +{ + /* AFE_RXCONFIG_0 */ + phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15); + + /* AFE_RXCONFIG_1 */ + phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f); + + /* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */ + phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003); + + /* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */ + phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0); + + /* AFE_TX_CONFIG, set 1000BT Cfeed=110 for all ports */ + phy_write_misc(phydev, AFE_TX_CONFIG, 0x0061); + + /* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */ + phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da); + + /* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */ + phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020); + + /* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal + * offset for HT=0 code + */ + phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3); + + /* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */ + phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010); + + /* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */ + phy_write_misc(phydev, DSP_TAP10, 0x011b); + + /* Reset R_CAL/RC_CAL engine */ + r_rc_cal_reset(phydev); + + return 0; +} + +static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev) +{ + /* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */ + phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f); + + /* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */ + phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da); + + /* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal + * offset for HT=0 code + */ + phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3); + + /* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */ + phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010); + + /* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */ + phy_write_misc(phydev, DSP_TAP10, 0x011b); + + /* Reset R_CAL/RC_CAL engine */ + r_rc_cal_reset(phydev); + + return 0; +} + static int bcm7xxx_apd_enable(struct phy_device *phydev) { int val; @@ -200,15 +240,23 @@ static int bcm7xxx_28nm_config_init(struct phy_device *phydev) u8 patch = PHY_BRCM_7XXX_PATCH(phydev->dev_flags); int ret = 0; - dev_info(&phydev->dev, "PHY revision: 0x%02x, patch: %d\n", rev, patch); + pr_info_once("%s: %s PHY revision: 0x%02x, patch: %d\n", + dev_name(&phydev->dev), phydev->drv->name, rev, patch); switch (rev) { - case 0xa0: case 0xb0: - ret = bcm7445_config_init(phydev); + ret = bcm7xxx_28nm_b0_afe_config_init(phydev); + break; + case 0xd0: + ret = bcm7xxx_28nm_d0_afe_config_init(phydev); + break; + case 0xe0: + case 0xf0: + /* Rev G0 introduces a roll over */ + case 0x10: + ret = bcm7xxx_28nm_e0_plus_afe_config_init(phydev); break; default: - ret = bcm7xxx_28nm_afe_config_init(phydev); break; } @@ -336,7 +384,7 @@ static int bcm7xxx_dummy_config_init(struct phy_device *phydev) .features = PHY_GBIT_FEATURES | \ SUPPORTED_Pause | SUPPORTED_Asym_Pause, \ .flags = PHY_IS_INTERNAL, \ - .config_init = bcm7xxx_28nm_afe_config_init, \ + .config_init = bcm7xxx_28nm_config_init, \ .config_aneg = genphy_config_aneg, \ .read_status = genphy_read_status, \ .resume = bcm7xxx_28nm_resume, \ @@ -416,20 +464,7 @@ static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = { { } }; -static int __init bcm7xxx_phy_init(void) -{ - return phy_drivers_register(bcm7xxx_driver, - ARRAY_SIZE(bcm7xxx_driver)); -} - -static void __exit bcm7xxx_phy_exit(void) -{ - phy_drivers_unregister(bcm7xxx_driver, - ARRAY_SIZE(bcm7xxx_driver)); -} - -module_init(bcm7xxx_phy_init); -module_exit(bcm7xxx_phy_exit); +module_phy_driver(bcm7xxx_driver); MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl); |
