diff options
Diffstat (limited to 'drivers/net/mipsnet.h')
-rw-r--r-- | drivers/net/mipsnet.h | 112 |
1 files changed, 0 insertions, 112 deletions
diff --git a/drivers/net/mipsnet.h b/drivers/net/mipsnet.h deleted file mode 100644 index 0132c67..0000000 --- a/drivers/net/mipsnet.h +++ /dev/null @@ -1,112 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - */ -#ifndef __MIPSNET_H -#define __MIPSNET_H - -/* - * Id of this Net device, as seen by the core. - */ -#define MIPS_NET_DEV_ID ((uint64_t) \ - ((uint64_t) 'M' << 0)| \ - ((uint64_t) 'I' << 8)| \ - ((uint64_t) 'P' << 16)| \ - ((uint64_t) 'S' << 24)| \ - ((uint64_t) 'N' << 32)| \ - ((uint64_t) 'E' << 40)| \ - ((uint64_t) 'T' << 48)| \ - ((uint64_t) '0' << 56)) - -/* - * Net status/control block as seen by sw in the core. - * (Why not use bit fields? can't be bothered with cross-platform struct - * packing.) - */ -struct net_control_block { - /* - * dev info for probing - * reads as MIPSNET%d where %d is some form of version - */ - uint64_t devId; /* 0x00 */ - - /* - * read only busy flag. - * Set and cleared by the Net Device to indicate that an rx or a tx - * is in progress. - */ - uint32_t busy; /* 0x08 */ - - /* - * Set by the Net Device. - * The device will set it once data has been received. - * The value is the number of bytes that should be read from - * rxDataBuffer. The value will decrease till 0 until all the data - * from rxDataBuffer has been read. - */ - uint32_t rxDataCount; /* 0x0c */ -#define MIPSNET_MAX_RXTX_DATACOUNT (1<<16) - - /* - * Settable from the MIPS core, cleared by the Net Device. The core - * should set the number of bytes it wants to send, then it should - * write those bytes of data to txDataBuffer. The device will clear - * txDataCount has been processed (not necessarily sent). - */ - uint32_t txDataCount; /* 0x10 */ - - /* - * Interrupt control - * - * Used to clear the interrupted generated by this dev. - * Write a 1 to clear the interrupt. (except bit31). - * - * Bit0 is set if it was a tx-done interrupt. - * Bit1 is set when new rx-data is available. - * Until this bit is cleared there will be no other RXs. - * - * Bit31 is used for testing, it clears after a read. - * Writing 1 to this bit will cause an interrupt to be generated. - * To clear the test interrupt, write 0 to this register. - */ - uint32_t interruptControl; /*0x14 */ -#define MIPSNET_INTCTL_TXDONE ((uint32_t)(1 << 0)) -#define MIPSNET_INTCTL_RXDONE ((uint32_t)(1 << 1)) -#define MIPSNET_INTCTL_TESTBIT ((uint32_t)(1 << 31)) -#define MIPSNET_INTCTL_ALLSOURCES (MIPSNET_INTCTL_TXDONE | \ - MIPSNET_INTCTL_RXDONE | \ - MIPSNET_INTCTL_TESTBIT) - - /* - * Readonly core-specific interrupt info for the device to signal the - * core. The meaning of the contents of this field might change. - * - * TODO: the whole memIntf interrupt scheme is messy: the device should - * have no control what so ever of what VPE/register set is being - * used. The MemIntf should only expose interrupt lines, and - * something in the config should be responsible for the - * line<->core/vpe bindings. - */ - uint32_t interruptInfo; /* 0x18 */ - - /* - * This is where the received data is read out. - * There is more data to read until rxDataReady is 0. - * Only 1 byte at this regs offset is used. - */ - uint32_t rxDataBuffer; /* 0x1c */ - - /* - * This is where the data to transmit is written. Data should be - * written for the amount specified in the txDataCount register. Only - * 1 byte at this regs offset is used. - */ - uint32_t txDataBuffer; /* 0x20 */ -}; - -#define MIPSNET_IO_EXTENT 0x40 /* being generous */ - -#define field_offset(field) (offsetof(struct net_control_block, field)) - -#endif /* __MIPSNET_H */ |