diff options
Diffstat (limited to 'drivers/net/ixgbe/ixgbe_common.c')
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_common.c | 1060 |
1 files changed, 740 insertions, 320 deletions
diff --git a/drivers/net/ixgbe/ixgbe_common.c b/drivers/net/ixgbe/ixgbe_common.c index 7fd6aeb..f67c684 100644 --- a/drivers/net/ixgbe/ixgbe_common.c +++ b/drivers/net/ixgbe/ixgbe_common.c @@ -1,7 +1,7 @@ /******************************************************************************* Intel 10 Gigabit PCI Express Linux driver - Copyright(c) 1999 - 2007 Intel Corporation. + Copyright(c) 1999 - 2008 Intel Corporation. This program is free software; you can redistribute it and/or modify it under the terms and conditions of the GNU General Public License, @@ -20,7 +20,6 @@ the file called "COPYING". Contact Information: - Linux NICS <linux.nics@intel.com> e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 @@ -33,20 +32,28 @@ #include "ixgbe_common.h" #include "ixgbe_phy.h" -static s32 ixgbe_clear_hw_cntrs(struct ixgbe_hw *hw); - static s32 ixgbe_poll_eeprom_eerd_done(struct ixgbe_hw *hw); +static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw); static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw); static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw); +static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw); +static void ixgbe_standby_eeprom(struct ixgbe_hw *hw); +static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, + u16 count); +static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count); +static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); +static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); +static void ixgbe_release_eeprom(struct ixgbe_hw *hw); static u16 ixgbe_calc_eeprom_checksum(struct ixgbe_hw *hw); -static s32 ixgbe_clear_vfta(struct ixgbe_hw *hw); -static s32 ixgbe_init_rx_addrs(struct ixgbe_hw *hw); +static void ixgbe_enable_rar(struct ixgbe_hw *hw, u32 index); +static void ixgbe_disable_rar(struct ixgbe_hw *hw, u32 index); static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr); static void ixgbe_add_mc_addr(struct ixgbe_hw *hw, u8 *mc_addr); +static void ixgbe_add_uc_addr(struct ixgbe_hw *hw, u8 *addr, u32 vmdq); /** - * ixgbe_start_hw - Prepare hardware for TX/RX + * ixgbe_start_hw_generic - Prepare hardware for Tx/Rx * @hw: pointer to hardware structure * * Starts the hardware by filling the bus info structure and media type, clears @@ -54,7 +61,7 @@ static void ixgbe_add_mc_addr(struct ixgbe_hw *hw, u8 *mc_addr); * table, VLAN filter table, calls routine to set up link and flow control * settings, and leaves transmit and receive units disabled and uninitialized **/ -s32 ixgbe_start_hw(struct ixgbe_hw *hw) +s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw) { u32 ctrl_ext; @@ -62,22 +69,22 @@ s32 ixgbe_start_hw(struct ixgbe_hw *hw) hw->phy.media_type = hw->mac.ops.get_media_type(hw); /* Identify the PHY */ - ixgbe_identify_phy(hw); + hw->phy.ops.identify(hw); /* * Store MAC address from RAR0, clear receive address registers, and * clear the multicast table */ - ixgbe_init_rx_addrs(hw); + hw->mac.ops.init_rx_addrs(hw); /* Clear the VLAN filter table */ - ixgbe_clear_vfta(hw); + hw->mac.ops.clear_vfta(hw); /* Set up link */ hw->mac.ops.setup_link(hw); /* Clear statistics registers */ - ixgbe_clear_hw_cntrs(hw); + hw->mac.ops.clear_hw_cntrs(hw); /* Set No Snoop Disable */ ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT); @@ -92,34 +99,34 @@ s32 ixgbe_start_hw(struct ixgbe_hw *hw) } /** - * ixgbe_init_hw - Generic hardware initialization + * ixgbe_init_hw_generic - Generic hardware initialization * @hw: pointer to hardware structure * - * Initialize the hardware by reseting the hardware, filling the bus info + * Initialize the hardware by resetting the hardware, filling the bus info * structure and media type, clears all on chip counters, initializes receive * address registers, multicast table, VLAN filter table, calls routine to set * up link and flow control settings, and leaves transmit and receive units * disabled and uninitialized **/ -s32 ixgbe_init_hw(struct ixgbe_hw *hw) +s32 ixgbe_init_hw_generic(struct ixgbe_hw *hw) { /* Reset the hardware */ - hw->mac.ops.reset(hw); + hw->mac.ops.reset_hw(hw); /* Start the HW */ - ixgbe_start_hw(hw); + hw->mac.ops.start_hw(hw); return 0; } /** - * ixgbe_clear_hw_cntrs - Generic clear hardware counters + * ixgbe_clear_hw_cntrs_generic - Generic clear hardware counters * @hw: pointer to hardware structure * * Clears all hardware statistics counters by reading them from the hardware * Statistics counters are clear on read. **/ -static s32 ixgbe_clear_hw_cntrs(struct ixgbe_hw *hw) +s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw) { u16 i = 0; @@ -191,7 +198,36 @@ static s32 ixgbe_clear_hw_cntrs(struct ixgbe_hw *hw) } /** - * ixgbe_get_mac_addr - Generic get MAC address + * ixgbe_read_pba_num_generic - Reads part number from EEPROM + * @hw: pointer to hardware structure + * @pba_num: stores the part number from the EEPROM + * + * Reads the part number from the EEPROM. + **/ +s32 ixgbe_read_pba_num_generic(struct ixgbe_hw *hw, u32 *pba_num) +{ + s32 ret_val; + u16 data; + + ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data); + if (ret_val) { + hw_dbg(hw, "NVM Read Error\n"); + return ret_val; + } + *pba_num = (u32)(data << 16); + + ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &data); + if (ret_val) { + hw_dbg(hw, "NVM Read Error\n"); + return ret_val; + } + *pba_num |= data; + + return 0; +} + +/** + * ixgbe_get_mac_addr_generic - Generic get MAC address * @hw: pointer to hardware structure * @mac_addr: Adapter MAC address * @@ -199,7 +235,7 @@ static s32 ixgbe_clear_hw_cntrs(struct ixgbe_hw *hw) * A reset of the adapter must be performed prior to calling this function * in order for the MAC address to have been loaded from the EEPROM into RAR0 **/ -s32 ixgbe_get_mac_addr(struct ixgbe_hw *hw, u8 *mac_addr) +s32 ixgbe_get_mac_addr_generic(struct ixgbe_hw *hw, u8 *mac_addr) { u32 rar_high; u32 rar_low; @@ -217,30 +253,8 @@ s32 ixgbe_get_mac_addr(struct ixgbe_hw *hw, u8 *mac_addr) return 0; } -s32 ixgbe_read_part_num(struct ixgbe_hw *hw, u32 *part_num) -{ - s32 ret_val; - u16 data; - - ret_val = ixgbe_read_eeprom(hw, IXGBE_PBANUM0_PTR, &data); - if (ret_val) { - hw_dbg(hw, "NVM Read Error\n"); - return ret_val; - } - *part_num = (u32)(data << 16); - - ret_val = ixgbe_read_eeprom(hw, IXGBE_PBANUM1_PTR, &data); - if (ret_val) { - hw_dbg(hw, "NVM Read Error\n"); - return ret_val; - } - *part_num |= data; - - return 0; -} - /** - * ixgbe_stop_adapter - Generic stop TX/RX units + * ixgbe_stop_adapter_generic - Generic stop Tx/Rx units * @hw: pointer to hardware structure * * Sets the adapter_stopped flag within ixgbe_hw struct. Clears interrupts, @@ -248,7 +262,7 @@ s32 ixgbe_read_part_num(struct ixgbe_hw *hw, u32 *part_num) * the shared code and drivers to determine if the adapter is in a stopped * state and should not touch the hardware. **/ -s32 ixgbe_stop_adapter(struct ixgbe_hw *hw) +s32 ixgbe_stop_adapter_generic(struct ixgbe_hw *hw) { u32 number_of_queues; u32 reg_val; @@ -264,6 +278,7 @@ s32 ixgbe_stop_adapter(struct ixgbe_hw *hw) reg_val = IXGBE_READ_REG(hw, IXGBE_RXCTRL); reg_val &= ~(IXGBE_RXCTRL_RXEN); IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, reg_val); + IXGBE_WRITE_FLUSH(hw); msleep(2); /* Clear interrupt mask to stop from interrupts being generated */ @@ -273,7 +288,7 @@ s32 ixgbe_stop_adapter(struct ixgbe_hw *hw) IXGBE_READ_REG(hw, IXGBE_EICR); /* Disable the transmit unit. Each queue must be disabled. */ - number_of_queues = hw->mac.num_tx_queues; + number_of_queues = hw->mac.max_tx_queues; for (i = 0; i < number_of_queues; i++) { reg_val = IXGBE_READ_REG(hw, IXGBE_TXDCTL(i)); if (reg_val & IXGBE_TXDCTL_ENABLE) { @@ -282,15 +297,22 @@ s32 ixgbe_stop_adapter(struct ixgbe_hw *hw) } } + /* + * Prevent the PCI-E bus from from hanging by disabling PCI-E master + * access and verify no pending requests + */ + if (ixgbe_disable_pcie_master(hw) != 0) + hw_dbg(hw, "PCI-E Master disable polling has failed.\n"); + return 0; } /** - * ixgbe_led_on - Turns on the software controllable LEDs. + * ixgbe_led_on_generic - Turns on the software controllable LEDs. * @hw: pointer to hardware structure * @index: led number to turn on **/ -s32 ixgbe_led_on(struct ixgbe_hw *hw, u32 index) +s32 ixgbe_led_on_generic(struct ixgbe_hw *hw, u32 index) { u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); @@ -304,11 +326,11 @@ s32 ixgbe_led_on(struct ixgbe_hw *hw, u32 index) } /** - * ixgbe_led_off - Turns off the software controllable LEDs. + * ixgbe_led_off_generic - Turns off the software controllable LEDs. * @hw: pointer to hardware structure * @index: led number to turn off **/ -s32 ixgbe_led_off(struct ixgbe_hw *hw, u32 index) +s32 ixgbe_led_off_generic(struct ixgbe_hw *hw, u32 index) { u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); @@ -321,15 +343,14 @@ s32 ixgbe_led_off(struct ixgbe_hw *hw, u32 index) return 0; } - /** - * ixgbe_init_eeprom - Initialize EEPROM params + * ixgbe_init_eeprom_params_generic - Initialize EEPROM params * @hw: pointer to hardware structure * * Initializes the EEPROM parameters ixgbe_eeprom_info within the * ixgbe_hw struct in order to set up EEPROM access. **/ -s32 ixgbe_init_eeprom(struct ixgbe_hw *hw) +s32 ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw) { struct ixgbe_eeprom_info *eeprom = &hw->eeprom; u32 eec; @@ -337,6 +358,9 @@ s32 ixgbe_init_eeprom(struct ixgbe_hw *hw) if (eeprom->type == ixgbe_eeprom_uninitialized) { eeprom->type = ixgbe_eeprom_none; + /* Set default semaphore delay to 10ms which is a well + * tested value */ + eeprom->semaphore_delay = 10; /* * Check for EEPROM present first. @@ -369,18 +393,85 @@ s32 ixgbe_init_eeprom(struct ixgbe_hw *hw) } /** - * ixgbe_read_eeprom - Read EEPROM word using EERD + * ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang + * @hw: pointer to hardware structure + * @offset: offset within the EEPROM to be read + * @data: read 16 bit value from EEPROM + * + * Reads 16 bit value from EEPROM through bit-bang method + **/ +s32 ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, + u16 *data) +{ + s32 status; + u16 word_in; + u8 read_opcode = IXGBE_EEPROM_READ_OPCODE_SPI; + + hw->eeprom.ops.init_params(hw); + + if (offset >= hw->eeprom.word_size) { + status = IXGBE_ERR_EEPROM; + goto out; + } + + /* Prepare the EEPROM for reading */ + status = ixgbe_acquire_eeprom(hw); + + if (status == 0) { + if (ixgbe_ready_eeprom(hw) != 0) { + ixgbe_release_eeprom(hw); + status = IXGBE_ERR_EEPROM; + } + } + + if (status == 0) { + ixgbe_standby_eeprom(hw); + + /* + * Some SPI eeproms use the 8th address bit embedded in the + * opcode + */ + if ((hw->eeprom.address_bits == 8) && (offset >= 128)) + read_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI; + + /* Send the READ command (opcode + addr) */ + ixgbe_shift_out_eeprom_bits(hw, read_opcode, + IXGBE_EEPROM_OPCODE_BITS); + ixgbe_shift_out_eeprom_bits(hw, (u16)(offset*2), + hw->eeprom.address_bits); + + /* Read the data. */ + word_in = ixgbe_shift_in_eeprom_bits(hw, 16); + *data = (word_in >> 8) | (word_in << 8); + + /* End this read operation */ + ixgbe_release_eeprom(hw); + } + +out: + return status; +} + +/** + * ixgbe_read_eeprom_generic - Read EEPROM word using EERD * @hw: pointer to hardware structure * @offset: offset of word in the EEPROM to read * @data: word read from the EEPROM * * Reads a 16 bit word from the EEPROM using the EERD register. **/ -s32 ixgbe_read_eeprom(struct ixgbe_hw *hw, u16 offset, u16 *data) +s32 ixgbe_read_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 *data) { u32 eerd; s32 status; + hw->eeprom.ops.init_params(hw); + + if (offset >= hw->eeprom.word_size) { + status = IXGBE_ERR_EEPROM; + goto out; + } + eerd = (offset << IXGBE_EEPROM_READ_ADDR_SHIFT) + IXGBE_EEPROM_READ_REG_START; @@ -389,10 +480,11 @@ s32 ixgbe_read_eeprom(struct ixgbe_hw *hw, u16 offset, u16 *data) if (status == 0) *data = (IXGBE_READ_REG(hw, IXGBE_EERD) >> - IXGBE_EEPROM_READ_REG_DATA); + IXGBE_EEPROM_READ_REG_DATA); else hw_dbg(hw, "Eeprom read timed out\n"); +out: return status; } @@ -420,6 +512,58 @@ static s32 ixgbe_poll_eeprom_eerd_done(struct ixgbe_hw *hw) } /** + * ixgbe_acquire_eeprom - Acquire EEPROM using bit-bang + * @hw: pointer to hardware structure + * + * Prepares EEPROM for access using bit-bang method. This function should + * be called before issuing a command to the EEPROM. + **/ +static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw) +{ + s32 status = 0; + u32 eec; + u32 i; + + if (ixgbe_acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0) + status = IXGBE_ERR_SWFW_SYNC; + + if (status == 0) { + eec = IXGBE_READ_REG(hw, IXGBE_EEC); + + /* Request EEPROM Access */ + eec |= IXGBE_EEC_REQ; + IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + + for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) { + eec = IXGBE_READ_REG(hw, IXGBE_EEC); + if (eec & IXGBE_EEC_GNT) + break; + udelay(5); + } + + /* Release if grant not acquired */ + if (!(eec & IXGBE_EEC_GNT)) { + eec &= ~IXGBE_EEC_REQ; + IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + hw_dbg(hw, "Could not acquire EEPROM grant\n"); + + ixgbe_release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); + status = IXGBE_ERR_EEPROM; + } + } + + /* Setup EEPROM for Read/Write */ + if (status == 0) { + /* Clear CS and SK */ + eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK); + IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); + } + return status; +} + +/** * ixgbe_get_eeprom_semaphore - Get hardware semaphore * @hw: pointer to hardware structure * @@ -475,7 +619,7 @@ static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw) */ if (i >= timeout) { hw_dbg(hw, "Driver can't access the Eeprom - Semaphore " - "not granted.\n"); + "not granted.\n"); ixgbe_release_eeprom_semaphore(hw); status = IXGBE_ERR_EEPROM; } @@ -503,6 +647,217 @@ static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw) } /** + * ixgbe_ready_eeprom - Polls for EEPROM ready + * @hw: pointer to hardware structure + **/ +static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw) +{ + s32 status = 0; + u16 i; + u8 spi_stat_reg; + + /* + * Read "Status Register" repeatedly until the LSB is cleared. The + * EEPROM will signal that the command has been completed by clearing + * bit 0 of the internal status register. If it's not cleared within + * 5 milliseconds, then error out. + */ + for (i = 0; i < IXGBE_EEPROM_MAX_RETRY_SPI; i += 5) { + ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_RDSR_OPCODE_SPI, + IXGBE_EEPROM_OPCODE_BITS); + spi_stat_reg = (u8)ixgbe_shift_in_eeprom_bits(hw, 8); + if (!(spi_stat_reg & IXGBE_EEPROM_STATUS_RDY_SPI)) + break; + + udelay(5); + ixgbe_standby_eeprom(hw); + }; + + /* + * On some parts, SPI write time could vary from 0-20mSec on 3.3V + * devices (and only 0-5mSec on 5V devices) + */ + if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) { + hw_dbg(hw, "SPI EEPROM Status error\n"); + status = IXGBE_ERR_EEPROM; + } + + return status; +} + +/** + * ixgbe_standby_eeprom - Returns EEPROM to a "standby" state + * @hw: pointer to hardware structure + **/ +static void ixgbe_standby_eeprom(struct ixgbe_hw *hw) +{ + u32 eec; + + eec = IXGBE_READ_REG(hw, IXGBE_EEC); + + /* Toggle CS to flush commands */ + eec |= IXGBE_EEC_CS; + IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); + eec &= ~IXGBE_EEC_CS; + IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); +} + +/** + * ixgbe_shift_out_eeprom_bits - Shift data bits out to the EEPROM. + * @hw: pointer to hardware structure + * @data: data to send to the EEPROM + * @count: number of bits to shift out + **/ +static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, + u16 count) +{ + u32 eec; + u32 mask; + u32 i; + + eec = IXGBE_READ_REG(hw, IXGBE_EEC); + + /* + * Mask is used to shift "count" bits of "data" out to the EEPROM + * one bit at a time. Determine the starting bit based on count + */ + mask = 0x01 << (count - 1); + + for (i = 0; i < count; i++) { + /* + * A "1" is shifted out to the EEPROM by setting bit "DI" to a + * "1", and then raising and then lowering the clock (the SK + * bit controls the clock input to the EEPROM). A "0" is + * shifted out to the EEPROM by setting "DI" to "0" and then + * raising and then lowering the clock. + */ + if (data & mask) + eec |= IXGBE_EEC_DI; + else + eec &= ~IXGBE_EEC_DI; + + IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_FLUSH(hw); + + udelay(1); + + ixgbe_raise_eeprom_clk(hw, &eec); + ixgbe_lower_eeprom_clk(hw, &eec); + + /* + * Shift mask to signify next bit of data to shift in to the + * EEPROM + */ + mask = mask >> 1; + }; + + /* We leave the "DI" bit set to "0" when we leave this routine. */ + eec &= ~IXGBE_EEC_DI; + IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_FLUSH(hw); +} + +/** + * ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM + * @hw: pointer to hardware structure + **/ +static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count) +{ + u32 eec; + u32 i; + u16 data = 0; + + /* + * In order to read a register from the EEPROM, we need to shift + * 'count' bits in from the EEPROM. Bits are "shifted in" by raising + * the clock input to the EEPROM (setting the SK bit), and then reading + * the value of the "DO" bit. During this "shifting in" process the + * "DI" bit should always be clear. + */ + eec = IXGBE_READ_REG(hw, IXGBE_EEC); + + eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI); + + for (i = 0; i < count; i++) { + data = data << 1; + ixgbe_raise_eeprom_clk(hw, &eec); + + eec = IXGBE_READ_REG(hw, IXGBE_EEC); + + eec &= ~(IXGBE_EEC_DI); + if (eec & IXGBE_EEC_DO) + data |= 1; + + ixgbe_lower_eeprom_clk(hw, &eec); + } + + return data; +} + +/** + * ixgbe_raise_eeprom_clk - Raises the EEPROM's clock input. + * @hw: pointer to hardware structure + * @eec: EEC register's current value + **/ +static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) +{ + /* + * Raise the clock input to the EEPROM + * (setting the SK bit), then delay + */ + *eec = *eec | IXGBE_EEC_SK; + IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); +} + +/** + * ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input. + * @hw: pointer to hardware structure + * @eecd: EECD's current value + **/ +static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) +{ + /* + * Lower the clock input to the EEPROM (clearing the SK bit), then + * delay + */ + *eec = *eec & ~IXGBE_EEC_SK; + IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); +} + +/** + * ixgbe_release_eeprom - Release EEPROM, release semaphores + * @hw: pointer to hardware structure + **/ +static void ixgbe_release_eeprom(struct ixgbe_hw *hw) +{ + u32 eec; + + eec = IXGBE_READ_REG(hw, IXGBE_EEC); + + eec |= IXGBE_EEC_CS; /* Pull CS high */ + eec &= ~IXGBE_EEC_SK; /* Lower SCK */ + + IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_FLUSH(hw); + + udelay(1); + + /* Stop requesting EEPROM access */ + eec &= ~IXGBE_EEC_REQ; + IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + + ixgbe_release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); +} + +/** * ixgbe_calc_eeprom_checksum - Calculates and returns the checksum * @hw: pointer to hardware structure **/ @@ -517,7 +872,7 @@ static u16 ixgbe_calc_eeprom_checksum(struct ixgbe_hw *hw) /* Include 0x0-0x3F in the checksum */ for (i = 0; i < IXGBE_EEPROM_CHECKSUM; i++) { - if (ixgbe_read_eeprom(hw, i, &word) != 0) { + if (hw->eeprom.ops.read(hw, i, &word) != 0) { hw_dbg(hw, "EEPROM read failed\n"); break; } @@ -526,15 +881,15 @@ static u16 ixgbe_calc_eeprom_checksum(struct ixgbe_hw *hw) /* Include all data from pointers except for the fw pointer */ for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) { - ixgbe_read_eeprom(hw, i, &pointer); + hw->eeprom.ops.read(hw, i, &pointer); /* Make sure the pointer seems valid */ if (pointer != 0xFFFF && pointer != 0) { - ixgbe_read_eeprom(hw, pointer, &length); + hw->eeprom.ops.read(hw, pointer, &length); if (length != 0xFFFF && length != 0) { for (j = pointer+1; j <= pointer+length; j++) { - ixgbe_read_eeprom(hw, j, &word); + hw->eeprom.ops.read(hw, j, &word); checksum += word; } } @@ -547,14 +902,15 @@ static u16 ixgbe_calc_eeprom_checksum(struct ixgbe_hw *hw) } /** - * ixgbe_validate_eeprom_checksum - Validate EEPROM checksum + * ixgbe_validate_eeprom_checksum_generic - Validate EEPROM checksum * @hw: pointer to hardware structure * @checksum_val: calculated checksum * * Performs checksum calculation and validates the EEPROM checksum. If the * caller does not need checksum_val, the value can be NULL. **/ -s32 ixgbe_validate_eeprom_checksum(struct ixgbe_hw *hw, u16 *checksum_val) +s32 ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw *hw, + u16 *checksum_val) { s32 status; u16 checksum; @@ -565,12 +921,12 @@ s32 ixgbe_validate_eeprom_checksum(struct ixgbe_hw *hw, u16 *checksum_val) * not continue or we could be in for a very long wait while every * EEPROM read fails */ - status = ixgbe_read_eeprom(hw, 0, &checksum); + status = hw->eeprom.ops.read(hw, 0, &checksum); if (status == 0) { checksum = ixgbe_calc_eeprom_checksum(hw); - ixgbe_read_eeprom(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum); + hw->eeprom.ops.read(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum); /* * Verify read checksum from EEPROM is the same as @@ -590,6 +946,33 @@ s32 ixgbe_validate_eeprom_checksum(struct ixgbe_hw *hw, u16 *checksum_val) } /** + * ixgbe_update_eeprom_checksum_generic - Updates the EEPROM checksum + * @hw: pointer to hardware structure + **/ +s32 ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw) +{ + s32 status; + u16 checksum; + + /* + * Read the first word from the EEPROM. If this times out or fails, do + * not continue or we could be in for a very long wait while every + * EEPROM read fails + */ + status = hw->eeprom.ops.read(hw, 0, &checksum); + + if (status == 0) { + checksum = ixgbe_calc_eeprom_checksum(hw); + status = hw->eeprom.ops.write(hw, IXGBE_EEPROM_CHECKSUM, + checksum); + } else { + hw_dbg(hw, "EEPROM read failed\n"); + } + + return status; +} + +/** * ixgbe_validate_mac_addr - Validate MAC address * @mac_addr: pointer to MAC address. * @@ -607,61 +990,140 @@ s32 ixgbe_validate_mac_addr(u8 *mac_addr) status = IXGBE_ERR_INVALID_MAC_ADDR; /* Reject the zero address */ else if (mac_addr[0] == 0 && mac_addr[1] == 0 && mac_addr[2] == 0 && - mac_addr[3] == 0 && mac_addr[4] == 0 && mac_addr[5] == 0) + mac_addr[3] == 0 && mac_addr[4] == 0 && mac_addr[5] == 0) status = IXGBE_ERR_INVALID_MAC_ADDR; return status; } /** - * ixgbe_set_rar - Set RX address register + * ixgbe_set_rar_generic - Set Rx address register * @hw: pointer to hardware structure - * @addr: Address to put into receive address register * @index: Receive address register to write - * @vind: Vind to set RAR to + * @addr: Address to put into receive address register + * @vmdq: VMDq "set" or "pool" index * @enable_addr: set flag that address is active * * Puts an ethernet address into a receive address register. **/ -s32 ixgbe_set_rar(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vind, - u32 enable_addr) +s32 ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq, + u32 enable_addr) { u32 rar_low, rar_high; + u32 rar_entries = hw->mac.num_rar_entries; - /* - * HW expects these in little endian so we reverse the byte order from - * network order (big endian) to little endian - */ - rar_low = ((u32)addr[0] | - ((u32)addr[1] << 8) | - ((u32)addr[2] << 16) | - ((u32)addr[3] << 24)); + /* setup VMDq pool selection before this RAR gets enabled */ + hw->mac.ops.set_vmdq(hw, index, vmdq); - rar_high = ((u32)addr[4] | - ((u32)addr[5] << 8) | - ((vind << IXGBE_RAH_VIND_SHIFT) & IXGBE_RAH_VIND_MASK)); + /* Make sure we are using a valid rar index range */ + if (index < rar_entries) { + /* + * HW expects these in little endian so we reverse the byte + * order from network order (big endian) to little endian + */ + rar_low = ((u32)addr[0] | + ((u32)addr[1] << 8) | + ((u32)addr[2] << 16) | + ((u32)addr[3] << 24)); + /* + * Some parts put the VMDq setting in the extra RAH bits, + * so save everything except the lower 16 bits that hold part + * of the address and the address valid bit. + */ + rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); + rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); + rar_high |= ((u32)addr[4] | ((u32)addr[5] << 8)); - if (enable_addr != 0) - rar_high |= IXGBE_RAH_AV; + if (enable_addr != 0) + rar_high |= IXGBE_RAH_AV; - IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low); - IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); + IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low); + IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); + } else { + hw_dbg(hw, "RAR index %d is out of range.\n", index); + } return 0; } /** - * ixgbe_init_rx_addrs - Initializes receive address filters. + * ixgbe_clear_rar_generic - Remove Rx address register + * @hw: pointer to hardware structure + * @index: Receive address register to write + * + * Clears an ethernet address from a receive address register. + **/ +s32 ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index) +{ + u32 rar_high; + u32 rar_entries = hw->mac.num_rar_entries; + + /* Make sure we are using a valid rar index range */ + if (index < rar_entries) { + /* + * Some parts put the VMDq setting in the extra RAH bits, + * so save everything except the lower 16 bits that hold part + * of the address and the address valid bit. + */ + rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); + rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); + + IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0); + IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); + } else { + hw_dbg(hw, "RAR index %d is out of range.\n", index); + } + + /* clear VMDq pool/queue selection for this RAR */ + hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL); + + return 0; +} + +/** + * ixgbe_enable_rar - Enable Rx address register + * @hw: pointer to hardware structure + * @index: index into the RAR table + * + * Enables the select receive address register. + **/ +static void ixgbe_enable_rar(struct ixgbe_hw *hw, u32 index) +{ + u32 rar_high; + + rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); + rar_high |= IXGBE_RAH_AV; + IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); +} + +/** + * ixgbe_disable_rar - Disable Rx address register + * @hw: pointer to hardware structure + * @index: index into the RAR table + * + * Disables the select receive address register. + **/ +static void ixgbe_disable_rar(struct ixgbe_hw *hw, u32 index) +{ + u32 rar_high; + + rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); + rar_high &= (~IXGBE_RAH_AV); + IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); +} + +/** + * ixgbe_init_rx_addrs_generic - Initializes receive address filters. * @hw: pointer to hardware structure * * Places the MAC address in receive address register 0 and clears the rest - * of the receive addresss registers. Clears the multicast table. Assumes + * of the receive address registers. Clears the multicast table. Assumes * the receiver is in reset when the routine is called. **/ -static s32 ixgbe_init_rx_addrs(struct ixgbe_hw *hw) +s32 ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw) { u32 i; - u32 rar_entries = hw->mac.num_rx_addrs; + u32 rar_entries = hw->mac.num_rar_entries; /* * If the current mac address is valid, assume it is a software override @@ -671,29 +1133,30 @@ static s32 ixgbe_init_rx_addrs(struct ixgbe_hw *hw) if (ixgbe_validate_mac_addr(hw->mac.addr) == IXGBE_ERR_INVALID_MAC_ADDR) { /* Get the MAC address from the RAR0 for later reference */ - ixgbe_get_mac_addr(hw, hw->mac.addr); + hw->mac.ops.get_mac_addr(hw, hw->mac.addr); hw_dbg(hw, " Keeping Current RAR0 Addr =%.2X %.2X %.2X ", - hw->mac.addr[0], hw->mac.addr[1], - hw->mac.addr[2]); + hw->mac.addr[0], hw->mac.addr[1], + hw->mac.addr[2]); hw_dbg(hw, "%.2X %.2X %.2X\n", hw->mac.addr[3], - hw->mac.addr[4], hw->mac.addr[5]); + hw->mac.addr[4], hw->mac.addr[5]); } else { /* Setup the receive address. */ hw_dbg(hw, "Overriding MAC Address in RAR[0]\n"); hw_dbg(hw, " New MAC Addr =%.2X %.2X %.2X ", - hw->mac.addr[0], hw->mac.addr[1], - hw->mac.addr[2]); + hw->mac.addr[0], hw->mac.addr[1], + hw->mac.addr[2]); hw_dbg(hw, "%.2X %.2X %.2X\n", hw->mac.addr[3], - hw->mac.addr[4], hw->mac.addr[5]); + hw->mac.addr[4], hw->mac.addr[5]); - ixgbe_set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV); + hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV); } + hw->addr_ctrl.overflow_promisc = 0; hw->addr_ctrl.rar_used_count = 1; /* Zero out the other receive addresses. */ - hw_dbg(hw, "Clearing RAR[1-15]\n"); + hw_dbg(hw, "Clearing RAR[1-%d]\n", rar_entries - 1); for (i = 1; i < rar_entries; i++) { IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0); IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0); @@ -705,9 +1168,113 @@ static s32 ixgbe_init_rx_addrs(struct ixgbe_hw *hw) IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); hw_dbg(hw, " Clearing MTA\n"); - for (i = 0; i < IXGBE_MC_TBL_SIZE; i++) + for (i = 0; i < hw->mac.mcft_size; i++) IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0); + if (hw->mac.ops.init_uta_tables) + hw->mac.ops.init_uta_tables(hw); + + return 0; +} + +/** + * ixgbe_add_uc_addr - Adds a secondary unicast address. + * @hw: pointer to hardware structure + * @addr: new address + * + * Adds it to unused receive address register or goes into promiscuous mode. + **/ +static void ixgbe_add_uc_addr(struct ixgbe_hw *hw, u8 *addr, u32 vmdq) +{ + u32 rar_entries = hw->mac.num_rar_entries; + u32 rar; + + hw_dbg(hw, " UC Addr = %.2X %.2X %.2X %.2X %.2X %.2X\n", + addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]); + + /* + * Place this address in the RAR if there is room, + * else put the controller into promiscuous mode + */ + if (hw->addr_ctrl.rar_used_count < rar_entries) { + rar = hw->addr_ctrl.rar_used_count - + hw->addr_ctrl.mc_addr_in_rar_count; + hw->mac.ops.set_rar(hw, rar, addr, vmdq, IXGBE_RAH_AV); + hw_dbg(hw, "Added a secondary address to RAR[%d]\n", rar); + hw->addr_ctrl.rar_used_count++; + } else { + hw->addr_ctrl.overflow_promisc++; + } + + hw_dbg(hw, "ixgbe_add_uc_addr Complete\n"); +} + +/** + * ixgbe_update_uc_addr_list_generic - Updates MAC list of secondary addresses + * @hw: pointer to hardware structure + * @addr_list: the list of new addresses + * @addr_count: number of addresses + * @next: iterator function to walk the address list + * + * The given list replaces any existing list. Clears the secondary addrs from + * receive address registers. Uses unused receive address registers for the + * first secondary addresses, and falls back to promiscuous mode as needed. + * + * Drivers using secondary unicast addresses must set user_set_promisc when + * manually putting the device into promiscuous mode. + **/ +s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw, u8 *addr_list, + u32 addr_count, ixgbe_mc_addr_itr next) +{ + u8 *addr; + u32 i; + u32 old_promisc_setting = hw->addr_ctrl.overflow_promisc; + u32 uc_addr_in_use; + u32 fctrl; + u32 vmdq; + + /* + * Clear accounting of old secondary address list, + * don't count RAR[0] + */ + uc_addr_in_use = hw->addr_ctrl.rar_used_count - + hw->addr_ctrl.mc_addr_in_rar_count - 1; + hw->addr_ctrl.rar_used_count -= uc_addr_in_use; + hw->addr_ctrl.overflow_promisc = 0; + + /* Zero out the other receive addresses */ + hw_dbg(hw, "Clearing RAR[1-%d]\n", uc_addr_in_use); + for (i = 1; i <= uc_addr_in_use; i++) { + IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0); + IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0); + } + + /* Add the new addresses */ + for (i = 0; i < addr_count; i++) { + hw_dbg(hw, " Adding the secondary addresses:\n"); + addr = next(hw, &addr_list, &vmdq); + ixgbe_add_uc_addr(hw, addr, vmdq); + } + + if (hw->addr_ctrl.overflow_promisc) { + /* enable promisc if not already in overflow or set by user */ + if (!old_promisc_setting && !hw->addr_ctrl.user_set_promisc) { + hw_dbg(hw, " Entering address overflow promisc mode\n"); + fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL); + fctrl |= IXGBE_FCTRL_UPE; + IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl); + } + } else { + /* only disable if set by overflow, not by user */ + if (old_promisc_setting && !hw->addr_ctrl.user_set_promisc) { + hw_dbg(hw, " Leaving address overflow promisc mode\n"); + fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL); + fctrl &= ~IXGBE_FCTRL_UPE; + IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl); + } + } + + hw_dbg(hw, "ixgbe_update_uc_addr_list_generic Complete\n"); return 0; } @@ -720,7 +1287,7 @@ static s32 ixgbe_init_rx_addrs(struct ixgbe_hw *hw) * bit-vector to set in the multicast table. The hardware uses 12 bits, from * incoming rx multicast addresses, to determine the bit-vector to check in * the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set - * by the MO field of the MCSTCTRL. The MO field is set during initalization + * by the MO field of the MCSTCTRL. The MO field is set during initialization * to mc_filter_type. **/ static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr) @@ -728,19 +1295,19 @@ static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr) u32 vector = 0; switch (hw->mac.mc_filter_type) { - case 0: /* use bits [47:36] of the address */ + case 0: /* use bits [47:36] of the address */ vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4)); break; - case 1: /* use bits [46:35] of the address */ + case 1: /* use bits [46:35] of the address */ vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5)); break; - case 2: /* use bits [45:34] of the address */ + case 2: /* use bits [45:34] of the address */ vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6)); break; - case 3: /* use bits [43:32] of the address */ + case 3: /* use bits [43:32] of the address */ vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8)); break; - default: /* Invalid mc_filter_type */ + default: /* Invalid mc_filter_type */ hw_dbg(hw, "MC filter type param set incorrectly\n"); break; } @@ -794,21 +1361,22 @@ static void ixgbe_set_mta(struct ixgbe_hw *hw, u8 *mc_addr) **/ static void ixgbe_add_mc_addr(struct ixgbe_hw *hw, u8 *mc_addr) { - u32 rar_entries = hw->mac.num_rx_addrs; + u32 rar_entries = hw->mac.num_rar_entries; + u32 rar; hw_dbg(hw, " MC Addr =%.2X %.2X %.2X %.2X %.2X %.2X\n", - mc_addr[0], mc_addr[1], mc_addr[2], - mc_addr[3], mc_addr[4], mc_addr[5]); + mc_addr[0], mc_addr[1], mc_addr[2], + mc_addr[3], mc_addr[4], mc_addr[5]); /* * Place this multicast address in the RAR if there is room, * else put it in the MTA */ if (hw->addr_ctrl.rar_used_count < rar_entries) { - ixgbe_set_rar(hw, hw->addr_ctrl.rar_used_count, - mc_addr, 0, IXGBE_RAH_AV); - hw_dbg(hw, "Added a multicast address to RAR[%d]\n", - hw->addr_ctrl.rar_used_count); + /* use RAR from the end up for multicast */ + rar = rar_entries - hw->addr_ctrl.mc_addr_in_rar_count - 1; + hw->mac.ops.set_rar(hw, rar, mc_addr, 0, IXGBE_RAH_AV); + hw_dbg(hw, "Added a multicast address to RAR[%d]\n", rar); hw->addr_ctrl.rar_used_count++; hw->addr_ctrl.mc_addr_in_rar_count++; } else { @@ -819,22 +1387,23 @@ static void ixgbe_add_mc_addr(struct ixgbe_hw *hw, u8 *mc_addr) } /** - * ixgbe_update_mc_addr_list - Updates MAC list of multicast addresses + * ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses * @hw: pointer to hardware structure * @mc_addr_list: the list of new multicast addresses * @mc_addr_count: number of addresses - * @pad: number of bytes between addresses in the list + * @next: iterator function to walk the multicast address list * * The given list replaces any existing list. Clears the MC addrs from receive - * address registers and the multicast table. Uses unsed receive address + * address registers and the multicast table. Uses unused receive address * registers for the first multicast addresses, and hashes the rest into the * multicast table. **/ -s32 ixgbe_update_mc_addr_list(struct ixgbe_hw *hw, u8 *mc_addr_list, - u32 mc_addr_count, u32 pad) +s32 ixgbe_update_mc_addr_list_generic(struct ixgbe_hw *hw, u8 *mc_addr_list, + u32 mc_addr_count, ixgbe_mc_addr_itr next) { u32 i; - u32 rar_entries = hw->mac.num_rx_addrs; + u32 rar_entries = hw->mac.num_rar_entries; + u32 vmdq; /* * Set the new number of MC addresses that we are being requested to @@ -846,7 +1415,8 @@ s32 ixgbe_update_mc_addr_list(struct ixgbe_hw *hw, u8 *mc_addr_list, hw->addr_ctrl.mta_in_use = 0; /* Zero out the other receive addresses. */ - hw_dbg(hw, "Clearing RAR[1-15]\n"); + hw_dbg(hw, "Clearing RAR[%d-%d]\n", hw->addr_ctrl.rar_used_count, + rar_entries - 1); for (i = hw->addr_ctrl.rar_used_count; i < rar_entries; i++) { IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0); IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0); @@ -854,186 +1424,67 @@ s32 ixgbe_update_mc_addr_list(struct ixgbe_hw *hw, u8 *mc_addr_list, /* Clear the MTA */ hw_dbg(hw, " Clearing MTA\n"); - for (i = 0; i < IXGBE_MC_TBL_SIZE; i++) + for (i = 0; i < hw->mac.mcft_size; i++) IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0); /* Add the new addresses */ for (i = 0; i < mc_addr_count; i++) { hw_dbg(hw, " Adding the multicast addresses:\n"); - ixgbe_add_mc_addr(hw, mc_addr_list + - (i * (IXGBE_ETH_LENGTH_OF_ADDRESS + pad))); + ixgbe_add_mc_addr(hw, next(hw, &mc_addr_list, &vmdq)); } /* Enable mta */ if (hw->addr_ctrl.mta_in_use > 0) IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, - IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type); + IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type); - hw_dbg(hw, "ixgbe_update_mc_addr_list Complete\n"); + hw_dbg(hw, "ixgbe_update_mc_addr_list_generic Complete\n"); return 0; } /** - * ixgbe_clear_vfta - Clear VLAN filter table + * ixgbe_enable_mc_generic - Enable multicast address in RAR * @hw: pointer to hardware structure * - * Clears the VLAN filer table, and the VMDq index associated with the filter + * Enables multicast address in RAR and the use of the multicast hash table. **/ -static s32 ixgbe_clear_vfta(struct ixgbe_hw *hw) +s32 ixgbe_enable_mc_generic(struct ixgbe_hw *hw) { - u32 offset; - u32 vlanbyte; - - for (offset = 0; offset < IXGBE_VLAN_FILTER_TBL_SIZE; offset++) - IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0); - - for (vlanbyte = 0; vlanbyte < 4; vlanbyte++) - for (offset = 0; offset < IXGBE_VLAN_FILTER_TBL_SIZE; offset++) - IXGBE_WRITE_REG(hw, IXGBE_VFTAVIND(vlanbyte, offset), - 0); + u32 i; + u32 rar_entries = hw->mac.num_rar_entries; + struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; - return 0; -} + if (a->mc_addr_in_rar_count > 0) + for (i = (rar_entries - a->mc_addr_in_rar_count); + i < rar_entries; i++) + ixgbe_enable_rar(hw, i); -/** - * ixgbe_set_vfta - Set VLAN filter table - * @hw: pointer to hardware structure - * @vlan: VLAN id to write to VLAN filter - * @vind: VMDq output index that maps queue to VLAN id in VFTA - * @vlan_on: boolean flag to turn on/off VLAN in VFTA - * - * Turn on/off specified VLAN in the VLAN filter table. - **/ -s32 ixgbe_set_vfta(struct ixgbe_hw *hw, u32 vlan, u32 vind, - bool vlan_on) -{ - u32 VftaIndex; - u32 BitOffset; - u32 VftaReg; - u32 VftaByte; - - /* Determine 32-bit word position in array */ - VftaIndex = (vlan >> 5) & 0x7F; /* upper seven bits */ - - /* Determine the location of the (VMD) queue index */ - VftaByte = ((vlan >> 3) & 0x03); /* bits (4:3) indicating byte array */ - BitOffset = (vlan & 0x7) << 2; /* lower 3 bits indicate nibble */ - - /* Set the nibble for VMD queue index */ - VftaReg = IXGBE_READ_REG(hw, IXGBE_VFTAVIND(VftaByte, VftaIndex)); - VftaReg &= (~(0x0F << BitOffset)); - VftaReg |= (vind << BitOffset); - IXGBE_WRITE_REG(hw, IXGBE_VFTAVIND(VftaByte, VftaIndex), VftaReg); - - /* Determine the location of the bit for this VLAN id */ - BitOffset = vlan & 0x1F; /* lower five bits */ - - VftaReg = IXGBE_READ_REG(hw, IXGBE_VFTA(VftaIndex)); - if (vlan_on) - /* Turn on this VLAN id */ - VftaReg |= (1 << BitOffset); - else - /* Turn off this VLAN id */ - VftaReg &= ~(1 << BitOffset); - IXGBE_WRITE_REG(hw, IXGBE_VFTA(VftaIndex), VftaReg); + if (a->mta_in_use > 0) + IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, IXGBE_MCSTCTRL_MFE | + hw->mac.mc_filter_type); return 0; } /** - * ixgbe_setup_fc - Configure flow control settings + * ixgbe_disable_mc_generic - Disable multicast address in RAR * @hw: pointer to hardware structure - * @packetbuf_num: packet buffer number (0-7) * - * Configures the flow control settings based on SW configuration. - * This function is used for 802.3x flow control configuration only. + * Disables multicast address in RAR and the use of the multicast hash table. **/ -s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) +s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw) { - u32 frctl_reg; - u32 rmcs_reg; - - if (packetbuf_num < 0 || packetbuf_num > 7) - hw_dbg(hw, "Invalid packet buffer number [%d], expected range " - "is 0-7\n", packetbuf_num); - - frctl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL); - frctl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE); - - rmcs_reg = IXGBE_READ_REG(hw, IXGBE_RMCS); - rmcs_reg &= ~(IXGBE_RMCS_TFCE_PRIORITY | IXGBE_RMCS_TFCE_802_3X); - - /* - * We want to save off the original Flow Control configuration just in - * case we get disconnected and then reconnected into a different hub - * or switch with different Flow Control capabilities. - */ - hw->fc.type = hw->fc.original_type; - - /* - * The possible values of the "flow_control" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames but not - * send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but we do not - * support receiving pause frames) - * 3: Both Rx and TX flow control (symmetric) are enabled. - * other: Invalid. - */ - switch (hw->fc.type) { - case ixgbe_fc_none: - break; - case ixgbe_fc_rx_pause: - /* - * RX Flow control is enabled, - * and TX Flow control is disabled. - */ - frctl_reg |= IXGBE_FCTRL_RFCE; - break; - case ixgbe_fc_tx_pause: - /* - * TX Flow control is enabled, and RX Flow control is disabled, - * by a software over-ride. - */ - rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; - break; - case ixgbe_fc_full: - /* - * Flow control (both RX and TX) is enabled by a software - * over-ride. - */ - frctl_reg |= IXGBE_FCTRL_RFCE; - rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; - break; - default: - /* We should never get here. The value should be 0-3. */ - hw_dbg(hw, "Flow control param set incorrectly\n"); - break; - } - - /* Enable 802.3x based flow control settings. */ - IXGBE_WRITE_REG(hw, IXGBE_FCTRL, frctl_reg); - IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg); + u32 i; + u32 rar_entries = hw->mac.num_rar_entries; + struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; - /* - * We need to set up the Receive Threshold high and low water - * marks as well as (optionally) enabling the transmission of - * XON frames. - */ - if (hw->fc.type & ixgbe_fc_tx_pause) { - if (hw->fc.send_xon) { - IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), - (hw->fc.low_water | IXGBE_FCRTL_XONE)); - } else { - IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), - hw->fc.low_water); - } - IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num), - (hw->fc.high_water)|IXGBE_FCRTH_FCEN); - } + if (a->mc_addr_in_rar_count > 0) + for (i = (rar_entries - a->mc_addr_in_rar_count); + i < rar_entries; i++) + ixgbe_disable_rar(hw, i); - IXGBE_WRITE_REG(hw, IXGBE_FCTTV(0), hw->fc.pause_time); - IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1)); + if (a->mta_in_use > 0) + IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); return 0; } @@ -1049,13 +1500,24 @@ s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) **/ s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw) { - u32 ctrl; - s32 i; + u32 i; + u32 reg_val; + u32 number_of_queues; s32 status = IXGBE_ERR_MASTER_REQUESTS_PENDING; - ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL); - ctrl |= IXGBE_CTRL_GIO_DIS; - IXGBE_WRITE_REG(hw, IXGBE_CTRL, ctrl); + /* Disable the receive unit by stopping each queue */ + number_of_queues = hw->mac.max_rx_queues; + for (i = 0; i < number_of_queues; i++) { + reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i)); + if (reg_val & IXGBE_RXDCTL_ENABLE) { + reg_val &= ~IXGBE_RXDCTL_ENABLE; + IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val); + } + } + + reg_val = IXGBE_READ_REG(hw, IXGBE_CTRL); + reg_val |= IXGBE_CTRL_GIO_DIS; + IXGBE_WRITE_REG(hw, IXGBE_CTRL, reg_val); for (i = 0; i < IXGBE_PCI_MASTER_DISABLE_TIMEOUT; i++) { if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO)) { @@ -1070,11 +1532,11 @@ s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw) /** - * ixgbe_acquire_swfw_sync - Aquire SWFW semaphore + * ixgbe_acquire_swfw_sync - Acquire SWFW semaphore * @hw: pointer to hardware structure - * @mask: Mask to specify wich semaphore to acquire + * @mask: Mask to specify which semaphore to acquire * - * Aquires the SWFW semaphore throught the GSSR register for the specified + * Acquires the SWFW semaphore thought the GSSR register for the specified * function (CSR, PHY0, PHY1, EEPROM, Flash) **/ s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u16 mask) @@ -1116,9 +1578,9 @@ s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u16 mask) /** * ixgbe_release_swfw_sync - Release SWFW semaphore * @hw: pointer to hardware structure - * @mask: Mask to specify wich semaphore to release + * @mask: Mask to specify which semaphore to release * - * Releases the SWFW semaphore throught the GSSR register for the specified + * Releases the SWFW semaphore thought the GSSR register for the specified * function (CSR, PHY0, PHY1, EEPROM, Flash) **/ void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u16 mask) @@ -1135,45 +1597,3 @@ void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u16 mask) ixgbe_release_eeprom_semaphore(hw); } -/** - * ixgbe_read_analog_reg8 - Reads 8 bit Atlas analog register - * @hw: pointer to hardware structure - * @reg: analog register to read - * @val: read value - * - * Performs write operation to analog register specified. - **/ -s32 ixgbe_read_analog_reg8(struct ixgbe_hw *hw, u32 reg, u8 *val) -{ - u32 atlas_ctl; - - IXGBE_WRITE_REG(hw, IXGBE_ATLASCTL, - IXGBE_ATLASCTL_WRITE_CMD | (reg << 8)); - IXGBE_WRITE_FLUSH(hw); - udelay(10); - atlas_ctl = IXGBE_READ_REG(hw, IXGBE_ATLASCTL); - *val = (u8)atlas_ctl; - - return 0; -} - -/** - * ixgbe_write_analog_reg8 - Writes 8 bit Atlas analog register - * @hw: pointer to hardware structure - * @reg: atlas register to write - * @val: value to write - * - * Performs write operation to Atlas analog register specified. - **/ -s32 ixgbe_write_analog_reg8(struct ixgbe_hw *hw, u32 reg, u8 val) -{ - u32 atlas_ctl; - - atlas_ctl = (reg << 8) | val; - IXGBE_WRITE_REG(hw, IXGBE_ATLASCTL, atlas_ctl); - IXGBE_WRITE_FLUSH(hw); - udelay(10); - - return 0; -} - |
