summaryrefslogtreecommitdiffstats
path: root/drivers/net/ixgbe/ixgbe_82598.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ixgbe/ixgbe_82598.c')
-rw-r--r--drivers/net/ixgbe/ixgbe_82598.c192
1 files changed, 180 insertions, 12 deletions
diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c
index 7cddcfb..ad5699d 100644
--- a/drivers/net/ixgbe/ixgbe_82598.c
+++ b/drivers/net/ixgbe/ixgbe_82598.c
@@ -46,6 +46,8 @@ static s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw,
ixgbe_link_speed speed,
bool autoneg,
bool autoneg_wait_to_complete);
+static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
+ u8 *eeprom_data);
/**
*/
@@ -53,12 +55,40 @@ static s32 ixgbe_get_invariants_82598(struct ixgbe_hw *hw)
{
struct ixgbe_mac_info *mac = &hw->mac;
struct ixgbe_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u16 list_offset, data_offset;
/* Call PHY identify routine to get the phy type */
ixgbe_identify_phy_generic(hw);
/* PHY Init */
switch (phy->type) {
+ case ixgbe_phy_tn:
+ phy->ops.check_link = &ixgbe_check_phy_link_tnx;
+ phy->ops.get_firmware_version =
+ &ixgbe_get_phy_firmware_version_tnx;
+ break;
+ case ixgbe_phy_nl:
+ phy->ops.reset = &ixgbe_reset_phy_nl;
+
+ /* Call SFP+ identify routine to get the SFP+ module type */
+ ret_val = phy->ops.identify_sfp(hw);
+ if (ret_val != 0)
+ goto out;
+ else if (hw->phy.sfp_type == ixgbe_sfp_type_unknown) {
+ ret_val = IXGBE_ERR_SFP_NOT_SUPPORTED;
+ goto out;
+ }
+
+ /* Check to see if SFP+ module is supported */
+ ret_val = ixgbe_get_sfp_init_sequence_offsets(hw,
+ &list_offset,
+ &data_offset);
+ if (ret_val != 0) {
+ ret_val = IXGBE_ERR_SFP_NOT_SUPPORTED;
+ goto out;
+ }
+ break;
default:
break;
}
@@ -77,7 +107,8 @@ static s32 ixgbe_get_invariants_82598(struct ixgbe_hw *hw)
mac->max_rx_queues = IXGBE_82598_MAX_RX_QUEUES;
mac->max_tx_queues = IXGBE_82598_MAX_TX_QUEUES;
- return 0;
+out:
+ return ret_val;
}
/**
@@ -146,9 +177,9 @@ static s32 ixgbe_get_link_capabilities_82598(struct ixgbe_hw *hw,
*
* Determines the link capabilities by reading the AUTOC register.
**/
-s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw,
- ixgbe_link_speed *speed,
- bool *autoneg)
+static s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg)
{
s32 status = IXGBE_ERR_LINK_SETUP;
u16 speed_ability;
@@ -186,9 +217,15 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
case IXGBE_DEV_ID_82598AF_SINGLE_PORT:
case IXGBE_DEV_ID_82598EB_CX4:
case IXGBE_DEV_ID_82598_CX4_DUAL_PORT:
+ case IXGBE_DEV_ID_82598_DA_DUAL_PORT:
+ case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM:
case IXGBE_DEV_ID_82598EB_XF_LR:
+ case IXGBE_DEV_ID_82598EB_SFP_LOM:
media_type = ixgbe_media_type_fiber;
break;
+ case IXGBE_DEV_ID_82598AT:
+ media_type = ixgbe_media_type_copper;
+ break;
default:
media_type = ixgbe_media_type_unknown;
break;
@@ -205,7 +242,7 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
* Configures the flow control settings based on SW configuration. This
* function is used for 802.3x flow control configuration only.
**/
-s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
+static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
{
u32 frctl_reg;
u32 rmcs_reg;
@@ -391,6 +428,46 @@ static s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw,
{
u32 links_reg;
u32 i;
+ u16 link_reg, adapt_comp_reg;
+
+ /*
+ * SERDES PHY requires us to read link status from register 0xC79F.
+ * Bit 0 set indicates link is up/ready; clear indicates link down.
+ * 0xC00C is read to check that the XAUI lanes are active. Bit 0
+ * clear indicates active; set indicates inactive.
+ */
+ if (hw->phy.type == ixgbe_phy_nl) {
+ hw->phy.ops.read_reg(hw, 0xC79F, IXGBE_TWINAX_DEV, &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC79F, IXGBE_TWINAX_DEV, &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC00C, IXGBE_TWINAX_DEV,
+ &adapt_comp_reg);
+ if (link_up_wait_to_complete) {
+ for (i = 0; i < IXGBE_LINK_UP_TIME; i++) {
+ if ((link_reg & 1) &&
+ ((adapt_comp_reg & 1) == 0)) {
+ *link_up = true;
+ break;
+ } else {
+ *link_up = false;
+ }
+ msleep(100);
+ hw->phy.ops.read_reg(hw, 0xC79F,
+ IXGBE_TWINAX_DEV,
+ &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC00C,
+ IXGBE_TWINAX_DEV,
+ &adapt_comp_reg);
+ }
+ } else {
+ if ((link_reg & 1) && ((adapt_comp_reg & 1) == 0))
+ *link_up = true;
+ else
+ *link_up = false;
+ }
+
+ if (*link_up == false)
+ goto out;
+ }
links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
if (link_up_wait_to_complete) {
@@ -416,6 +493,7 @@ static s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw,
else
*speed = IXGBE_LINK_SPEED_1GB_FULL;
+out:
return 0;
}
@@ -648,7 +726,7 @@ static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
* @rar: receive address register index to associate with a VMDq index
* @vmdq: VMDq set index
**/
-s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
+static s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
{
u32 rar_high;
@@ -692,8 +770,8 @@ static s32 ixgbe_clear_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
*
* Turn on/off specified VLAN in the VLAN filter table.
**/
-s32 ixgbe_set_vfta_82598(struct ixgbe_hw *hw, u32 vlan, u32 vind,
- bool vlan_on)
+static s32 ixgbe_set_vfta_82598(struct ixgbe_hw *hw, u32 vlan, u32 vind,
+ bool vlan_on)
{
u32 regindex;
u32 bitindex;
@@ -816,7 +894,7 @@ static s32 ixgbe_blink_led_stop_82598(struct ixgbe_hw *hw, u32 index)
*
* Performs read operation to Atlas analog register specified.
**/
-s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
+static s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
{
u32 atlas_ctl;
@@ -838,7 +916,7 @@ s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
*
* Performs write operation to Atlas analog register specified.
**/
-s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
+static s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
{
u32 atlas_ctl;
@@ -851,12 +929,75 @@ s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
}
/**
+ * ixgbe_read_i2c_eeprom_82598 - Read 8 bit EEPROM word of an SFP+ module
+ * over I2C interface through an intermediate phy.
+ * @hw: pointer to hardware structure
+ * @byte_offset: EEPROM byte offset to read
+ * @eeprom_data: value read
+ *
+ * Performs byte read operation to SFP module's EEPROM over I2C interface.
+ **/
+static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
+ u8 *eeprom_data)
+{
+ s32 status = 0;
+ u16 sfp_addr = 0;
+ u16 sfp_data = 0;
+ u16 sfp_stat = 0;
+ u32 i;
+
+ if (hw->phy.type == ixgbe_phy_nl) {
+ /*
+ * phy SDA/SCL registers are at addresses 0xC30A to
+ * 0xC30D. These registers are used to talk to the SFP+
+ * module's EEPROM through the SDA/SCL (I2C) interface.
+ */
+ sfp_addr = (IXGBE_I2C_EEPROM_DEV_ADDR << 8) + byte_offset;
+ sfp_addr = (sfp_addr | IXGBE_I2C_EEPROM_READ_MASK);
+ hw->phy.ops.write_reg(hw,
+ IXGBE_MDIO_PMA_PMD_SDA_SCL_ADDR,
+ IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ sfp_addr);
+
+ /* Poll status */
+ for (i = 0; i < 100; i++) {
+ hw->phy.ops.read_reg(hw,
+ IXGBE_MDIO_PMA_PMD_SDA_SCL_STAT,
+ IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ &sfp_stat);
+ sfp_stat = sfp_stat & IXGBE_I2C_EEPROM_STATUS_MASK;
+ if (sfp_stat != IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS)
+ break;
+ msleep(10);
+ }
+
+ if (sfp_stat != IXGBE_I2C_EEPROM_STATUS_PASS) {
+ hw_dbg(hw, "EEPROM read did not pass.\n");
+ status = IXGBE_ERR_SFP_NOT_PRESENT;
+ goto out;
+ }
+
+ /* Read data */
+ hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_PMD_SDA_SCL_DATA,
+ IXGBE_MDIO_PMA_PMD_DEV_TYPE, &sfp_data);
+
+ *eeprom_data = (u8)(sfp_data >> 8);
+ } else {
+ status = IXGBE_ERR_PHY;
+ goto out;
+ }
+
+out:
+ return status;
+}
+
+/**
* ixgbe_get_supported_physical_layer_82598 - Returns physical layer type
* @hw: pointer to hardware structure
*
* Determines physical layer capabilities of the current configuration.
**/
-s32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
+static s32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
{
s32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
@@ -865,13 +1006,39 @@ s32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
case IXGBE_DEV_ID_82598_CX4_DUAL_PORT:
physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4;
break;
+ case IXGBE_DEV_ID_82598_DA_DUAL_PORT:
+ physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU;
+ break;
case IXGBE_DEV_ID_82598AF_DUAL_PORT:
case IXGBE_DEV_ID_82598AF_SINGLE_PORT:
+ case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM:
physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR;
break;
case IXGBE_DEV_ID_82598EB_XF_LR:
physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR;
break;
+ case IXGBE_DEV_ID_82598AT:
+ physical_layer = (IXGBE_PHYSICAL_LAYER_10GBASE_T |
+ IXGBE_PHYSICAL_LAYER_1000BASE_T);
+ break;
+ case IXGBE_DEV_ID_82598EB_SFP_LOM:
+ hw->phy.ops.identify_sfp(hw);
+
+ switch (hw->phy.sfp_type) {
+ case ixgbe_sfp_type_da_cu:
+ physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU;
+ break;
+ case ixgbe_sfp_type_sr:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR;
+ break;
+ case ixgbe_sfp_type_lr:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR;
+ break;
+ default:
+ physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
+ break;
+ }
+ break;
default:
physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
@@ -923,12 +1090,13 @@ static struct ixgbe_eeprom_operations eeprom_ops_82598 = {
static struct ixgbe_phy_operations phy_ops_82598 = {
.identify = &ixgbe_identify_phy_generic,
- /* .identify_sfp = &ixgbe_identify_sfp_module_generic, */
+ .identify_sfp = &ixgbe_identify_sfp_module_generic,
.reset = &ixgbe_reset_phy_generic,
.read_reg = &ixgbe_read_phy_reg_generic,
.write_reg = &ixgbe_write_phy_reg_generic,
.setup_link = &ixgbe_setup_phy_link_generic,
.setup_link_speed = &ixgbe_setup_phy_link_speed_generic,
+ .read_i2c_eeprom = &ixgbe_read_i2c_eeprom_82598,
};
struct ixgbe_info ixgbe_82598_info = {
OpenPOWER on IntegriCloud