summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/stmicro/stmmac/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/stmicro/stmmac/Kconfig')
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/Kconfig72
1 files changed, 6 insertions, 66 deletions
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index b02d4a3..7d3af19 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -14,62 +14,20 @@ config STMMAC_ETH
if STMMAC_ETH
config STMMAC_PLATFORM
- bool "STMMAC Platform bus support"
+ tristate "STMMAC Platform bus support"
depends on STMMAC_ETH
default y
---help---
- This selects the platform specific bus support for
- the stmmac device driver. This is the driver used
- on many embedded STM platforms based on ARM and SuperH
- processors.
+ This selects the platform specific bus support for the stmmac driver.
+ This is the driver used on several SoCs:
+ STi, Allwinner, Amlogic Meson, Altera SOCFPGA.
+
If you have a controller with this interface, say Y or M here.
If unsure, say N.
-config DWMAC_MESON
- bool "Amlogic Meson dwmac support"
- depends on STMMAC_PLATFORM && ARCH_MESON
- help
- Support for Ethernet controller on Amlogic Meson SoCs.
-
- This selects the Amlogic Meson SoC glue layer support for
- the stmmac device driver. This driver is used for Meson6 and
- Meson8 SoCs.
-
-config DWMAC_SOCFPGA
- bool "SOCFPGA dwmac support"
- depends on STMMAC_PLATFORM && MFD_SYSCON && (ARCH_SOCFPGA || COMPILE_TEST)
- help
- Support for ethernet controller on Altera SOCFPGA
-
- This selects the Altera SOCFPGA SoC glue layer support
- for the stmmac device driver. This driver is used for
- arria5 and cyclone5 FPGA SoCs.
-
-config DWMAC_SUNXI
- bool "Allwinner GMAC support"
- depends on STMMAC_PLATFORM && ARCH_SUNXI
- default y
- ---help---
- Support for Allwinner A20/A31 GMAC ethernet controllers.
-
- This selects Allwinner SoC glue layer support for the
- stmmac device driver. This driver is used for A20/A31
- GMAC ethernet controller.
-
-config DWMAC_STI
- bool "STi GMAC support"
- depends on STMMAC_PLATFORM && ARCH_STI
- default y
- ---help---
- Support for ethernet controller on STi SOCs.
-
- This selects STi SoC glue layer support for the stmmac
- device driver. This driver is used on for the STi series
- SOCs GMAC ethernet controller.
-
config STMMAC_PCI
- bool "STMMAC PCI bus support"
+ tristate "STMMAC PCI bus support"
depends on STMMAC_ETH && PCI
---help---
This is to select the Synopsys DWMAC available on PCI devices,
@@ -79,22 +37,4 @@ config STMMAC_PCI
D1215994A VIRTEX FPGA board.
If unsure, say N.
-
-config STMMAC_DEBUG_FS
- bool "Enable monitoring via sysFS "
- default n
- depends on STMMAC_ETH && DEBUG_FS
- ---help---
- The stmmac entry in /sys reports DMA TX/RX rings
- or (if supported) the HW cap register.
-
-config STMMAC_DA
- bool "STMMAC DMA arbitration scheme"
- default n
- ---help---
- Selecting this option, rx has priority over Tx (only for Giga
- Ethernet device).
- By default, the DMA arbitration scheme is based on Round-robin
- (rx:tx priority is 1:1).
-
endif
OpenPOWER on IntegriCloud