diff options
Diffstat (limited to 'drivers/net/ethernet/8390/hp-plus.c')
| -rw-r--r-- | drivers/net/ethernet/8390/hp-plus.c | 505 |
1 files changed, 0 insertions, 505 deletions
diff --git a/drivers/net/ethernet/8390/hp-plus.c b/drivers/net/ethernet/8390/hp-plus.c deleted file mode 100644 index 52f70f9..0000000 --- a/drivers/net/ethernet/8390/hp-plus.c +++ /dev/null @@ -1,505 +0,0 @@ -/* hp-plus.c: A HP PCLAN/plus ethernet driver for linux. */ -/* - Written 1994 by Donald Becker. - - This driver is for the Hewlett Packard PC LAN (27***) plus ethercards. - These cards are sold under several model numbers, usually 2724*. - - This software may be used and distributed according to the terms - of the GNU General Public License, incorporated herein by reference. - - The author may be reached as becker@scyld.com, or C/O - Scyld Computing Corporation - 410 Severn Ave., Suite 210 - Annapolis MD 21403 - - As is often the case, a great deal of credit is owed to Russ Nelson. - The Crynwr packet driver was my primary source of HP-specific - programming information. -*/ - -static const char version[] = -"hp-plus.c:v1.10 9/24/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n"; - -#include <linux/module.h> - -#include <linux/string.h> /* Important -- this inlines word moves. */ -#include <linux/kernel.h> -#include <linux/errno.h> -#include <linux/ioport.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/delay.h> - -#include <asm/io.h> - -#include "8390.h" - -#define DRV_NAME "hp-plus" - -/* A zero-terminated list of I/O addresses to be probed. */ -static unsigned int hpplus_portlist[] __initdata = -{0x200, 0x240, 0x280, 0x2C0, 0x300, 0x320, 0x340, 0}; - -/* - The HP EtherTwist chip implementation is a fairly routine DP8390 - implementation. It allows both shared memory and programmed-I/O buffer - access, using a custom interface for both. The programmed-I/O mode is - entirely implemented in the HP EtherTwist chip, bypassing the problem - ridden built-in 8390 facilities used on NE2000 designs. The shared - memory mode is likewise special, with an offset register used to make - packets appear at the shared memory base. Both modes use a base and bounds - page register to hide the Rx ring buffer wrap -- a packet that spans the - end of physical buffer memory appears continuous to the driver. (c.f. the - 3c503 and Cabletron E2100) - - A special note: the internal buffer of the board is only 8 bits wide. - This lays several nasty traps for the unaware: - - the 8390 must be programmed for byte-wide operations - - all I/O and memory operations must work on whole words (the access - latches are serially preloaded and have no byte-swapping ability). - - This board is laid out in I/O space much like the earlier HP boards: - the first 16 locations are for the board registers, and the second 16 are - for the 8390. The board is easy to identify, with both a dedicated 16 bit - ID register and a constant 0x530* value in the upper bits of the paging - register. -*/ - -#define HP_ID 0x00 /* ID register, always 0x4850. */ -#define HP_PAGING 0x02 /* Registers visible @ 8-f, see PageName. */ -#define HPP_OPTION 0x04 /* Bitmapped options, see HP_Option. */ -#define HPP_OUT_ADDR 0x08 /* I/O output location in Perf_Page. */ -#define HPP_IN_ADDR 0x0A /* I/O input location in Perf_Page. */ -#define HP_DATAPORT 0x0c /* I/O data transfer in Perf_Page. */ -#define NIC_OFFSET 0x10 /* Offset to the 8390 registers. */ -#define HP_IO_EXTENT 32 - -#define HP_START_PG 0x00 /* First page of TX buffer */ -#define HP_STOP_PG 0x80 /* Last page +1 of RX ring */ - -/* The register set selected in HP_PAGING. */ -enum PageName { - Perf_Page = 0, /* Normal operation. */ - MAC_Page = 1, /* The ethernet address (+checksum). */ - HW_Page = 2, /* EEPROM-loaded hardware parameters. */ - LAN_Page = 4, /* Transceiver selection, testing, etc. */ - ID_Page = 6 }; - -/* The bit definitions for the HPP_OPTION register. */ -enum HP_Option { - NICReset = 1, ChipReset = 2, /* Active low, really UNreset. */ - EnableIRQ = 4, FakeIntr = 8, BootROMEnb = 0x10, IOEnb = 0x20, - MemEnable = 0x40, ZeroWait = 0x80, MemDisable = 0x1000, }; - -static int hpp_probe1(struct net_device *dev, int ioaddr); - -static void hpp_reset_8390(struct net_device *dev); -static int hpp_open(struct net_device *dev); -static int hpp_close(struct net_device *dev); -static void hpp_mem_block_input(struct net_device *dev, int count, - struct sk_buff *skb, int ring_offset); -static void hpp_mem_block_output(struct net_device *dev, int count, - const unsigned char *buf, int start_page); -static void hpp_mem_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, - int ring_page); -static void hpp_io_block_input(struct net_device *dev, int count, - struct sk_buff *skb, int ring_offset); -static void hpp_io_block_output(struct net_device *dev, int count, - const unsigned char *buf, int start_page); -static void hpp_io_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, - int ring_page); - - -/* Probe a list of addresses for an HP LAN+ adaptor. - This routine is almost boilerplate. */ - -static int __init do_hpp_probe(struct net_device *dev) -{ - int i; - int base_addr = dev->base_addr; - int irq = dev->irq; - - if (base_addr > 0x1ff) /* Check a single specified location. */ - return hpp_probe1(dev, base_addr); - else if (base_addr != 0) /* Don't probe at all. */ - return -ENXIO; - - for (i = 0; hpplus_portlist[i]; i++) { - if (hpp_probe1(dev, hpplus_portlist[i]) == 0) - return 0; - dev->irq = irq; - } - - return -ENODEV; -} - -#ifndef MODULE -struct net_device * __init hp_plus_probe(int unit) -{ - struct net_device *dev = alloc_eip_netdev(); - int err; - - if (!dev) - return ERR_PTR(-ENOMEM); - - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - - err = do_hpp_probe(dev); - if (err) - goto out; - return dev; -out: - free_netdev(dev); - return ERR_PTR(err); -} -#endif - -static const struct net_device_ops hpp_netdev_ops = { - .ndo_open = hpp_open, - .ndo_stop = hpp_close, - .ndo_start_xmit = eip_start_xmit, - .ndo_tx_timeout = eip_tx_timeout, - .ndo_get_stats = eip_get_stats, - .ndo_set_rx_mode = eip_set_multicast_list, - .ndo_validate_addr = eth_validate_addr, - .ndo_set_mac_address = eth_mac_addr, - .ndo_change_mtu = eth_change_mtu, -#ifdef CONFIG_NET_POLL_CONTROLLER - .ndo_poll_controller = eip_poll, -#endif -}; - - -/* Do the interesting part of the probe at a single address. */ -static int __init hpp_probe1(struct net_device *dev, int ioaddr) -{ - int i, retval; - unsigned char checksum = 0; - const char name[] = "HP-PC-LAN+"; - int mem_start; - static unsigned version_printed; - - if (!request_region(ioaddr, HP_IO_EXTENT, DRV_NAME)) - return -EBUSY; - - /* Check for the HP+ signature, 50 48 0x 53. */ - if (inw(ioaddr + HP_ID) != 0x4850 || - (inw(ioaddr + HP_PAGING) & 0xfff0) != 0x5300) { - retval = -ENODEV; - goto out; - } - - if (ei_debug && version_printed++ == 0) - printk(version); - - printk("%s: %s at %#3x, ", dev->name, name, ioaddr); - - /* Retrieve and checksum the station address. */ - outw(MAC_Page, ioaddr + HP_PAGING); - - for(i = 0; i < ETH_ALEN; i++) { - unsigned char inval = inb(ioaddr + 8 + i); - dev->dev_addr[i] = inval; - checksum += inval; - } - checksum += inb(ioaddr + 14); - - printk("%pM", dev->dev_addr); - - if (checksum != 0xff) { - printk(" bad checksum %2.2x.\n", checksum); - retval = -ENODEV; - goto out; - } else { - /* Point at the Software Configuration Flags. */ - outw(ID_Page, ioaddr + HP_PAGING); - printk(" ID %4.4x", inw(ioaddr + 12)); - } - - /* Read the IRQ line. */ - outw(HW_Page, ioaddr + HP_PAGING); - { - int irq = inb(ioaddr + 13) & 0x0f; - int option = inw(ioaddr + HPP_OPTION); - - dev->irq = irq; - if (option & MemEnable) { - mem_start = inw(ioaddr + 9) << 8; - printk(", IRQ %d, memory address %#x.\n", irq, mem_start); - } else { - mem_start = 0; - printk(", IRQ %d, programmed-I/O mode.\n", irq); - } - } - - /* Set the wrap registers for string I/O reads. */ - outw((HP_START_PG + TX_PAGES/2) | ((HP_STOP_PG - 1) << 8), ioaddr + 14); - - /* Set the base address to point to the NIC, not the "real" base! */ - dev->base_addr = ioaddr + NIC_OFFSET; - - dev->netdev_ops = &hpp_netdev_ops; - - ei_status.name = name; - ei_status.word16 = 0; /* Agggghhhhh! Debug time: 2 days! */ - ei_status.tx_start_page = HP_START_PG; - ei_status.rx_start_page = HP_START_PG + TX_PAGES/2; - ei_status.stop_page = HP_STOP_PG; - - ei_status.reset_8390 = &hpp_reset_8390; - ei_status.block_input = &hpp_io_block_input; - ei_status.block_output = &hpp_io_block_output; - ei_status.get_8390_hdr = &hpp_io_get_8390_hdr; - - /* Check if the memory_enable flag is set in the option register. */ - if (mem_start) { - ei_status.block_input = &hpp_mem_block_input; - ei_status.block_output = &hpp_mem_block_output; - ei_status.get_8390_hdr = &hpp_mem_get_8390_hdr; - dev->mem_start = mem_start; - ei_status.mem = ioremap(mem_start, - (HP_STOP_PG - HP_START_PG)*256); - if (!ei_status.mem) { - retval = -ENOMEM; - goto out; - } - ei_status.rmem_start = dev->mem_start + TX_PAGES/2*256; - dev->mem_end = ei_status.rmem_end - = dev->mem_start + (HP_STOP_PG - HP_START_PG)*256; - } - - outw(Perf_Page, ioaddr + HP_PAGING); - NS8390p_init(dev, 0); - /* Leave the 8390 and HP chip reset. */ - outw(inw(ioaddr + HPP_OPTION) & ~EnableIRQ, ioaddr + HPP_OPTION); - - retval = register_netdev(dev); - if (retval) - goto out1; - return 0; -out1: - iounmap(ei_status.mem); -out: - release_region(ioaddr, HP_IO_EXTENT); - return retval; -} - -static int -hpp_open(struct net_device *dev) -{ - int ioaddr = dev->base_addr - NIC_OFFSET; - int option_reg; - int retval; - - if ((retval = request_irq(dev->irq, eip_interrupt, 0, dev->name, dev))) { - return retval; - } - - /* Reset the 8390 and HP chip. */ - option_reg = inw(ioaddr + HPP_OPTION); - outw(option_reg & ~(NICReset + ChipReset), ioaddr + HPP_OPTION); - udelay(5); - /* Unreset the board and enable interrupts. */ - outw(option_reg | (EnableIRQ + NICReset + ChipReset), ioaddr + HPP_OPTION); - - /* Set the wrap registers for programmed-I/O operation. */ - outw(HW_Page, ioaddr + HP_PAGING); - outw((HP_START_PG + TX_PAGES/2) | ((HP_STOP_PG - 1) << 8), ioaddr + 14); - - /* Select the operational page. */ - outw(Perf_Page, ioaddr + HP_PAGING); - - return eip_open(dev); -} - -static int -hpp_close(struct net_device *dev) -{ - int ioaddr = dev->base_addr - NIC_OFFSET; - int option_reg = inw(ioaddr + HPP_OPTION); - - free_irq(dev->irq, dev); - eip_close(dev); - outw((option_reg & ~EnableIRQ) | MemDisable | NICReset | ChipReset, - ioaddr + HPP_OPTION); - - return 0; -} - -static void -hpp_reset_8390(struct net_device *dev) -{ - int ioaddr = dev->base_addr - NIC_OFFSET; - int option_reg = inw(ioaddr + HPP_OPTION); - - if (ei_debug > 1) printk("resetting the 8390 time=%ld...", jiffies); - - outw(option_reg & ~(NICReset + ChipReset), ioaddr + HPP_OPTION); - /* Pause a few cycles for the hardware reset to take place. */ - udelay(5); - ei_status.txing = 0; - outw(option_reg | (EnableIRQ + NICReset + ChipReset), ioaddr + HPP_OPTION); - - udelay(5); - - - if ((inb_p(ioaddr+NIC_OFFSET+EN0_ISR) & ENISR_RESET) == 0) - printk("%s: hp_reset_8390() did not complete.\n", dev->name); - - if (ei_debug > 1) printk("8390 reset done (%ld).", jiffies); -} - -/* The programmed-I/O version of reading the 4 byte 8390 specific header. - Note that transfer with the EtherTwist+ must be on word boundaries. */ - -static void -hpp_io_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page) -{ - int ioaddr = dev->base_addr - NIC_OFFSET; - - outw((ring_page<<8), ioaddr + HPP_IN_ADDR); - insw(ioaddr + HP_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr)>>1); -} - -/* Block input and output, similar to the Crynwr packet driver. */ - -static void -hpp_io_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset) -{ - int ioaddr = dev->base_addr - NIC_OFFSET; - char *buf = skb->data; - - outw(ring_offset, ioaddr + HPP_IN_ADDR); - insw(ioaddr + HP_DATAPORT, buf, count>>1); - if (count & 0x01) - buf[count-1] = inw(ioaddr + HP_DATAPORT); -} - -/* The corresponding shared memory versions of the above 2 functions. */ - -static void -hpp_mem_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page) -{ - int ioaddr = dev->base_addr - NIC_OFFSET; - int option_reg = inw(ioaddr + HPP_OPTION); - - outw((ring_page<<8), ioaddr + HPP_IN_ADDR); - outw(option_reg & ~(MemDisable + BootROMEnb), ioaddr + HPP_OPTION); - memcpy_fromio(hdr, ei_status.mem, sizeof(struct e8390_pkt_hdr)); - outw(option_reg, ioaddr + HPP_OPTION); - hdr->count = (le16_to_cpu(hdr->count) + 3) & ~3; /* Round up allocation. */ -} - -static void -hpp_mem_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset) -{ - int ioaddr = dev->base_addr - NIC_OFFSET; - int option_reg = inw(ioaddr + HPP_OPTION); - - outw(ring_offset, ioaddr + HPP_IN_ADDR); - - outw(option_reg & ~(MemDisable + BootROMEnb), ioaddr + HPP_OPTION); - - /* Caution: this relies on get_8390_hdr() rounding up count! - Also note that we *can't* use eth_io_copy_and_sum() because - it will not always copy "count" bytes (e.g. padded IP). */ - - memcpy_fromio(skb->data, ei_status.mem, count); - outw(option_reg, ioaddr + HPP_OPTION); -} - -/* A special note: we *must* always transfer >=16 bit words. - It's always safe to round up, so we do. */ -static void -hpp_io_block_output(struct net_device *dev, int count, - const unsigned char *buf, int start_page) -{ - int ioaddr = dev->base_addr - NIC_OFFSET; - outw(start_page << 8, ioaddr + HPP_OUT_ADDR); - outsl(ioaddr + HP_DATAPORT, buf, (count+3)>>2); -} - -static void -hpp_mem_block_output(struct net_device *dev, int count, - const unsigned char *buf, int start_page) -{ - int ioaddr = dev->base_addr - NIC_OFFSET; - int option_reg = inw(ioaddr + HPP_OPTION); - - outw(start_page << 8, ioaddr + HPP_OUT_ADDR); - outw(option_reg & ~(MemDisable + BootROMEnb), ioaddr + HPP_OPTION); - memcpy_toio(ei_status.mem, buf, (count + 3) & ~3); - outw(option_reg, ioaddr + HPP_OPTION); -} - - -#ifdef MODULE -#define MAX_HPP_CARDS 4 /* Max number of HPP cards per module */ -static struct net_device *dev_hpp[MAX_HPP_CARDS]; -static int io[MAX_HPP_CARDS]; -static int irq[MAX_HPP_CARDS]; - -module_param_array(io, int, NULL, 0); -module_param_array(irq, int, NULL, 0); -MODULE_PARM_DESC(io, "I/O port address(es)"); -MODULE_PARM_DESC(irq, "IRQ number(s); ignored if properly detected"); -MODULE_DESCRIPTION("HP PC-LAN+ ISA ethernet driver"); -MODULE_LICENSE("GPL"); - -/* This is set up so that only a single autoprobe takes place per call. -ISA device autoprobes on a running machine are not recommended. */ -int __init -init_module(void) -{ - struct net_device *dev; - int this_dev, found = 0; - - for (this_dev = 0; this_dev < MAX_HPP_CARDS; this_dev++) { - if (io[this_dev] == 0) { - if (this_dev != 0) break; /* only autoprobe 1st one */ - printk(KERN_NOTICE "hp-plus.c: Presently autoprobing (not recommended) for a single card.\n"); - } - dev = alloc_eip_netdev(); - if (!dev) - break; - dev->irq = irq[this_dev]; - dev->base_addr = io[this_dev]; - if (do_hpp_probe(dev) == 0) { - dev_hpp[found++] = dev; - continue; - } - free_netdev(dev); - printk(KERN_WARNING "hp-plus.c: No HP-Plus card found (i/o = 0x%x).\n", io[this_dev]); - break; - } - if (found) - return 0; - return -ENXIO; -} - -static void cleanup_card(struct net_device *dev) -{ - /* NB: hpp_close() handles free_irq */ - iounmap(ei_status.mem); - release_region(dev->base_addr - NIC_OFFSET, HP_IO_EXTENT); -} - -void __exit -cleanup_module(void) -{ - int this_dev; - - for (this_dev = 0; this_dev < MAX_HPP_CARDS; this_dev++) { - struct net_device *dev = dev_hpp[this_dev]; - if (dev) { - unregister_netdev(dev); - cleanup_card(dev); - free_netdev(dev); - } - } -} -#endif /* MODULE */ |
