diff options
Diffstat (limited to 'drivers/net/dsa')
-rw-r--r-- | drivers/net/dsa/mv88e6060.c | 114 | ||||
-rw-r--r-- | drivers/net/dsa/mv88e6060.h | 111 |
2 files changed, 149 insertions, 76 deletions
diff --git a/drivers/net/dsa/mv88e6060.c b/drivers/net/dsa/mv88e6060.c index 9093577..0527f48 100644 --- a/drivers/net/dsa/mv88e6060.c +++ b/drivers/net/dsa/mv88e6060.c @@ -15,9 +15,7 @@ #include <linux/netdevice.h> #include <linux/phy.h> #include <net/dsa.h> - -#define REG_PORT(p) (8 + (p)) -#define REG_GLOBAL 0x0f +#include "mv88e6060.h" static int reg_read(struct dsa_switch *ds, int addr, int reg) { @@ -67,13 +65,14 @@ static char *mv88e6060_probe(struct device *host_dev, int sw_addr) if (bus == NULL) return NULL; - ret = mdiobus_read(bus, sw_addr + REG_PORT(0), 0x03); + ret = mdiobus_read(bus, sw_addr + REG_PORT(0), PORT_SWITCH_ID); if (ret >= 0) { - if (ret == 0x0600) + if (ret == PORT_SWITCH_ID_6060) return "Marvell 88E6060 (A0)"; - if (ret == 0x0601 || ret == 0x0602) + if (ret == PORT_SWITCH_ID_6060_R1 || + ret == PORT_SWITCH_ID_6060_R2) return "Marvell 88E6060 (B0)"; - if ((ret & 0xfff0) == 0x0600) + if ((ret & PORT_SWITCH_ID_6060_MASK) == PORT_SWITCH_ID_6060) return "Marvell 88E6060"; } @@ -87,22 +86,26 @@ static int mv88e6060_switch_reset(struct dsa_switch *ds) unsigned long timeout; /* Set all ports to the disabled state. */ - for (i = 0; i < 6; i++) { - ret = REG_READ(REG_PORT(i), 0x04); - REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc); + for (i = 0; i < MV88E6060_PORTS; i++) { + ret = REG_READ(REG_PORT(i), PORT_CONTROL); + REG_WRITE(REG_PORT(i), PORT_CONTROL, + ret & ~PORT_CONTROL_STATE_MASK); } /* Wait for transmit queues to drain. */ usleep_range(2000, 4000); /* Reset the switch. */ - REG_WRITE(REG_GLOBAL, 0x0a, 0xa130); + REG_WRITE(REG_GLOBAL, GLOBAL_ATU_CONTROL, + GLOBAL_ATU_CONTROL_SWRESET | + GLOBAL_ATU_CONTROL_ATUSIZE_1024 | + GLOBAL_ATU_CONTROL_ATE_AGE_5MIN); /* Wait up to one second for reset to complete. */ timeout = jiffies + 1 * HZ; while (time_before(jiffies, timeout)) { - ret = REG_READ(REG_GLOBAL, 0x00); - if ((ret & 0x8000) == 0x0000) + ret = REG_READ(REG_GLOBAL, GLOBAL_STATUS); + if (ret & GLOBAL_STATUS_INIT_READY) break; usleep_range(1000, 2000); @@ -119,13 +122,15 @@ static int mv88e6060_setup_global(struct dsa_switch *ds) * set the maximum frame size to 1536 bytes, and mask all * interrupt sources. */ - REG_WRITE(REG_GLOBAL, 0x04, 0x0800); + REG_WRITE(REG_GLOBAL, GLOBAL_CONTROL, GLOBAL_CONTROL_MAX_FRAME_1536); /* Enable automatic address learning, set the address * database size to 1024 entries, and set the default aging * time to 5 minutes. */ - REG_WRITE(REG_GLOBAL, 0x0a, 0x2130); + REG_WRITE(REG_GLOBAL, GLOBAL_ATU_CONTROL, + GLOBAL_ATU_CONTROL_ATUSIZE_1024 | + GLOBAL_ATU_CONTROL_ATE_AGE_5MIN); return 0; } @@ -139,25 +144,30 @@ static int mv88e6060_setup_port(struct dsa_switch *ds, int p) * state to Forwarding. Additionally, if this is the CPU * port, enable Ingress and Egress Trailer tagging mode. */ - REG_WRITE(addr, 0x04, dsa_is_cpu_port(ds, p) ? 0x4103 : 0x0003); + REG_WRITE(addr, PORT_CONTROL, + dsa_is_cpu_port(ds, p) ? + PORT_CONTROL_TRAILER | + PORT_CONTROL_INGRESS_MODE | + PORT_CONTROL_STATE_FORWARDING : + PORT_CONTROL_STATE_FORWARDING); /* Port based VLAN map: give each port its own address * database, allow the CPU port to talk to each of the 'real' * ports, and allow each of the 'real' ports to only talk to * the CPU port. */ - REG_WRITE(addr, 0x06, - ((p & 0xf) << 12) | - (dsa_is_cpu_port(ds, p) ? - ds->phys_port_mask : - (1 << ds->dst->cpu_port))); + REG_WRITE(addr, PORT_VLAN_MAP, + ((p & 0xf) << PORT_VLAN_MAP_DBNUM_SHIFT) | + (dsa_is_cpu_port(ds, p) ? + ds->phys_port_mask : + BIT(ds->dst->cpu_port))); /* Port Association Vector: when learning source addresses * of packets, add the address to the address database using * a port bitmap that has only the bit for this port set and * the other bits clear. */ - REG_WRITE(addr, 0x0b, 1 << p); + REG_WRITE(addr, PORT_ASSOC_VECTOR, BIT(p)); return 0; } @@ -177,7 +187,7 @@ static int mv88e6060_setup(struct dsa_switch *ds) if (ret < 0) return ret; - for (i = 0; i < 6; i++) { + for (i = 0; i < MV88E6060_PORTS; i++) { ret = mv88e6060_setup_port(ds, i); if (ret < 0) return ret; @@ -188,16 +198,17 @@ static int mv88e6060_setup(struct dsa_switch *ds) static int mv88e6060_set_addr(struct dsa_switch *ds, u8 *addr) { - REG_WRITE(REG_GLOBAL, 0x01, (addr[0] << 8) | addr[1]); - REG_WRITE(REG_GLOBAL, 0x02, (addr[2] << 8) | addr[3]); - REG_WRITE(REG_GLOBAL, 0x03, (addr[4] << 8) | addr[5]); + /* Use the same MAC Address as FD Pause frames for all ports */ + REG_WRITE(REG_GLOBAL, GLOBAL_MAC_01, (addr[0] << 9) | addr[1]); + REG_WRITE(REG_GLOBAL, GLOBAL_MAC_23, (addr[2] << 8) | addr[3]); + REG_WRITE(REG_GLOBAL, GLOBAL_MAC_45, (addr[4] << 8) | addr[5]); return 0; } static int mv88e6060_port_to_phy_addr(int port) { - if (port >= 0 && port <= 5) + if (port >= 0 && port < MV88E6060_PORTS) return port; return -1; } @@ -225,54 +236,6 @@ mv88e6060_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val) return reg_write(ds, addr, regnum, val); } -static void mv88e6060_poll_link(struct dsa_switch *ds) -{ - int i; - - for (i = 0; i < DSA_MAX_PORTS; i++) { - struct net_device *dev; - int uninitialized_var(port_status); - int link; - int speed; - int duplex; - int fc; - - dev = ds->ports[i]; - if (dev == NULL) - continue; - - link = 0; - if (dev->flags & IFF_UP) { - port_status = reg_read(ds, REG_PORT(i), 0x00); - if (port_status < 0) - continue; - - link = !!(port_status & 0x1000); - } - - if (!link) { - if (netif_carrier_ok(dev)) { - netdev_info(dev, "link down\n"); - netif_carrier_off(dev); - } - continue; - } - - speed = (port_status & 0x0100) ? 100 : 10; - duplex = (port_status & 0x0200) ? 1 : 0; - fc = ((port_status & 0xc000) == 0xc000) ? 1 : 0; - - if (!netif_carrier_ok(dev)) { - netdev_info(dev, - "link up, %d Mb/s, %s duplex, flow control %sabled\n", - speed, - duplex ? "full" : "half", - fc ? "en" : "dis"); - netif_carrier_on(dev); - } - } -} - static struct dsa_switch_driver mv88e6060_switch_driver = { .tag_protocol = DSA_TAG_PROTO_TRAILER, .probe = mv88e6060_probe, @@ -280,7 +243,6 @@ static struct dsa_switch_driver mv88e6060_switch_driver = { .set_addr = mv88e6060_set_addr, .phy_read = mv88e6060_phy_read, .phy_write = mv88e6060_phy_write, - .poll_link = mv88e6060_poll_link, }; static int __init mv88e6060_init(void) diff --git a/drivers/net/dsa/mv88e6060.h b/drivers/net/dsa/mv88e6060.h new file mode 100644 index 0000000..cc9b2ed --- /dev/null +++ b/drivers/net/dsa/mv88e6060.h @@ -0,0 +1,111 @@ +/* + * drivers/net/dsa/mv88e6060.h - Marvell 88e6060 switch chip support + * Copyright (c) 2015 Neil Armstrong + * + * Based on mv88e6xxx.h + * Copyright (c) 2008 Marvell Semiconductor + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __MV88E6060_H +#define __MV88E6060_H + +#define MV88E6060_PORTS 6 + +#define REG_PORT(p) (0x8 + (p)) +#define PORT_STATUS 0x00 +#define PORT_STATUS_PAUSE_EN BIT(15) +#define PORT_STATUS_MY_PAUSE BIT(14) +#define PORT_STATUS_FC (PORT_STATUS_MY_PAUSE | PORT_STATUS_PAUSE_EN) +#define PORT_STATUS_RESOLVED BIT(13) +#define PORT_STATUS_LINK BIT(12) +#define PORT_STATUS_PORTMODE BIT(11) +#define PORT_STATUS_PHYMODE BIT(10) +#define PORT_STATUS_DUPLEX BIT(9) +#define PORT_STATUS_SPEED BIT(8) +#define PORT_SWITCH_ID 0x03 +#define PORT_SWITCH_ID_6060 0x0600 +#define PORT_SWITCH_ID_6060_MASK 0xfff0 +#define PORT_SWITCH_ID_6060_R1 0x0601 +#define PORT_SWITCH_ID_6060_R2 0x0602 +#define PORT_CONTROL 0x04 +#define PORT_CONTROL_FORCE_FLOW_CTRL BIT(15) +#define PORT_CONTROL_TRAILER BIT(14) +#define PORT_CONTROL_HEADER BIT(11) +#define PORT_CONTROL_INGRESS_MODE BIT(8) +#define PORT_CONTROL_VLAN_TUNNEL BIT(7) +#define PORT_CONTROL_STATE_MASK 0x03 +#define PORT_CONTROL_STATE_DISABLED 0x00 +#define PORT_CONTROL_STATE_BLOCKING 0x01 +#define PORT_CONTROL_STATE_LEARNING 0x02 +#define PORT_CONTROL_STATE_FORWARDING 0x03 +#define PORT_VLAN_MAP 0x06 +#define PORT_VLAN_MAP_DBNUM_SHIFT 12 +#define PORT_VLAN_MAP_TABLE_MASK 0x1f +#define PORT_ASSOC_VECTOR 0x0b +#define PORT_ASSOC_VECTOR_MONITOR BIT(15) +#define PORT_ASSOC_VECTOR_PAV_MASK 0x1f +#define PORT_RX_CNTR 0x10 +#define PORT_TX_CNTR 0x11 + +#define REG_GLOBAL 0x0f +#define GLOBAL_STATUS 0x00 +#define GLOBAL_STATUS_SW_MODE_MASK (0x3 << 12) +#define GLOBAL_STATUS_SW_MODE_0 (0x0 << 12) +#define GLOBAL_STATUS_SW_MODE_1 (0x1 << 12) +#define GLOBAL_STATUS_SW_MODE_2 (0x2 << 12) +#define GLOBAL_STATUS_SW_MODE_3 (0x3 << 12) +#define GLOBAL_STATUS_INIT_READY BIT(11) +#define GLOBAL_STATUS_ATU_FULL BIT(3) +#define GLOBAL_STATUS_ATU_DONE BIT(2) +#define GLOBAL_STATUS_PHY_INT BIT(1) +#define GLOBAL_STATUS_EEINT BIT(0) +#define GLOBAL_MAC_01 0x01 +#define GLOBAL_MAC_01_DIFF_ADDR BIT(8) +#define GLOBAL_MAC_23 0x02 +#define GLOBAL_MAC_45 0x03 +#define GLOBAL_CONTROL 0x04 +#define GLOBAL_CONTROL_DISCARD_EXCESS BIT(13) +#define GLOBAL_CONTROL_MAX_FRAME_1536 BIT(10) +#define GLOBAL_CONTROL_RELOAD_EEPROM BIT(9) +#define GLOBAL_CONTROL_CTRMODE BIT(8) +#define GLOBAL_CONTROL_ATU_FULL_EN BIT(3) +#define GLOBAL_CONTROL_ATU_DONE_EN BIT(2) +#define GLOBAL_CONTROL_PHYINT_EN BIT(1) +#define GLOBAL_CONTROL_EEPROM_DONE_EN BIT(0) +#define GLOBAL_ATU_CONTROL 0x0a +#define GLOBAL_ATU_CONTROL_SWRESET BIT(15) +#define GLOBAL_ATU_CONTROL_LEARNDIS BIT(14) +#define GLOBAL_ATU_CONTROL_ATUSIZE_256 (0x0 << 12) +#define GLOBAL_ATU_CONTROL_ATUSIZE_512 (0x1 << 12) +#define GLOBAL_ATU_CONTROL_ATUSIZE_1024 (0x2 << 12) +#define GLOBAL_ATU_CONTROL_ATE_AGE_SHIFT 4 +#define GLOBAL_ATU_CONTROL_ATE_AGE_MASK (0xff << 4) +#define GLOBAL_ATU_CONTROL_ATE_AGE_5MIN (0x13 << 4) +#define GLOBAL_ATU_OP 0x0b +#define GLOBAL_ATU_OP_BUSY BIT(15) +#define GLOBAL_ATU_OP_NOP (0 << 12) +#define GLOBAL_ATU_OP_FLUSH_ALL ((1 << 12) | GLOBAL_ATU_OP_BUSY) +#define GLOBAL_ATU_OP_FLUSH_UNLOCKED ((2 << 12) | GLOBAL_ATU_OP_BUSY) +#define GLOBAL_ATU_OP_LOAD_DB ((3 << 12) | GLOBAL_ATU_OP_BUSY) +#define GLOBAL_ATU_OP_GET_NEXT_DB ((4 << 12) | GLOBAL_ATU_OP_BUSY) +#define GLOBAL_ATU_OP_FLUSH_DB ((5 << 12) | GLOBAL_ATU_OP_BUSY) +#define GLOBAL_ATU_OP_FLUSH_UNLOCKED_DB ((6 << 12) | GLOBAL_ATU_OP_BUSY) +#define GLOBAL_ATU_DATA 0x0c +#define GLOBAL_ATU_DATA_PORT_VECTOR_MASK 0x3f0 +#define GLOBAL_ATU_DATA_PORT_VECTOR_SHIFT 4 +#define GLOBAL_ATU_DATA_STATE_MASK 0x0f +#define GLOBAL_ATU_DATA_STATE_UNUSED 0x00 +#define GLOBAL_ATU_DATA_STATE_UC_STATIC 0x0e +#define GLOBAL_ATU_DATA_STATE_UC_LOCKED 0x0f +#define GLOBAL_ATU_DATA_STATE_MC_STATIC 0x07 +#define GLOBAL_ATU_DATA_STATE_MC_LOCKED 0x0e +#define GLOBAL_ATU_MAC_01 0x0d +#define GLOBAL_ATU_MAC_23 0x0e +#define GLOBAL_ATU_MAC_45 0x0f + +#endif |