diff options
Diffstat (limited to 'drivers/net/bnx2x/bnx2x_link.c')
| -rw-r--r-- | drivers/net/bnx2x/bnx2x_link.c | 6735 |
1 files changed, 6735 insertions, 0 deletions
diff --git a/drivers/net/bnx2x/bnx2x_link.c b/drivers/net/bnx2x/bnx2x_link.c new file mode 100644 index 0000000..0383e30 --- /dev/null +++ b/drivers/net/bnx2x/bnx2x_link.c @@ -0,0 +1,6735 @@ +/* Copyright 2008-2009 Broadcom Corporation + * + * Unless you and Broadcom execute a separate written software license + * agreement governing use of this software, this software is licensed to you + * under the terms of the GNU General Public License version 2, available + * at http://www.gnu.org/licenses/old-licenses/gpl-2.0.html (the "GPL"). + * + * Notwithstanding the above, under no circumstances may you combine this + * software in any way with any other Broadcom software provided under a + * license other than the GPL, without Broadcom's express prior written + * consent. + * + * Written by Yaniv Rosner + * + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/pci.h> +#include <linux/netdevice.h> +#include <linux/delay.h> +#include <linux/ethtool.h> +#include <linux/mutex.h> + +#include "bnx2x.h" + +/********************************************************/ +#define ETH_HLEN 14 +#define ETH_OVREHEAD (ETH_HLEN + 8)/* 8 for CRC + VLAN*/ +#define ETH_MIN_PACKET_SIZE 60 +#define ETH_MAX_PACKET_SIZE 1500 +#define ETH_MAX_JUMBO_PACKET_SIZE 9600 +#define MDIO_ACCESS_TIMEOUT 1000 +#define BMAC_CONTROL_RX_ENABLE 2 + +/***********************************************************/ +/* Shortcut definitions */ +/***********************************************************/ + +#define NIG_LATCH_BC_ENABLE_MI_INT 0 + +#define NIG_STATUS_EMAC0_MI_INT \ + NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_EMAC0_MISC_MI_INT +#define NIG_STATUS_XGXS0_LINK10G \ + NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK10G +#define NIG_STATUS_XGXS0_LINK_STATUS \ + NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS +#define NIG_STATUS_XGXS0_LINK_STATUS_SIZE \ + NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS_SIZE +#define NIG_STATUS_SERDES0_LINK_STATUS \ + NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_SERDES0_LINK_STATUS +#define NIG_MASK_MI_INT \ + NIG_MASK_INTERRUPT_PORT0_REG_MASK_EMAC0_MISC_MI_INT +#define NIG_MASK_XGXS0_LINK10G \ + NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK10G +#define NIG_MASK_XGXS0_LINK_STATUS \ + NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK_STATUS +#define NIG_MASK_SERDES0_LINK_STATUS \ + NIG_MASK_INTERRUPT_PORT0_REG_MASK_SERDES0_LINK_STATUS + +#define MDIO_AN_CL73_OR_37_COMPLETE \ + (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | \ + MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE) + +#define XGXS_RESET_BITS \ + (MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_RSTB_HW | \ + MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_IDDQ | \ + MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN | \ + MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN_SD | \ + MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_TXD_FIFO_RSTB) + +#define SERDES_RESET_BITS \ + (MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_RSTB_HW | \ + MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_IDDQ | \ + MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN | \ + MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN_SD) + +#define AUTONEG_CL37 SHARED_HW_CFG_AN_ENABLE_CL37 +#define AUTONEG_CL73 SHARED_HW_CFG_AN_ENABLE_CL73 +#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM +#define AUTONEG_PARALLEL \ + SHARED_HW_CFG_AN_ENABLE_PARALLEL_DETECTION +#define AUTONEG_SGMII_FIBER_AUTODET \ + SHARED_HW_CFG_AN_EN_SGMII_FIBER_AUTO_DETECT +#define AUTONEG_REMOTE_PHY SHARED_HW_CFG_AN_ENABLE_REMOTE_PHY + +#define GP_STATUS_PAUSE_RSOLUTION_TXSIDE \ + MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE +#define GP_STATUS_PAUSE_RSOLUTION_RXSIDE \ + MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE +#define GP_STATUS_SPEED_MASK \ + MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK +#define GP_STATUS_10M MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M +#define GP_STATUS_100M MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M +#define GP_STATUS_1G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G +#define GP_STATUS_2_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G +#define GP_STATUS_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G +#define GP_STATUS_6G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G +#define GP_STATUS_10G_HIG \ + MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG +#define GP_STATUS_10G_CX4 \ + MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4 +#define GP_STATUS_12G_HIG \ + MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12G_HIG +#define GP_STATUS_12_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12_5G +#define GP_STATUS_13G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_13G +#define GP_STATUS_15G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_15G +#define GP_STATUS_16G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G +#define GP_STATUS_1G_KX MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX +#define GP_STATUS_10G_KX4 \ + MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4 + +#define LINK_10THD LINK_STATUS_SPEED_AND_DUPLEX_10THD +#define LINK_10TFD LINK_STATUS_SPEED_AND_DUPLEX_10TFD +#define LINK_100TXHD LINK_STATUS_SPEED_AND_DUPLEX_100TXHD +#define LINK_100T4 LINK_STATUS_SPEED_AND_DUPLEX_100T4 +#define LINK_100TXFD LINK_STATUS_SPEED_AND_DUPLEX_100TXFD +#define LINK_1000THD LINK_STATUS_SPEED_AND_DUPLEX_1000THD +#define LINK_1000TFD LINK_STATUS_SPEED_AND_DUPLEX_1000TFD +#define LINK_1000XFD LINK_STATUS_SPEED_AND_DUPLEX_1000XFD +#define LINK_2500THD LINK_STATUS_SPEED_AND_DUPLEX_2500THD +#define LINK_2500TFD LINK_STATUS_SPEED_AND_DUPLEX_2500TFD +#define LINK_2500XFD LINK_STATUS_SPEED_AND_DUPLEX_2500XFD +#define LINK_10GTFD LINK_STATUS_SPEED_AND_DUPLEX_10GTFD +#define LINK_10GXFD LINK_STATUS_SPEED_AND_DUPLEX_10GXFD +#define LINK_12GTFD LINK_STATUS_SPEED_AND_DUPLEX_12GTFD +#define LINK_12GXFD LINK_STATUS_SPEED_AND_DUPLEX_12GXFD +#define LINK_12_5GTFD LINK_STATUS_SPEED_AND_DUPLEX_12_5GTFD +#define LINK_12_5GXFD LINK_STATUS_SPEED_AND_DUPLEX_12_5GXFD +#define LINK_13GTFD LINK_STATUS_SPEED_AND_DUPLEX_13GTFD +#define LINK_13GXFD LINK_STATUS_SPEED_AND_DUPLEX_13GXFD +#define LINK_15GTFD LINK_STATUS_SPEED_AND_DUPLEX_15GTFD +#define LINK_15GXFD LINK_STATUS_SPEED_AND_DUPLEX_15GXFD +#define LINK_16GTFD LINK_STATUS_SPEED_AND_DUPLEX_16GTFD +#define LINK_16GXFD LINK_STATUS_SPEED_AND_DUPLEX_16GXFD + +#define PHY_XGXS_FLAG 0x1 +#define PHY_SGMII_FLAG 0x2 +#define PHY_SERDES_FLAG 0x4 + +/* */ +#define SFP_EEPROM_CON_TYPE_ADDR 0x2 + #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7 + #define SFP_EEPROM_CON_TYPE_VAL_COPPER 0x21 + + +#define SFP_EEPROM_COMP_CODE_ADDR 0x3 + #define SFP_EEPROM_COMP_CODE_SR_MASK (1<<4) + #define SFP_EEPROM_COMP_CODE_LR_MASK (1<<5) + #define SFP_EEPROM_COMP_CODE_LRM_MASK (1<<6) + +#define SFP_EEPROM_FC_TX_TECH_ADDR 0x8 + #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE 0x4 + #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE 0x8 + +#define SFP_EEPROM_OPTIONS_ADDR 0x40 + #define SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK 0x1 +#define SFP_EEPROM_OPTIONS_SIZE 2 + +#define EDC_MODE_LINEAR 0x0022 +#define EDC_MODE_LIMITING 0x0044 +#define EDC_MODE_PASSIVE_DAC 0x0055 + + + +/**********************************************************/ +/* INTERFACE */ +/**********************************************************/ +#define CL45_WR_OVER_CL22(_bp, _port, _phy_addr, _bank, _addr, _val) \ + bnx2x_cl45_write(_bp, _port, 0, _phy_addr, \ + DEFAULT_PHY_DEV_ADDR, \ + (_bank + (_addr & 0xf)), \ + _val) + +#define CL45_RD_OVER_CL22(_bp, _port, _phy_addr, _bank, _addr, _val) \ + bnx2x_cl45_read(_bp, _port, 0, _phy_addr, \ + DEFAULT_PHY_DEV_ADDR, \ + (_bank + (_addr & 0xf)), \ + _val) + +static void bnx2x_set_serdes_access(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u32 emac_base = (params->port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0; + + /* Set Clause 22 */ + REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + params->port*0x10, 1); + REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245f8000); + udelay(500); + REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245d000f); + udelay(500); + /* Set Clause 45 */ + REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + params->port*0x10, 0); +} +static void bnx2x_set_phy_mdio(struct link_params *params, u8 phy_flags) +{ + struct bnx2x *bp = params->bp; + + if (phy_flags & PHY_XGXS_FLAG) { + REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST + + params->port*0x18, 0); + REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + params->port*0x18, + DEFAULT_PHY_DEV_ADDR); + } else { + bnx2x_set_serdes_access(params); + + REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD + + params->port*0x10, + DEFAULT_PHY_DEV_ADDR); + } +} + +static u32 bnx2x_bits_en(struct bnx2x *bp, u32 reg, u32 bits) +{ + u32 val = REG_RD(bp, reg); + + val |= bits; + REG_WR(bp, reg, val); + return val; +} + +static u32 bnx2x_bits_dis(struct bnx2x *bp, u32 reg, u32 bits) +{ + u32 val = REG_RD(bp, reg); + + val &= ~bits; + REG_WR(bp, reg, val); + return val; +} + +static void bnx2x_emac_init(struct link_params *params, + struct link_vars *vars) +{ + /* reset and unreset the emac core */ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; + u32 val; + u16 timeout; + + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, + (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port)); + udelay(5); + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, + (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port)); + + /* init emac - use read-modify-write */ + /* self clear reset */ + val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); + EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET)); + + timeout = 200; + do { + val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); + DP(NETIF_MSG_LINK, "EMAC reset reg is %u\n", val); + if (!timeout) { + DP(NETIF_MSG_LINK, "EMAC timeout!\n"); + return; + } + timeout--; + } while (val & EMAC_MODE_RESET); + + /* Set mac address */ + val = ((params->mac_addr[0] << 8) | + params->mac_addr[1]); + EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH, val); + + val = ((params->mac_addr[2] << 24) | + (params->mac_addr[3] << 16) | + (params->mac_addr[4] << 8) | + params->mac_addr[5]); + EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + 4, val); +} + +static u8 bnx2x_emac_enable(struct link_params *params, + struct link_vars *vars, u8 lb) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; + u32 val; + + DP(NETIF_MSG_LINK, "enabling EMAC\n"); + + /* enable emac and not bmac */ + REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 1); + + /* for paladium */ + if (CHIP_REV_IS_EMUL(bp)) { + /* Use lane 1 (of lanes 0-3) */ + REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1); + REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + + port*4, 1); + } + /* for fpga */ + else + + if (CHIP_REV_IS_FPGA(bp)) { + /* Use lane 1 (of lanes 0-3) */ + DP(NETIF_MSG_LINK, "bnx2x_emac_enable: Setting FPGA\n"); + + REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1); + REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, + 0); + } else + /* ASIC */ + if (vars->phy_flags & PHY_XGXS_FLAG) { + u32 ser_lane = ((params->lane_config & + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); + + DP(NETIF_MSG_LINK, "XGXS\n"); + /* select the master lanes (out of 0-3) */ + REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + + port*4, ser_lane); + /* select XGXS */ + REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + + port*4, 1); + + } else { /* SerDes */ + DP(NETIF_MSG_LINK, "SerDes\n"); + /* select SerDes */ + REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + + port*4, 0); + } + + bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_RX_MODE, + EMAC_RX_MODE_RESET); + bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE, + EMAC_TX_MODE_RESET); + + if (CHIP_REV_IS_SLOW(bp)) { + /* config GMII mode */ + val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); + EMAC_WR(bp, EMAC_REG_EMAC_MODE, + (val | EMAC_MODE_PORT_GMII)); + } else { /* ASIC */ + /* pause enable/disable */ + bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_RX_MODE, + EMAC_RX_MODE_FLOW_EN); + if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX) + bnx2x_bits_en(bp, emac_base + + EMAC_REG_EMAC_RX_MODE, + EMAC_RX_MODE_FLOW_EN); + + bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_TX_MODE, + (EMAC_TX_MODE_EXT_PAUSE_EN | + EMAC_TX_MODE_FLOW_EN)); + if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) + bnx2x_bits_en(bp, emac_base + + EMAC_REG_EMAC_TX_MODE, + (EMAC_TX_MODE_EXT_PAUSE_EN | + EMAC_TX_MODE_FLOW_EN)); + } + + /* KEEP_VLAN_TAG, promiscuous */ + val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE); + val |= EMAC_RX_MODE_KEEP_VLAN_TAG | EMAC_RX_MODE_PROMISCUOUS; + EMAC_WR(bp, EMAC_REG_EMAC_RX_MODE, val); + + /* Set Loopback */ + val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); + if (lb) + val |= 0x810; + else + val &= ~0x810; + EMAC_WR(bp, EMAC_REG_EMAC_MODE, val); + + /* enable emac */ + REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 1); + + /* enable emac for jumbo packets */ + EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE, + (EMAC_RX_MTU_SIZE_JUMBO_ENA | + (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD))); + + /* strip CRC */ + REG_WR(bp, NIG_REG_NIG_INGRESS_EMAC0_NO_CRC + port*4, 0x1); + + /* disable the NIG in/out to the bmac */ + REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x0); + REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, 0x0); + REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x0); + + /* enable the NIG in/out to the emac */ + REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x1); + val = 0; + if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) + val = 1; + + REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, val); + REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x1); + + if (CHIP_REV_IS_EMUL(bp)) { + /* take the BigMac out of reset */ + REG_WR(bp, + GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + + /* enable access for bmac registers */ + REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1); + } else + REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x0); + + vars->mac_type = MAC_TYPE_EMAC; + return 0; +} + + + +static u8 bnx2x_bmac_enable(struct link_params *params, struct link_vars *vars, + u8 is_lb) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM : + NIG_REG_INGRESS_BMAC0_MEM; + u32 wb_data[2]; + u32 val; + + DP(NETIF_MSG_LINK, "Enabling BigMAC\n"); + /* reset and unreset the BigMac */ + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + msleep(1); + + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + + /* enable access for bmac registers */ + REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1); + + /* XGXS control */ + wb_data[0] = 0x3c; + wb_data[1] = 0; + REG_WR_DMAE(bp, bmac_addr + + BIGMAC_REGISTER_BMAC_XGXS_CONTROL, + wb_data, 2); + + /* tx MAC SA */ + wb_data[0] = ((params->mac_addr[2] << 24) | + (params->mac_addr[3] << 16) | + (params->mac_addr[4] << 8) | + params->mac_addr[5]); + wb_data[1] = ((params->mac_addr[0] << 8) | + params->mac_addr[1]); + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR, + wb_data, 2); + + /* tx control */ + val = 0xc0; + if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) + val |= 0x800000; + wb_data[0] = val; + wb_data[1] = 0; + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_CONTROL, + wb_data, 2); + + /* mac control */ + val = 0x3; + if (is_lb) { + val |= 0x4; + DP(NETIF_MSG_LINK, "enable bmac loopback\n"); + } + wb_data[0] = val; + wb_data[1] = 0; + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, + wb_data, 2); + + /* set rx mtu */ + wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; + wb_data[1] = 0; + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE, + wb_data, 2); + + /* rx control set to don't strip crc */ + val = 0x14; + if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX) + val |= 0x20; + wb_data[0] = val; + wb_data[1] = 0; + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_CONTROL, + wb_data, 2); + + /* set tx mtu */ + wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; + wb_data[1] = 0; + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE, + wb_data, 2); + + /* set cnt max size */ + wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; + wb_data[1] = 0; + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE, + wb_data, 2); + + /* configure safc */ + wb_data[0] = 0x1000200; + wb_data[1] = 0; + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_LLFC_MSG_FLDS, + wb_data, 2); + /* fix for emulation */ + if (CHIP_REV_IS_EMUL(bp)) { + wb_data[0] = 0xf000; + wb_data[1] = 0; + REG_WR_DMAE(bp, + bmac_addr + BIGMAC_REGISTER_TX_PAUSE_THRESHOLD, + wb_data, 2); + } + + REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0x1); + REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 0x0); + REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 0x0); + val = 0; + if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) + val = 1; + REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, val); + REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x0); + REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x0); + REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, 0x0); + REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x1); + REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x1); + + vars->mac_type = MAC_TYPE_BMAC; + return 0; +} + +static void bnx2x_phy_deassert(struct link_params *params, u8 phy_flags) +{ + struct bnx2x *bp = params->bp; + u32 val; + + if (phy_flags & PHY_XGXS_FLAG) { + DP(NETIF_MSG_LINK, "bnx2x_phy_deassert:XGXS\n"); + val = XGXS_RESET_BITS; + + } else { /* SerDes */ + DP(NETIF_MSG_LINK, "bnx2x_phy_deassert:SerDes\n"); + val = SERDES_RESET_BITS; + } + + val = val << (params->port*16); + + /* reset and unreset the SerDes/XGXS */ + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, + val); + udelay(500); + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, + val); + bnx2x_set_phy_mdio(params, phy_flags); +} + +void bnx2x_link_status_update(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u8 link_10g; + u8 port = params->port; + + if (params->switch_cfg == SWITCH_CFG_1G) + vars->phy_flags = PHY_SERDES_FLAG; + else + vars->phy_flags = PHY_XGXS_FLAG; + vars->link_status = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, + port_mb[port].link_status)); + + vars->link_up = (vars->link_status & LINK_STATUS_LINK_UP); + + if (vars->link_up) { + DP(NETIF_MSG_LINK, "phy link up\n"); + + vars->phy_link_up = 1; + vars->duplex = DUPLEX_FULL; + switch (vars->link_status & + LINK_STATUS_SPEED_AND_DUPLEX_MASK) { + case LINK_10THD: + vars->duplex = DUPLEX_HALF; + /* fall thru */ + case LINK_10TFD: + vars->line_speed = SPEED_10; + break; + + case LINK_100TXHD: + vars->duplex = DUPLEX_HALF; + /* fall thru */ + case LINK_100T4: + case LINK_100TXFD: + vars->line_speed = SPEED_100; + break; + + case LINK_1000THD: + vars->duplex = DUPLEX_HALF; + /* fall thru */ + case LINK_1000TFD: + vars->line_speed = SPEED_1000; + break; + + case LINK_2500THD: + vars->duplex = DUPLEX_HALF; + /* fall thru */ + case LINK_2500TFD: + vars->line_speed = SPEED_2500; + break; + + case LINK_10GTFD: + vars->line_speed = SPEED_10000; + break; + + case LINK_12GTFD: + vars->line_speed = SPEED_12000; + break; + + case LINK_12_5GTFD: + vars->line_speed = SPEED_12500; + break; + + case LINK_13GTFD: + vars->line_speed = SPEED_13000; + break; + + case LINK_15GTFD: + vars->line_speed = SPEED_15000; + break; + + case LINK_16GTFD: + vars->line_speed = SPEED_16000; + break; + + default: + break; + } + + if (vars->link_status & LINK_STATUS_TX_FLOW_CONTROL_ENABLED) + vars->flow_ctrl |= BNX2X_FLOW_CTRL_TX; + else + vars->flow_ctrl &= ~BNX2X_FLOW_CTRL_TX; + + if (vars->link_status & LINK_STATUS_RX_FLOW_CONTROL_ENABLED) + vars->flow_ctrl |= BNX2X_FLOW_CTRL_RX; + else + vars->flow_ctrl &= ~BNX2X_FLOW_CTRL_RX; + + if (vars->phy_flags & PHY_XGXS_FLAG) { + if (vars->line_speed && + ((vars->line_speed == SPEED_10) || + (vars->line_speed == SPEED_100))) { + vars->phy_flags |= PHY_SGMII_FLAG; + } else { + vars->phy_flags &= ~PHY_SGMII_FLAG; + } + } + + /* anything 10 and over uses the bmac */ + link_10g = ((vars->line_speed == SPEED_10000) || + (vars->line_speed == SPEED_12000) || + (vars->line_speed == SPEED_12500) || + (vars->line_speed == SPEED_13000) || + (vars->line_speed == SPEED_15000) || + (vars->line_speed == SPEED_16000)); + if (link_10g) + vars->mac_type = MAC_TYPE_BMAC; + else + vars->mac_type = MAC_TYPE_EMAC; + + } else { /* link down */ + DP(NETIF_MSG_LINK, "phy link down\n"); + + vars->phy_link_up = 0; + + vars->line_speed = 0; + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; + + /* indicate no mac active */ + vars->mac_type = MAC_TYPE_NONE; + } + + DP(NETIF_MSG_LINK, "link_status 0x%x phy_link_up %x\n", + vars->link_status, vars->phy_link_up); + DP(NETIF_MSG_LINK, "line_speed %x duplex %x flow_ctrl 0x%x\n", + vars->line_speed, vars->duplex, vars->flow_ctrl); +} + +static void bnx2x_update_mng(struct link_params *params, u32 link_status) +{ + struct bnx2x *bp = params->bp; + + REG_WR(bp, params->shmem_base + + offsetof(struct shmem_region, + port_mb[params->port].link_status), + link_status); +} + +static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port) +{ + u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM : + NIG_REG_INGRESS_BMAC0_MEM; + u32 wb_data[2]; + u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4); + + /* Only if the bmac is out of reset */ + if (REG_RD(bp, MISC_REG_RESET_REG_2) & + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port) && + nig_bmac_enable) { + + /* Clear Rx Enable bit in BMAC_CONTROL register */ + REG_RD_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, + wb_data, 2); + wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE; + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, + wb_data, 2); + + msleep(1); + } +} + +static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, + u32 line_speed) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u32 init_crd, crd; + u32 count = 1000; + + /* disable port */ + REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1); + + /* wait for init credit */ + init_crd = REG_RD(bp, PBF_REG_P0_INIT_CRD + port*4); + crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8); + DP(NETIF_MSG_LINK, "init_crd 0x%x crd 0x%x\n", init_crd, crd); + + while ((init_crd != crd) && count) { + msleep(5); + + crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8); + count--; + } + crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8); + if (init_crd != crd) { + DP(NETIF_MSG_LINK, "BUG! init_crd 0x%x != crd 0x%x\n", + init_crd, crd); + return -EINVAL; + } + + if (flow_ctrl & BNX2X_FLOW_CTRL_RX || + line_speed == SPEED_10 || + line_speed == SPEED_100 || + line_speed == SPEED_1000 || + line_speed == SPEED_2500) { + REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1); + /* update threshold */ + REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0); + /* update init credit */ + init_crd = 778; /* (800-18-4) */ + + } else { + u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE + + ETH_OVREHEAD)/16; + REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0); + /* update threshold */ + REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh); + /* update init credit */ + switch (line_speed) { + case SPEED_10000: + init_crd = thresh + 553 - 22; + break; + + case SPEED_12000: + init_crd = thresh + 664 - 22; + break; + + case SPEED_13000: + init_crd = thresh + 742 - 22; + break; + + case SPEED_16000: + init_crd = thresh + 778 - 22; + break; + default: + DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", + line_speed); + return -EINVAL; + } + } + REG_WR(bp, PBF_REG_P0_INIT_CRD + port*4, init_crd); + DP(NETIF_MSG_LINK, "PBF updated to speed %d credit %d\n", + line_speed, init_crd); + + /* probe the credit changes */ + REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x1); + msleep(5); + REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x0); + + /* enable port */ + REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x0); + return 0; +} + +static u32 bnx2x_get_emac_base(struct bnx2x *bp, u32 ext_phy_type, u8 port) +{ + u32 emac_base; + + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: + /* All MDC/MDIO is directed through single EMAC */ + if (REG_RD(bp, NIG_REG_PORT_SWAP)) + emac_base = GRCBASE_EMAC0; + else + emac_base = GRCBASE_EMAC1; + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: + emac_base = (port) ? GRCBASE_EMAC0 : GRCBASE_EMAC1; + break; + default: + emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0; + break; + } + return emac_base; + +} + +u8 bnx2x_cl45_write(struct bnx2x *bp, u8 port, u32 ext_phy_type, + u8 phy_addr, u8 devad, u16 reg, u16 val) +{ + u32 tmp, saved_mode; + u8 i, rc = 0; + u32 mdio_ctrl = bnx2x_get_emac_base(bp, ext_phy_type, port); + + /* set clause 45 mode, slow down the MDIO clock to 2.5MHz + * (a value of 49==0x31) and make sure that the AUTO poll is off + */ + + saved_mode = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE); + tmp = saved_mode & ~(EMAC_MDIO_MODE_AUTO_POLL | + EMAC_MDIO_MODE_CLOCK_CNT); + tmp |= (EMAC_MDIO_MODE_CLAUSE_45 | + (49 << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT)); + REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, tmp); + REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE); + udelay(40); + + /* address */ + + tmp = ((phy_addr << 21) | (devad << 16) | reg | + EMAC_MDIO_COMM_COMMAND_ADDRESS | + EMAC_MDIO_COMM_START_BUSY); + REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp); + + for (i = 0; i < 50; i++) { + udelay(10); + + tmp = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM); + if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) { + udelay(5); + break; + } + } + if (tmp & EMAC_MDIO_COMM_START_BUSY) { + DP(NETIF_MSG_LINK, "write phy register failed\n"); + rc = -EFAULT; + } else { + /* data */ + tmp = ((phy_addr << 21) | (devad << 16) | val | + EMAC_MDIO_COMM_COMMAND_WRITE_45 | + EMAC_MDIO_COMM_START_BUSY); + REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp); + + for (i = 0; i < 50; i++) { + udelay(10); + + tmp = REG_RD(bp, mdio_ctrl + + EMAC_REG_EMAC_MDIO_COMM); + if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) { + udelay(5); + break; + } + } + if (tmp & EMAC_MDIO_COMM_START_BUSY) { + DP(NETIF_MSG_LINK, "write phy register failed\n"); + rc = -EFAULT; + } + } + + /* Restore the saved mode */ + REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, saved_mode); + + return rc; +} + +u8 bnx2x_cl45_read(struct bnx2x *bp, u8 port, u32 ext_phy_type, + u8 phy_addr, u8 devad, u16 reg, u16 *ret_val) +{ + u32 val, saved_mode; + u16 i; + u8 rc = 0; + + u32 mdio_ctrl = bnx2x_get_emac_base(bp, ext_phy_type, port); + /* set clause 45 mode, slow down the MDIO clock to 2.5MHz + * (a value of 49==0x31) and make sure that the AUTO poll is off + */ + + saved_mode = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE); + val = saved_mode & ((EMAC_MDIO_MODE_AUTO_POLL | + EMAC_MDIO_MODE_CLOCK_CNT)); + val |= (EMAC_MDIO_MODE_CLAUSE_45 | + (49L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT)); + REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, val); + REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE); + udelay(40); + + /* address */ + val = ((phy_addr << 21) | (devad << 16) | reg | + EMAC_MDIO_COMM_COMMAND_ADDRESS | + EMAC_MDIO_COMM_START_BUSY); + REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val); + + for (i = 0; i < 50; i++) { + udelay(10); + + val = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM); + if (!(val & EMAC_MDIO_COMM_START_BUSY)) { + udelay(5); + break; + } + } + if (val & EMAC_MDIO_COMM_START_BUSY) { + DP(NETIF_MSG_LINK, "read phy register failed\n"); + + *ret_val = 0; + rc = -EFAULT; + + } else { + /* data */ + val = ((phy_addr << 21) | (devad << 16) | + EMAC_MDIO_COMM_COMMAND_READ_45 | + EMAC_MDIO_COMM_START_BUSY); + REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val); + + for (i = 0; i < 50; i++) { + udelay(10); + + val = REG_RD(bp, mdio_ctrl + + EMAC_REG_EMAC_MDIO_COMM); + if (!(val & EMAC_MDIO_COMM_START_BUSY)) { + *ret_val = (u16)(val & EMAC_MDIO_COMM_DATA); + break; + } + } + if (val & EMAC_MDIO_COMM_START_BUSY) { + DP(NETIF_MSG_LINK, "read phy register failed\n"); + + *ret_val = 0; + rc = -EFAULT; + } + } + + /* Restore the saved mode */ + REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, saved_mode); + + return rc; +} + +static void bnx2x_set_aer_mmd(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u32 ser_lane; + u16 offset; + + ser_lane = ((params->lane_config & + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); + + offset = (vars->phy_flags & PHY_XGXS_FLAG) ? + (params->phy_addr + ser_lane) : 0; + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_AER_BLOCK, + MDIO_AER_BLOCK_AER_REG, 0x3800 + offset); +} + +static void bnx2x_set_master_ln(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u16 new_master_ln, ser_lane; + ser_lane = ((params->lane_config & + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); + + /* set the master_ln for AN */ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_TEST_MODE_LANE, + &new_master_ln); + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_XGXS_BLOCK2 , + MDIO_XGXS_BLOCK2_TEST_MODE_LANE, + (new_master_ln | ser_lane)); +} + +static u8 bnx2x_reset_unicore(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u16 mii_control; + u16 i; + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control); + + /* reset the unicore */ + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + (mii_control | + MDIO_COMBO_IEEO_MII_CONTROL_RESET)); + if (params->switch_cfg == SWITCH_CFG_1G) + bnx2x_set_serdes_access(params); + + /* wait for the reset to self clear */ + for (i = 0; i < MDIO_ACCESS_TIMEOUT; i++) { + udelay(5); + + /* the reset erased the previous bank value */ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + &mii_control); + + if (!(mii_control & MDIO_COMBO_IEEO_MII_CONTROL_RESET)) { + udelay(5); + return 0; + } + } + + DP(NETIF_MSG_LINK, "BUG! XGXS is still in reset!\n"); + return -EINVAL; + +} + +static void bnx2x_set_swap_lanes(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + /* Each two bits represents a lane number: + No swap is 0123 => 0x1b no need to enable the swap */ + u16 ser_lane, rx_lane_swap, tx_lane_swap; + + ser_lane = ((params->lane_config & + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); + rx_lane_swap = ((params->lane_config & + PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT); + tx_lane_swap = ((params->lane_config & + PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT); + + if (rx_lane_swap != 0x1b) { + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_RX_LN_SWAP, + (rx_lane_swap | + MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE | + MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE)); + } else { + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0); + } + + if (tx_lane_swap != 0x1b) { + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_TX_LN_SWAP, + (tx_lane_swap | + MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE)); + } else { + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0); + } +} + +static void bnx2x_set_parallel_detection(struct link_params *params, + u8 phy_flags) +{ + struct bnx2x *bp = params->bp; + u16 control2; + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL2, + &control2); + if (params->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) + control2 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN; + else + control2 &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN; + DP(NETIF_MSG_LINK, "params->speed_cap_mask = 0x%x, control2 = 0x%x\n", + params->speed_cap_mask, control2); + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL2, + control2); + + if ((phy_flags & PHY_XGXS_FLAG) && + (params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) { + DP(NETIF_MSG_LINK, "XGXS\n"); + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_10G_PARALLEL_DETECT, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT); + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_10G_PARALLEL_DETECT, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL, + &control2); + + + control2 |= + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN; + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_10G_PARALLEL_DETECT, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL, + control2); + + /* Disable parallel detection of HiG */ + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_UNICORE_MODE_10G, + MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS | + MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS); + } +} + +static void bnx2x_set_autoneg(struct link_params *params, + struct link_vars *vars, + u8 enable_cl73) +{ + struct bnx2x *bp = params->bp; + u16 reg_val; + + /* CL37 Autoneg */ + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); + + /* CL37 Autoneg Enabled */ + if (vars->line_speed == SPEED_AUTO_NEG) + reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN; + else /* CL37 Autoneg Disabled */ + reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | + MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN); + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, reg_val); + + /* Enable/Disable Autodetection */ + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val); + reg_val &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN | + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT); + reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE; + if (vars->line_speed == SPEED_AUTO_NEG) + reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; + else + reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val); + + /* Enable TetonII and BAM autoneg */ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_BAM_NEXT_PAGE, + MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, + ®_val); + if (vars->line_speed == SPEED_AUTO_NEG) { + /* Enable BAM aneg Mode and TetonII aneg Mode */ + reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE | + MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN); + } else { + /* TetonII and BAM Autoneg Disabled */ + reg_val &= ~(MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE | + MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN); + } + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_BAM_NEXT_PAGE, + MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, + reg_val); + + if (enable_cl73) { + /* Enable Cl73 FSM status bits */ + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_USERB0, + MDIO_CL73_USERB0_CL73_UCTRL, + 0xe); + + /* Enable BAM Station Manager*/ + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_USERB0, + MDIO_CL73_USERB0_CL73_BAM_CTRL1, + MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN | + MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN | + MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN); + + /* Advertise CL73 link speeds */ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV2, + ®_val); + if (params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) + reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4; + if (params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) + reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX; + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV2, + reg_val); + + /* CL73 Autoneg Enabled */ + reg_val = MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN; + + } else /* CL73 Autoneg Disabled */ + reg_val = 0; + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val); +} + +/* program SerDes, forced speed */ +static void bnx2x_program_serdes(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u16 reg_val; + + /* program duplex, disable autoneg and sgmii*/ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); + reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX | + MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | + MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK); + if (params->req_duplex == DUPLEX_FULL) + reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX; + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, reg_val); + + /* program speed + - needed only if the speed is greater than 1G (2.5G or 10G) */ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_MISC1, ®_val); + /* clearing the speed value before setting the right speed */ + DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val); + + reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK | + MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); + + if (!((vars->line_speed == SPEED_1000) || + (vars->line_speed == SPEED_100) || + (vars->line_speed == SPEED_10))) { + + reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M | + MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); + if (vars->line_speed == SPEED_10000) + reg_val |= + MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4; + if (vars->line_speed == SPEED_13000) + reg_val |= + MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G; + } + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_MISC1, reg_val); + +} + +static void bnx2x_set_brcm_cl37_advertisment(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u16 val = 0; + + /* configure the 48 bits for BAM AN */ + + /* set extended capabilities */ + if (params->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) + val |= MDIO_OVER_1G_UP1_2_5G; + if (params->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) + val |= MDIO_OVER_1G_UP1_10G; + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_OVER_1G, + MDIO_OVER_1G_UP1, val); + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_OVER_1G, + MDIO_OVER_1G_UP3, 0x400); +} + +static void bnx2x_calc_ieee_aneg_adv(struct link_params *params, u16 *ieee_fc) +{ + struct bnx2x *bp = params->bp; + *ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX; + /* resolve pause mode and advertisement + * Please refer to Table 28B-3 of the 802.3ab-1999 spec */ + + switch (params->req_flow_ctrl) { + case BNX2X_FLOW_CTRL_AUTO: + if (params->req_fc_auto_adv == BNX2X_FLOW_CTRL_BOTH) { + *ieee_fc |= + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + } else { + *ieee_fc |= + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; + } + break; + case BNX2X_FLOW_CTRL_TX: + *ieee_fc |= + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; + break; + + case BNX2X_FLOW_CTRL_RX: + case BNX2X_FLOW_CTRL_BOTH: + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + break; + + case BNX2X_FLOW_CTRL_NONE: + default: + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; + break; + } + DP(NETIF_MSG_LINK, "ieee_fc = 0x%x\n", *ieee_fc); +} + +static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params, + u16 ieee_fc) +{ + struct bnx2x *bp = params->bp; + u16 val; + /* for AN, we are always publishing full duplex */ + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_AUTO_NEG_ADV, ieee_fc); + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV1, &val); + val &= ~MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH; + val |= ((ieee_fc<<3) & MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK); + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV1, val); +} + +static void bnx2x_restart_autoneg(struct link_params *params, u8 enable_cl73) +{ + struct bnx2x *bp = params->bp; + u16 mii_control; + + DP(NETIF_MSG_LINK, "bnx2x_restart_autoneg\n"); + /* Enable and restart BAM/CL37 aneg */ + + if (enable_cl73) { + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, + &mii_control); + + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, + (mii_control | + MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN | + MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN)); + } else { + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + &mii_control); + DP(NETIF_MSG_LINK, + "bnx2x_restart_autoneg mii_control before = 0x%x\n", + mii_control); + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + (mii_control | + MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | + MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN)); + } +} + +static void bnx2x_initialize_sgmii_process(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u16 control1; + + /* in SGMII mode, the unicore is always slave */ + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, + &control1); + control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT; + /* set sgmii mode (and not fiber) */ + control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE | + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET | + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE); + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, + control1); + + /* if forced speed */ + if (!(vars->line_speed == SPEED_AUTO_NEG)) { + /* set speed, disable autoneg */ + u16 mii_control; + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + &mii_control); + mii_control &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | + MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK| + MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX); + + switch (vars->line_speed) { + case SPEED_100: + mii_control |= + MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100; + break; + case SPEED_1000: + mii_control |= + MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000; + break; + case SPEED_10: + /* there is nothing to set for 10M */ + break; + default: + /* invalid speed for SGMII */ + DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", + vars->line_speed); + break; + } + + /* setting the full duplex */ + if (params->req_duplex == DUPLEX_FULL) + mii_control |= + MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX; + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + mii_control); + + } else { /* AN mode */ + /* enable and restart AN */ + bnx2x_restart_autoneg(params, 0); + } +} + + +/* + * link management + */ + +static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result) +{ /* LD LP */ + switch (pause_result) { /* ASYM P ASYM P */ + case 0xb: /* 1 0 1 1 */ + vars->flow_ctrl = BNX2X_FLOW_CTRL_TX; + break; + + case 0xe: /* 1 1 1 0 */ + vars->flow_ctrl = BNX2X_FLOW_CTRL_RX; + break; + + case 0x5: /* 0 1 0 1 */ + case 0x7: /* 0 1 1 1 */ + case 0xd: /* 1 1 0 1 */ + case 0xf: /* 1 1 1 1 */ + vars->flow_ctrl = BNX2X_FLOW_CTRL_BOTH; + break; + + default: + break; + } +} + +static u8 bnx2x_ext_phy_resolve_fc(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u8 ext_phy_addr; + u16 ld_pause; /* local */ + u16 lp_pause; /* link partner */ + u16 an_complete; /* AN complete */ + u16 pause_result; + u8 ret = 0; + u32 ext_phy_type; + u8 port = params->port; + ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + /* read twice */ + + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_STATUS, &an_complete); + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_STATUS, &an_complete); + + if (an_complete & MDIO_AN_REG_STATUS_AN_COMPLETE) { + ret = 1; + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV_PAUSE, &ld_pause); + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_LP_AUTO_NEG, &lp_pause); + pause_result = (ld_pause & + MDIO_AN_REG_ADV_PAUSE_MASK) >> 8; + pause_result |= (lp_pause & + MDIO_AN_REG_ADV_PAUSE_MASK) >> 10; + DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x\n", + pause_result); + bnx2x_pause_resolve(vars, pause_result); + if (vars->flow_ctrl == BNX2X_FLOW_CTRL_NONE && + ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, &ld_pause); + + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LP, &lp_pause); + pause_result = (ld_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 5; + pause_result |= (lp_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 7; + + bnx2x_pause_resolve(vars, pause_result); + DP(NETIF_MSG_LINK, "Ext PHY CL37 pause result 0x%x\n", + pause_result); + } + } + return ret; +} + +static u8 bnx2x_direct_parallel_detect_used(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u16 pd_10g, status2_1000x; + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_STATUS2, + &status2_1000x); + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_STATUS2, + &status2_1000x); + if (status2_1000x & MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED) { + DP(NETIF_MSG_LINK, "1G parallel detect link on port %d\n", + params->port); + return 1; + } + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_10G_PARALLEL_DETECT, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS, + &pd_10g); + + if (pd_10g & MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK) { + DP(NETIF_MSG_LINK, "10G parallel detect link on port %d\n", + params->port); + return 1; + } + return 0; +} + +static void bnx2x_flow_ctrl_resolve(struct link_params *params, + struct link_vars *vars, + u32 gp_status) +{ + struct bnx2x *bp = params->bp; + u16 ld_pause; /* local driver */ + u16 lp_pause; /* link partner */ + u16 pause_result; + + vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; + + /* resolve from gp_status in case of AN complete and not sgmii */ + if ((params->req_flow_ctrl == BNX2X_FLOW_CTRL_AUTO) && + (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) && + (!(vars->phy_flags & PHY_SGMII_FLAG)) && + (XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT)) { + if (bnx2x_direct_parallel_detect_used(params)) { + vars->flow_ctrl = params->req_fc_auto_adv; + return; + } + if ((gp_status & + (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | + MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) == + (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | + MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) { + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV1, + &ld_pause); + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_LP_ADV1, + &lp_pause); + pause_result = (ld_pause & + MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK) + >> 8; + pause_result |= (lp_pause & + MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_MASK) + >> 10; + DP(NETIF_MSG_LINK, "pause_result CL73 0x%x\n", + pause_result); + } else { + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_AUTO_NEG_ADV, + &ld_pause); + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1, + &lp_pause); + pause_result = (ld_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>5; + pause_result |= (lp_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7; + DP(NETIF_MSG_LINK, "pause_result CL37 0x%x\n", + pause_result); + } + bnx2x_pause_resolve(vars, pause_result); + } else if ((params->req_flow_ctrl == BNX2X_FLOW_CTRL_AUTO) && + (bnx2x_ext_phy_resolve_fc(params, vars))) { + return; + } else { + if (params->req_flow_ctrl == BNX2X_FLOW_CTRL_AUTO) + vars->flow_ctrl = params->req_fc_auto_adv; + else + vars->flow_ctrl = params->req_flow_ctrl; + } + DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", vars->flow_ctrl); +} + +static void bnx2x_check_fallback_to_cl37(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u16 rx_status, ustat_val, cl37_fsm_recieved; + DP(NETIF_MSG_LINK, "bnx2x_check_fallback_to_cl37\n"); + /* Step 1: Make sure signal is detected */ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_RX0, + MDIO_RX0_RX_STATUS, + &rx_status); + if ((rx_status & MDIO_RX0_RX_STATUS_SIGDET) != + (MDIO_RX0_RX_STATUS_SIGDET)) { + DP(NETIF_MSG_LINK, "Signal is not detected. Restoring CL73." + "rx_status(0x80b0) = 0x%x\n", rx_status); + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN); + return; + } + /* Step 2: Check CL73 state machine */ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_USERB0, + MDIO_CL73_USERB0_CL73_USTAT1, + &ustat_val); + if ((ustat_val & + (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK | + MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) != + (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK | + MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) { + DP(NETIF_MSG_LINK, "CL73 state-machine is not stable. " + "ustat_val(0x8371) = 0x%x\n", ustat_val); + return; + } + /* Step 3: Check CL37 Message Pages received to indicate LP + supports only CL37 */ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_REMOTE_PHY, + MDIO_REMOTE_PHY_MISC_RX_STATUS, + &cl37_fsm_recieved); + if ((cl37_fsm_recieved & + (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG | + MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) != + (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG | + MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) { + DP(NETIF_MSG_LINK, "No CL37 FSM were received. " + "misc_rx_status(0x8330) = 0x%x\n", + cl37_fsm_recieved); + return; + } + /* The combined cl37/cl73 fsm state information indicating that we are + connected to a device which does not support cl73, but does support + cl37 BAM. In this case we disable cl73 and restart cl37 auto-neg */ + /* Disable CL73 */ + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, + 0); + /* Restart CL37 autoneg */ + bnx2x_restart_autoneg(params, 0); + DP(NETIF_MSG_LINK, "Disabling CL73, and restarting CL37 autoneg\n"); +} +static u8 bnx2x_link_settings_status(struct link_params *params, + struct link_vars *vars, + u32 gp_status, + u8 ext_phy_link_up) +{ + struct bnx2x *bp = params->bp; + u16 new_line_speed; + u8 rc = 0; + vars->link_status = 0; + + if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) { + DP(NETIF_MSG_LINK, "phy link up gp_status=0x%x\n", + gp_status); + + vars->phy_link_up = 1; + vars->link_status |= LINK_STATUS_LINK_UP; + + if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS) + vars->duplex = DUPLEX_FULL; + else + vars->duplex = DUPLEX_HALF; + + bnx2x_flow_ctrl_resolve(params, vars, gp_status); + + switch (gp_status & GP_STATUS_SPEED_MASK) { + case GP_STATUS_10M: + new_line_speed = SPEED_10; + if (vars->duplex == DUPLEX_FULL) + vars->link_status |= LINK_10TFD; + else + vars->link_status |= LINK_10THD; + break; + + case GP_STATUS_100M: + new_line_speed = SPEED_100; + if (vars->duplex == DUPLEX_FULL) + vars->link_status |= LINK_100TXFD; + else + vars->link_status |= LINK_100TXHD; + break; + + case GP_STATUS_1G: + case GP_STATUS_1G_KX: + new_line_speed = SPEED_1000; + if (vars->duplex == DUPLEX_FULL) + vars->link_status |= LINK_1000TFD; + else + vars->link_status |= LINK_1000THD; + break; + + case GP_STATUS_2_5G: + new_line_speed = SPEED_2500; + if (vars->duplex == DUPLEX_FULL) + vars->link_status |= LINK_2500TFD; + else + vars->link_status |= LINK_2500THD; + break; + + case GP_STATUS_5G: + case GP_STATUS_6G: + DP(NETIF_MSG_LINK, + "link speed unsupported gp_status 0x%x\n", + gp_status); + return -EINVAL; + + case GP_STATUS_10G_KX4: + case GP_STATUS_10G_HIG: + case GP_STATUS_10G_CX4: + new_line_speed = SPEED_10000; + vars->link_status |= LINK_10GTFD; + break; + + case GP_STATUS_12G_HIG: + new_line_speed = SPEED_12000; + vars->link_status |= LINK_12GTFD; + break; + + case GP_STATUS_12_5G: + new_line_speed = SPEED_12500; + vars->link_status |= LINK_12_5GTFD; + break; + + case GP_STATUS_13G: + new_line_speed = SPEED_13000; + vars->link_status |= LINK_13GTFD; + break; + + case GP_STATUS_15G: + new_line_speed = SPEED_15000; + vars->link_status |= LINK_15GTFD; + break; + + case GP_STATUS_16G: + new_line_speed = SPEED_16000; + vars->link_status |= LINK_16GTFD; + break; + + default: + DP(NETIF_MSG_LINK, + "link speed unsupported gp_status 0x%x\n", + gp_status); + return -EINVAL; + } + + /* Upon link speed change set the NIG into drain mode. + Comes to deals with possible FIFO glitch due to clk change + when speed is decreased without link down indicator */ + if (new_line_speed != vars->line_speed) { + if (XGXS_EXT_PHY_TYPE(params->ext_phy_config) != + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT && + ext_phy_link_up) { + DP(NETIF_MSG_LINK, "Internal link speed %d is" + " different than the external" + " link speed %d\n", new_line_speed, + vars->line_speed); + vars->phy_link_up = 0; + return 0; + } + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + + params->port*4, 0); + msleep(1); + } + vars->line_speed = new_line_speed; + vars->link_status |= LINK_STATUS_SERDES_LINK; + + if ((params->req_line_speed == SPEED_AUTO_NEG) && + ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) || + (XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) || + (XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706) || + (XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726))) { + vars->autoneg = AUTO_NEG_ENABLED; + + if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) { + vars->autoneg |= AUTO_NEG_COMPLETE; + vars->link_status |= + LINK_STATUS_AUTO_NEGOTIATE_COMPLETE; + } + + vars->autoneg |= AUTO_NEG_PARALLEL_DETECTION_USED; + vars->link_status |= + LINK_STATUS_PARALLEL_DETECTION_USED; + + } + if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) + vars->link_status |= + LINK_STATUS_TX_FLOW_CONTROL_ENABLED; + + if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX) + vars->link_status |= + LINK_STATUS_RX_FLOW_CONTROL_ENABLED; + + } else { /* link_down */ + DP(NETIF_MSG_LINK, "phy link down\n"); + + vars->phy_link_up = 0; + + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; + vars->autoneg = AUTO_NEG_DISABLED; + vars->mac_type = MAC_TYPE_NONE; + + if ((params->req_line_speed == SPEED_AUTO_NEG) && + ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT))) { + /* Check signal is detected */ + bnx2x_check_fallback_to_cl37(params); + } + } + + DP(NETIF_MSG_LINK, "gp_status 0x%x phy_link_up %x line_speed %x\n", + gp_status, vars->phy_link_up, vars->line_speed); + DP(NETIF_MSG_LINK, "duplex %x flow_ctrl 0x%x" + " autoneg 0x%x\n", + vars->duplex, + vars->flow_ctrl, vars->autoneg); + DP(NETIF_MSG_LINK, "link_status 0x%x\n", vars->link_status); + + return rc; +} + +static void bnx2x_set_gmii_tx_driver(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u16 lp_up2; + u16 tx_driver; + u16 bank; + + /* read precomp */ + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_OVER_1G, + MDIO_OVER_1G_LP_UP2, &lp_up2); + + /* bits [10:7] at lp_up2, positioned at [15:12] */ + lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >> + MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT) << + MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT); + + if (lp_up2 == 0) + return; + + for (bank = MDIO_REG_BANK_TX0; bank <= MDIO_REG_BANK_TX3; + bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0)) { + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + bank, + MDIO_TX0_TX_DRIVER, &tx_driver); + + /* replace tx_driver bits [15:12] */ + if (lp_up2 != + (tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK)) { + tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK; + tx_driver |= lp_up2; + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + bank, + MDIO_TX0_TX_DRIVER, tx_driver); + } + } +} + +static u8 bnx2x_emac_program(struct link_params *params, + u32 line_speed, u32 duplex) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u16 mode = 0; + + DP(NETIF_MSG_LINK, "setting link speed & duplex\n"); + bnx2x_bits_dis(bp, GRCBASE_EMAC0 + port*0x400 + + EMAC_REG_EMAC_MODE, + (EMAC_MODE_25G_MODE | + EMAC_MODE_PORT_MII_10M | + EMAC_MODE_HALF_DUPLEX)); + switch (line_speed) { + case SPEED_10: + mode |= EMAC_MODE_PORT_MII_10M; + break; + + case SPEED_100: + mode |= EMAC_MODE_PORT_MII; + break; + + case SPEED_1000: + mode |= EMAC_MODE_PORT_GMII; + break; + + case SPEED_2500: + mode |= (EMAC_MODE_25G_MODE | EMAC_MODE_PORT_GMII); + break; + + default: + /* 10G not valid for EMAC */ + DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", line_speed); + return -EINVAL; + } + + if (duplex == DUPLEX_HALF) + mode |= EMAC_MODE_HALF_DUPLEX; + bnx2x_bits_en(bp, + GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE, + mode); + + bnx2x_set_led(params, LED_MODE_OPER, line_speed); + return 0; +} + +/*****************************************************************************/ +/* External Phy section */ +/*****************************************************************************/ +void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port) +{ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); + msleep(1); + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); +} + +static void bnx2x_ext_phy_reset(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u32 ext_phy_type; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + + DP(NETIF_MSG_LINK, "Port %x: bnx2x_ext_phy_reset\n", params->port); + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + /* The PHY reset is controled by GPIO 1 + * Give it 1ms of reset pulse + */ + if (vars->phy_flags & PHY_XGXS_FLAG) { + + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: + DP(NETIF_MSG_LINK, "XGXS Direct\n"); + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: + DP(NETIF_MSG_LINK, "XGXS 8705/8706\n"); + + /* Restore normal power mode*/ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); + + /* HW reset */ + bnx2x_ext_phy_hw_reset(bp, params->port); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, 0xa040); + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: + + /* Restore normal power mode*/ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); + + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 1<<15); + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: + DP(NETIF_MSG_LINK, "XGXS 8072\n"); + + /* Unset Low Power Mode and SW reset */ + /* Restore normal power mode*/ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 1<<15); + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: + DP(NETIF_MSG_LINK, "XGXS 8073\n"); + + /* Restore normal power mode*/ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); + + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: + DP(NETIF_MSG_LINK, "XGXS SFX7101\n"); + + /* Restore normal power mode*/ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); + + /* HW reset */ + bnx2x_ext_phy_hw_reset(bp, params->port); + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481: + /* Restore normal power mode*/ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); + + /* HW reset */ + bnx2x_ext_phy_hw_reset(bp, params->port); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 1<<15); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823: + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE: + DP(NETIF_MSG_LINK, "XGXS PHY Failure detected\n"); + break; + + default: + DP(NETIF_MSG_LINK, "BAD XGXS ext_phy_config 0x%x\n", + params->ext_phy_config); + break; + } + + } else { /* SerDes */ + ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config); + switch (ext_phy_type) { + case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT: + DP(NETIF_MSG_LINK, "SerDes Direct\n"); + break; + + case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482: + DP(NETIF_MSG_LINK, "SerDes 5482\n"); + bnx2x_ext_phy_hw_reset(bp, params->port); + break; + + default: + DP(NETIF_MSG_LINK, "BAD SerDes ext_phy_config 0x%x\n", + params->ext_phy_config); + break; + } + } +} + +static void bnx2x_save_spirom_version(struct bnx2x *bp, u8 port, + u32 shmem_base, u32 spirom_ver) +{ + DP(NETIF_MSG_LINK, "FW version 0x%x:0x%x for port %d\n", + (u16)(spirom_ver>>16), (u16)spirom_ver, port); + REG_WR(bp, shmem_base + + offsetof(struct shmem_region, + port_mb[port].ext_phy_fw_version), + spirom_ver); +} + +static void bnx2x_save_bcm_spirom_ver(struct bnx2x *bp, u8 port, + u32 ext_phy_type, u8 ext_phy_addr, + u32 shmem_base) +{ + u16 fw_ver1, fw_ver2; + + bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER1, &fw_ver1); + bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, &fw_ver2); + bnx2x_save_spirom_version(bp, port, shmem_base, + (u32)(fw_ver1<<16 | fw_ver2)); +} + + +static void bnx2x_save_8481_spirom_version(struct bnx2x *bp, u8 port, + u8 ext_phy_addr, u32 shmem_base) +{ + u16 val, fw_ver1, fw_ver2, cnt; + /* For the 32 bits registers in 8481, access via MDIO2ARM interface.*/ + /* (1) set register 0xc200_0014(SPI_BRIDGE_CTRL_2) to 0x03000000 */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, MDIO_PMA_DEVAD, + 0xA819, 0x0014); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xA81A, + 0xc200); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xA81B, + 0x0000); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xA81C, + 0x0300); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xA817, + 0x0009); + + for (cnt = 0; cnt < 100; cnt++) { + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xA818, + &val); + if (val & 1) + break; + udelay(5); + } + if (cnt == 100) { + DP(NETIF_MSG_LINK, "Unable to read 8481 phy fw version(1)\n"); + bnx2x_save_spirom_version(bp, port, + shmem_base, 0); + return; + } + + + /* 2) read register 0xc200_0000 (SPI_FW_STATUS) */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, MDIO_PMA_DEVAD, + 0xA819, 0x0000); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, MDIO_PMA_DEVAD, + 0xA81A, 0xc200); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, MDIO_PMA_DEVAD, + 0xA817, 0x000A); + for (cnt = 0; cnt < 100; cnt++) { + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xA818, + &val); + if (val & 1) + break; + udelay(5); + } + if (cnt == 100) { + DP(NETIF_MSG_LINK, "Unable to read 8481 phy fw version(2)\n"); + bnx2x_save_spirom_version(bp, port, + shmem_base, 0); + return; + } + + /* lower 16 bits of the register SPI_FW_STATUS */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xA81B, + &fw_ver1); + /* upper 16 bits of register SPI_FW_STATUS */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xA81C, + &fw_ver2); + + bnx2x_save_spirom_version(bp, port, + shmem_base, (fw_ver2<<16) | fw_ver1); +} + +static void bnx2x_bcm8072_external_rom_boot(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + /* Need to wait 200ms after reset */ + msleep(200); + /* Boot port from external ROM + * Set ser_boot_ctl bit in the MISC_CTRL1 register + */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0001); + + /* Reset internal microprocessor */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); + /* set micro reset = 0 */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); + /* Reset internal microprocessor */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); + /* wait for 100ms for code download via SPI port */ + msleep(100); + + /* Clear ser_boot_ctl bit */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0000); + /* Wait 100ms */ + msleep(100); + + bnx2x_save_bcm_spirom_ver(bp, port, + ext_phy_type, + ext_phy_addr, + params->shmem_base); +} + +static u8 bnx2x_8073_is_snr_needed(struct link_params *params) +{ + /* This is only required for 8073A1, version 102 only */ + + struct bnx2x *bp = params->bp; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u16 val; + + /* Read 8073 HW revision*/ + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_CHIP_REV, &val); + + if (val != 1) { + /* No need to workaround in 8073 A1 */ + return 0; + } + + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, &val); + + /* SNR should be applied only for version 0x102 */ + if (val != 0x102) + return 0; + + return 1; +} + +static u8 bnx2x_bcm8073_xaui_wa(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u16 val, cnt, cnt1 ; + + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_CHIP_REV, &val); + + if (val > 0) { + /* No need to workaround in 8073 A1 */ + return 0; + } + /* XAUI workaround in 8073 A0: */ + + /* After loading the boot ROM and restarting Autoneg, + poll Dev1, Reg $C820: */ + + for (cnt = 0; cnt < 1000; cnt++) { + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_SPEED_LINK_STATUS, + &val); + /* If bit [14] = 0 or bit [13] = 0, continue on with + system initialization (XAUI work-around not required, + as these bits indicate 2.5G or 1G link up). */ + if (!(val & (1<<14)) || !(val & (1<<13))) { + DP(NETIF_MSG_LINK, "XAUI work-around not required\n"); + return 0; + } else if (!(val & (1<<15))) { + DP(NETIF_MSG_LINK, "clc bit 15 went off\n"); + /* If bit 15 is 0, then poll Dev1, Reg $C841 until + it's MSB (bit 15) goes to 1 (indicating that the + XAUI workaround has completed), + then continue on with system initialization.*/ + for (cnt1 = 0; cnt1 < 1000; cnt1++) { + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_XAUI_WA, &val); + if (val & (1<<15)) { + DP(NETIF_MSG_LINK, + "XAUI workaround has completed\n"); + return 0; + } + msleep(3); + } + break; + } + msleep(3); + } + DP(NETIF_MSG_LINK, "Warning: XAUI work-around timeout !!!\n"); + return -EINVAL; +} + +static void bnx2x_bcm8073_bcm8727_external_rom_boot(struct bnx2x *bp, u8 port, + u8 ext_phy_addr, + u32 ext_phy_type, + u32 shmem_base) +{ + /* Boot port from external ROM */ + /* EDC grst */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + 0x0001); + + /* ucode reboot and rst */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + 0x008c); + + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0001); + + /* Reset internal microprocessor */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); + + /* Release srst bit */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); + + /* wait for 100ms for code download via SPI port */ + msleep(100); + + /* Clear ser_boot_ctl bit */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0000); + + bnx2x_save_bcm_spirom_ver(bp, port, + ext_phy_type, + ext_phy_addr, + shmem_base); +} + +static void bnx2x_bcm8073_external_rom_boot(struct bnx2x *bp, u8 port, + u8 ext_phy_addr, + u32 shmem_base) +{ + bnx2x_bcm8073_bcm8727_external_rom_boot(bp, port, ext_phy_addr, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + shmem_base); +} + +static void bnx2x_bcm8727_external_rom_boot(struct bnx2x *bp, u8 port, + u8 ext_phy_addr, + u32 shmem_base) +{ + bnx2x_bcm8073_bcm8727_external_rom_boot(bp, port, ext_phy_addr, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + shmem_base); + +} + +static void bnx2x_bcm8726_external_rom_boot(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + /* Need to wait 100ms after reset */ + msleep(100); + + /* Micro controller re-boot */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + 0x018B); + + /* Set soft reset */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); + + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0001); + + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); + + /* wait for 150ms for microcode load */ + msleep(150); + + /* Disable serial boot control, tristates pins SS_N, SCK, MOSI, MISO */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0000); + + msleep(200); + bnx2x_save_bcm_spirom_ver(bp, port, + ext_phy_type, + ext_phy_addr, + params->shmem_base); +} + +static void bnx2x_sfp_set_transmitter(struct bnx2x *bp, u8 port, + u32 ext_phy_type, u8 ext_phy_addr, + u8 tx_en) +{ + u16 val; + + DP(NETIF_MSG_LINK, "Setting transmitter tx_en=%x for port %x\n", + tx_en, port); + /* Disable/Enable transmitter ( TX laser of the SFP+ module.)*/ + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + &val); + + if (tx_en) + val &= ~(1<<15); + else + val |= (1<<15); + + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + val); +} + +static u8 bnx2x_8726_read_sfp_module_eeprom(struct link_params *params, + u16 addr, u8 byte_cnt, u8 *o_buf) +{ + struct bnx2x *bp = params->bp; + u16 val = 0; + u16 i; + u8 port = params->port; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + if (byte_cnt > 16) { + DP(NETIF_MSG_LINK, "Reading from eeprom is" + " is limited to 0xf\n"); + return -EINVAL; + } + /* Set the read command byte count */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT, + (byte_cnt | 0xa000)); + + /* Set the read command address */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR, + addr); + + /* Activate read command */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, + 0x2c0f); + + /* Wait up to 500us for command complete status */ + for (i = 0; i < 100; i++) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); + if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == + MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) + break; + udelay(5); + } + + if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) != + MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) { + DP(NETIF_MSG_LINK, + "Got bad status 0x%x when reading from SFP+ EEPROM\n", + (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK)); + return -EINVAL; + } + + /* Read the buffer */ + for (i = 0; i < byte_cnt; i++) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF + i, &val); + o_buf[i] = (u8)(val & MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK); + } + + for (i = 0; i < 100; i++) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); + if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == + MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE) + return 0;; + msleep(1); + } + return -EINVAL; +} + +static u8 bnx2x_8727_read_sfp_module_eeprom(struct link_params *params, + u16 addr, u8 byte_cnt, u8 *o_buf) +{ + struct bnx2x *bp = params->bp; + u16 val, i; + u8 port = params->port; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + if (byte_cnt > 16) { + DP(NETIF_MSG_LINK, "Reading from eeprom is" + " is limited to 0xf\n"); + return -EINVAL; + } + + /* Need to read from 1.8000 to clear it */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, + &val); + + /* Set the read command byte count */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT, + ((byte_cnt < 2) ? 2 : byte_cnt)); + + /* Set the read command address */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR, + addr); + /* Set the destination address */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0x8004, + MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF); + + /* Activate read command */ + bnx2x_cl45_write(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, + 0x8002); + /* Wait appropriate time for two-wire command to finish before + polling the status register */ + msleep(1); + + /* Wait up to 500us for command complete status */ + for (i = 0; i < 100; i++) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); + if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == + MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) + break; + udelay(5); + } + + if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) != + MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) { + DP(NETIF_MSG_LINK, + "Got bad status 0x%x when reading from SFP+ EEPROM\n", + (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK)); + return -EINVAL; + } + + /* Read the buffer */ + for (i = 0; i < byte_cnt; i++) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF + i, &val); + o_buf[i] = (u8)(val & MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK); + } + + for (i = 0; i < 100; i++) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); + if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == + MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE) + return 0;; + msleep(1); + } + + return -EINVAL; +} + +u8 bnx2x_read_sfp_module_eeprom(struct link_params *params, u16 addr, + u8 byte_cnt, u8 *o_buf) +{ + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) + return bnx2x_8726_read_sfp_module_eeprom(params, addr, + byte_cnt, o_buf); + else if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) + return bnx2x_8727_read_sfp_module_eeprom(params, addr, + byte_cnt, o_buf); + return -EINVAL; +} + +static u8 bnx2x_get_edc_mode(struct link_params *params, + u16 *edc_mode) +{ + struct bnx2x *bp = params->bp; + u8 val, check_limiting_mode = 0; + *edc_mode = EDC_MODE_LIMITING; + + /* First check for copper cable */ + if (bnx2x_read_sfp_module_eeprom(params, + SFP_EEPROM_CON_TYPE_ADDR, + 1, + &val) != 0) { + DP(NETIF_MSG_LINK, "Failed to read from SFP+ module EEPROM\n"); + return -EINVAL; + } + + switch (val) { + case SFP_EEPROM_CON_TYPE_VAL_COPPER: + { + u8 copper_module_type; + + /* Check if its active cable( includes SFP+ module) + of passive cable*/ + if (bnx2x_read_sfp_module_eeprom(params, + SFP_EEPROM_FC_TX_TECH_ADDR, + 1, + &copper_module_type) != + 0) { + DP(NETIF_MSG_LINK, + "Failed to read copper-cable-type" + " from SFP+ EEPROM\n"); + return -EINVAL; + } + + if (copper_module_type & + SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE) { + DP(NETIF_MSG_LINK, "Active Copper cable detected\n"); + check_limiting_mode = 1; + } else if (copper_module_type & + SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE) { + DP(NETIF_MSG_LINK, "Passive Copper" + " cable detected\n"); + *edc_mode = + EDC_MODE_PASSIVE_DAC; + } else { + DP(NETIF_MSG_LINK, "Unknown copper-cable-" + "type 0x%x !!!\n", copper_module_type); + return -EINVAL; + } + break; + } + case SFP_EEPROM_CON_TYPE_VAL_LC: + DP(NETIF_MSG_LINK, "Optic module detected\n"); + check_limiting_mode = 1; + break; + default: + DP(NETIF_MSG_LINK, "Unable to determine module type 0x%x !!!\n", + val); + return -EINVAL; + } + + if (check_limiting_mode) { + u8 options[SFP_EEPROM_OPTIONS_SIZE]; + if (bnx2x_read_sfp_module_eeprom(params, + SFP_EEPROM_OPTIONS_ADDR, + SFP_EEPROM_OPTIONS_SIZE, + options) != 0) { + DP(NETIF_MSG_LINK, "Failed to read Option" + " field from module EEPROM\n"); + return -EINVAL; + } + if ((options[0] & SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK)) + *edc_mode = EDC_MODE_LINEAR; + else + *edc_mode = EDC_MODE_LIMITING; + } + DP(NETIF_MSG_LINK, "EDC mode is set to 0x%x\n", *edc_mode); + return 0; +} + +/* This function read the relevant field from the module ( SFP+ ), + and verify it is compliant with this board */ +static u8 bnx2x_verify_sfp_module(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u32 val; + u32 fw_resp; + char vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE+1]; + char vendor_pn[SFP_EEPROM_PART_NO_SIZE+1]; + + val = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, dev_info. + port_feature_config[params->port].config)); + if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == + PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_NO_ENFORCEMENT) { + DP(NETIF_MSG_LINK, "NOT enforcing module verification\n"); + return 0; + } + + /* Ask the FW to validate the module */ + if (!(params->feature_config_flags & + FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY)) { + DP(NETIF_MSG_LINK, "FW does not support OPT MDL " + "verification\n"); + return -EINVAL; + } + + fw_resp = bnx2x_fw_command(bp, DRV_MSG_CODE_VRFY_OPT_MDL); + if (fw_resp == FW_MSG_CODE_VRFY_OPT_MDL_SUCCESS) { + DP(NETIF_MSG_LINK, "Approved module\n"); + return 0; + } + + /* format the warning message */ + if (bnx2x_read_sfp_module_eeprom(params, + SFP_EEPROM_VENDOR_NAME_ADDR, + SFP_EEPROM_VENDOR_NAME_SIZE, + (u8 *)vendor_name)) + vendor_name[0] = '\0'; + else + vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE] = '\0'; + if (bnx2x_read_sfp_module_eeprom(params, + SFP_EEPROM_PART_NO_ADDR, + SFP_EEPROM_PART_NO_SIZE, + (u8 *)vendor_pn)) + vendor_pn[0] = '\0'; + else + vendor_pn[SFP_EEPROM_PART_NO_SIZE] = '\0'; + + netdev_info(bp->dev, "Warning: Unqualified SFP+ module detected, Port %d from %s part number %s\n", + params->port, vendor_name, vendor_pn); + return -EINVAL; +} + +static u8 bnx2x_bcm8726_set_limiting_mode(struct link_params *params, + u16 edc_mode) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u16 cur_limiting_mode; + + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, + &cur_limiting_mode); + DP(NETIF_MSG_LINK, "Current Limiting mode is 0x%x\n", + cur_limiting_mode); + + if (edc_mode == EDC_MODE_LIMITING) { + DP(NETIF_MSG_LINK, + "Setting LIMITING MODE\n"); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, + EDC_MODE_LIMITING); + } else { /* LRM mode ( default )*/ + + DP(NETIF_MSG_LINK, "Setting LRM MODE\n"); + + /* Changing to LRM mode takes quite few seconds. + So do it only if current mode is limiting + ( default is LRM )*/ + if (cur_limiting_mode != EDC_MODE_LIMITING) + return 0; + + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LRM_MODE, + 0); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, + 0x128); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL0, + 0x4008); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LRM_MODE, + 0xaaaa); + } + return 0; +} + +static u8 bnx2x_bcm8727_set_limiting_mode(struct link_params *params, + u16 edc_mode) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u16 phy_identifier; + u16 rom_ver2_val; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + &phy_identifier); + + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + (phy_identifier & ~(1<<9))); + + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, + &rom_ver2_val); + /* Keep the MSB 8-bits, and set the LSB 8-bits with the edc_mode */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, + (rom_ver2_val & 0xff00) | (edc_mode & 0x00ff)); + + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + (phy_identifier | (1<<9))); + + return 0; +} + + +static u8 bnx2x_wait_for_sfp_module_initialized(struct link_params *params) +{ + u8 val; + struct bnx2x *bp = params->bp; + u16 timeout; + /* Initialization time after hot-plug may take up to 300ms for some + phys type ( e.g. JDSU ) */ + for (timeout = 0; timeout < 60; timeout++) { + if (bnx2x_read_sfp_module_eeprom(params, 1, 1, &val) + == 0) { + DP(NETIF_MSG_LINK, "SFP+ module initialization " + "took %d ms\n", timeout * 5); + return 0; + } + msleep(5); + } + return -EINVAL; +} + +static void bnx2x_8727_power_module(struct bnx2x *bp, + struct link_params *params, + u8 ext_phy_addr, u8 is_power_up) { + /* Make sure GPIOs are not using for LED mode */ + u16 val; + u8 port = params->port; + /* + * In the GPIO register, bit 4 is use to detemine if the GPIOs are + * operating as INPUT or as OUTPUT. Bit 1 is for input, and 0 for + * output + * Bits 0-1 determine the gpios value for OUTPUT in case bit 4 val is 0 + * Bits 8-9 determine the gpios value for INPUT in case bit 4 val is 1 + * where the 1st bit is the over-current(only input), and 2nd bit is + * for power( only output ) + */ + + /* + * In case of NOC feature is disabled and power is up, set GPIO control + * as input to enable listening of over-current indication + */ + + if (!(params->feature_config_flags & + FEATURE_CONFIG_BCM8727_NOC) && is_power_up) + val = (1<<4); + else + /* + * Set GPIO control to OUTPUT, and set the power bit + * to according to the is_power_up + */ + val = ((!(is_power_up)) << 1); + + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_GPIO_CTRL, + val); +} + +static u8 bnx2x_sfp_module_detection(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u16 edc_mode; + u8 rc = 0; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + u32 val = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, dev_info. + port_feature_config[params->port].config)); + + DP(NETIF_MSG_LINK, "SFP+ module plugged in/out detected on port %d\n", + params->port); + + if (bnx2x_get_edc_mode(params, &edc_mode) != 0) { + DP(NETIF_MSG_LINK, "Failed to get valid module type\n"); + return -EINVAL; + } else if (bnx2x_verify_sfp_module(params) != + 0) { + /* check SFP+ module compatibility */ + DP(NETIF_MSG_LINK, "Module verification failed!!\n"); + rc = -EINVAL; + /* Turn on fault module-detected led */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, + MISC_REGISTERS_GPIO_HIGH, + params->port); + if ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) && + ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == + PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_POWER_DOWN)) { + /* Shutdown SFP+ module */ + DP(NETIF_MSG_LINK, "Shutdown SFP+ module!!\n"); + bnx2x_8727_power_module(bp, params, + ext_phy_addr, 0); + return rc; + } + } else { + /* Turn off fault module-detected led */ + DP(NETIF_MSG_LINK, "Turn off fault module-detected led\n"); + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, + MISC_REGISTERS_GPIO_LOW, + params->port); + } + + /* power up the SFP module */ + if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) + bnx2x_8727_power_module(bp, params, ext_phy_addr, 1); + + /* Check and set limiting mode / LRM mode on 8726. + On 8727 it is done automatically */ + if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) + bnx2x_bcm8726_set_limiting_mode(params, edc_mode); + else + bnx2x_bcm8727_set_limiting_mode(params, edc_mode); + /* + * Enable transmit for this module if the module is approved, or + * if unapproved modules should also enable the Tx laser + */ + if (rc == 0 || + (val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) != + PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER) + bnx2x_sfp_set_transmitter(bp, params->port, + ext_phy_type, ext_phy_addr, 1); + else + bnx2x_sfp_set_transmitter(bp, params->port, + ext_phy_type, ext_phy_addr, 0); + + return rc; +} + +void bnx2x_handle_module_detect_int(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u32 gpio_val; + u8 port = params->port; + + /* Set valid module led off */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, + MISC_REGISTERS_GPIO_HIGH, + params->port); + + /* Get current gpio val refelecting module plugged in / out*/ + gpio_val = bnx2x_get_gpio(bp, MISC_REGISTERS_GPIO_3, port); + + /* Call the handling function in case module is detected */ + if (gpio_val == 0) { + + bnx2x_set_gpio_int(bp, MISC_REGISTERS_GPIO_3, + MISC_REGISTERS_GPIO_INT_OUTPUT_CLR, + port); + + if (bnx2x_wait_for_sfp_module_initialized(params) == + 0) + bnx2x_sfp_module_detection(params); + else + DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n"); + } else { + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + + u32 ext_phy_type = + XGXS_EXT_PHY_TYPE(params->ext_phy_config); + u32 val = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, dev_info. + port_feature_config[params->port]. + config)); + + bnx2x_set_gpio_int(bp, MISC_REGISTERS_GPIO_3, + MISC_REGISTERS_GPIO_INT_OUTPUT_SET, + port); + /* Module was plugged out. */ + /* Disable transmit for this module */ + if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == + PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER) + bnx2x_sfp_set_transmitter(bp, params->port, + ext_phy_type, ext_phy_addr, 0); + } +} + +static void bnx2x_bcm807x_force_10G(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + /* Force KR or KX */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 0x2040); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_10G_CTRL2, + 0x000b); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_BCM_CTRL, + 0x0000); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, + 0x0000); +} + +static void bnx2x_bcm8073_set_xaui_low_power_mode(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u16 val; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_CHIP_REV, &val); + + if (val == 0) { + /* Mustn't set low power mode in 8073 A0 */ + return; + } + + /* Disable PLL sequencer (use read-modify-write to clear bit 13) */ + bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, + MDIO_XS_PLL_SEQUENCER, &val); + val &= ~(1<<13); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, MDIO_XS_PLL_SEQUENCER, val); + + /* PLL controls */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x805E, 0x1077); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x805D, 0x0000); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x805C, 0x030B); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x805B, 0x1240); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x805A, 0x2490); + + /* Tx Controls */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x80A7, 0x0C74); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x80A6, 0x9041); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x80A5, 0x4640); + + /* Rx Controls */ + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x80FE, 0x01C4); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x80FD, 0x9249); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, 0x80FC, 0x2015); + + /* Enable PLL sequencer (use read-modify-write to set bit 13) */ + bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, + MDIO_XS_PLL_SEQUENCER, &val); + val |= (1<<13); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_XS_DEVAD, MDIO_XS_PLL_SEQUENCER, val); +} + +static void bnx2x_8073_set_pause_cl37(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u16 cl37_val; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, &cl37_val); + + cl37_val &= ~MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ + + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) { + cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC; + } + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { + cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; + } + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) { + cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + } + DP(NETIF_MSG_LINK, + "Ext phy AN advertize cl37 0x%x\n", cl37_val); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, cl37_val); + msleep(500); +} + +static void bnx2x_ext_phy_set_pause(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u16 val; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + /* read modify write pause advertizing */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV_PAUSE, &val); + + val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH; + + /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ + + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { + val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC; + } + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) { + val |= + MDIO_AN_REG_ADV_PAUSE_PAUSE; + } + DP(NETIF_MSG_LINK, + "Ext phy AN advertize 0x%x\n", val); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV_PAUSE, val); +} +static void bnx2x_set_preemphasis(struct link_params *params) +{ + u16 bank, i = 0; + struct bnx2x *bp = params->bp; + + for (bank = MDIO_REG_BANK_RX0, i = 0; bank <= MDIO_REG_BANK_RX3; + bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0), i++) { + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + bank, + MDIO_RX0_RX_EQ_BOOST, + params->xgxs_config_rx[i]); + } + + for (bank = MDIO_REG_BANK_TX0, i = 0; bank <= MDIO_REG_BANK_TX3; + bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0), i++) { + CL45_WR_OVER_CL22(bp, params->port, + params->phy_addr, + bank, + MDIO_TX0_TX_DRIVER, + params->xgxs_config_tx[i]); + } +} + + +static void bnx2x_8481_set_led4(struct link_params *params, + u32 ext_phy_type, u8 ext_phy_addr) +{ + struct bnx2x *bp = params->bp; + + /* PHYC_CTL_LED_CTL */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LINK_SIGNAL, 0xa482); + + /* Unmask LED4 for 10G link */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_SIGNAL_MASK, (1<<6)); + /* 'Interrupt Mask' */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + 0xFFFB, 0xFFFD); +} +static void bnx2x_8481_set_legacy_led_mode(struct link_params *params, + u32 ext_phy_type, u8 ext_phy_addr) +{ + struct bnx2x *bp = params->bp; + + /* LED1 (10G Link): Disable LED1 when 10/100/1000 link */ + /* LED2 (1G/100/10 Link): Enable LED2 when 10/100/1000 link) */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_LEGACY_SHADOW, + (1<<15) | (0xd << 10) | (0xc<<4) | 0xe); +} + +static void bnx2x_8481_set_10G_led_mode(struct link_params *params, + u32 ext_phy_type, u8 ext_phy_addr) +{ + struct bnx2x *bp = params->bp; + u16 val1; + + /* LED1 (10G Link) */ + /* Enable continuse based on source 7(10G-link) */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LINK_SIGNAL, + &val1); + /* Set bit 2 to 0, and bits [1:0] to 10 */ + val1 &= ~((1<<0) | (1<<2) | (1<<7)); /* Clear bits 0,2,7*/ + val1 |= ((1<<1) | (1<<6)); /* Set bit 1, 6 */ + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LINK_SIGNAL, + val1); + + /* Unmask LED1 for 10G link */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED1_MASK, + &val1); + /* Set bit 2 to 0, and bits [1:0] to 10 */ + val1 |= (1<<7); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED1_MASK, + val1); + + /* LED2 (1G/100/10G Link) */ + /* Mask LED2 for 10G link */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED2_MASK, + 0); + + /* Unmask LED3 for 10G link */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED3_MASK, + 0x6); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED3_BLINK, + 0); +} + + +static void bnx2x_init_internal_phy(struct link_params *params, + struct link_vars *vars, + u8 enable_cl73) +{ + struct bnx2x *bp = params->bp; + + if (!(vars->phy_flags & PHY_SGMII_FLAG)) { + if ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) && + (params->feature_config_flags & + FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) + bnx2x_set_preemphasis(params); + + /* forced speed requested? */ + if (vars->line_speed != SPEED_AUTO_NEG || + ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) && + params->loopback_mode == LOOPBACK_EXT)) { + DP(NETIF_MSG_LINK, "not SGMII, no AN\n"); + + /* disable autoneg */ + bnx2x_set_autoneg(params, vars, 0); + + /* program speed and duplex */ + bnx2x_program_serdes(params, vars); + + } else { /* AN_mode */ + DP(NETIF_MSG_LINK, "not SGMII, AN\n"); + + /* AN enabled */ + bnx2x_set_brcm_cl37_advertisment(params); + + /* program duplex & pause advertisement (for aneg) */ + bnx2x_set_ieee_aneg_advertisment(params, + vars->ieee_fc); + + /* enable autoneg */ + bnx2x_set_autoneg(params, vars, enable_cl73); + + /* enable and restart AN */ + bnx2x_restart_autoneg(params, enable_cl73); + } + + } else { /* SGMII mode */ + DP(NETIF_MSG_LINK, "SGMII\n"); + + bnx2x_initialize_sgmii_process(params, vars); + } +} + +static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u32 ext_phy_type; + u8 ext_phy_addr; + u16 cnt; + u16 ctrl = 0; + u16 val = 0; + u8 rc = 0; + + if (vars->phy_flags & PHY_XGXS_FLAG) { + ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + /* Make sure that the soft reset is off (expect for the 8072: + * due to the lock, it will be done inside the specific + * handling) + */ + if ((ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073)) { + /* Wait for soft reset to get cleared upto 1 sec */ + for (cnt = 0; cnt < 1000; cnt++) { + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, &ctrl); + if (!(ctrl & (1<<15))) + break; + msleep(1); + } + DP(NETIF_MSG_LINK, "control reg 0x%x (after %d ms)\n", + ctrl, cnt); + } + + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705: + DP(NETIF_MSG_LINK, "XGXS 8705\n"); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL, + 0x8288); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + 0x7fbf); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CMU_PLL_BYPASS, + 0x0100); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_WIS_DEVAD, + MDIO_WIS_REG_LASI_CNTL, 0x1); + + /* BCM8705 doesn't have microcode, hence the 0 */ + bnx2x_save_spirom_version(bp, params->port, + params->shmem_base, 0); + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: + /* Wait until fw is loaded */ + for (cnt = 0; cnt < 100; cnt++) { + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER1, &val); + if (val) + break; + msleep(10); + } + DP(NETIF_MSG_LINK, "XGXS 8706 is initialized " + "after %d ms\n", cnt); + if ((params->feature_config_flags & + FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) { + u8 i; + u16 reg; + for (i = 0; i < 4; i++) { + reg = MDIO_XS_8706_REG_BANK_RX0 + + i*(MDIO_XS_8706_REG_BANK_RX1 - + MDIO_XS_8706_REG_BANK_RX0); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_XS_DEVAD, + reg, &val); + /* Clear first 3 bits of the control */ + val &= ~0x7; + /* Set control bits according to + configuation */ + val |= (params->xgxs_config_rx[i] & + 0x7); + DP(NETIF_MSG_LINK, "Setting RX" + "Equalizer to BCM8706 reg 0x%x" + " <-- val 0x%x\n", reg, val); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_XS_DEVAD, + reg, val); + } + } + /* Force speed */ + if (params->req_line_speed == SPEED_10000) { + DP(NETIF_MSG_LINK, "XGXS 8706 force 10Gbps\n"); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_DIGITAL_CTRL, + 0x400); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, 1); + } else { + /* Force 1Gbps using autoneg with 1G + advertisment */ + + /* Allow CL37 through CL73 */ + DP(NETIF_MSG_LINK, "XGXS 8706 AutoNeg\n"); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_CL73, + 0x040c); + + /* Enable Full-Duplex advertisment on CL37 */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LP, + 0x0020); + /* Enable CL37 AN */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_AN, + 0x1000); + /* 1G support */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV, (1<<5)); + + /* Enable clause 73 AN */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, + 0x1200); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM_CTRL, + 0x0400); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, 0x0004); + + } + bnx2x_save_bcm_spirom_ver(bp, params->port, + ext_phy_type, + ext_phy_addr, + params->shmem_base); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: + DP(NETIF_MSG_LINK, "Initializing BCM8726\n"); + bnx2x_bcm8726_external_rom_boot(params); + + /* Need to call module detected on initialization since + the module detection triggered by actual module + insertion might occur before driver is loaded, and when + driver is loaded, it reset all registers, including the + transmitter */ + bnx2x_sfp_module_detection(params); + + /* Set Flow control */ + bnx2x_ext_phy_set_pause(params, vars); + if (params->req_line_speed == SPEED_1000) { + DP(NETIF_MSG_LINK, "Setting 1G force\n"); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, 0x40); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_10G_CTRL2, 0xD); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, 0x5); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM_CTRL, + 0x400); + } else if ((params->req_line_speed == + SPEED_AUTO_NEG) && + ((params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_1G))) { + DP(NETIF_MSG_LINK, "Setting 1G clause37\n"); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, + MDIO_AN_REG_ADV, 0x20); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_CL73, 0x040c); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, 0x0020); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_AN, 0x1000); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, 0x1200); + + /* Enable RX-ALARM control to receive + interrupt for 1G speed change */ + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, 0x4); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM_CTRL, + 0x400); + + } else { /* Default 10G. Set only LASI control */ + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, 1); + } + + /* Set TX PreEmphasis if needed */ + if ((params->feature_config_flags & + FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) { + DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x," + "TX_CTRL2 0x%x\n", + params->xgxs_config_tx[0], + params->xgxs_config_tx[1]); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8726_TX_CTRL1, + params->xgxs_config_tx[0]); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8726_TX_CTRL2, + params->xgxs_config_tx[1]); + } + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: + { + u16 tmp1; + u16 rx_alarm_ctrl_val; + u16 lasi_ctrl_val; + if (ext_phy_type == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) { + rx_alarm_ctrl_val = 0x400; + lasi_ctrl_val = 0x0004; + } else { + rx_alarm_ctrl_val = (1<<2); + lasi_ctrl_val = 0x0004; + } + + /* enable LASI */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM_CTRL, + rx_alarm_ctrl_val); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, + lasi_ctrl_val); + + bnx2x_8073_set_pause_cl37(params, vars); + + if (ext_phy_type == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) + bnx2x_bcm8072_external_rom_boot(params); + else + /* In case of 8073 with long xaui lines, + don't set the 8073 xaui low power*/ + bnx2x_bcm8073_set_xaui_low_power_mode(params); + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_M8051_MSGOUT_REG, + &tmp1); + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM, &tmp1); + + DP(NETIF_MSG_LINK, "Before rom RX_ALARM(port1):" + "0x%x\n", tmp1); + + /* If this is forced speed, set to KR or KX + * (all other are not supported) + */ + if (params->loopback_mode == LOOPBACK_EXT) { + bnx2x_bcm807x_force_10G(params); + DP(NETIF_MSG_LINK, + "Forced speed 10G on 807X\n"); + break; + } else { + bnx2x_cl45_write(bp, params->port, + ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_BCM_CTRL, + 0x0002); + } + if (params->req_line_speed != SPEED_AUTO_NEG) { + if (params->req_line_speed == SPEED_10000) { + val = (1<<7); + } else if (params->req_line_speed == + SPEED_2500) { + val = (1<<5); + /* Note that 2.5G works only + when used with 1G advertisment */ + } else + val = (1<<5); + } else { + + val = 0; + if (params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) + val |= (1<<7); + + /* Note that 2.5G works only when + used with 1G advertisment */ + if (params->speed_cap_mask & + (PORT_HW_CFG_SPEED_CAPABILITY_D0_1G | + PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)) + val |= (1<<5); + DP(NETIF_MSG_LINK, + "807x autoneg val = 0x%x\n", val); + } + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV, val); + if (ext_phy_type == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8073_2_5G, &tmp1); + + if (((params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) && + (params->req_line_speed == + SPEED_AUTO_NEG)) || + (params->req_line_speed == + SPEED_2500)) { + u16 phy_ver; + /* Allow 2.5G for A1 and above */ + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_CHIP_REV, &phy_ver); + DP(NETIF_MSG_LINK, "Add 2.5G\n"); + if (phy_ver > 0) + tmp1 |= 1; + else + tmp1 &= 0xfffe; + } else { + DP(NETIF_MSG_LINK, "Disable 2.5G\n"); + tmp1 &= 0xfffe; + } + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8073_2_5G, tmp1); + } + + /* Add support for CL37 (passive mode) II */ + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, + &tmp1); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, (tmp1 | + ((params->req_duplex == DUPLEX_FULL) ? + 0x20 : 0x40))); + + /* Add support for CL37 (passive mode) III */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_AN, 0x1000); + + if (ext_phy_type == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { + /* The SNR will improve about 2db by changing + BW and FEE main tap. Rest commands are executed + after link is up*/ + /*Change FFE main cursor to 5 in EDC register*/ + if (bnx2x_8073_is_snr_needed(params)) + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_EDC_FFE_MAIN, + 0xFB0C); + + /* Enable FEC (Forware Error Correction) + Request in the AN */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV2, &tmp1); + + tmp1 |= (1<<15); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV2, tmp1); + + } + + bnx2x_ext_phy_set_pause(params, vars); + + /* Restart autoneg */ + msleep(500); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, 0x1200); + DP(NETIF_MSG_LINK, "807x Autoneg Restart: " + "Advertise 1G=%x, 10G=%x\n", + ((val & (1<<5)) > 0), + ((val & (1<<7)) > 0)); + break; + } + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: + { + u16 tmp1; + u16 rx_alarm_ctrl_val; + u16 lasi_ctrl_val; + + /* Enable PMD link, MOD_ABS_FLT, and 1G link alarm */ + + u16 mod_abs; + rx_alarm_ctrl_val = (1<<2) | (1<<5) ; + lasi_ctrl_val = 0x0004; + + DP(NETIF_MSG_LINK, "Initializing BCM8727\n"); + /* enable LASI */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM_CTRL, + rx_alarm_ctrl_val); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, + lasi_ctrl_val); + + /* Initially configure MOD_ABS to interrupt when + module is presence( bit 8) */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs); + /* Set EDC off by setting OPTXLOS signal input to low + (bit 9). + When the EDC is off it locks onto a reference clock and + avoids becoming 'lost'.*/ + mod_abs &= ~((1<<8) | (1<<9)); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs); + + /* Make MOD_ABS give interrupt on change */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_PCS_OPT_CTRL, + &val); + val |= (1<<12); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_PCS_OPT_CTRL, + val); + + /* Set 8727 GPIOs to input to allow reading from the + 8727 GPIO0 status which reflect SFP+ module + over-current */ + + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_PCS_OPT_CTRL, + &val); + val &= 0xff8f; /* Reset bits 4-6 */ + bnx2x_cl45_write(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_PCS_OPT_CTRL, + val); + + bnx2x_8727_power_module(bp, params, ext_phy_addr, 1); + bnx2x_bcm8073_set_xaui_low_power_mode(params); + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_M8051_MSGOUT_REG, + &tmp1); + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM, &tmp1); + + /* Set option 1G speed */ + if (params->req_line_speed == SPEED_1000) { + + DP(NETIF_MSG_LINK, "Setting 1G force\n"); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, 0x40); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_10G_CTRL2, 0xD); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_10G_CTRL2, &tmp1); + DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1); + + } else if ((params->req_line_speed == + SPEED_AUTO_NEG) && + ((params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_1G))) { + + DP(NETIF_MSG_LINK, "Setting 1G clause37\n"); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, + MDIO_PMA_REG_8727_MISC_CTRL, 0); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_AN, 0x1300); + } else { + /* Since the 8727 has only single reset pin, + need to set the 10G registers although it is + default */ + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, 0x0020); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, + 0x7, 0x0100); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, 0x2040); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_10G_CTRL2, 0x0008); + } + + /* Set 2-wire transfer rate of SFP+ module EEPROM + * to 100Khz since some DACs(direct attached cables) do + * not work at 400Khz. + */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR, + 0xa001); + + /* Set TX PreEmphasis if needed */ + if ((params->feature_config_flags & + FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) { + DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x," + "TX_CTRL2 0x%x\n", + params->xgxs_config_tx[0], + params->xgxs_config_tx[1]); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_TX_CTRL1, + params->xgxs_config_tx[0]); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_TX_CTRL2, + params->xgxs_config_tx[1]); + } + + break; + } + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: + { + u16 fw_ver1, fw_ver2; + DP(NETIF_MSG_LINK, + "Setting the SFX7101 LASI indication\n"); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, 0x1); + DP(NETIF_MSG_LINK, + "Setting the SFX7101 LED to blink on traffic\n"); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_7107_LED_CNTL, (1<<3)); + + bnx2x_ext_phy_set_pause(params, vars); + /* Restart autoneg */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, &val); + val |= 0x200; + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, val); + + /* Save spirom version */ + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_7101_VER1, &fw_ver1); + + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, MDIO_PMA_DEVAD, + MDIO_PMA_REG_7101_VER2, &fw_ver2); + + bnx2x_save_spirom_version(params->bp, params->port, + params->shmem_base, + (u32)(fw_ver1<<16 | fw_ver2)); + break; + } + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823: + /* This phy uses the NIG latch mechanism since link + indication arrives through its LED4 and not via + its LASI signal, so we get steady signal + instead of clear on read */ + bnx2x_bits_en(bp, NIG_REG_LATCH_BC_0 + params->port*4, + 1 << NIG_LATCH_BC_ENABLE_MI_INT); + + bnx2x_cl45_write(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, 0x0000); + + bnx2x_8481_set_led4(params, ext_phy_type, ext_phy_addr); + if (params->req_line_speed == SPEED_AUTO_NEG) { + + u16 autoneg_val, an_1000_val, an_10_100_val; + /* set 1000 speed advertisement */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_1000T_CTRL, + &an_1000_val); + + if (params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) { + an_1000_val |= (1<<8); + if (params->req_duplex == DUPLEX_FULL) + an_1000_val |= (1<<9); + DP(NETIF_MSG_LINK, "Advertising 1G\n"); + } else + an_1000_val &= ~((1<<8) | (1<<9)); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_1000T_CTRL, + an_1000_val); + + /* set 100 speed advertisement */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_LEGACY_AN_ADV, + &an_10_100_val); + + if (params->speed_cap_mask & + (PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL | + PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF)) { + an_10_100_val |= (1<<7); + if (params->req_duplex == DUPLEX_FULL) + an_10_100_val |= (1<<8); + DP(NETIF_MSG_LINK, + "Advertising 100M\n"); + } else + an_10_100_val &= ~((1<<7) | (1<<8)); + + /* set 10 speed advertisement */ + if (params->speed_cap_mask & + (PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL | + PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF)) { + an_10_100_val |= (1<<5); + if (params->req_duplex == DUPLEX_FULL) + an_10_100_val |= (1<<6); + DP(NETIF_MSG_LINK, "Advertising 10M\n"); + } + else + an_10_100_val &= ~((1<<5) | (1<<6)); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_LEGACY_AN_ADV, + an_10_100_val); + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_LEGACY_MII_CTRL, + &autoneg_val); + + /* Disable forced speed */ + autoneg_val &= ~(1<<6|1<<13); + + /* Enable autoneg and restart autoneg + for legacy speeds */ + autoneg_val |= (1<<9|1<<12); + + if (params->req_duplex == DUPLEX_FULL) + autoneg_val |= (1<<8); + else + autoneg_val &= ~(1<<8); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_LEGACY_MII_CTRL, + autoneg_val); + + if (params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) { + DP(NETIF_MSG_LINK, "Advertising 10G\n"); + /* Restart autoneg for 10G*/ + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, 0x3200); + } + } else { + /* Force speed */ + u16 autoneg_ctrl, pma_ctrl; + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_LEGACY_MII_CTRL, + &autoneg_ctrl); + + /* Disable autoneg */ + autoneg_ctrl &= ~(1<<12); + + /* Set 1000 force */ + switch (params->req_line_speed) { + case SPEED_10000: + DP(NETIF_MSG_LINK, + "Unable to set 10G force !\n"); + break; + case SPEED_1000: + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + &pma_ctrl); + autoneg_ctrl &= ~(1<<13); + autoneg_ctrl |= (1<<6); + pma_ctrl &= ~(1<<13); + pma_ctrl |= (1<<6); + DP(NETIF_MSG_LINK, + "Setting 1000M force\n"); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + pma_ctrl); + break; + case SPEED_100: + autoneg_ctrl |= (1<<13); + autoneg_ctrl &= ~(1<<6); + DP(NETIF_MSG_LINK, + "Setting 100M force\n"); + break; + case SPEED_10: + autoneg_ctrl &= ~(1<<13); + autoneg_ctrl &= ~(1<<6); + DP(NETIF_MSG_LINK, + "Setting 10M force\n"); + break; + } + + /* Duplex mode */ + if (params->req_duplex == DUPLEX_FULL) { + autoneg_ctrl |= (1<<8); + DP(NETIF_MSG_LINK, + "Setting full duplex\n"); + } else + autoneg_ctrl &= ~(1<<8); + + /* Update autoneg ctrl and pma ctrl */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_LEGACY_MII_CTRL, + autoneg_ctrl); + } + + /* Save spirom version */ + bnx2x_save_8481_spirom_version(bp, params->port, + ext_phy_addr, + params->shmem_base); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE: + DP(NETIF_MSG_LINK, + "XGXS PHY Failure detected 0x%x\n", + params->ext_phy_config); + rc = -EINVAL; + break; + default: + DP(NETIF_MSG_LINK, "BAD XGXS ext_phy_config 0x%x\n", + params->ext_phy_config); + rc = -EINVAL; + break; + } + + } else { /* SerDes */ + + ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config); + switch (ext_phy_type) { + case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT: + DP(NETIF_MSG_LINK, "SerDes Direct\n"); + break; + + case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482: + DP(NETIF_MSG_LINK, "SerDes 5482\n"); + break; + + default: + DP(NETIF_MSG_LINK, "BAD SerDes ext_phy_config 0x%x\n", + params->ext_phy_config); + break; + } + } + return rc; +} + +static void bnx2x_8727_handle_mod_abs(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u16 mod_abs, rx_alarm_status; + u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + u32 val = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, dev_info. + port_feature_config[params->port]. + config)); + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs); + if (mod_abs & (1<<8)) { + + /* Module is absent */ + DP(NETIF_MSG_LINK, "MOD_ABS indication " + "show module is absent\n"); + + /* 1. Set mod_abs to detect next module + presence event + 2. Set EDC off by setting OPTXLOS signal input to low + (bit 9). + When the EDC is off it locks onto a reference clock and + avoids becoming 'lost'.*/ + mod_abs &= ~((1<<8)|(1<<9)); + bnx2x_cl45_write(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs); + + /* Clear RX alarm since it stays up as long as + the mod_abs wasn't changed */ + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM, &rx_alarm_status); + + } else { + /* Module is present */ + DP(NETIF_MSG_LINK, "MOD_ABS indication " + "show module is present\n"); + /* First thing, disable transmitter, + and if the module is ok, the + module_detection will enable it*/ + + /* 1. Set mod_abs to detect next module + absent event ( bit 8) + 2. Restore the default polarity of the OPRXLOS signal and + this signal will then correctly indicate the presence or + absence of the Rx signal. (bit 9) */ + mod_abs |= ((1<<8)|(1<<9)); + bnx2x_cl45_write(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs); + + /* Clear RX alarm since it stays up as long as + the mod_abs wasn't changed. This is need to be done + before calling the module detection, otherwise it will clear + the link update alarm */ + bnx2x_cl45_read(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM, &rx_alarm_status); + + + if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == + PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER) + bnx2x_sfp_set_transmitter(bp, params->port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, 0); + + if (bnx2x_wait_for_sfp_module_initialized(params) + == 0) + bnx2x_sfp_module_detection(params); + else + DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n"); + } + + DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n", + rx_alarm_status); + /* No need to check link status in case of + module plugged in/out */ +} + + +static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, + struct link_vars *vars, + u8 is_mi_int) +{ + struct bnx2x *bp = params->bp; + u32 ext_phy_type; + u8 ext_phy_addr; + u16 val1 = 0, val2; + u16 rx_sd, pcs_status; + u8 ext_phy_link_up = 0; + u8 port = params->port; + + if (vars->phy_flags & PHY_XGXS_FLAG) { + ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: + DP(NETIF_MSG_LINK, "XGXS Direct\n"); + ext_phy_link_up = 1; + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705: + DP(NETIF_MSG_LINK, "XGXS 8705\n"); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_WIS_DEVAD, + MDIO_WIS_REG_LASI_STATUS, &val1); + DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1); + + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_WIS_DEVAD, + MDIO_WIS_REG_LASI_STATUS, &val1); + DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1); + + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_SD, &rx_sd); + + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + 1, + 0xc809, &val1); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + 1, + 0xc809, &val1); + + DP(NETIF_MSG_LINK, "8705 1.c809 val=0x%x\n", val1); + ext_phy_link_up = ((rx_sd & 0x1) && (val1 & (1<<9)) && + ((val1 & (1<<8)) == 0)); + if (ext_phy_link_up) + vars->line_speed = SPEED_10000; + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: + DP(NETIF_MSG_LINK, "XGXS 8706/8726\n"); + /* Clear RX Alarm*/ + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM, + &val2); + /* clear LASI indication*/ + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, + &val1); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, + &val2); + DP(NETIF_MSG_LINK, "8706/8726 LASI status 0x%x-->" + "0x%x\n", val1, val2); + + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_SD, + &rx_sd); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, + &pcs_status); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, + &val2); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, + &val2); + + DP(NETIF_MSG_LINK, "8706/8726 rx_sd 0x%x" + " pcs_status 0x%x 1Gbps link_status 0x%x\n", + rx_sd, pcs_status, val2); + /* link is up if both bit 0 of pmd_rx_sd and + * bit 0 of pcs_status are set, or if the autoneg bit + 1 is set + */ + ext_phy_link_up = ((rx_sd & pcs_status & 0x1) || + (val2 & (1<<1))); + if (ext_phy_link_up) { + if (ext_phy_type == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) { + /* If transmitter is disabled, + ignore false link up indication */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + &val1); + if (val1 & (1<<15)) { + DP(NETIF_MSG_LINK, "Tx is " + "disabled\n"); + ext_phy_link_up = 0; + break; + } + } + if (val2 & (1<<1)) + vars->line_speed = SPEED_1000; + else + vars->line_speed = SPEED_10000; + } + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: + { + u16 link_status = 0; + u16 rx_alarm_status; + /* Check the LASI */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM, &rx_alarm_status); + + DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n", + rx_alarm_status); + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_STATUS, &val1); + + DP(NETIF_MSG_LINK, + "8727 LASI status 0x%x\n", + val1); + + /* Clear MSG-OUT */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_M8051_MSGOUT_REG, + &val1); + + /* + * If a module is present and there is need to check + * for over current + */ + if (!(params->feature_config_flags & + FEATURE_CONFIG_BCM8727_NOC) && + !(rx_alarm_status & (1<<5))) { + /* Check over-current using 8727 GPIO0 input*/ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_GPIO_CTRL, + &val1); + + if ((val1 & (1<<8)) == 0) { + DP(NETIF_MSG_LINK, "8727 Power fault" + " has been detected on " + "port %d\n", + params->port); + netdev_err(bp->dev, "Error: Power fault on Port %d has been detected and the power to that SFP+ module has been removed to prevent failure of the card. Please remove the SFP+ module and restart the system to clear this error.\n", + params->port); + /* + * Disable all RX_ALARMs except for + * mod_abs + */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM_CTRL, + (1<<5)); + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + &val1); + /* Wait for module_absent_event */ + val1 |= (1<<8); + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + val1); + /* Clear RX alarm */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM, + &rx_alarm_status); + break; + } + } /* Over current check */ + + /* When module absent bit is set, check module */ + if (rx_alarm_status & (1<<5)) { + bnx2x_8727_handle_mod_abs(params); + /* Enable all mod_abs and link detection bits */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM_CTRL, + ((1<<5) | (1<<2))); + } + + /* If transmitter is disabled, + ignore false link up indication */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + &val1); + if (val1 & (1<<15)) { + DP(NETIF_MSG_LINK, "Tx is disabled\n"); + ext_phy_link_up = 0; + break; + } + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_SPEED_LINK_STATUS, + &link_status); + + /* Bits 0..2 --> speed detected, + bits 13..15--> link is down */ + if ((link_status & (1<<2)) && + (!(link_status & (1<<15)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_10000; + } else if ((link_status & (1<<0)) && + (!(link_status & (1<<13)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_1000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 1G\n", params->port); + } else { + ext_phy_link_up = 0; + DP(NETIF_MSG_LINK, + "port %x: External link" + " is down\n", params->port); + } + break; + } + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: + { + u16 link_status = 0; + u16 an1000_status = 0; + + if (ext_phy_type == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) { + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PCS_DEVAD, + MDIO_PCS_REG_LASI_STATUS, &val1); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PCS_DEVAD, + MDIO_PCS_REG_LASI_STATUS, &val2); + DP(NETIF_MSG_LINK, + "870x LASI status 0x%x->0x%x\n", + val1, val2); + } else { + /* In 8073, port1 is directed through emac0 and + * port0 is directed through emac1 + */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_STATUS, &val1); + + DP(NETIF_MSG_LINK, + "8703 LASI status 0x%x\n", + val1); + } + + /* clear the interrupt LASI status register */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PCS_DEVAD, + MDIO_PCS_REG_STATUS, &val2); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PCS_DEVAD, + MDIO_PCS_REG_STATUS, &val1); + DP(NETIF_MSG_LINK, "807x PCS status 0x%x->0x%x\n", + val2, val1); + /* Clear MSG-OUT */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_M8051_MSGOUT_REG, + &val1); + + /* Check the LASI */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM, &val2); + + DP(NETIF_MSG_LINK, "KR 0x9003 0x%x\n", val2); + + /* Check the link status */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PCS_DEVAD, + MDIO_PCS_REG_STATUS, &val2); + DP(NETIF_MSG_LINK, "KR PCS status 0x%x\n", val2); + + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_STATUS, &val2); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_STATUS, &val1); + ext_phy_link_up = ((val1 & 4) == 4); + DP(NETIF_MSG_LINK, "PMA_REG_STATUS=0x%x\n", val1); + if (ext_phy_type == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { + + if (ext_phy_link_up && + ((params->req_line_speed != + SPEED_10000))) { + if (bnx2x_bcm8073_xaui_wa(params) + != 0) { + ext_phy_link_up = 0; + break; + } + } + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_LINK_STATUS, + &an1000_status); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_LINK_STATUS, + &an1000_status); + + /* Check the link status on 1.1.2 */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_STATUS, &val2); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_STATUS, &val1); + DP(NETIF_MSG_LINK, "KR PMA status 0x%x->0x%x," + "an_link_status=0x%x\n", + val2, val1, an1000_status); + + ext_phy_link_up = (((val1 & 4) == 4) || + (an1000_status & (1<<1))); + if (ext_phy_link_up && + bnx2x_8073_is_snr_needed(params)) { + /* The SNR will improve about 2dbby + changing the BW and FEE main tap.*/ + + /* The 1st write to change FFE main + tap is set before restart AN */ + /* Change PLL Bandwidth in EDC + register */ + bnx2x_cl45_write(bp, port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PLL_BANDWIDTH, + 0x26BC); + + /* Change CDR Bandwidth in EDC + register */ + bnx2x_cl45_write(bp, port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CDR_BANDWIDTH, + 0x0333); + } + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_SPEED_LINK_STATUS, + &link_status); + + /* Bits 0..2 --> speed detected, + bits 13..15--> link is down */ + if ((link_status & (1<<2)) && + (!(link_status & (1<<15)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_10000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 10G\n", params->port); + } else if ((link_status & (1<<1)) && + (!(link_status & (1<<14)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_2500; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 2.5G\n", params->port); + } else if ((link_status & (1<<0)) && + (!(link_status & (1<<13)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_1000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 1G\n", params->port); + } else { + ext_phy_link_up = 0; + DP(NETIF_MSG_LINK, + "port %x: External link" + " is down\n", params->port); + } + } else { + /* See if 1G link is up for the 8072 */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_LINK_STATUS, + &an1000_status); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_LINK_STATUS, + &an1000_status); + if (an1000_status & (1<<1)) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_1000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 1G\n", params->port); + } else if (ext_phy_link_up) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_10000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 10G\n", params->port); + } + } + + + break; + } + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_STATUS, &val2); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_STATUS, &val1); + DP(NETIF_MSG_LINK, + "10G-base-T LASI status 0x%x->0x%x\n", + val2, val1); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_STATUS, &val2); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_STATUS, &val1); + DP(NETIF_MSG_LINK, + "10G-base-T PMA status 0x%x->0x%x\n", + val2, val1); + ext_phy_link_up = ((val1 & 4) == 4); + /* if link is up + * print the AN outcome of the SFX7101 PHY + */ + if (ext_phy_link_up) { + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_MASTER_STATUS, + &val2); + vars->line_speed = SPEED_10000; + DP(NETIF_MSG_LINK, + "SFX7101 AN status 0x%x->Master=%x\n", + val2, + (val2 & (1<<14))); + } + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823: + /* Check 10G-BaseT link status */ + /* Check PMD signal ok */ + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + 0xFFFA, + &val1); + bnx2x_cl45_read(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_PMD_SIGNAL, + &val2); + DP(NETIF_MSG_LINK, "PMD_SIGNAL 1.a811 = 0x%x\n", val2); + + /* Check link 10G */ + if (val2 & (1<<11)) { + vars->line_speed = SPEED_10000; + ext_phy_link_up = 1; + bnx2x_8481_set_10G_led_mode(params, + ext_phy_type, + ext_phy_addr); + } else { /* Check Legacy speed link */ + u16 legacy_status, legacy_speed; + + /* Enable expansion register 0x42 + (Operation mode status) */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_EXPANSION_REG_ACCESS, + 0xf42); + + /* Get legacy speed operation status */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_8481_EXPANSION_REG_RD_RW, + &legacy_status); + + DP(NETIF_MSG_LINK, "Legacy speed status" + " = 0x%x\n", legacy_status); + ext_phy_link_up = ((legacy_status & (1<<11)) + == (1<<11)); + if (ext_phy_link_up) { + legacy_speed = (legacy_status & (3<<9)); + if (legacy_speed == (0<<9)) + vars->line_speed = SPEED_10; + else if (legacy_speed == (1<<9)) + vars->line_speed = + SPEED_100; + else if (legacy_speed == (2<<9)) + vars->line_speed = + SPEED_1000; + else /* Should not happen */ + vars->line_speed = 0; + + if (legacy_status & (1<<8)) + vars->duplex = DUPLEX_FULL; + else + vars->duplex = DUPLEX_HALF; + + DP(NETIF_MSG_LINK, "Link is up " + "in %dMbps, is_duplex_full" + "= %d\n", + vars->line_speed, + (vars->duplex == DUPLEX_FULL)); + bnx2x_8481_set_legacy_led_mode(params, + ext_phy_type, + ext_phy_addr); + } + } + break; + default: + DP(NETIF_MSG_LINK, "BAD XGXS ext_phy_config 0x%x\n", + params->ext_phy_config); + ext_phy_link_up = 0; + break; + } + /* Set SGMII mode for external phy */ + if (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) { + if (vars->line_speed < SPEED_1000) + vars->phy_flags |= PHY_SGMII_FLAG; + else + vars->phy_flags &= ~PHY_SGMII_FLAG; + } + + } else { /* SerDes */ + ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config); + switch (ext_phy_type) { + case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT: + DP(NETIF_MSG_LINK, "SerDes Direct\n"); + ext_phy_link_up = 1; + break; + + case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482: + DP(NETIF_MSG_LINK, "SerDes 5482\n"); + ext_phy_link_up = 1; + break; + + default: + DP(NETIF_MSG_LINK, + "BAD SerDes ext_phy_config 0x%x\n", + params->ext_phy_config); + ext_phy_link_up = 0; + break; + } + } + + return ext_phy_link_up; +} + +static void bnx2x_link_int_enable(struct link_params *params) +{ + u8 port = params->port; + u32 ext_phy_type; + u32 mask; + struct bnx2x *bp = params->bp; + + /* setting the status to report on link up + for either XGXS or SerDes */ + + if (params->switch_cfg == SWITCH_CFG_10G) { + mask = (NIG_MASK_XGXS0_LINK10G | + NIG_MASK_XGXS0_LINK_STATUS); + DP(NETIF_MSG_LINK, "enabled XGXS interrupt\n"); + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + if ((ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) && + (ext_phy_type != + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)) { + mask |= NIG_MASK_MI_INT; + DP(NETIF_MSG_LINK, "enabled external phy int\n"); + } + + } else { /* SerDes */ + mask = NIG_MASK_SERDES0_LINK_STATUS; + DP(NETIF_MSG_LINK, "enabled SerDes interrupt\n"); + ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config); + if ((ext_phy_type != + PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT) && + (ext_phy_type != + PORT_HW_CFG_SERDES_EXT_PHY_TYPE_NOT_CONN)) { + mask |= NIG_MASK_MI_INT; + DP(NETIF_MSG_LINK, "enabled external phy int\n"); + } + } + bnx2x_bits_en(bp, + NIG_REG_MASK_INTERRUPT_PORT0 + port*4, + mask); + + DP(NETIF_MSG_LINK, "port %x, is_xgxs %x, int_status 0x%x\n", port, + (params->switch_cfg == SWITCH_CFG_10G), + REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4)); + DP(NETIF_MSG_LINK, " int_mask 0x%x, MI_INT %x, SERDES_LINK %x\n", + REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4), + REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + port*0x18), + REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS+port*0x3c)); + DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n", + REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68), + REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68)); +} + +static void bnx2x_8481_rearm_latch_signal(struct bnx2x *bp, u8 port, + u8 is_mi_int) +{ + u32 latch_status = 0, is_mi_int_status; + /* Disable the MI INT ( external phy int ) + * by writing 1 to the status register. Link down indication + * is high-active-signal, so in this case we need to write the + * status to clear the XOR + */ + /* Read Latched signals */ + latch_status = REG_RD(bp, + NIG_REG_LATCH_STATUS_0 + port*8); + is_mi_int_status = REG_RD(bp, + NIG_REG_STATUS_INTERRUPT_PORT0 + port*4); + DP(NETIF_MSG_LINK, "original_signal = 0x%x, nig_status = 0x%x," + "latch_status = 0x%x\n", + is_mi_int, is_mi_int_status, latch_status); + /* Handle only those with latched-signal=up.*/ + if (latch_status & 1) { + /* For all latched-signal=up,Write original_signal to status */ + if (is_mi_int) + bnx2x_bits_en(bp, + NIG_REG_STATUS_INTERRUPT_PORT0 + + port*4, + NIG_STATUS_EMAC0_MI_INT); + else + bnx2x_bits_dis(bp, + NIG_REG_STATUS_INTERRUPT_PORT0 + + port*4, + NIG_STATUS_EMAC0_MI_INT); + /* For all latched-signal=up : Re-Arm Latch signals */ + REG_WR(bp, NIG_REG_LATCH_STATUS_0 + port*8, + (latch_status & 0xfffe) | (latch_status & 1)); + } +} +/* + * link management + */ +static void bnx2x_link_int_ack(struct link_params *params, + struct link_vars *vars, u8 is_10g, + u8 is_mi_int) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + + /* first reset all status + * we assume only one line will be change at a time */ + bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, + (NIG_STATUS_XGXS0_LINK10G | + NIG_STATUS_XGXS0_LINK_STATUS | + NIG_STATUS_SERDES0_LINK_STATUS)); + if ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) + == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481) || + (XGXS_EXT_PHY_TYPE(params->ext_phy_config) + == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823)) { + bnx2x_8481_rearm_latch_signal(bp, port, is_mi_int); + } + if (vars->phy_link_up) { + if (is_10g) { + /* Disable the 10G link interrupt + * by writing 1 to the status register + */ + DP(NETIF_MSG_LINK, "10G XGXS phy link up\n"); + bnx2x_bits_en(bp, + NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, + NIG_STATUS_XGXS0_LINK10G); + + } else if (params->switch_cfg == SWITCH_CFG_10G) { + /* Disable the link interrupt + * by writing 1 to the relevant lane + * in the status register + */ + u32 ser_lane = ((params->lane_config & + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); + + DP(NETIF_MSG_LINK, "%d speed XGXS phy link up\n", + vars->line_speed); + bnx2x_bits_en(bp, + NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, + ((1 << ser_lane) << + NIG_STATUS_XGXS0_LINK_STATUS_SIZE)); + + } else { /* SerDes */ + DP(NETIF_MSG_LINK, "SerDes phy link up\n"); + /* Disable the link interrupt + * by writing 1 to the status register + */ + bnx2x_bits_en(bp, + NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, + NIG_STATUS_SERDES0_LINK_STATUS); + } + + } else { /* link_down */ + } +} + +static u8 bnx2x_format_ver(u32 num, u8 *str, u16 len) +{ + u8 *str_ptr = str; + u32 mask = 0xf0000000; + u8 shift = 8*4; + u8 digit; + if (len < 10) { + /* Need more than 10chars for this format */ + *str_ptr = '\0'; + return -EINVAL; + } + while (shift > 0) { + + shift -= 4; + digit = ((num & mask) >> shift); + if (digit < 0xa) + *str_ptr = digit + '0'; + else + *str_ptr = digit - 0xa + 'a'; + str_ptr++; + mask = mask >> 4; + if (shift == 4*4) { + *str_ptr = ':'; + str_ptr++; + } + } + *str_ptr = '\0'; + return 0; +} + +u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, + u8 *version, u16 len) +{ + struct bnx2x *bp; + u32 ext_phy_type = 0; + u32 spirom_ver = 0; + u8 status; + + if (version == NULL || params == NULL) + return -EINVAL; + bp = params->bp; + + spirom_ver = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, + port_mb[params->port].ext_phy_fw_version)); + + status = 0; + /* reset the returned value to zero */ + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: + + if (len < 5) + return -EINVAL; + + version[0] = (spirom_ver & 0xFF); + version[1] = (spirom_ver & 0xFF00) >> 8; + version[2] = (spirom_ver & 0xFF0000) >> 16; + version[3] = (spirom_ver & 0xFF000000) >> 24; + version[4] = '\0'; + + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: + status = bnx2x_format_ver(spirom_ver, version, len); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823: + spirom_ver = ((spirom_ver & 0xF80) >> 7) << 16 | + (spirom_ver & 0x7F); + status = bnx2x_format_ver(spirom_ver, version, len); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705: + version[0] = '\0'; + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE: + DP(NETIF_MSG_LINK, "bnx2x_get_ext_phy_fw_version:" + " type is FAILURE!\n"); + status = -EINVAL; + break; + + default: + break; + } + return status; +} + +static void bnx2x_set_xgxs_loopback(struct link_params *params, + struct link_vars *vars, + u8 is_10g) +{ + u8 port = params->port; + struct bnx2x *bp = params->bp; + + if (is_10g) { + u32 md_devad; + + DP(NETIF_MSG_LINK, "XGXS 10G loopback enable\n"); + + /* change the uni_phy_addr in the nig */ + md_devad = REG_RD(bp, (NIG_REG_XGXS0_CTRL_MD_DEVAD + + port*0x18)); + + REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, 0x5); + + bnx2x_cl45_write(bp, port, 0, + params->phy_addr, + 5, + (MDIO_REG_BANK_AER_BLOCK + + (MDIO_AER_BLOCK_AER_REG & 0xf)), + 0x2800); + + bnx2x_cl45_write(bp, port, 0, + params->phy_addr, + 5, + (MDIO_REG_BANK_CL73_IEEEB0 + + (MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)), + 0x6041); + msleep(200); + /* set aer mmd back */ + bnx2x_set_aer_mmd(params, vars); + + /* and md_devad */ + REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, + md_devad); + + } else { + u16 mii_control; + + DP(NETIF_MSG_LINK, "XGXS 1G loopback enable\n"); + + CL45_RD_OVER_CL22(bp, port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + &mii_control); + + CL45_WR_OVER_CL22(bp, port, + params->phy_addr, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + (mii_control | + MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK)); + } +} + + +static void bnx2x_ext_phy_loopback(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u8 ext_phy_addr; + u32 ext_phy_type; + + if (params->switch_cfg == SWITCH_CFG_10G) { + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config); + /* CL37 Autoneg Enabled */ + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN: + DP(NETIF_MSG_LINK, + "ext_phy_loopback: We should not get here\n"); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705: + DP(NETIF_MSG_LINK, "ext_phy_loopback: 8705\n"); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: + DP(NETIF_MSG_LINK, "ext_phy_loopback: 8706\n"); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: + DP(NETIF_MSG_LINK, "PMA/PMD ext_phy_loopback: 8726\n"); + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 0x0001); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: + /* SFX7101_XGXS_TEST1 */ + bnx2x_cl45_write(bp, params->port, ext_phy_type, + ext_phy_addr, + MDIO_XS_DEVAD, + MDIO_XS_SFX7101_XGXS_TEST1, + 0x100); + DP(NETIF_MSG_LINK, + "ext_phy_loopback: set ext phy loopback\n"); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: + + break; + } /* switch external PHY type */ + } else { + /* serdes */ + ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config); + ext_phy_addr = (params->ext_phy_config & + PORT_HW_CFG_SERDES_EXT_PHY_ADDR_MASK) + >> PORT_HW_CFG_SERDES_EXT_PHY_ADDR_SHIFT; + } +} + + +/* + *------------------------------------------------------------------------ + * bnx2x_override_led_value - + * + * Override the led value of the requsted led + * + *------------------------------------------------------------------------ + */ +u8 bnx2x_override_led_value(struct bnx2x *bp, u8 port, + u32 led_idx, u32 value) +{ + u32 reg_val; + + /* If port 0 then use EMAC0, else use EMAC1*/ + u32 emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0; + + DP(NETIF_MSG_LINK, + "bnx2x_override_led_value() port %x led_idx %d value %d\n", + port, led_idx, value); + + switch (led_idx) { + case 0: /* 10MB led */ + /* Read the current value of the LED register in + the EMAC block */ + reg_val = REG_RD(bp, emac_base + EMAC_REG_EMAC_LED); + /* Set the OVERRIDE bit to 1 */ + reg_val |= EMAC_LED_OVERRIDE; + /* If value is 1, set the 10M_OVERRIDE bit, + otherwise reset it.*/ + reg_val = (value == 1) ? (reg_val | EMAC_LED_10MB_OVERRIDE) : + (reg_val & ~EMAC_LED_10MB_OVERRIDE); + REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val); + break; + case 1: /*100MB led */ + /*Read the current value of the LED register in + the EMAC block */ + reg_val = REG_RD(bp, emac_base + EMAC_REG_EMAC_LED); + /* Set the OVERRIDE bit to 1 */ + reg_val |= EMAC_LED_OVERRIDE; + /* If value is 1, set the 100M_OVERRIDE bit, + otherwise reset it.*/ + reg_val = (value == 1) ? (reg_val | EMAC_LED_100MB_OVERRIDE) : + (reg_val & ~EMAC_LED_100MB_OVERRIDE); + REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val); + break; + case 2: /* 1000MB led */ + /* Read the current value of the LED register in the + EMAC block */ + reg_val = REG_RD(bp, emac_base + EMAC_REG_EMAC_LED); + /* Set the OVERRIDE bit to 1 */ + reg_val |= EMAC_LED_OVERRIDE; + /* If value is 1, set the 1000M_OVERRIDE bit, otherwise + reset it. */ + reg_val = (value == 1) ? (reg_val | EMAC_LED_1000MB_OVERRIDE) : + (reg_val & ~EMAC_LED_1000MB_OVERRIDE); + REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val); + break; + case 3: /* 2500MB led */ + /* Read the current value of the LED register in the + EMAC block*/ + reg_val = REG_RD(bp, emac_base + EMAC_REG_EMAC_LED); + /* Set the OVERRIDE bit to 1 */ + reg_val |= EMAC_LED_OVERRIDE; + /* If value is 1, set the 2500M_OVERRIDE bit, otherwise + reset it.*/ + reg_val = (value == 1) ? (reg_val | EMAC_LED_2500MB_OVERRIDE) : + (reg_val & ~EMAC_LED_2500MB_OVERRIDE); + REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val); + break; + case 4: /*10G led */ + if (port == 0) { + REG_WR(bp, NIG_REG_LED_10G_P0, + value); + } else { + REG_WR(bp, NIG_REG_LED_10G_P1, + value); + } + break; + case 5: /* TRAFFIC led */ + /* Find if the traffic control is via BMAC or EMAC */ + if (port == 0) + reg_val = REG_RD(bp, NIG_REG_NIG_EMAC0_EN); + else + reg_val = REG_RD(bp, NIG_REG_NIG_EMAC1_EN); + + /* Override the traffic led in the EMAC:*/ + if (reg_val == 1) { + /* Read the current value of the LED register in + the EMAC block */ + reg_val = REG_RD(bp, emac_base + + EMAC_REG_EMAC_LED); + /* Set the TRAFFIC_OVERRIDE bit to 1 */ + reg_val |= EMAC_LED_OVERRIDE; + /* If value is 1, set the TRAFFIC bit, otherwise + reset it.*/ + reg_val = (value == 1) ? (reg_val | EMAC_LED_TRAFFIC) : + (reg_val & ~EMAC_LED_TRAFFIC); + REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val); + } else { /* Override the traffic led in the BMAC: */ + REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + + port*4, 1); + REG_WR(bp, NIG_REG_LED_CONTROL_TRAFFIC_P0 + port*4, + value); + } + break; + default: + DP(NETIF_MSG_LINK, + "bnx2x_override_led_value() unknown led index %d " + "(should be 0-5)\n", led_idx); + return -EINVAL; + } + + return 0; +} + + +u8 bnx2x_set_led(struct link_params *params, u8 mode, u32 speed) +{ + u8 port = params->port; + u16 hw_led_mode = params->hw_led_mode; + u8 rc = 0; + u32 tmp; + u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + struct bnx2x *bp = params->bp; + DP(NETIF_MSG_LINK, "bnx2x_set_led: port %x, mode %d\n", port, mode); + DP(NETIF_MSG_LINK, "speed 0x%x, hw_led_mode 0x%x\n", + speed, hw_led_mode); + switch (mode) { + case LED_MODE_OFF: + REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 0); + REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, + SHARED_HW_CFG_LED_MAC1); + + tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); + EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE)); + break; + + case LED_MODE_OPER: + if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) { + REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0); + REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1); + } else { + REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, + hw_led_mode); + } + + REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + + port*4, 0); + /* Set blinking rate to ~15.9Hz */ + REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_P0 + port*4, + LED_BLINK_RATE_VAL); + REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 + + port*4, 1); + tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); + EMAC_WR(bp, EMAC_REG_EMAC_LED, + (tmp & (~EMAC_LED_OVERRIDE))); + + if (CHIP_IS_E1(bp) && + ((speed == SPEED_2500) || + (speed == SPEED_1000) || + (speed == SPEED_100) || + (speed == SPEED_10))) { + /* On Everest 1 Ax chip versions for speeds less than + 10G LED scheme is different */ + REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + + port*4, 1); + REG_WR(bp, NIG_REG_LED_CONTROL_TRAFFIC_P0 + + port*4, 0); + REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 + + port*4, 1); + } + break; + + default: + rc = -EINVAL; + DP(NETIF_MSG_LINK, "bnx2x_set_led: Invalid led mode %d\n", + mode); + break; + } + return rc; + +} + +u8 bnx2x_test_link(struct link_params *params, struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u16 gp_status = 0; + + CL45_RD_OVER_CL22(bp, params->port, + params->phy_addr, + MDIO_REG_BANK_GP_STATUS, + MDIO_GP_STATUS_TOP_AN_STATUS1, + &gp_status); + /* link is up only if both local phy and external phy are up */ + if ((gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) && + bnx2x_ext_phy_is_link_up(params, vars, 1)) + return 0; + + return -ESRCH; +} + +static u8 bnx2x_link_initialize(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 rc = 0; + u8 non_ext_phy; + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + /* Activate the external PHY */ + bnx2x_ext_phy_reset(params, vars); + + bnx2x_set_aer_mmd(params, vars); + + if (vars->phy_flags & PHY_XGXS_FLAG) + bnx2x_set_master_ln(params); + + rc = bnx2x_reset_unicore(params); + /* reset the SerDes and wait for reset bit return low */ + if (rc != 0) + return rc; + + bnx2x_set_aer_mmd(params, vars); + + /* setting the masterLn_def again after the reset */ + if (vars->phy_flags & PHY_XGXS_FLAG) { + bnx2x_set_master_ln(params); + bnx2x_set_swap_lanes(params); + } + + if (vars->phy_flags & PHY_XGXS_FLAG) { + if ((params->req_line_speed && + ((params->req_line_speed == SPEED_100) || + (params->req_line_speed == SPEED_10))) || + (!params->req_line_speed && + (params->speed_cap_mask >= + PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) && + (params->speed_cap_mask < + PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) + )) { + vars->phy_flags |= PHY_SGMII_FLAG; + } else { + vars->phy_flags &= ~PHY_SGMII_FLAG; + } + } + /* In case of external phy existance, the line speed would be the + line speed linked up by the external phy. In case it is direct only, + then the line_speed during initialization will be equal to the + req_line_speed*/ + vars->line_speed = params->req_line_speed; + + bnx2x_calc_ieee_aneg_adv(params, &vars->ieee_fc); + + /* init ext phy and enable link state int */ + non_ext_phy = ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) || + (params->loopback_mode == LOOPBACK_XGXS_10)); + + if (non_ext_phy || + (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) || + (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706) || + (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) || + (params->loopback_mode == LOOPBACK_EXT_PHY)) { + if (params->req_line_speed == SPEED_AUTO_NEG) + bnx2x_set_parallel_detection(params, vars->phy_flags); + bnx2x_init_internal_phy(params, vars, non_ext_phy); + } + + if (!non_ext_phy) + rc |= bnx2x_ext_phy_init(params, vars); + + bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, + (NIG_STATUS_XGXS0_LINK10G | + NIG_STATUS_XGXS0_LINK_STATUS | + NIG_STATUS_SERDES0_LINK_STATUS)); + + return rc; + +} + + +u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u32 val; + + DP(NETIF_MSG_LINK, "Phy Initialization started\n"); + DP(NETIF_MSG_LINK, "req_speed %d, req_flowctrl %d\n", + params->req_line_speed, params->req_flow_ctrl); + vars->link_status = 0; + vars->phy_link_up = 0; + vars->link_up = 0; + vars->line_speed = 0; + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; + vars->mac_type = MAC_TYPE_NONE; + + if (params->switch_cfg == SWITCH_CFG_1G) + vars->phy_flags = PHY_SERDES_FLAG; + else + vars->phy_flags = PHY_XGXS_FLAG; + + /* disable attentions */ + bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4, + (NIG_MASK_XGXS0_LINK_STATUS | + NIG_MASK_XGXS0_LINK10G | + NIG_MASK_SERDES0_LINK_STATUS | + NIG_MASK_MI_INT)); + + bnx2x_emac_init(params, vars); + + if (CHIP_REV_IS_FPGA(bp)) { + + vars->link_up = 1; + vars->line_speed = SPEED_10000; + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; + vars->link_status = (LINK_STATUS_LINK_UP | LINK_10GTFD); + /* enable on E1.5 FPGA */ + if (CHIP_IS_E1H(bp)) { + vars->flow_ctrl |= + (BNX2X_FLOW_CTRL_TX | + BNX2X_FLOW_CTRL_RX); + vars->link_status |= + (LINK_STATUS_TX_FLOW_CONTROL_ENABLED | + LINK_STATUS_RX_FLOW_CONTROL_ENABLED); + } + + bnx2x_emac_enable(params, vars, 0); + bnx2x_pbf_update(params, vars->flow_ctrl, vars->line_speed); + /* disable drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); + + /* update shared memory */ + bnx2x_update_mng(params, vars->link_status); + + return 0; + + } else + if (CHIP_REV_IS_EMUL(bp)) { + + vars->link_up = 1; + vars->line_speed = SPEED_10000; + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; + vars->link_status = (LINK_STATUS_LINK_UP | LINK_10GTFD); + + bnx2x_bmac_enable(params, vars, 0); + + bnx2x_pbf_update(params, vars->flow_ctrl, vars->line_speed); + /* Disable drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + + params->port*4, 0); + + /* update shared memory */ + bnx2x_update_mng(params, vars->link_status); + + return 0; + + } else + if (params->loopback_mode == LOOPBACK_BMAC) { + + vars->link_up = 1; + vars->line_speed = SPEED_10000; + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; + vars->mac_type = MAC_TYPE_BMAC; + + vars->phy_flags = PHY_XGXS_FLAG; + + bnx2x_phy_deassert(params, vars->phy_flags); + /* set bmac loopback */ + bnx2x_bmac_enable(params, vars, 1); + + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + + params->port*4, 0); + + } else if (params->loopback_mode == LOOPBACK_EMAC) { + + vars->link_up = 1; + vars->line_speed = SPEED_1000; + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; + vars->mac_type = MAC_TYPE_EMAC; + + vars->phy_flags = PHY_XGXS_FLAG; + + bnx2x_phy_deassert(params, vars->phy_flags); + /* set bmac loopback */ + bnx2x_emac_enable(params, vars, 1); + bnx2x_emac_program(params, vars->line_speed, + vars->duplex); + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + + params->port*4, 0); + + } else if ((params->loopback_mode == LOOPBACK_XGXS_10) || + (params->loopback_mode == LOOPBACK_EXT_PHY)) { + + vars->link_up = 1; + vars->line_speed = SPEED_10000; + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; + + vars->phy_flags = PHY_XGXS_FLAG; + + val = REG_RD(bp, + NIG_REG_XGXS0_CTRL_PHY_ADDR+ + params->port*0x18); + params->phy_addr = (u8)val; + + bnx2x_phy_deassert(params, vars->phy_flags); + bnx2x_link_initialize(params, vars); + + vars->mac_type = MAC_TYPE_BMAC; + + bnx2x_bmac_enable(params, vars, 0); + + if (params->loopback_mode == LOOPBACK_XGXS_10) { + /* set 10G XGXS loopback */ + bnx2x_set_xgxs_loopback(params, vars, 1); + } else { + /* set external phy loopback */ + bnx2x_ext_phy_loopback(params); + } + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + + params->port*4, 0); + + bnx2x_set_led(params, LED_MODE_OPER, vars->line_speed); + } else + /* No loopback */ + { + bnx2x_phy_deassert(params, vars->phy_flags); + switch (params->switch_cfg) { + case SWITCH_CFG_1G: + vars->phy_flags |= PHY_SERDES_FLAG; + if ((params->ext_phy_config & + PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK) == + PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482) { + vars->phy_flags |= PHY_SGMII_FLAG; + } + + val = REG_RD(bp, + NIG_REG_SERDES0_CTRL_PHY_ADDR+ + params->port*0x10); + + params->phy_addr = (u8)val; + + break; + case SWITCH_CFG_10G: + vars->phy_flags |= PHY_XGXS_FLAG; + val = REG_RD(bp, + NIG_REG_XGXS0_CTRL_PHY_ADDR+ + params->port*0x18); + params->phy_addr = (u8)val; + + break; + default: + DP(NETIF_MSG_LINK, "Invalid switch_cfg\n"); + return -EINVAL; + } + DP(NETIF_MSG_LINK, "Phy address = 0x%x\n", params->phy_addr); + + bnx2x_link_initialize(params, vars); + msleep(30); + bnx2x_link_int_enable(params); + } + return 0; +} + +static void bnx2x_8726_reset_phy(struct bnx2x *bp, u8 port, u8 ext_phy_addr) +{ + DP(NETIF_MSG_LINK, "bnx2x_8726_reset_phy port %d\n", port); + + /* Set serial boot control for external load */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, 0x0001); +} + +u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars, + u8 reset_ext_phy) +{ + struct bnx2x *bp = params->bp; + u32 ext_phy_config = params->ext_phy_config; + u8 port = params->port; + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config); + u32 val = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, dev_info. + port_feature_config[params->port]. + config)); + DP(NETIF_MSG_LINK, "Resetting the link of port %d\n", port); + /* disable attentions */ + vars->link_status = 0; + bnx2x_update_mng(params, vars->link_status); + bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, + (NIG_MASK_XGXS0_LINK_STATUS | + NIG_MASK_XGXS0_LINK10G | + NIG_MASK_SERDES0_LINK_STATUS | + NIG_MASK_MI_INT)); + + /* activate nig drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1); + + /* disable nig egress interface */ + REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0); + REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0); + + /* Stop BigMac rx */ + bnx2x_bmac_rx_disable(bp, port); + + /* disable emac */ + REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0); + + msleep(10); + /* The PHY reset is controled by GPIO 1 + * Hold it as vars low + */ + /* clear link led */ + bnx2x_set_led(params, LED_MODE_OFF, 0); + if (reset_ext_phy) { + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: + { + + /* Disable Transmitter */ + u8 ext_phy_addr = + XGXS_EXT_PHY_ADDR(params->ext_phy_config); + if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == + PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER) + bnx2x_sfp_set_transmitter(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr, 0); + break; + } + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: + DP(NETIF_MSG_LINK, "Setting 8073 port %d into " + "low power mode\n", + port); + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: + { + u8 ext_phy_addr = + XGXS_EXT_PHY_ADDR(params->ext_phy_config); + /* Set soft reset */ + bnx2x_8726_reset_phy(bp, params->port, ext_phy_addr); + break; + } + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823: + { + u8 ext_phy_addr = + XGXS_EXT_PHY_ADDR(params->ext_phy_config); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, 0x0000); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, 1); + break; + } + default: + /* HW reset */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); + DP(NETIF_MSG_LINK, "reset external PHY\n"); + } + } + /* reset the SerDes/XGXS */ + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, + (0x1ff << (port*16))); + + /* reset BigMac */ + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + + /* disable nig ingress interface */ + REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0); + REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0); + REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0); + REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0); + vars->link_up = 0; + return 0; +} + +static u8 bnx2x_update_link_down(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + + DP(NETIF_MSG_LINK, "Port %x: Link is down\n", port); + bnx2x_set_led(params, LED_MODE_OFF, 0); + + /* indicate no mac active */ + vars->mac_type = MAC_TYPE_NONE; + + /* update shared memory */ + vars->link_status = 0; + vars->line_speed = 0; + bnx2x_update_mng(params, vars->link_status); + + /* activate nig drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1); + + /* disable emac */ + REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0); + + msleep(10); + + /* reset BigMac */ + bnx2x_bmac_rx_disable(bp, params->port); + REG_WR(bp, GRCBASE_MISC + + MISC_REGISTERS_RESET_REG_2_CLEAR, + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + return 0; +} + +static u8 bnx2x_update_link_up(struct link_params *params, + struct link_vars *vars, + u8 link_10g, u32 gp_status) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 rc = 0; + + vars->link_status |= LINK_STATUS_LINK_UP; + if (link_10g) { + bnx2x_bmac_enable(params, vars, 0); + bnx2x_set_led(params, LED_MODE_OPER, SPEED_10000); + } else { + rc = bnx2x_emac_program(params, vars->line_speed, + vars->duplex); + + bnx2x_emac_enable(params, vars, 0); + + /* AN complete? */ + if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) { + if (!(vars->phy_flags & + PHY_SGMII_FLAG)) + bnx2x_set_gmii_tx_driver(params); + } + } + + /* PBF - link up */ + rc |= bnx2x_pbf_update(params, vars->flow_ctrl, + vars->line_speed); + + /* disable drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0); + + /* update shared memory */ + bnx2x_update_mng(params, vars->link_status); + msleep(20); + return rc; +} +/* This function should called upon link interrupt */ +/* In case vars->link_up, driver needs to + 1. Update the pbf + 2. Disable drain + 3. Update the shared memory + 4. Indicate link up + 5. Set LEDs + Otherwise, + 1. Update shared memory + 2. Reset BigMac + 3. Report link down + 4. Unset LEDs +*/ +u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u16 gp_status; + u8 link_10g; + u8 ext_phy_link_up, rc = 0; + u32 ext_phy_type; + u8 is_mi_int = 0; + + DP(NETIF_MSG_LINK, "port %x, XGXS?%x, int_status 0x%x\n", + port, (vars->phy_flags & PHY_XGXS_FLAG), + REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4)); + + is_mi_int = (u8)(REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + + port*0x18) > 0); + DP(NETIF_MSG_LINK, "int_mask 0x%x MI_INT %x, SERDES_LINK %x\n", + REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4), + is_mi_int, + REG_RD(bp, + NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c)); + + DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n", + REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68), + REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68)); + + /* disable emac */ + REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0); + + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + /* Check external link change only for non-direct */ + ext_phy_link_up = bnx2x_ext_phy_is_link_up(params, vars, is_mi_int); + + /* Read gp_status */ + CL45_RD_OVER_CL22(bp, port, params->phy_addr, + MDIO_REG_BANK_GP_STATUS, + MDIO_GP_STATUS_TOP_AN_STATUS1, + &gp_status); + + rc = bnx2x_link_settings_status(params, vars, gp_status, + ext_phy_link_up); + if (rc != 0) + return rc; + + /* anything 10 and over uses the bmac */ + link_10g = ((vars->line_speed == SPEED_10000) || + (vars->line_speed == SPEED_12000) || + (vars->line_speed == SPEED_12500) || + (vars->line_speed == SPEED_13000) || + (vars->line_speed == SPEED_15000) || + (vars->line_speed == SPEED_16000)); + + bnx2x_link_int_ack(params, vars, link_10g, is_mi_int); + + /* In case external phy link is up, and internal link is down + ( not initialized yet probably after link initialization, it needs + to be initialized. + Note that after link down-up as result of cable plug, + the xgxs link would probably become up again without the need to + initialize it*/ + + if ((ext_phy_type != PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) && + (ext_phy_link_up && !vars->phy_link_up)) + bnx2x_init_internal_phy(params, vars, 0); + + /* link is up only if both local phy and external phy are up */ + vars->link_up = (ext_phy_link_up && vars->phy_link_up); + + if (vars->link_up) + rc = bnx2x_update_link_up(params, vars, link_10g, gp_status); + else + rc = bnx2x_update_link_down(params, vars); + + return rc; +} + +static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, u32 shmem_base) +{ + u8 ext_phy_addr[PORT_MAX]; + u16 val; + s8 port; + + /* PART1 - Reset both phys */ + for (port = PORT_MAX - 1; port >= PORT_0; port--) { + /* Extract the ext phy address for the port */ + u32 ext_phy_config = REG_RD(bp, shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[port].external_phy_config)); + + /* disable attentions */ + bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, + (NIG_MASK_XGXS0_LINK_STATUS | + NIG_MASK_XGXS0_LINK10G | + NIG_MASK_SERDES0_LINK_STATUS | + NIG_MASK_MI_INT)); + + ext_phy_addr[port] = XGXS_EXT_PHY_ADDR(ext_phy_config); + + /* Need to take the phy out of low power mode in order + to write to access its registers */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); + + /* Reset the phy */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 1<<15); + } + + /* Add delay of 150ms after reset */ + msleep(150); + + /* PART2 - Download firmware to both phys */ + for (port = PORT_MAX - 1; port >= PORT_0; port--) { + u16 fw_ver1; + + bnx2x_bcm8073_external_rom_boot(bp, port, + ext_phy_addr[port], shmem_base); + + bnx2x_cl45_read(bp, port, PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER1, &fw_ver1); + if (fw_ver1 == 0 || fw_ver1 == 0x4321) { + DP(NETIF_MSG_LINK, + "bnx2x_8073_common_init_phy port %x:" + "Download failed. fw version = 0x%x\n", + port, fw_ver1); + return -EINVAL; + } + + /* Only set bit 10 = 1 (Tx power down) */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, &val); + + /* Phase1 of TX_POWER_DOWN reset */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, + (val | 1<<10)); + } + + /* Toggle Transmitter: Power down and then up with 600ms + delay between */ + msleep(600); + + /* PART3 - complete TX_POWER_DOWN process, and set GPIO2 back to low */ + for (port = PORT_MAX - 1; port >= PORT_0; port--) { + /* Phase2 of POWER_DOWN_RESET */ + /* Release bit 10 (Release Tx power down) */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, &val); + + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10)))); + msleep(15); + + /* Read modify write the SPI-ROM version select register */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_EDC_FFE_MAIN, &val); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12))); + + /* set GPIO2 back to LOW */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); + } + return 0; + +} + +static u8 bnx2x_8727_common_init_phy(struct bnx2x *bp, u32 shmem_base) +{ + u8 ext_phy_addr[PORT_MAX]; + s8 port, first_port, i; + u32 swap_val, swap_override; + DP(NETIF_MSG_LINK, "Executing BCM8727 common init\n"); + swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); + swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); + + bnx2x_ext_phy_hw_reset(bp, 1 ^ (swap_val && swap_override)); + msleep(5); + + if (swap_val && swap_override) + first_port = PORT_0; + else + first_port = PORT_1; + + /* PART1 - Reset both phys */ + for (i = 0, port = first_port; i < PORT_MAX; i++, port = !port) { + /* Extract the ext phy address for the port */ + u32 ext_phy_config = REG_RD(bp, shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[port].external_phy_config)); + + /* disable attentions */ + bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, + (NIG_MASK_XGXS0_LINK_STATUS | + NIG_MASK_XGXS0_LINK10G | + NIG_MASK_SERDES0_LINK_STATUS | + NIG_MASK_MI_INT)); + + ext_phy_addr[port] = XGXS_EXT_PHY_ADDR(ext_phy_config); + + /* Reset the phy */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 1<<15); + } + + /* Add delay of 150ms after reset */ + msleep(150); + + /* PART2 - Download firmware to both phys */ + for (i = 0, port = first_port; i < PORT_MAX; i++, port = !port) { + u16 fw_ver1; + + bnx2x_bcm8727_external_rom_boot(bp, port, + ext_phy_addr[port], shmem_base); + + bnx2x_cl45_read(bp, port, PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER1, &fw_ver1); + if (fw_ver1 == 0 || fw_ver1 == 0x4321) { + DP(NETIF_MSG_LINK, + "bnx2x_8727_common_init_phy port %x:" + "Download failed. fw version = 0x%x\n", + port, fw_ver1); + return -EINVAL; + } + } + + return 0; +} + + +static u8 bnx2x_8726_common_init_phy(struct bnx2x *bp, u32 shmem_base) +{ + u8 ext_phy_addr; + u32 val; + s8 port; + + /* Use port1 because of the static port-swap */ + /* Enable the module detection interrupt */ + val = REG_RD(bp, MISC_REG_GPIO_EVENT_EN); + val |= ((1<<MISC_REGISTERS_GPIO_3)| + (1<<(MISC_REGISTERS_GPIO_3 + MISC_REGISTERS_GPIO_PORT_SHIFT))); + REG_WR(bp, MISC_REG_GPIO_EVENT_EN, val); + + bnx2x_ext_phy_hw_reset(bp, 1); + msleep(5); + for (port = 0; port < PORT_MAX; port++) { + /* Extract the ext phy address for the port */ + u32 ext_phy_config = REG_RD(bp, shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[port].external_phy_config)); + + ext_phy_addr = XGXS_EXT_PHY_ADDR(ext_phy_config); + DP(NETIF_MSG_LINK, "8726_common_init : ext_phy_addr = 0x%x\n", + ext_phy_addr); + + bnx2x_8726_reset_phy(bp, port, ext_phy_addr); + + /* Set fault module detected LED on */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, + MISC_REGISTERS_GPIO_HIGH, + port); + } + + return 0; +} + + +static u8 bnx2x_84823_common_init_phy(struct bnx2x *bp, u32 shmem_base) +{ + /* HW reset */ + bnx2x_ext_phy_hw_reset(bp, 1); + return 0; +} +u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base) +{ + u8 rc = 0; + u32 ext_phy_type; + + DP(NETIF_MSG_LINK, "Begin common phy init\n"); + + /* Read the ext_phy_type for arbitrary port(0) */ + ext_phy_type = XGXS_EXT_PHY_TYPE( + REG_RD(bp, shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[0].external_phy_config))); + + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: + { + rc = bnx2x_8073_common_init_phy(bp, shmem_base); + break; + } + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC: + rc = bnx2x_8727_common_init_phy(bp, shmem_base); + break; + + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: + /* GPIO1 affects both ports, so there's need to pull + it for single port alone */ + rc = bnx2x_8726_common_init_phy(bp, shmem_base); + break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823: + rc = bnx2x_84823_common_init_phy(bp, shmem_base); + break; + default: + DP(NETIF_MSG_LINK, + "bnx2x_common_init_phy: ext_phy 0x%x not required\n", + ext_phy_type); + break; + } + + return rc; +} + +void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, u8 port, u8 phy_addr) +{ + u16 val, cnt; + + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101, + phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_7101_RESET, &val); + + for (cnt = 0; cnt < 10; cnt++) { + msleep(50); + /* Writes a self-clearing reset */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101, + phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_7101_RESET, + (val | (1<<15))); + /* Wait for clear */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101, + phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_7101_RESET, &val); + + if ((val & (1<<15)) == 0) + break; + } +} |
