summaryrefslogtreecommitdiffstats
path: root/drivers/net/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/Kconfig')
-rw-r--r--drivers/net/Kconfig102
1 files changed, 81 insertions, 21 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index c748b0e..6d4f9ce 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -475,6 +475,14 @@ config SGI_IOC3_ETH_HW_TX_CSUM
the moment only acceleration of IPv4 is supported. This option
enables offloading for checksums on transmit. If unsure, say Y.
+config MIPS_SIM_NET
+ tristate "MIPS simulator Network device (EXPERIMENTAL)"
+ depends on NETDEVICES && MIPS_SIM && EXPERIMENTAL
+ help
+ The MIPSNET device is a simple Ethernet network device which is
+ emulated by the MIPS Simulator.
+ If you are not using a MIPSsim or are unsure, say N.
+
config SGI_O2MACE_ETH
tristate "SGI O2 MACE Fast Ethernet support"
depends on NET_ETHERNET && SGI_IP32=y
@@ -1155,38 +1163,74 @@ config IBMVETH
be called ibmveth.
config IBM_EMAC
- bool "IBM PPC4xx EMAC driver support"
+ tristate "PowerPC 4xx on-chip Ethernet support"
depends on 4xx
- select CRC32
- ---help---
- This driver supports the IBM PPC4xx EMAC family of on-chip
- Ethernet controllers.
-
-config IBM_EMAC_ERRMSG
- bool "Verbose error messages"
- depends on IBM_EMAC && BROKEN
+ help
+ This driver supports the PowerPC 4xx EMAC family of on-chip
+ Ethernet controllers.
config IBM_EMAC_RXB
int "Number of receive buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "64"
+ default "128"
config IBM_EMAC_TXB
int "Number of transmit buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "8"
+ default "64"
+
+config IBM_EMAC_POLL_WEIGHT
+ int "MAL NAPI polling weight"
+ depends on IBM_EMAC
+ default "32"
-config IBM_EMAC_FGAP
- int "Frame gap"
+config IBM_EMAC_RX_COPY_THRESHOLD
+ int "RX skb copy threshold (bytes)"
depends on IBM_EMAC
- default "8"
+ default "256"
-config IBM_EMAC_SKBRES
- int "Skb reserve amount"
+config IBM_EMAC_RX_SKB_HEADROOM
+ int "Additional RX skb headroom (bytes)"
depends on IBM_EMAC
default "0"
+ help
+ Additional receive skb headroom. Note, that driver
+ will always reserve at least 2 bytes to make IP header
+ aligned, so usualy there is no need to add any additional
+ headroom.
+
+ If unsure, set to 0.
+
+config IBM_EMAC_PHY_RX_CLK_FIX
+ bool "PHY Rx clock workaround"
+ depends on IBM_EMAC && (405EP || 440GX || 440EP)
+ help
+ Enable this if EMAC attached to a PHY which doesn't generate
+ RX clock if there is no link, if this is the case, you will
+ see "TX disable timeout" or "RX disable timeout" in the system
+ log.
+
+ If unsure, say N.
+
+config IBM_EMAC_DEBUG
+ bool "Debugging"
+ depends on IBM_EMAC
+ default n
+
+config IBM_EMAC_ZMII
+ bool
+ depends on IBM_EMAC && (NP405H || NP405L || 44x)
+ default y
+
+config IBM_EMAC_RGMII
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
+
+config IBM_EMAC_TAH
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
@@ -1330,7 +1374,7 @@ config FORCEDETH
config CS89x0
tristate "CS89x0 support"
- depends on (NET_PCI && (ISA || ARCH_IXDP2X01)) || ARCH_PNX0105
+ depends on (NET_PCI && (ISA || ARCH_IXDP2X01)) || ARCH_PNX0105 || MACH_MP1000
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
network (Ethernet) card of this type, say Y and read the
@@ -1767,6 +1811,7 @@ config NE_H8300
controller on the Renesas H8/300 processor.
source "drivers/net/fec_8xx/Kconfig"
+source "drivers/net/fs_enet/Kconfig"
endmenu
@@ -2083,6 +2128,7 @@ config SPIDER_NET
config GIANFAR
tristate "Gianfar Ethernet"
depends on 85xx || 83xx
+ select PHYLIB
help
This driver supports the Gigabit TSEC on the MPC85xx
family of chips, and the FEC on the 8540
@@ -2192,8 +2238,8 @@ config S2IO
depends on PCI
---help---
This driver supports the 10Gbe XFrame NIC of S2IO.
- For help regarding driver compilation, installation and
- tuning please look into ~/drivers/net/s2io/README.txt.
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/s2io.txt>.
config S2IO_NAPI
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
@@ -2243,6 +2289,20 @@ config ISERIES_VETH
tristate "iSeries Virtual Ethernet driver support"
depends on PPC_ISERIES
+config RIONET
+ tristate "RapidIO Ethernet over messaging driver support"
+ depends on NETDEVICES && RAPIDIO
+
+config RIONET_TX_SIZE
+ int "Number of outbound queue entries"
+ depends on RIONET
+ default "128"
+
+config RIONET_RX_SIZE
+ int "Number of inbound queue entries"
+ depends on RIONET
+ default "128"
+
config FDDI
bool "FDDI driver support"
depends on (PCI || EISA)
OpenPOWER on IntegriCloud