diff options
Diffstat (limited to 'drivers/mtd/nand/raw/r852.h')
| -rw-r--r-- | drivers/mtd/nand/raw/r852.h | 157 |
1 files changed, 157 insertions, 0 deletions
diff --git a/drivers/mtd/nand/raw/r852.h b/drivers/mtd/nand/raw/r852.h new file mode 100644 index 0000000..1eed2fc --- /dev/null +++ b/drivers/mtd/nand/raw/r852.h @@ -0,0 +1,157 @@ +/* + * Copyright © 2009 - Maxim Levitsky + * driver for Ricoh xD readers + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/pci.h> +#include <linux/completion.h> +#include <linux/workqueue.h> +#include <linux/mtd/rawnand.h> +#include <linux/spinlock.h> + + +/* nand interface + ecc + byte write/read does one cycle on nand data lines. + dword write/read does 4 cycles + if R852_CTL_ECC_ACCESS is set in R852_CTL, then dword read reads + results of ecc correction, if DMA read was done before. + If write was done two dword reads read generated ecc checksums +*/ +#define R852_DATALINE 0x00 + +/* control register */ +#define R852_CTL 0x04 +#define R852_CTL_COMMAND 0x01 /* send command (#CLE)*/ +#define R852_CTL_DATA 0x02 /* read/write data (#ALE)*/ +#define R852_CTL_ON 0x04 /* only seem to controls the hd led, */ + /* but has to be set on start...*/ +#define R852_CTL_RESET 0x08 /* unknown, set only on start once*/ +#define R852_CTL_CARDENABLE 0x10 /* probably (#CE) - always set*/ +#define R852_CTL_ECC_ENABLE 0x20 /* enable ecc engine */ +#define R852_CTL_ECC_ACCESS 0x40 /* read/write ecc via reg #0*/ +#define R852_CTL_WRITE 0x80 /* set when performing writes (#WP) */ + +/* card detection status */ +#define R852_CARD_STA 0x05 + +#define R852_CARD_STA_CD 0x01 /* state of #CD line, same as 0x04 */ +#define R852_CARD_STA_RO 0x02 /* card is readonly */ +#define R852_CARD_STA_PRESENT 0x04 /* card is present (#CD) */ +#define R852_CARD_STA_ABSENT 0x08 /* card is absent */ +#define R852_CARD_STA_BUSY 0x80 /* card is busy - (#R/B) */ + +/* card detection irq status & enable*/ +#define R852_CARD_IRQ_STA 0x06 /* IRQ status */ +#define R852_CARD_IRQ_ENABLE 0x07 /* IRQ enable */ + +#define R852_CARD_IRQ_CD 0x01 /* fire when #CD lights, same as 0x04*/ +#define R852_CARD_IRQ_REMOVE 0x04 /* detect card removal */ +#define R852_CARD_IRQ_INSERT 0x08 /* detect card insert */ +#define R852_CARD_IRQ_UNK1 0x10 /* unknown */ +#define R852_CARD_IRQ_GENABLE 0x80 /* general enable */ +#define R852_CARD_IRQ_MASK 0x1D + + + +/* hardware enable */ +#define R852_HW 0x08 +#define R852_HW_ENABLED 0x01 /* hw enabled */ +#define R852_HW_UNKNOWN 0x80 + + +/* dma capabilities */ +#define R852_DMA_CAP 0x09 +#define R852_SMBIT 0x20 /* if set with bit #6 or bit #7, then */ + /* hw is smartmedia */ +#define R852_DMA1 0x40 /* if set w/bit #7, dma is supported */ +#define R852_DMA2 0x80 /* if set w/bit #6, dma is supported */ + + +/* physical DMA address - 32 bit value*/ +#define R852_DMA_ADDR 0x0C + + +/* dma settings */ +#define R852_DMA_SETTINGS 0x10 +#define R852_DMA_MEMORY 0x01 /* (memory <-> internal hw buffer) */ +#define R852_DMA_READ 0x02 /* 0 = write, 1 = read */ +#define R852_DMA_INTERNAL 0x04 /* (internal hw buffer <-> card) */ + +/* dma IRQ status */ +#define R852_DMA_IRQ_STA 0x14 + +/* dma IRQ enable */ +#define R852_DMA_IRQ_ENABLE 0x18 + +#define R852_DMA_IRQ_MEMORY 0x01 /* (memory <-> internal hw buffer) */ +#define R852_DMA_IRQ_ERROR 0x02 /* error did happen */ +#define R852_DMA_IRQ_INTERNAL 0x04 /* (internal hw buffer <-> card) */ +#define R852_DMA_IRQ_MASK 0x07 /* mask of all IRQ bits */ + + +/* ECC syndrome format - read from reg #0 will return two copies of these for + each half of the page. + first byte is error byte location, and second, bit location + flags */ +#define R852_ECC_ERR_BIT_MSK 0x07 /* error bit location */ +#define R852_ECC_CORRECT 0x10 /* no errors - (guessed) */ +#define R852_ECC_CORRECTABLE 0x20 /* correctable error exist */ +#define R852_ECC_FAIL 0x40 /* non correctable error detected */ + +#define R852_DMA_LEN 512 + +#define DMA_INTERNAL 0 +#define DMA_MEMORY 1 + +struct r852_device { + void __iomem *mmio; /* mmio */ + struct nand_chip *chip; /* nand chip backpointer */ + struct pci_dev *pci_dev; /* pci backpointer */ + + /* dma area */ + dma_addr_t phys_dma_addr; /* bus address of buffer*/ + struct completion dma_done; /* data transfer done */ + + dma_addr_t phys_bounce_buffer; /* bus address of bounce buffer */ + uint8_t *bounce_buffer; /* virtual address of bounce buffer */ + + int dma_dir; /* 1 = read, 0 = write */ + int dma_stage; /* 0 - idle, 1 - first step, + 2 - second step */ + + int dma_state; /* 0 = internal, 1 = memory */ + int dma_error; /* dma errors */ + int dma_usable; /* is it possible to use dma */ + + /* card status area */ + struct delayed_work card_detect_work; + struct workqueue_struct *card_workqueue; + int card_registred; /* card registered with mtd */ + int card_detected; /* card detected in slot */ + int card_unstable; /* whenever the card is inserted, + is not known yet */ + int readonly; /* card is readonly */ + int sm; /* Is card smartmedia */ + + /* interrupt handling */ + spinlock_t irqlock; /* IRQ protecting lock */ + int irq; /* irq num */ + /* misc */ + void *tmp_buffer; /* temporary buffer */ + uint8_t ctlreg; /* cached contents of control reg */ +}; + +#define dbg(format, ...) \ + if (debug) \ + pr_debug(format "\n", ## __VA_ARGS__) + +#define dbg_verbose(format, ...) \ + if (debug > 1) \ + pr_debug(format "\n", ## __VA_ARGS__) + + +#define message(format, ...) \ + pr_info(format "\n", ## __VA_ARGS__) |
