diff options
Diffstat (limited to 'drivers/mmc/host')
| -rw-r--r-- | drivers/mmc/host/atmel-mci.c | 4 | ||||
| -rw-r--r-- | drivers/mmc/host/mmc_spi.c | 2 | ||||
| -rw-r--r-- | drivers/mmc/host/s3cmci.c | 6 | ||||
| -rw-r--r-- | drivers/mmc/host/tmio_mmc_pio.c | 2 | ||||
| -rw-r--r-- | drivers/mmc/host/wbsd.c | 6 |
5 files changed, 10 insertions, 10 deletions
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c index 80bc9a5..ea3888b 100644 --- a/drivers/mmc/host/atmel-mci.c +++ b/drivers/mmc/host/atmel-mci.c @@ -127,7 +127,7 @@ struct atmel_mci_dma { * EVENT_DATA_COMPLETE is set in @pending_events, all data-related * interrupts must be disabled and @data_status updated with a * snapshot of SR. Similarly, before EVENT_CMD_COMPLETE is set, the - * CMDRDY interupt must be disabled and @cmd_status updated with a + * CMDRDY interrupt must be disabled and @cmd_status updated with a * snapshot of SR, and before EVENT_XFER_COMPLETE can be set, the * bytes_xfered field of @data must be written. This is ensured by * using barriers. @@ -1082,7 +1082,7 @@ static void atmci_request_end(struct atmel_mci *host, struct mmc_request *mrq) /* * Update the MMC clock rate if necessary. This may be * necessary if set_ios() is called when a different slot is - * busy transfering data. + * busy transferring data. */ if (host->need_clock_update) { mci_writel(host, MR, host->mode_reg); diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c index 2f7fc0c..7c1e16a 100644 --- a/drivers/mmc/host/mmc_spi.c +++ b/drivers/mmc/host/mmc_spi.c @@ -99,7 +99,7 @@ #define r1b_timeout (HZ * 3) /* One of the critical speed parameters is the amount of data which may - * be transfered in one command. If this value is too low, the SD card + * be transferred in one command. If this value is too low, the SD card * controller has to do multiple partial block writes (argggh!). With * today (2008) SD cards there is little speed gain if we transfer more * than 64 KBytes at a time. So use this value until there is any indication diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 1ccd4b2..a04f87d 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -874,7 +874,7 @@ static void finalize_request(struct s3cmci_host *host) if (!mrq->data) goto request_done; - /* Calulate the amout of bytes transfer if there was no error */ + /* Calculate the amout of bytes transfer if there was no error */ if (mrq->data->error == 0) { mrq->data->bytes_xfered = (mrq->data->blocks * mrq->data->blksz); @@ -882,7 +882,7 @@ static void finalize_request(struct s3cmci_host *host) mrq->data->bytes_xfered = 0; } - /* If we had an error while transfering data we flush the + /* If we had an error while transferring data we flush the * DMA channel and the fifo to clear out any garbage. */ if (mrq->data->error != 0) { if (s3cmci_host_usedma(host)) @@ -980,7 +980,7 @@ static int s3cmci_setup_data(struct s3cmci_host *host, struct mmc_data *data) if ((data->blksz & 3) != 0) { /* We cannot deal with unaligned blocks with more than - * one block being transfered. */ + * one block being transferred. */ if (data->blocks > 1) { pr_warning("%s: can't do non-word sized block transfers (blksz %d)\n", __func__, data->blksz); diff --git a/drivers/mmc/host/tmio_mmc_pio.c b/drivers/mmc/host/tmio_mmc_pio.c index 6ae8d2f..62d37de 100644 --- a/drivers/mmc/host/tmio_mmc_pio.c +++ b/drivers/mmc/host/tmio_mmc_pio.c @@ -355,7 +355,7 @@ static int tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command /* * This chip always returns (at least?) as much data as you ask for. * I'm unsure what happens if you ask for less than a block. This should be - * looked into to ensure that a funny length read doesnt hose the controller. + * looked into to ensure that a funny length read doesn't hose the controller. */ static void tmio_mmc_pio_irq(struct tmio_mmc_host *host) { diff --git a/drivers/mmc/host/wbsd.c b/drivers/mmc/host/wbsd.c index 7fca0a3..62e5a4d 100644 --- a/drivers/mmc/host/wbsd.c +++ b/drivers/mmc/host/wbsd.c @@ -484,7 +484,7 @@ static void wbsd_fill_fifo(struct wbsd_host *host) /* * Check that we aren't being called after the - * entire buffer has been transfered. + * entire buffer has been transferred. */ if (host->num_sg == 0) return; @@ -828,7 +828,7 @@ static void wbsd_request(struct mmc_host *mmc, struct mmc_request *mrq) /* * If this is a data transfer the request * will be finished after the data has - * transfered. + * transferred. */ if (cmd->data && !cmd->error) { /* @@ -904,7 +904,7 @@ static void wbsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) setup &= ~WBSD_DAT3_H; /* - * We cannot resume card detection immediatly + * We cannot resume card detection immediately * because of capacitance and delays in the chip. */ mod_timer(&host->ignore_timer, jiffies + HZ / 100); |
