diff options
Diffstat (limited to 'drivers/mmc/host/au1xmmc.c')
| -rw-r--r-- | drivers/mmc/host/au1xmmc.c | 1031 |
1 files changed, 1031 insertions, 0 deletions
diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c new file mode 100644 index 0000000..b7156a4 --- /dev/null +++ b/drivers/mmc/host/au1xmmc.c @@ -0,0 +1,1031 @@ +/* + * linux/drivers/mmc/au1xmmc.c - AU1XX0 MMC driver + * + * Copyright (c) 2005, Advanced Micro Devices, Inc. + * + * Developed with help from the 2.4.30 MMC AU1XXX controller including + * the following copyright notices: + * Copyright (c) 2003-2004 Embedded Edge, LLC. + * Portions Copyright (C) 2002 Embedix, Inc + * Copyright 2002 Hewlett-Packard Company + + * 2.6 version of this driver inspired by: + * (drivers/mmc/wbsd.c) Copyright (C) 2004-2005 Pierre Ossman, + * All Rights Reserved. + * (drivers/mmc/pxa.c) Copyright (C) 2003 Russell King, + * All Rights Reserved. + * + + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* Why is a timer used to detect insert events? + * + * From the AU1100 MMC application guide: + * If the Au1100-based design is intended to support both MultiMediaCards + * and 1- or 4-data bit SecureDigital cards, then the solution is to + * connect a weak (560KOhm) pull-up resistor to connector pin 1. + * In doing so, a MMC card never enters SPI-mode communications, + * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective + * (the low to high transition will not occur). + * + * So we use the timer to check the status manually. + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/mm.h> +#include <linux/interrupt.h> +#include <linux/dma-mapping.h> + +#include <linux/mmc/host.h> +#include <asm/io.h> +#include <asm/mach-au1x00/au1000.h> +#include <asm/mach-au1x00/au1xxx_dbdma.h> +#include <asm/mach-au1x00/au1100_mmc.h> +#include <asm/scatterlist.h> + +#include <au1xxx.h> +#include "au1xmmc.h" + +#define DRIVER_NAME "au1xxx-mmc" + +/* Set this to enable special debugging macros */ + +#ifdef DEBUG +#define DBG(fmt, idx, args...) printk("au1xx(%d): DEBUG: " fmt, idx, ##args) +#else +#define DBG(fmt, idx, args...) +#endif + +const struct { + u32 iobase; + u32 tx_devid, rx_devid; + u16 bcsrpwr; + u16 bcsrstatus; + u16 wpstatus; +} au1xmmc_card_table[] = { + { SD0_BASE, DSCR_CMD0_SDMS_TX0, DSCR_CMD0_SDMS_RX0, + BCSR_BOARD_SD0PWR, BCSR_INT_SD0INSERT, BCSR_STATUS_SD0WP }, +#ifndef CONFIG_MIPS_DB1200 + { SD1_BASE, DSCR_CMD0_SDMS_TX1, DSCR_CMD0_SDMS_RX1, + BCSR_BOARD_DS1PWR, BCSR_INT_SD1INSERT, BCSR_STATUS_SD1WP } +#endif +}; + +#define AU1XMMC_CONTROLLER_COUNT \ + (sizeof(au1xmmc_card_table) / sizeof(au1xmmc_card_table[0])) + +/* This array stores pointers for the hosts (used by the IRQ handler) */ +struct au1xmmc_host *au1xmmc_hosts[AU1XMMC_CONTROLLER_COUNT]; +static int dma = 1; + +#ifdef MODULE +module_param(dma, bool, 0); +MODULE_PARM_DESC(dma, "Use DMA engine for data transfers (0 = disabled)"); +#endif + +static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask) +{ + u32 val = au_readl(HOST_CONFIG(host)); + val |= mask; + au_writel(val, HOST_CONFIG(host)); + au_sync(); +} + +static inline void FLUSH_FIFO(struct au1xmmc_host *host) +{ + u32 val = au_readl(HOST_CONFIG2(host)); + + au_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host)); + au_sync_delay(1); + + /* SEND_STOP will turn off clock control - this re-enables it */ + val &= ~SD_CONFIG2_DF; + + au_writel(val, HOST_CONFIG2(host)); + au_sync(); +} + +static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask) +{ + u32 val = au_readl(HOST_CONFIG(host)); + val &= ~mask; + au_writel(val, HOST_CONFIG(host)); + au_sync(); +} + +static inline void SEND_STOP(struct au1xmmc_host *host) +{ + + /* We know the value of CONFIG2, so avoid a read we don't need */ + u32 mask = SD_CONFIG2_EN; + + WARN_ON(host->status != HOST_S_DATA); + host->status = HOST_S_STOP; + + au_writel(mask | SD_CONFIG2_DF, HOST_CONFIG2(host)); + au_sync(); + + /* Send the stop commmand */ + au_writel(STOP_CMD, HOST_CMD(host)); +} + +static void au1xmmc_set_power(struct au1xmmc_host *host, int state) +{ + + u32 val = au1xmmc_card_table[host->id].bcsrpwr; + + bcsr->board &= ~val; + if (state) bcsr->board |= val; + + au_sync_delay(1); +} + +static inline int au1xmmc_card_inserted(struct au1xmmc_host *host) +{ + return (bcsr->sig_status & au1xmmc_card_table[host->id].bcsrstatus) + ? 1 : 0; +} + +static int au1xmmc_card_readonly(struct mmc_host *mmc) +{ + struct au1xmmc_host *host = mmc_priv(mmc); + return (bcsr->status & au1xmmc_card_table[host->id].wpstatus) + ? 1 : 0; +} + +static void au1xmmc_finish_request(struct au1xmmc_host *host) +{ + + struct mmc_request *mrq = host->mrq; + + host->mrq = NULL; + host->flags &= HOST_F_ACTIVE; + + host->dma.len = 0; + host->dma.dir = 0; + + host->pio.index = 0; + host->pio.offset = 0; + host->pio.len = 0; + + host->status = HOST_S_IDLE; + + bcsr->disk_leds |= (1 << 8); + + mmc_request_done(host->mmc, mrq); +} + +static void au1xmmc_tasklet_finish(unsigned long param) +{ + struct au1xmmc_host *host = (struct au1xmmc_host *) param; + au1xmmc_finish_request(host); +} + +static int au1xmmc_send_command(struct au1xmmc_host *host, int wait, + struct mmc_command *cmd) +{ + + u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT); + + switch (mmc_resp_type(cmd)) { + case MMC_RSP_NONE: + break; + case MMC_RSP_R1: + mmccmd |= SD_CMD_RT_1; + break; + case MMC_RSP_R1B: + mmccmd |= SD_CMD_RT_1B; + break; + case MMC_RSP_R2: + mmccmd |= SD_CMD_RT_2; + break; + case MMC_RSP_R3: + mmccmd |= SD_CMD_RT_3; + break; + default: + printk(KERN_INFO "au1xmmc: unhandled response type %02x\n", + mmc_resp_type(cmd)); + return MMC_ERR_INVALID; + } + + switch(cmd->opcode) { + case MMC_READ_SINGLE_BLOCK: + case SD_APP_SEND_SCR: + mmccmd |= SD_CMD_CT_2; + break; + case MMC_READ_MULTIPLE_BLOCK: + mmccmd |= SD_CMD_CT_4; + break; + case MMC_WRITE_BLOCK: + mmccmd |= SD_CMD_CT_1; + break; + + case MMC_WRITE_MULTIPLE_BLOCK: + mmccmd |= SD_CMD_CT_3; + break; + case MMC_STOP_TRANSMISSION: + mmccmd |= SD_CMD_CT_7; + break; + } + + au_writel(cmd->arg, HOST_CMDARG(host)); + au_sync(); + + if (wait) + IRQ_OFF(host, SD_CONFIG_CR); + + au_writel((mmccmd | SD_CMD_GO), HOST_CMD(host)); + au_sync(); + + /* Wait for the command to go on the line */ + + while(1) { + if (!(au_readl(HOST_CMD(host)) & SD_CMD_GO)) + break; + } + + /* Wait for the command to come back */ + + if (wait) { + u32 status = au_readl(HOST_STATUS(host)); + + while(!(status & SD_STATUS_CR)) + status = au_readl(HOST_STATUS(host)); + + /* Clear the CR status */ + au_writel(SD_STATUS_CR, HOST_STATUS(host)); + + IRQ_ON(host, SD_CONFIG_CR); + } + + return MMC_ERR_NONE; +} + +static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) +{ + + struct mmc_request *mrq = host->mrq; + struct mmc_data *data; + u32 crc; + + WARN_ON(host->status != HOST_S_DATA && host->status != HOST_S_STOP); + + if (host->mrq == NULL) + return; + + data = mrq->cmd->data; + + if (status == 0) + status = au_readl(HOST_STATUS(host)); + + /* The transaction is really over when the SD_STATUS_DB bit is clear */ + + while((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB)) + status = au_readl(HOST_STATUS(host)); + + data->error = MMC_ERR_NONE; + dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir); + + /* Process any errors */ + + crc = (status & (SD_STATUS_WC | SD_STATUS_RC)); + if (host->flags & HOST_F_XMIT) + crc |= ((status & 0x07) == 0x02) ? 0 : 1; + + if (crc) + data->error = MMC_ERR_BADCRC; + + /* Clear the CRC bits */ + au_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host)); + + data->bytes_xfered = 0; + + if (data->error == MMC_ERR_NONE) { + if (host->flags & HOST_F_DMA) { + u32 chan = DMA_CHANNEL(host); + + chan_tab_t *c = *((chan_tab_t **) chan); + au1x_dma_chan_t *cp = c->chan_ptr; + data->bytes_xfered = cp->ddma_bytecnt; + } + else + data->bytes_xfered = + (data->blocks * data->blksz) - + host->pio.len; + } + + au1xmmc_finish_request(host); +} + +static void au1xmmc_tasklet_data(unsigned long param) +{ + struct au1xmmc_host *host = (struct au1xmmc_host *) param; + + u32 status = au_readl(HOST_STATUS(host)); + au1xmmc_data_complete(host, status); +} + +#define AU1XMMC_MAX_TRANSFER 8 + +static void au1xmmc_send_pio(struct au1xmmc_host *host) +{ + + struct mmc_data *data = 0; + int sg_len, max, count = 0; + unsigned char *sg_ptr; + u32 status = 0; + struct scatterlist *sg; + + data = host->mrq->data; + + if (!(host->flags & HOST_F_XMIT)) + return; + + /* This is the pointer to the data buffer */ + sg = &data->sg[host->pio.index]; + sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset; + + /* This is the space left inside the buffer */ + sg_len = data->sg[host->pio.index].length - host->pio.offset; + + /* Check to if we need less then the size of the sg_buffer */ + + max = (sg_len > host->pio.len) ? host->pio.len : sg_len; + if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER; + + for(count = 0; count < max; count++ ) { + unsigned char val; + + status = au_readl(HOST_STATUS(host)); + + if (!(status & SD_STATUS_TH)) + break; + + val = *sg_ptr++; + + au_writel((unsigned long) val, HOST_TXPORT(host)); + au_sync(); + } + + host->pio.len -= count; + host->pio.offset += count; + + if (count == sg_len) { + host->pio.index++; + host->pio.offset = 0; + } + + if (host->pio.len == 0) { + IRQ_OFF(host, SD_CONFIG_TH); + + if (host->flags & HOST_F_STOP) + SEND_STOP(host); + + tasklet_schedule(&host->data_task); + } +} + +static void au1xmmc_receive_pio(struct au1xmmc_host *host) +{ + + struct mmc_data *data = 0; + int sg_len = 0, max = 0, count = 0; + unsigned char *sg_ptr = 0; + u32 status = 0; + struct scatterlist *sg; + + data = host->mrq->data; + + if (!(host->flags & HOST_F_RECV)) + return; + + max = host->pio.len; + + if (host->pio.index < host->dma.len) { + sg = &data->sg[host->pio.index]; + sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset; + + /* This is the space left inside the buffer */ + sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset; + + /* Check to if we need less then the size of the sg_buffer */ + if (sg_len < max) max = sg_len; + } + + if (max > AU1XMMC_MAX_TRANSFER) + max = AU1XMMC_MAX_TRANSFER; + + for(count = 0; count < max; count++ ) { + u32 val; + status = au_readl(HOST_STATUS(host)); + + if (!(status & SD_STATUS_NE)) + break; + + if (status & SD_STATUS_RC) { + DBG("RX CRC Error [%d + %d].\n", host->id, + host->pio.len, count); + break; + } + + if (status & SD_STATUS_RO) { + DBG("RX Overrun [%d + %d]\n", host->id, + host->pio.len, count); + break; + } + else if (status & SD_STATUS_RU) { + DBG("RX Underrun [%d + %d]\n", host->id, + host->pio.len, count); + break; + } + + val = au_readl(HOST_RXPORT(host)); + + if (sg_ptr) + *sg_ptr++ = (unsigned char) (val & 0xFF); + } + + host->pio.len -= count; + host->pio.offset += count; + + if (sg_len && count == sg_len) { + host->pio.index++; + host->pio.offset = 0; + } + + if (host->pio.len == 0) { + //IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF); + IRQ_OFF(host, SD_CONFIG_NE); + + if (host->flags & HOST_F_STOP) + SEND_STOP(host); + + tasklet_schedule(&host->data_task); + } +} + +/* static void au1xmmc_cmd_complete + This is called when a command has been completed - grab the response + and check for errors. Then start the data transfer if it is indicated. +*/ + +static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) +{ + + struct mmc_request *mrq = host->mrq; + struct mmc_command *cmd; + int trans; + + if (!host->mrq) + return; + + cmd = mrq->cmd; + cmd->error = MMC_ERR_NONE; + + if (cmd->flags & MMC_RSP_PRESENT) { + if (cmd->flags & MMC_RSP_136) { + u32 r[4]; + int i; + + r[0] = au_readl(host->iobase + SD_RESP3); + r[1] = au_readl(host->iobase + SD_RESP2); + r[2] = au_readl(host->iobase + SD_RESP1); + r[3] = au_readl(host->iobase + SD_RESP0); + + /* The CRC is omitted from the response, so really + * we only got 120 bytes, but the engine expects + * 128 bits, so we have to shift things up + */ + + for(i = 0; i < 4; i++) { + cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8; + if (i != 3) + cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24; + } + } else { + /* Techincally, we should be getting all 48 bits of + * the response (SD_RESP1 + SD_RESP2), but because + * our response omits the CRC, our data ends up + * being shifted 8 bits to the right. In this case, + * that means that the OSR data starts at bit 31, + * so we can just read RESP0 and return that + */ + cmd->resp[0] = au_readl(host->iobase + SD_RESP0); + } + } + + /* Figure out errors */ + + if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC)) + cmd->error = MMC_ERR_BADCRC; + + trans = host->flags & (HOST_F_XMIT | HOST_F_RECV); + + if (!trans || cmd->error != MMC_ERR_NONE) { + + IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA|SD_CONFIG_RF); + tasklet_schedule(&host->finish_task); + return; + } + + host->status = HOST_S_DATA; + + if (host->flags & HOST_F_DMA) { + u32 channel = DMA_CHANNEL(host); + + /* Start the DMA as soon as the buffer gets something in it */ + + if (host->flags & HOST_F_RECV) { + u32 mask = SD_STATUS_DB | SD_STATUS_NE; + + while((status & mask) != mask) + status = au_readl(HOST_STATUS(host)); + } + + au1xxx_dbdma_start(channel); + } +} + +static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate) +{ + + unsigned int pbus = get_au1x00_speed(); + unsigned int divisor; + u32 config; + + /* From databook: + divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1 + */ + + pbus /= ((au_readl(SYS_POWERCTRL) & 0x3) + 2); + pbus /= 2; + + divisor = ((pbus / rate) / 2) - 1; + + config = au_readl(HOST_CONFIG(host)); + + config &= ~(SD_CONFIG_DIV); + config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE; + + au_writel(config, HOST_CONFIG(host)); + au_sync(); +} + +static int +au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) +{ + + int datalen = data->blocks * data->blksz; + + if (dma != 0) + host->flags |= HOST_F_DMA; + + if (data->flags & MMC_DATA_READ) + host->flags |= HOST_F_RECV; + else + host->flags |= HOST_F_XMIT; + + if (host->mrq->stop) + host->flags |= HOST_F_STOP; + + host->dma.dir = DMA_BIDIRECTIONAL; + + host->dma.len = dma_map_sg(mmc_dev(host->mmc), data->sg, + data->sg_len, host->dma.dir); + + if (host->dma.len == 0) + return MMC_ERR_TIMEOUT; + + au_writel(data->blksz - 1, HOST_BLKSIZE(host)); + + if (host->flags & HOST_F_DMA) { + int i; + u32 channel = DMA_CHANNEL(host); + + au1xxx_dbdma_stop(channel); + + for(i = 0; i < host->dma.len; i++) { + u32 ret = 0, flags = DDMA_FLAGS_NOIE; + struct scatterlist *sg = &data->sg[i]; + int sg_len = sg->length; + + int len = (datalen > sg_len) ? sg_len : datalen; + + if (i == host->dma.len - 1) + flags = DDMA_FLAGS_IE; + + if (host->flags & HOST_F_XMIT){ + ret = au1xxx_dbdma_put_source_flags(channel, + (void *) (page_address(sg->page) + + sg->offset), + len, flags); + } + else { + ret = au1xxx_dbdma_put_dest_flags(channel, + (void *) (page_address(sg->page) + + sg->offset), + len, flags); + } + + if (!ret) + goto dataerr; + + datalen -= len; + } + } + else { + host->pio.index = 0; + host->pio.offset = 0; + host->pio.len = datalen; + + if (host->flags & HOST_F_XMIT) + IRQ_ON(host, SD_CONFIG_TH); + else + IRQ_ON(host, SD_CONFIG_NE); + //IRQ_ON(host, SD_CONFIG_RA|SD_CONFIG_RF); + } + + return MMC_ERR_NONE; + + dataerr: + dma_unmap_sg(mmc_dev(host->mmc),data->sg,data->sg_len,host->dma.dir); + return MMC_ERR_TIMEOUT; +} + +/* static void au1xmmc_request + This actually starts a command or data transaction +*/ + +static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) +{ + + struct au1xmmc_host *host = mmc_priv(mmc); + int ret = MMC_ERR_NONE; + + WARN_ON(irqs_disabled()); + WARN_ON(host->status != HOST_S_IDLE); + + host->mrq = mrq; + host->status = HOST_S_CMD; + + bcsr->disk_leds &= ~(1 << 8); + + if (mrq->data) { + FLUSH_FIFO(host); + ret = au1xmmc_prepare_data(host, mrq->data); + } + + if (ret == MMC_ERR_NONE) + ret = au1xmmc_send_command(host, 0, mrq->cmd); + + if (ret != MMC_ERR_NONE) { + mrq->cmd->error = ret; + au1xmmc_finish_request(host); + } +} + +static void au1xmmc_reset_controller(struct au1xmmc_host *host) +{ + + /* Apply the clock */ + au_writel(SD_ENABLE_CE, HOST_ENABLE(host)); + au_sync_delay(1); + + au_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host)); + au_sync_delay(5); + + au_writel(~0, HOST_STATUS(host)); + au_sync(); + + au_writel(0, HOST_BLKSIZE(host)); + au_writel(0x001fffff, HOST_TIMEOUT(host)); + au_sync(); + + au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host)); + au_sync(); + + au_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host)); + au_sync_delay(1); + + au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host)); + au_sync(); + + /* Configure interrupts */ + au_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host)); + au_sync(); +} + + +static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios) +{ + struct au1xmmc_host *host = mmc_priv(mmc); + + if (ios->power_mode == MMC_POWER_OFF) + au1xmmc_set_power(host, 0); + else if (ios->power_mode == MMC_POWER_ON) { + au1xmmc_set_power(host, 1); + } + + if (ios->clock && ios->clock != host->clock) { + au1xmmc_set_clock(host, ios->clock); + host->clock = ios->clock; + } +} + +static void au1xmmc_dma_callback(int irq, void *dev_id) +{ + struct au1xmmc_host *host = (struct au1xmmc_host *) dev_id; + + /* Avoid spurious interrupts */ + + if (!host->mrq) + return; + + if (host->flags & HOST_F_STOP) + SEND_STOP(host); + + tasklet_schedule(&host->data_task); +} + +#define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT) +#define STATUS_DATA_IN (SD_STATUS_NE) +#define STATUS_DATA_OUT (SD_STATUS_TH) + +static irqreturn_t au1xmmc_irq(int irq, void *dev_id) +{ + + u32 status; + int i, ret = 0; + + disable_irq(AU1100_SD_IRQ); + + for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) { + struct au1xmmc_host * host = au1xmmc_hosts[i]; + u32 handled = 1; + + status = au_readl(HOST_STATUS(host)); + + if (host->mrq && (status & STATUS_TIMEOUT)) { + if (status & SD_STATUS_RAT) + host->mrq->cmd->error = MMC_ERR_TIMEOUT; + + else if (status & SD_STATUS_DT) + host->mrq->data->error = MMC_ERR_TIMEOUT; + + /* In PIO mode, interrupts might still be enabled */ + IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH); + + //IRQ_OFF(host, SD_CONFIG_TH|SD_CONFIG_RA|SD_CONFIG_RF); + tasklet_schedule(&host->finish_task); + } +#if 0 + else if (status & SD_STATUS_DD) { + + /* Sometimes we get a DD before a NE in PIO mode */ + + if (!(host->flags & HOST_F_DMA) && + (status & SD_STATUS_NE)) + au1xmmc_receive_pio(host); + else { + au1xmmc_data_complete(host, status); + //tasklet_schedule(&host->data_task); + } + } +#endif + else if (status & (SD_STATUS_CR)) { + if (host->status == HOST_S_CMD) + au1xmmc_cmd_complete(host,status); + } + else if (!(host->flags & HOST_F_DMA)) { + if ((host->flags & HOST_F_XMIT) && + (status & STATUS_DATA_OUT)) + au1xmmc_send_pio(host); + else if ((host->flags & HOST_F_RECV) && + (status & STATUS_DATA_IN)) + au1xmmc_receive_pio(host); + } + else if (status & 0x203FBC70) { + DBG("Unhandled status %8.8x\n", host->id, status); + handled = 0; + } + + au_writel(status, HOST_STATUS(host)); + au_sync(); + + ret |= handled; + } + + enable_irq(AU1100_SD_IRQ); + return ret; +} + +static void au1xmmc_poll_event(unsigned long arg) +{ + struct au1xmmc_host *host = (struct au1xmmc_host *) arg; + + int card = au1xmmc_card_inserted(host); + int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0; + + if (card != controller) { + host->flags &= ~HOST_F_ACTIVE; + if (card) host->flags |= HOST_F_ACTIVE; + mmc_detect_change(host->mmc, 0); + } + + if (host->mrq != NULL) { + u32 status = au_readl(HOST_STATUS(host)); + DBG("PENDING - %8.8x\n", host->id, status); + } + + mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT); +} + +static dbdev_tab_t au1xmmc_mem_dbdev = +{ + DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 8, 0x00000000, 0, 0 +}; + +static void au1xmmc_init_dma(struct au1xmmc_host *host) +{ + + u32 rxchan, txchan; + + int txid = au1xmmc_card_table[host->id].tx_devid; + int rxid = au1xmmc_card_table[host->id].rx_devid; + + /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride + of 8 bits. And since devices are shared, we need to create + our own to avoid freaking out other devices + */ + + int memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev); + + txchan = au1xxx_dbdma_chan_alloc(memid, txid, + au1xmmc_dma_callback, (void *) host); + + rxchan = au1xxx_dbdma_chan_alloc(rxid, memid, + au1xmmc_dma_callback, (void *) host); + + au1xxx_dbdma_set_devwidth(txchan, 8); + au1xxx_dbdma_set_devwidth(rxchan, 8); + + au1xxx_dbdma_ring_alloc(txchan, AU1XMMC_DESCRIPTOR_COUNT); + au1xxx_dbdma_ring_alloc(rxchan, AU1XMMC_DESCRIPTOR_COUNT); + + host->tx_chan = txchan; + host->rx_chan = rxchan; +} + +static const struct mmc_host_ops au1xmmc_ops = { + .request = au1xmmc_request, + .set_ios = au1xmmc_set_ios, + .get_ro = au1xmmc_card_readonly, +}; + +static int __devinit au1xmmc_probe(struct platform_device *pdev) +{ + + int i, ret = 0; + + /* THe interrupt is shared among all controllers */ + ret = request_irq(AU1100_SD_IRQ, au1xmmc_irq, IRQF_DISABLED, "MMC", 0); + + if (ret) { + printk(DRIVER_NAME "ERROR: Couldn't get int %d: %d\n", + AU1100_SD_IRQ, ret); + return -ENXIO; + } + + disable_irq(AU1100_SD_IRQ); + + for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) { + struct mmc_host *mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev); + struct au1xmmc_host *host = 0; + + if (!mmc) { + printk(DRIVER_NAME "ERROR: no mem for host %d\n", i); + au1xmmc_hosts[i] = 0; + continue; + } + + mmc->ops = &au1xmmc_ops; + + mmc->f_min = 450000; + mmc->f_max = 24000000; + + mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE; + mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT; + + mmc->max_blk_size = 2048; + mmc->max_blk_count = 512; + + mmc->ocr_avail = AU1XMMC_OCR; + + host = mmc_priv(mmc); + host->mmc = mmc; + + host->id = i; + host->iobase = au1xmmc_card_table[host->id].iobase; + host->clock = 0; + host->power_mode = MMC_POWER_OFF; + + host->flags = au1xmmc_card_inserted(host) ? HOST_F_ACTIVE : 0; + host->status = HOST_S_IDLE; + + init_timer(&host->timer); + + host->timer.function = au1xmmc_poll_event; + host->timer.data = (unsigned long) host; + host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT; + + tasklet_init(&host->data_task, au1xmmc_tasklet_data, + (unsigned long) host); + + tasklet_init(&host->finish_task, au1xmmc_tasklet_finish, + (unsigned long) host); + + spin_lock_init(&host->lock); + + if (dma != 0) + au1xmmc_init_dma(host); + + au1xmmc_reset_controller(host); + + mmc_add_host(mmc); + au1xmmc_hosts[i] = host; + + add_timer(&host->timer); + + printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X (mode=%s)\n", + host->id, host->iobase, dma ? "dma" : "pio"); + } + + enable_irq(AU1100_SD_IRQ); + + return 0; +} + +static int __devexit au1xmmc_remove(struct platform_device *pdev) +{ + + int i; + + disable_irq(AU1100_SD_IRQ); + + for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) { + struct au1xmmc_host *host = au1xmmc_hosts[i]; + if (!host) continue; + + tasklet_kill(&host->data_task); + tasklet_kill(&host->finish_task); + + del_timer_sync(&host->timer); + au1xmmc_set_power(host, 0); + + mmc_remove_host(host->mmc); + + au1xxx_dbdma_chan_free(host->tx_chan); + au1xxx_dbdma_chan_free(host->rx_chan); + + au_writel(0x0, HOST_ENABLE(host)); + au_sync(); + } + + free_irq(AU1100_SD_IRQ, 0); + return 0; +} + +static struct platform_driver au1xmmc_driver = { + .probe = au1xmmc_probe, + .remove = au1xmmc_remove, + .suspend = NULL, + .resume = NULL, + .driver = { + .name = DRIVER_NAME, + }, +}; + +static int __init au1xmmc_init(void) +{ + return platform_driver_register(&au1xmmc_driver); +} + +static void __exit au1xmmc_exit(void) +{ + platform_driver_unregister(&au1xmmc_driver); +} + +module_init(au1xmmc_init); +module_exit(au1xmmc_exit); + +#ifdef MODULE +MODULE_AUTHOR("Advanced Micro Devices, Inc"); +MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX"); +MODULE_LICENSE("GPL"); +#endif + |
