summaryrefslogtreecommitdiffstats
path: root/drivers/media/tuners/mt2060_priv.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/media/tuners/mt2060_priv.h')
-rw-r--r--drivers/media/tuners/mt2060_priv.h104
1 files changed, 104 insertions, 0 deletions
diff --git a/drivers/media/tuners/mt2060_priv.h b/drivers/media/tuners/mt2060_priv.h
new file mode 100644
index 0000000..2b60de6
--- /dev/null
+++ b/drivers/media/tuners/mt2060_priv.h
@@ -0,0 +1,104 @@
+/*
+ * Driver for Microtune MT2060 "Single chip dual conversion broadband tuner"
+ *
+ * Copyright (c) 2006 Olivier DANET <odanet@caramail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ *
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.=
+ */
+
+#ifndef MT2060_PRIV_H
+#define MT2060_PRIV_H
+
+// Uncomment the #define below to enable spurs checking. The results where quite unconvincing.
+// #define MT2060_SPURCHECK
+
+/* This driver is based on the information available in the datasheet of the
+ "Comtech SDVBT-3K6M" tuner ( K1000737843.pdf ) which features the MT2060 register map :
+
+ I2C Address : 0x60
+
+ Reg.No | B7 | B6 | B5 | B4 | B3 | B2 | B1 | B0 | ( defaults )
+ --------------------------------------------------------------------------------
+ 00 | [ PART ] | [ REV ] | R = 0x63
+ 01 | [ LNABAND ] | [ NUM1(5:2) ] | RW = 0x3F
+ 02 | [ DIV1 ] | RW = 0x74
+ 03 | FM1CA | FM1SS | [ NUM1(1:0) ] | [ NUM2(3:0) ] | RW = 0x00
+ 04 | NUM2(11:4) ] | RW = 0x08
+ 05 | [ DIV2 ] |NUM2(12)| RW = 0x93
+ 06 | L1LK | [ TAD1 ] | L2LK | [ TAD2 ] | R
+ 07 | [ FMF ] | R
+ 08 | ? | FMCAL | ? | ? | ? | ? | ? | TEMP | R
+ 09 | 0 | 0 | [ FMGC ] | 0 | GP02 | GP01 | 0 | RW = 0x20
+ 0A | ??
+ 0B | 0 | 0 | 1 | 1 | 0 | 0 | [ VGAG ] | RW = 0x30
+ 0C | V1CSE | 1 | 1 | 1 | 1 | 1 | 1 | 1 | RW = 0xFF
+ 0D | 1 | 0 | [ V1CS ] | RW = 0xB0
+ 0E | ??
+ 0F | ??
+ 10 | ??
+ 11 | [ LOTO ] | 0 | 0 | 1 | 0 | RW = 0x42
+
+ PART : Part code : 6 for MT2060
+ REV : Revision code : 3 for current revision
+ LNABAND : Input frequency range : ( See code for details )
+ NUM1 / DIV1 / NUM2 / DIV2 : Frequencies programming ( See code for details )
+ FM1CA : Calibration Start Bit
+ FM1SS : Calibration Single Step bit
+ L1LK : LO1 Lock Detect
+ TAD1 : Tune Line ADC ( ? )
+ L2LK : LO2 Lock Detect
+ TAD2 : Tune Line ADC ( ? )
+ FMF : Estimated first IF Center frequency Offset ( ? )
+ FM1CAL : Calibration done bit
+ TEMP : On chip temperature sensor
+ FMCG : Mixer 1 Cap Gain ( ? )
+ GP01 / GP02 : Programmable digital outputs. Unconnected pins ?
+ V1CSE : LO1 VCO Automatic Capacitor Select Enable ( ? )
+ V1CS : LO1 Capacitor Selection Value ( ? )
+ LOTO : LO Timeout ( ? )
+ VGAG : Tuner Output gain
+*/
+
+#define I2C_ADDRESS 0x60
+
+#define REG_PART_REV 0
+#define REG_LO1C1 1
+#define REG_LO1C2 2
+#define REG_LO2C1 3
+#define REG_LO2C2 4
+#define REG_LO2C3 5
+#define REG_LO_STATUS 6
+#define REG_FM_FREQ 7
+#define REG_MISC_STAT 8
+#define REG_MISC_CTRL 9
+#define REG_RESERVED_A 0x0A
+#define REG_VGAG 0x0B
+#define REG_LO1B1 0x0C
+#define REG_LO1B2 0x0D
+#define REG_LOTO 0x11
+
+#define PART_REV 0x63 // The current driver works only with PART=6 and REV=3 chips
+
+struct mt2060_priv {
+ struct mt2060_config *cfg;
+ struct i2c_adapter *i2c;
+
+ u32 frequency;
+ u16 if1_freq;
+ u8 fmfreq;
+};
+
+#endif
OpenPOWER on IntegriCloud