diff options
Diffstat (limited to 'drivers/media/dvb/frontends/cx24110.c')
| -rw-r--r-- | drivers/media/dvb/frontends/cx24110.c | 657 |
1 files changed, 657 insertions, 0 deletions
diff --git a/drivers/media/dvb/frontends/cx24110.c b/drivers/media/dvb/frontends/cx24110.c new file mode 100644 index 0000000..ae16112 --- /dev/null +++ b/drivers/media/dvb/frontends/cx24110.c @@ -0,0 +1,657 @@ +/* + cx24110 - Single Chip Satellite Channel Receiver driver module + + Copyright (C) 2002 Peter Hettkamp <peter.hettkamp@t-online.de> based on + work + Copyright (C) 1999 Convergence Integrated Media GmbH <ralph@convergence.de> + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + +*/ + +#include <linux/slab.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/init.h> + +#include "dvb_frontend.h" +#include "cx24110.h" + + +struct cx24110_state { + + struct i2c_adapter* i2c; + + struct dvb_frontend_ops ops; + + const struct cx24110_config* config; + + struct dvb_frontend frontend; + + u32 lastber; + u32 lastbler; + u32 lastesn0; +}; + +static int debug; +#define dprintk(args...) \ + do { \ + if (debug) printk(KERN_DEBUG "cx24110: " args); \ + } while (0) + +static struct {u8 reg; u8 data;} cx24110_regdata[]= + /* Comments beginning with @ denote this value should + be the default */ + {{0x09,0x01}, /* SoftResetAll */ + {0x09,0x00}, /* release reset */ + {0x01,0xe8}, /* MSB of code rate 27.5MS/s */ + {0x02,0x17}, /* middle byte " */ + {0x03,0x29}, /* LSB " */ + {0x05,0x03}, /* @ DVB mode, standard code rate 3/4 */ + {0x06,0xa5}, /* @ PLL 60MHz */ + {0x07,0x01}, /* @ Fclk, i.e. sampling clock, 60MHz */ + {0x0a,0x00}, /* @ partial chip disables, do not set */ + {0x0b,0x01}, /* set output clock in gapped mode, start signal low + active for first byte */ + {0x0c,0x11}, /* no parity bytes, large hold time, serial data out */ + {0x0d,0x6f}, /* @ RS Sync/Unsync thresholds */ + {0x10,0x40}, /* chip doc is misleading here: write bit 6 as 1 + to avoid starting the BER counter. Reset the + CRC test bit. Finite counting selected */ + {0x15,0xff}, /* @ size of the limited time window for RS BER + estimation. It is <value>*256 RS blocks, this + gives approx. 2.6 sec at 27.5MS/s, rate 3/4 */ + {0x16,0x00}, /* @ enable all RS output ports */ + {0x17,0x04}, /* @ time window allowed for the RS to sync */ + {0x18,0xae}, /* @ allow all standard DVB code rates to be scanned + for automatically */ + /* leave the current code rate and normalization + registers as they are after reset... */ + {0x21,0x10}, /* @ during AutoAcq, search each viterbi setting + only once */ + {0x23,0x18}, /* @ size of the limited time window for Viterbi BER + estimation. It is <value>*65536 channel bits, i.e. + approx. 38ms at 27.5MS/s, rate 3/4 */ + {0x24,0x24}, /* do not trigger Viterbi CRC test. Finite count window */ + /* leave front-end AGC parameters at default values */ + /* leave decimation AGC parameters at default values */ + {0x35,0x40}, /* disable all interrupts. They are not connected anyway */ + {0x36,0xff}, /* clear all interrupt pending flags */ + {0x37,0x00}, /* @ fully enable AutoAcqq state machine */ + {0x38,0x07}, /* @ enable fade recovery, but not autostart AutoAcq */ + /* leave the equalizer parameters on their default values */ + /* leave the final AGC parameters on their default values */ + {0x41,0x00}, /* @ MSB of front-end derotator frequency */ + {0x42,0x00}, /* @ middle bytes " */ + {0x43,0x00}, /* @ LSB " */ + /* leave the carrier tracking loop parameters on default */ + /* leave the bit timing loop parameters at gefault */ + {0x56,0x4d}, /* set the filtune voltage to 2.7V, as recommended by */ + /* the cx24108 data sheet for symbol rates above 15MS/s */ + {0x57,0x00}, /* @ Filter sigma delta enabled, positive */ + {0x61,0x95}, /* GPIO pins 1-4 have special function */ + {0x62,0x05}, /* GPIO pin 5 has special function, pin 6 is GPIO */ + {0x63,0x00}, /* All GPIO pins use CMOS output characteristics */ + {0x64,0x20}, /* GPIO 6 is input, all others are outputs */ + {0x6d,0x30}, /* tuner auto mode clock freq 62kHz */ + {0x70,0x15}, /* use auto mode, tuner word is 21 bits long */ + {0x73,0x00}, /* @ disable several demod bypasses */ + {0x74,0x00}, /* @ " */ + {0x75,0x00} /* @ " */ + /* the remaining registers are for SEC */ + }; + + +static int cx24110_writereg (struct cx24110_state* state, int reg, int data) +{ + u8 buf [] = { reg, data }; + struct i2c_msg msg = { .addr = state->config->demod_address, .flags = 0, .buf = buf, .len = 2 }; + int err; + + if ((err = i2c_transfer(state->i2c, &msg, 1)) != 1) { + dprintk ("%s: writereg error (err == %i, reg == 0x%02x," + " data == 0x%02x)\n", __FUNCTION__, err, reg, data); + return -EREMOTEIO; + } + + return 0; +} + +static int cx24110_readreg (struct cx24110_state* state, u8 reg) +{ + int ret; + u8 b0 [] = { reg }; + u8 b1 [] = { 0 }; + struct i2c_msg msg [] = { { .addr = state->config->demod_address, .flags = 0, .buf = b0, .len = 1 }, + { .addr = state->config->demod_address, .flags = I2C_M_RD, .buf = b1, .len = 1 } }; + + ret = i2c_transfer(state->i2c, msg, 2); + + if (ret != 2) return ret; + + return b1[0]; +} + +static int cx24110_set_inversion (struct cx24110_state* state, fe_spectral_inversion_t inversion) +{ +/* fixme (low): error handling */ + + switch (inversion) { + case INVERSION_OFF: + cx24110_writereg(state,0x37,cx24110_readreg(state,0x37)|0x1); + /* AcqSpectrInvDis on. No idea why someone should want this */ + cx24110_writereg(state,0x5,cx24110_readreg(state,0x5)&0xf7); + /* Initial value 0 at start of acq */ + cx24110_writereg(state,0x22,cx24110_readreg(state,0x22)&0xef); + /* current value 0 */ + /* The cx24110 manual tells us this reg is read-only. + But what the heck... set it ayways */ + break; + case INVERSION_ON: + cx24110_writereg(state,0x37,cx24110_readreg(state,0x37)|0x1); + /* AcqSpectrInvDis on. No idea why someone should want this */ + cx24110_writereg(state,0x5,cx24110_readreg(state,0x5)|0x08); + /* Initial value 1 at start of acq */ + cx24110_writereg(state,0x22,cx24110_readreg(state,0x22)|0x10); + /* current value 1 */ + break; + case INVERSION_AUTO: + cx24110_writereg(state,0x37,cx24110_readreg(state,0x37)&0xfe); + /* AcqSpectrInvDis off. Leave initial & current states as is */ + break; + default: + return -EINVAL; + } + + return 0; +} + +static int cx24110_set_fec (struct cx24110_state* state, fe_code_rate_t fec) +{ +/* fixme (low): error handling */ + + static const int rate[]={-1,1,2,3,5,7,-1}; + static const int g1[]={-1,0x01,0x02,0x05,0x15,0x45,-1}; + static const int g2[]={-1,0x01,0x03,0x06,0x1a,0x7a,-1}; + + /* Well, the AutoAcq engine of the cx24106 and 24110 automatically + searches all enabled viterbi rates, and can handle non-standard + rates as well. */ + + if (fec>FEC_AUTO) + fec=FEC_AUTO; + + if (fec==FEC_AUTO) { /* (re-)establish AutoAcq behaviour */ + cx24110_writereg(state,0x37,cx24110_readreg(state,0x37)&0xdf); + /* clear AcqVitDis bit */ + cx24110_writereg(state,0x18,0xae); + /* allow all DVB standard code rates */ + cx24110_writereg(state,0x05,(cx24110_readreg(state,0x05)&0xf0)|0x3); + /* set nominal Viterbi rate 3/4 */ + cx24110_writereg(state,0x22,(cx24110_readreg(state,0x22)&0xf0)|0x3); + /* set current Viterbi rate 3/4 */ + cx24110_writereg(state,0x1a,0x05); cx24110_writereg(state,0x1b,0x06); + /* set the puncture registers for code rate 3/4 */ + return 0; + } else { + cx24110_writereg(state,0x37,cx24110_readreg(state,0x37)|0x20); + /* set AcqVitDis bit */ + if(rate[fec]>0) { + cx24110_writereg(state,0x05,(cx24110_readreg(state,0x05)&0xf0)|rate[fec]); + /* set nominal Viterbi rate */ + cx24110_writereg(state,0x22,(cx24110_readreg(state,0x22)&0xf0)|rate[fec]); + /* set current Viterbi rate */ + cx24110_writereg(state,0x1a,g1[fec]); + cx24110_writereg(state,0x1b,g2[fec]); + /* not sure if this is the right way: I always used AutoAcq mode */ + } else + return -EOPNOTSUPP; +/* fixme (low): which is the correct return code? */ + }; + return 0; +} + +static fe_code_rate_t cx24110_get_fec (struct cx24110_state* state) +{ + int i; + + i=cx24110_readreg(state,0x22)&0x0f; + if(!(i&0x08)) { + return FEC_1_2 + i - 1; + } else { +/* fixme (low): a special code rate has been selected. In theory, we need to + return a denominator value, a numerator value, and a pair of puncture + maps to correctly describe this mode. But this should never happen in + practice, because it cannot be set by cx24110_get_fec. */ + return FEC_NONE; + } +} + +static int cx24110_set_symbolrate (struct cx24110_state* state, u32 srate) +{ +/* fixme (low): add error handling */ + u32 ratio; + u32 tmp, fclk, BDRI; + + static const u32 bands[]={5000000UL,15000000UL,90999000UL/2}; + int i; + +dprintk("cx24110 debug: entering %s(%d)\n",__FUNCTION__,srate); + if (srate>90999000UL/2) + srate=90999000UL/2; + if (srate<500000) + srate=500000; + + for(i=0;(i<sizeof(bands)/sizeof(bands[0]))&&(srate>bands[i]);i++) + ; + /* first, check which sample rate is appropriate: 45, 60 80 or 90 MHz, + and set the PLL accordingly (R07[1:0] Fclk, R06[7:4] PLLmult, + R06[3:0] PLLphaseDetGain */ + tmp=cx24110_readreg(state,0x07)&0xfc; + if(srate<90999000UL/4) { /* sample rate 45MHz*/ + cx24110_writereg(state,0x07,tmp); + cx24110_writereg(state,0x06,0x78); + fclk=90999000UL/2; + } else if(srate<60666000UL/2) { /* sample rate 60MHz */ + cx24110_writereg(state,0x07,tmp|0x1); + cx24110_writereg(state,0x06,0xa5); + fclk=60666000UL; + } else if(srate<80888000UL/2) { /* sample rate 80MHz */ + cx24110_writereg(state,0x07,tmp|0x2); + cx24110_writereg(state,0x06,0x87); + fclk=80888000UL; + } else { /* sample rate 90MHz */ + cx24110_writereg(state,0x07,tmp|0x3); + cx24110_writereg(state,0x06,0x78); + fclk=90999000UL; + }; + dprintk("cx24110 debug: fclk %d Hz\n",fclk); + /* we need to divide two integers with approx. 27 bits in 32 bit + arithmetic giving a 25 bit result */ + /* the maximum dividend is 90999000/2, 0x02b6446c, this number is + also the most complex divisor. Hence, the dividend has, + assuming 32bit unsigned arithmetic, 6 clear bits on top, the + divisor 2 unused bits at the bottom. Also, the quotient is + always less than 1/2. Borrowed from VES1893.c, of course */ + + tmp=srate<<6; + BDRI=fclk>>2; + ratio=(tmp/BDRI); + + tmp=(tmp%BDRI)<<8; + ratio=(ratio<<8)+(tmp/BDRI); + + tmp=(tmp%BDRI)<<8; + ratio=(ratio<<8)+(tmp/BDRI); + + tmp=(tmp%BDRI)<<1; + ratio=(ratio<<1)+(tmp/BDRI); + + dprintk("srate= %d (range %d, up to %d)\n", srate,i,bands[i]); + dprintk("fclk = %d\n", fclk); + dprintk("ratio= %08x\n", ratio); + + cx24110_writereg(state, 0x1, (ratio>>16)&0xff); + cx24110_writereg(state, 0x2, (ratio>>8)&0xff); + cx24110_writereg(state, 0x3, (ratio)&0xff); + + return 0; + +} + +int cx24110_pll_write (struct dvb_frontend* fe, u32 data) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + +/* tuner data is 21 bits long, must be left-aligned in data */ +/* tuner cx24108 is written through a dedicated 3wire interface on the demod chip */ +/* FIXME (low): add error handling, avoid infinite loops if HW fails... */ + + dprintk("cx24110 debug: cx24108_write(%8.8x)\n",data); + + cx24110_writereg(state,0x6d,0x30); /* auto mode at 62kHz */ + cx24110_writereg(state,0x70,0x15); /* auto mode 21 bits */ + + /* if the auto tuner writer is still busy, clear it out */ + while (cx24110_readreg(state,0x6d)&0x80) + cx24110_writereg(state,0x72,0); + + /* write the topmost 8 bits */ + cx24110_writereg(state,0x72,(data>>24)&0xff); + + /* wait for the send to be completed */ + while ((cx24110_readreg(state,0x6d)&0xc0)==0x80) + ; + + /* send another 8 bytes */ + cx24110_writereg(state,0x72,(data>>16)&0xff); + while ((cx24110_readreg(state,0x6d)&0xc0)==0x80) + ; + + /* and the topmost 5 bits of this byte */ + cx24110_writereg(state,0x72,(data>>8)&0xff); + while ((cx24110_readreg(state,0x6d)&0xc0)==0x80) + ; + + /* now strobe the enable line once */ + cx24110_writereg(state,0x6d,0x32); + cx24110_writereg(state,0x6d,0x30); + + return 0; +} + +static int cx24110_initfe(struct dvb_frontend* fe) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; +/* fixme (low): error handling */ + int i; + + dprintk("%s: init chip\n", __FUNCTION__); + + for(i=0;i<sizeof(cx24110_regdata)/sizeof(cx24110_regdata[0]);i++) { + cx24110_writereg(state, cx24110_regdata[i].reg, cx24110_regdata[i].data); + }; + + if (state->config->pll_init) state->config->pll_init(fe); + + return 0; +} + +static int cx24110_set_voltage (struct dvb_frontend* fe, fe_sec_voltage_t voltage) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + + switch (voltage) { + case SEC_VOLTAGE_13: + return cx24110_writereg(state,0x76,(cx24110_readreg(state,0x76)&0x3b)|0xc0); + case SEC_VOLTAGE_18: + return cx24110_writereg(state,0x76,(cx24110_readreg(state,0x76)&0x3b)|0x40); + default: + return -EINVAL; + }; +} + +static int cx24110_diseqc_send_burst(struct dvb_frontend* fe, + fe_sec_mini_cmd_t burst) +{ + int rv, bit, i; + struct cx24110_state *state = fe->demodulator_priv; + + if (burst == SEC_MINI_A) + bit = 0x00; + else if (burst == SEC_MINI_B) + bit = 0x08; + else + return -EINVAL; + + rv = cx24110_readreg(state, 0x77); + cx24110_writereg(state, 0x77, rv|0x04); + + rv = cx24110_readreg(state, 0x76); + cx24110_writereg(state, 0x76, ((rv & 0x90) | 0x40 | bit)); + for (i = 500; i-- > 0 && !(cx24110_readreg(state,0x76)&0x40) ; ) + ; /* wait for LNB ready */ + + return 0; +} + +static int cx24110_send_diseqc_msg(struct dvb_frontend* fe, + struct dvb_diseqc_master_cmd *cmd) +{ + int i, rv; + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + + for (i = 0; i < cmd->msg_len; i++) + cx24110_writereg(state, 0x79 + i, cmd->msg[i]); + + rv = cx24110_readreg(state, 0x77); + cx24110_writereg(state, 0x77, rv|0x04); + + rv = cx24110_readreg(state, 0x76); + + cx24110_writereg(state, 0x76, ((rv & 0x90) | 0x40) | ((cmd->msg_len-3) & 3)); + for (i=500; i-- > 0 && !(cx24110_readreg(state,0x76)&0x40);) + ; /* wait for LNB ready */ + + return 0; +} + +static int cx24110_read_status(struct dvb_frontend* fe, fe_status_t* status) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + + int sync = cx24110_readreg (state, 0x55); + + *status = 0; + + if (sync & 0x10) + *status |= FE_HAS_SIGNAL; + + if (sync & 0x08) + *status |= FE_HAS_CARRIER; + + sync = cx24110_readreg (state, 0x08); + + if (sync & 0x40) + *status |= FE_HAS_VITERBI; + + if (sync & 0x20) + *status |= FE_HAS_SYNC; + + if ((sync & 0x60) == 0x60) + *status |= FE_HAS_LOCK; + + return 0; +} + +static int cx24110_read_ber(struct dvb_frontend* fe, u32* ber) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + + /* fixme (maybe): value range is 16 bit. Scale? */ + if(cx24110_readreg(state,0x24)&0x10) { + /* the Viterbi error counter has finished one counting window */ + cx24110_writereg(state,0x24,0x04); /* select the ber reg */ + state->lastber=cx24110_readreg(state,0x25)| + (cx24110_readreg(state,0x26)<<8); + cx24110_writereg(state,0x24,0x04); /* start new count window */ + cx24110_writereg(state,0x24,0x14); + } + *ber = state->lastber; + + return 0; +} + +static int cx24110_read_signal_strength(struct dvb_frontend* fe, u16* signal_strength) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + +/* no provision in hardware. Read the frontend AGC accumulator. No idea how to scale this, but I know it is 2s complement */ + u8 signal = cx24110_readreg (state, 0x27)+128; + *signal_strength = (signal << 8) | signal; + + return 0; +} + +static int cx24110_read_snr(struct dvb_frontend* fe, u16* snr) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + + /* no provision in hardware. Can be computed from the Es/N0 estimator, but I don't know how. */ + if(cx24110_readreg(state,0x6a)&0x80) { + /* the Es/N0 error counter has finished one counting window */ + state->lastesn0=cx24110_readreg(state,0x69)| + (cx24110_readreg(state,0x68)<<8); + cx24110_writereg(state,0x6a,0x84); /* start new count window */ + } + *snr = state->lastesn0; + + return 0; +} + +static int cx24110_read_ucblocks(struct dvb_frontend* fe, u32* ucblocks) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + u32 lastbyer; + + if(cx24110_readreg(state,0x10)&0x40) { + /* the RS error counter has finished one counting window */ + cx24110_writereg(state,0x10,0x60); /* select the byer reg */ + lastbyer=cx24110_readreg(state,0x12)| + (cx24110_readreg(state,0x13)<<8)| + (cx24110_readreg(state,0x14)<<16); + cx24110_writereg(state,0x10,0x70); /* select the bler reg */ + state->lastbler=cx24110_readreg(state,0x12)| + (cx24110_readreg(state,0x13)<<8)| + (cx24110_readreg(state,0x14)<<16); + cx24110_writereg(state,0x10,0x20); /* start new count window */ + } + *ucblocks = state->lastbler; + + return 0; +} + +static int cx24110_set_frontend(struct dvb_frontend* fe, struct dvb_frontend_parameters *p) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + + state->config->pll_set(fe, p); + cx24110_set_inversion (state, p->inversion); + cx24110_set_fec (state, p->u.qpsk.fec_inner); + cx24110_set_symbolrate (state, p->u.qpsk.symbol_rate); + cx24110_writereg(state,0x04,0x05); /* start aquisition */ + + return 0; +} + +static int cx24110_get_frontend(struct dvb_frontend* fe, struct dvb_frontend_parameters *p) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + s32 afc; unsigned sclk; + +/* cannot read back tuner settings (freq). Need to have some private storage */ + + sclk = cx24110_readreg (state, 0x07) & 0x03; +/* ok, real AFC (FEDR) freq. is afc/2^24*fsamp, fsamp=45/60/80/90MHz. + * Need 64 bit arithmetic. Is thiss possible in the kernel? */ + if (sclk==0) sclk=90999000L/2L; + else if (sclk==1) sclk=60666000L; + else if (sclk==2) sclk=80888000L; + else sclk=90999000L; + sclk>>=8; + afc = sclk*(cx24110_readreg (state, 0x44)&0x1f)+ + ((sclk*cx24110_readreg (state, 0x45))>>8)+ + ((sclk*cx24110_readreg (state, 0x46))>>16); + + p->frequency += afc; + p->inversion = (cx24110_readreg (state, 0x22) & 0x10) ? + INVERSION_ON : INVERSION_OFF; + p->u.qpsk.fec_inner = cx24110_get_fec (state); + + return 0; +} + +static int cx24110_set_tone(struct dvb_frontend* fe, fe_sec_tone_mode_t tone) +{ + struct cx24110_state *state = (struct cx24110_state*) fe->demodulator_priv; + + return cx24110_writereg(state,0x76,(cx24110_readreg(state,0x76)&~0x10)|(((tone==SEC_TONE_ON))?0x10:0)); +} + +static void cx24110_release(struct dvb_frontend* fe) +{ + struct cx24110_state* state = (struct cx24110_state*) fe->demodulator_priv; + kfree(state); +} + +static struct dvb_frontend_ops cx24110_ops; + +struct dvb_frontend* cx24110_attach(const struct cx24110_config* config, + struct i2c_adapter* i2c) +{ + struct cx24110_state* state = NULL; + int ret; + + /* allocate memory for the internal state */ + state = (struct cx24110_state*) kmalloc(sizeof(struct cx24110_state), GFP_KERNEL); + if (state == NULL) goto error; + + /* setup the state */ + state->config = config; + state->i2c = i2c; + memcpy(&state->ops, &cx24110_ops, sizeof(struct dvb_frontend_ops)); + state->lastber = 0; + state->lastbler = 0; + state->lastesn0 = 0; + + /* check if the demod is there */ + ret = cx24110_readreg(state, 0x00); + if ((ret != 0x5a) && (ret != 0x69)) goto error; + + /* create dvb_frontend */ + state->frontend.ops = &state->ops; + state->frontend.demodulator_priv = state; + return &state->frontend; + +error: + kfree(state); + return NULL; +} + +static struct dvb_frontend_ops cx24110_ops = { + + .info = { + .name = "Conexant CX24110 DVB-S", + .type = FE_QPSK, + .frequency_min = 950000, + .frequency_max = 2150000, + .frequency_stepsize = 1011, /* kHz for QPSK frontends */ + .frequency_tolerance = 29500, + .symbol_rate_min = 1000000, + .symbol_rate_max = 45000000, + .caps = FE_CAN_INVERSION_AUTO | + FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 | + FE_CAN_FEC_5_6 | FE_CAN_FEC_7_8 | FE_CAN_FEC_AUTO | + FE_CAN_QPSK | FE_CAN_RECOVER + }, + + .release = cx24110_release, + + .init = cx24110_initfe, + .set_frontend = cx24110_set_frontend, + .get_frontend = cx24110_get_frontend, + .read_status = cx24110_read_status, + .read_ber = cx24110_read_ber, + .read_signal_strength = cx24110_read_signal_strength, + .read_snr = cx24110_read_snr, + .read_ucblocks = cx24110_read_ucblocks, + + .diseqc_send_master_cmd = cx24110_send_diseqc_msg, + .set_tone = cx24110_set_tone, + .set_voltage = cx24110_set_voltage, + .diseqc_send_burst = cx24110_diseqc_send_burst, +}; + +module_param(debug, int, 0644); +MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off)."); + +MODULE_DESCRIPTION("Conexant CX24110 DVB-S Demodulator driver"); +MODULE_AUTHOR("Peter Hettkamp"); +MODULE_LICENSE("GPL"); + +EXPORT_SYMBOL(cx24110_attach); +EXPORT_SYMBOL(cx24110_pll_write); |
