diff options
Diffstat (limited to 'drivers/leds/Kconfig')
-rw-r--r-- | drivers/leds/Kconfig | 55 |
1 files changed, 45 insertions, 10 deletions
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig index ec568fa..859814f 100644 --- a/drivers/leds/Kconfig +++ b/drivers/leds/Kconfig @@ -18,6 +18,13 @@ config LEDS_CLASS comment "LED drivers" +config LEDS_ATMEL_PWM + tristate "LED Support using Atmel PWM outputs" + depends on LEDS_CLASS && ATMEL_PWM + help + This option enables support for LEDs driven using outputs + of the dedicated PWM controller found on newer Atmel SOCs. + config LEDS_CORGI tristate "LED Support for the Sharp SL-C7x0 series" depends on LEDS_CLASS && PXA_SHARP_C7xx @@ -39,15 +46,6 @@ config LEDS_SPITZ This option enables support for the LEDs on Sharp Zaurus SL-Cxx00 series (C1000, C3000, C3100). -config LEDS_IXP4XX - tristate "LED Support for GPIO connected LEDs on IXP4XX processors" - depends on LEDS_CLASS && ARCH_IXP4XX - help - This option enables support for the LEDs connected to GPIO - outputs of the Intel IXP4XX processors. To be useful the - particular board must have LEDs and they must be connected - to the GPIO lines. If unsure, say Y. - config LEDS_TOSA tristate "LED Support for the Sharp SL-6000 series" depends on LEDS_CLASS && PXA_SHARPSL @@ -100,6 +98,13 @@ config LEDS_COBALT_RAQ help This option enables support for the Cobalt Raq series LEDs. +config LEDS_HP6XX + tristate "LED Support for the HP Jornada 6xx" + depends on LEDS_CLASS && SH_HP6XX + help + This option enables led support for the handheld + HP Jornada 620/660/680/690. + config LEDS_GPIO tristate "LED Support for GPIO connected LEDs" depends on LEDS_CLASS && GENERIC_GPIO @@ -114,6 +119,32 @@ config LEDS_CM_X270 help This option enables support for the CM-X270 LEDs. +config LEDS_CLEVO_MAIL + tristate "Mail LED on Clevo notebook (EXPERIMENTAL)" + depends on LEDS_CLASS && X86 && SERIO_I8042 && DMI && EXPERIMENTAL + help + This driver makes the mail LED accessible from userspace + programs through the leds subsystem. This LED have three + known mode: off, blink at 0.5Hz and blink at 1Hz. + + The driver supports two kinds of interface: using ledtrig-timer + or through /sys/class/leds/clevo::mail/brightness. As this LED + cannot change it's brightness it blinks instead. The brightness + value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means + blink at 1Hz. + + This module can drive the mail LED for the following notebooks: + + Clevo D410J + Clevo D410V + Clevo D400V/D470V (not tested, but might work) + Clevo M540N + Clevo M5x0N (not tested, but might work) + Positivo Mobile (Clevo M5x0V) + + To compile this driver as a module, choose M here: the + module will be called leds-clevo-mail. + comment "LED Triggers" config LEDS_TRIGGERS @@ -128,7 +159,11 @@ config LEDS_TRIGGER_TIMER depends on LEDS_TRIGGERS help This allows LEDs to be controlled by a programmable timer - via sysfs. If unsure, say Y. + via sysfs. Some LED hardware can be programmed to start + blinking the LED without any further software interaction. + For more details read Documentation/leds-class.txt. + + If unsure, say Y. config LEDS_TRIGGER_IDE_DISK bool "LED IDE Disk Trigger" |