diff options
Diffstat (limited to 'drivers/input/touchscreen/tsc2005.c')
-rw-r--r-- | drivers/input/touchscreen/tsc2005.c | 264 |
1 files changed, 102 insertions, 162 deletions
diff --git a/drivers/input/touchscreen/tsc2005.c b/drivers/input/touchscreen/tsc2005.c index d8c025b..0f65d02 100644 --- a/drivers/input/touchscreen/tsc2005.c +++ b/drivers/input/touchscreen/tsc2005.c @@ -30,10 +30,11 @@ #include <linux/delay.h> #include <linux/pm.h> #include <linux/of.h> -#include <linux/of_gpio.h> #include <linux/spi/spi.h> #include <linux/spi/tsc2005.h> #include <linux/regulator/consumer.h> +#include <linux/regmap.h> +#include <linux/gpio/consumer.h> /* * The touchscreen interface operates as follows: @@ -61,16 +62,24 @@ #define TSC2005_CMD_12BIT 0x04 /* control byte 0 */ -#define TSC2005_REG_READ 0x0001 -#define TSC2005_REG_PND0 0x0002 -#define TSC2005_REG_X 0x0000 -#define TSC2005_REG_Y 0x0008 -#define TSC2005_REG_Z1 0x0010 -#define TSC2005_REG_Z2 0x0018 -#define TSC2005_REG_TEMP_HIGH 0x0050 -#define TSC2005_REG_CFR0 0x0060 -#define TSC2005_REG_CFR1 0x0068 -#define TSC2005_REG_CFR2 0x0070 +#define TSC2005_REG_READ 0x01 /* R/W access */ +#define TSC2005_REG_PND0 0x02 /* Power Not Down Control */ +#define TSC2005_REG_X (0x0 << 3) +#define TSC2005_REG_Y (0x1 << 3) +#define TSC2005_REG_Z1 (0x2 << 3) +#define TSC2005_REG_Z2 (0x3 << 3) +#define TSC2005_REG_AUX (0x4 << 3) +#define TSC2005_REG_TEMP1 (0x5 << 3) +#define TSC2005_REG_TEMP2 (0x6 << 3) +#define TSC2005_REG_STATUS (0x7 << 3) +#define TSC2005_REG_AUX_HIGH (0x8 << 3) +#define TSC2005_REG_AUX_LOW (0x9 << 3) +#define TSC2005_REG_TEMP_HIGH (0xA << 3) +#define TSC2005_REG_TEMP_LOW (0xB << 3) +#define TSC2005_REG_CFR0 (0xC << 3) +#define TSC2005_REG_CFR1 (0xD << 3) +#define TSC2005_REG_CFR2 (0xE << 3) +#define TSC2005_REG_CONV_FUNC (0xF << 3) /* configuration register 0 */ #define TSC2005_CFR0_PRECHARGE_276US 0x0040 @@ -112,20 +121,37 @@ #define TSC2005_SPI_MAX_SPEED_HZ 10000000 #define TSC2005_PENUP_TIME_MS 40 -struct tsc2005_spi_rd { - struct spi_transfer spi_xfer; - u32 spi_tx; - u32 spi_rx; +static const struct regmap_range tsc2005_writable_ranges[] = { + regmap_reg_range(TSC2005_REG_AUX_HIGH, TSC2005_REG_CFR2), }; +static const struct regmap_access_table tsc2005_writable_table = { + .yes_ranges = tsc2005_writable_ranges, + .n_yes_ranges = ARRAY_SIZE(tsc2005_writable_ranges), +}; + +static struct regmap_config tsc2005_regmap_config = { + .reg_bits = 8, + .val_bits = 16, + .reg_stride = 0x08, + .max_register = 0x78, + .read_flag_mask = TSC2005_REG_READ, + .write_flag_mask = TSC2005_REG_PND0, + .wr_table = &tsc2005_writable_table, + .use_single_rw = true, +}; + +struct tsc2005_data { + u16 x; + u16 y; + u16 z1; + u16 z2; +} __packed; +#define TSC2005_DATA_REGS 4 + struct tsc2005 { struct spi_device *spi; - - struct spi_message spi_read_msg; - struct tsc2005_spi_rd spi_x; - struct tsc2005_spi_rd spi_y; - struct tsc2005_spi_rd spi_z1; - struct tsc2005_spi_rd spi_z2; + struct regmap *regmap; struct input_dev *idev; char phys[32]; @@ -154,7 +180,7 @@ struct tsc2005 { struct regulator *vio; - int reset_gpio; + struct gpio_desc *reset_gpio; void (*set_reset)(bool enable); }; @@ -182,62 +208,6 @@ static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd) return 0; } -static int tsc2005_write(struct tsc2005 *ts, u8 reg, u16 value) -{ - u32 tx = ((reg | TSC2005_REG_PND0) << 16) | value; - struct spi_transfer xfer = { - .tx_buf = &tx, - .len = 4, - .bits_per_word = 24, - }; - struct spi_message msg; - int error; - - spi_message_init(&msg); - spi_message_add_tail(&xfer, &msg); - - error = spi_sync(ts->spi, &msg); - if (error) { - dev_err(&ts->spi->dev, - "%s: failed, register: %x, value: %x, error: %d\n", - __func__, reg, value, error); - return error; - } - - return 0; -} - -static void tsc2005_setup_read(struct tsc2005_spi_rd *rd, u8 reg, bool last) -{ - memset(rd, 0, sizeof(*rd)); - - rd->spi_tx = (reg | TSC2005_REG_READ) << 16; - rd->spi_xfer.tx_buf = &rd->spi_tx; - rd->spi_xfer.rx_buf = &rd->spi_rx; - rd->spi_xfer.len = 4; - rd->spi_xfer.bits_per_word = 24; - rd->spi_xfer.cs_change = !last; -} - -static int tsc2005_read(struct tsc2005 *ts, u8 reg, u16 *value) -{ - struct tsc2005_spi_rd spi_rd; - struct spi_message msg; - int error; - - tsc2005_setup_read(&spi_rd, reg, true); - - spi_message_init(&msg); - spi_message_add_tail(&spi_rd.spi_xfer, &msg); - - error = spi_sync(ts->spi, &msg); - if (error) - return error; - - *value = spi_rd.spi_rx; - return 0; -} - static void tsc2005_update_pen_state(struct tsc2005 *ts, int x, int y, int pressure) { @@ -266,26 +236,23 @@ static irqreturn_t tsc2005_irq_thread(int irq, void *_ts) struct tsc2005 *ts = _ts; unsigned long flags; unsigned int pressure; - u32 x, y; - u32 z1, z2; + struct tsc2005_data tsdata; int error; /* read the coordinates */ - error = spi_sync(ts->spi, &ts->spi_read_msg); + error = regmap_bulk_read(ts->regmap, TSC2005_REG_X, &tsdata, + TSC2005_DATA_REGS); if (unlikely(error)) goto out; - x = ts->spi_x.spi_rx; - y = ts->spi_y.spi_rx; - z1 = ts->spi_z1.spi_rx; - z2 = ts->spi_z2.spi_rx; - /* validate position */ - if (unlikely(x > MAX_12BIT || y > MAX_12BIT)) + if (unlikely(tsdata.x > MAX_12BIT || tsdata.y > MAX_12BIT)) goto out; /* Skip reading if the pressure components are out of range */ - if (unlikely(z1 == 0 || z2 > MAX_12BIT || z1 >= z2)) + if (unlikely(tsdata.z1 == 0 || tsdata.z2 > MAX_12BIT)) + goto out; + if (unlikely(tsdata.z1 >= tsdata.z2)) goto out; /* @@ -293,8 +260,8 @@ static irqreturn_t tsc2005_irq_thread(int irq, void *_ts) * the value before pen-up - that implies SPI fed us stale data */ if (!ts->pen_down && - ts->in_x == x && ts->in_y == y && - ts->in_z1 == z1 && ts->in_z2 == z2) { + ts->in_x == tsdata.x && ts->in_y == tsdata.y && + ts->in_z1 == tsdata.z1 && ts->in_z2 == tsdata.z2) { goto out; } @@ -302,20 +269,20 @@ static irqreturn_t tsc2005_irq_thread(int irq, void *_ts) * At this point we are happy we have a valid and useful reading. * Remember it for later comparisons. We may now begin downsampling. */ - ts->in_x = x; - ts->in_y = y; - ts->in_z1 = z1; - ts->in_z2 = z2; + ts->in_x = tsdata.x; + ts->in_y = tsdata.y; + ts->in_z1 = tsdata.z1; + ts->in_z2 = tsdata.z2; /* Compute touch pressure resistance using equation #1 */ - pressure = x * (z2 - z1) / z1; + pressure = tsdata.x * (tsdata.z2 - tsdata.z1) / tsdata.z1; pressure = pressure * ts->x_plate_ohm / 4096; if (unlikely(pressure > MAX_12BIT)) goto out; spin_lock_irqsave(&ts->lock, flags); - tsc2005_update_pen_state(ts, x, y, pressure); + tsc2005_update_pen_state(ts, tsdata.x, tsdata.y, pressure); mod_timer(&ts->penup_timer, jiffies + msecs_to_jiffies(TSC2005_PENUP_TIME_MS)); @@ -338,9 +305,9 @@ static void tsc2005_penup_timer(unsigned long data) static void tsc2005_start_scan(struct tsc2005 *ts) { - tsc2005_write(ts, TSC2005_REG_CFR0, TSC2005_CFR0_INITVALUE); - tsc2005_write(ts, TSC2005_REG_CFR1, TSC2005_CFR1_INITVALUE); - tsc2005_write(ts, TSC2005_REG_CFR2, TSC2005_CFR2_INITVALUE); + regmap_write(ts->regmap, TSC2005_REG_CFR0, TSC2005_CFR0_INITVALUE); + regmap_write(ts->regmap, TSC2005_REG_CFR1, TSC2005_CFR1_INITVALUE); + regmap_write(ts->regmap, TSC2005_REG_CFR2, TSC2005_CFR2_INITVALUE); tsc2005_cmd(ts, TSC2005_CMD_NORMAL); } @@ -351,8 +318,8 @@ static void tsc2005_stop_scan(struct tsc2005 *ts) static void tsc2005_set_reset(struct tsc2005 *ts, bool enable) { - if (ts->reset_gpio >= 0) - gpio_set_value(ts->reset_gpio, enable); + if (ts->reset_gpio) + gpiod_set_value_cansleep(ts->reset_gpio, enable); else if (ts->set_reset) ts->set_reset(enable); } @@ -388,11 +355,10 @@ static ssize_t tsc2005_selftest_show(struct device *dev, struct device_attribute *attr, char *buf) { - struct spi_device *spi = to_spi_device(dev); - struct tsc2005 *ts = spi_get_drvdata(spi); - u16 temp_high; - u16 temp_high_orig; - u16 temp_high_test; + struct tsc2005 *ts = dev_get_drvdata(dev); + unsigned int temp_high; + unsigned int temp_high_orig; + unsigned int temp_high_test; bool success = true; int error; @@ -403,7 +369,7 @@ static ssize_t tsc2005_selftest_show(struct device *dev, */ __tsc2005_disable(ts); - error = tsc2005_read(ts, TSC2005_REG_TEMP_HIGH, &temp_high_orig); + error = regmap_read(ts->regmap, TSC2005_REG_TEMP_HIGH, &temp_high_orig); if (error) { dev_warn(dev, "selftest failed: read error %d\n", error); success = false; @@ -412,14 +378,14 @@ static ssize_t tsc2005_selftest_show(struct device *dev, temp_high_test = (temp_high_orig - 1) & MAX_12BIT; - error = tsc2005_write(ts, TSC2005_REG_TEMP_HIGH, temp_high_test); + error = regmap_write(ts->regmap, TSC2005_REG_TEMP_HIGH, temp_high_test); if (error) { dev_warn(dev, "selftest failed: write error %d\n", error); success = false; goto out; } - error = tsc2005_read(ts, TSC2005_REG_TEMP_HIGH, &temp_high); + error = regmap_read(ts->regmap, TSC2005_REG_TEMP_HIGH, &temp_high); if (error) { dev_warn(dev, "selftest failed: read error %d after write\n", error); @@ -442,7 +408,7 @@ static ssize_t tsc2005_selftest_show(struct device *dev, goto out; /* test that the reset really happened */ - error = tsc2005_read(ts, TSC2005_REG_TEMP_HIGH, &temp_high); + error = regmap_read(ts->regmap, TSC2005_REG_TEMP_HIGH, &temp_high); if (error) { dev_warn(dev, "selftest failed: read error %d after reset\n", error); @@ -474,8 +440,7 @@ static umode_t tsc2005_attr_is_visible(struct kobject *kobj, struct attribute *attr, int n) { struct device *dev = container_of(kobj, struct device, kobj); - struct spi_device *spi = to_spi_device(dev); - struct tsc2005 *ts = spi_get_drvdata(spi); + struct tsc2005 *ts = dev_get_drvdata(dev); umode_t mode = attr->mode; if (attr == &dev_attr_selftest.attr) { @@ -495,7 +460,7 @@ static void tsc2005_esd_work(struct work_struct *work) { struct tsc2005 *ts = container_of(work, struct tsc2005, esd_work.work); int error; - u16 r; + unsigned int r; if (!mutex_trylock(&ts->mutex)) { /* @@ -511,7 +476,7 @@ static void tsc2005_esd_work(struct work_struct *work) goto out; /* We should be able to read register without disabling interrupts. */ - error = tsc2005_read(ts, TSC2005_REG_CFR0, &r); + error = regmap_read(ts->regmap, TSC2005_REG_CFR0, &r); if (!error && !((r ^ TSC2005_CFR0_INITVALUE) & TSC2005_CFR0_RW_MASK)) { goto out; @@ -575,20 +540,6 @@ static void tsc2005_close(struct input_dev *input) mutex_unlock(&ts->mutex); } -static void tsc2005_setup_spi_xfer(struct tsc2005 *ts) -{ - tsc2005_setup_read(&ts->spi_x, TSC2005_REG_X, false); - tsc2005_setup_read(&ts->spi_y, TSC2005_REG_Y, false); - tsc2005_setup_read(&ts->spi_z1, TSC2005_REG_Z1, false); - tsc2005_setup_read(&ts->spi_z2, TSC2005_REG_Z2, true); - - spi_message_init(&ts->spi_read_msg); - spi_message_add_tail(&ts->spi_x.spi_xfer, &ts->spi_read_msg); - spi_message_add_tail(&ts->spi_y.spi_xfer, &ts->spi_read_msg); - spi_message_add_tail(&ts->spi_z1.spi_xfer, &ts->spi_read_msg); - spi_message_add_tail(&ts->spi_z2.spi_xfer, &ts->spi_read_msg); -} - static int tsc2005_probe(struct spi_device *spi) { const struct tsc2005_platform_data *pdata = dev_get_platdata(&spi->dev); @@ -653,37 +604,30 @@ static int tsc2005_probe(struct spi_device *spi) ts->spi = spi; ts->idev = input_dev; + ts->regmap = devm_regmap_init_spi(spi, &tsc2005_regmap_config); + if (IS_ERR(ts->regmap)) + return PTR_ERR(ts->regmap); + ts->x_plate_ohm = x_plate_ohm; ts->esd_timeout = esd_timeout; - if (np) { - ts->reset_gpio = of_get_named_gpio(np, "reset-gpios", 0); - if (ts->reset_gpio == -EPROBE_DEFER) - return ts->reset_gpio; - if (ts->reset_gpio < 0) { - dev_err(&spi->dev, "error acquiring reset gpio: %d\n", - ts->reset_gpio); - return ts->reset_gpio; - } + ts->reset_gpio = devm_gpiod_get_optional(&spi->dev, "reset", + GPIOD_OUT_HIGH); + if (IS_ERR(ts->reset_gpio)) { + error = PTR_ERR(ts->reset_gpio); + dev_err(&spi->dev, "error acquiring reset gpio: %d\n", error); + return error; + } - error = devm_gpio_request_one(&spi->dev, ts->reset_gpio, 0, - "reset-gpios"); - if (error) { - dev_err(&spi->dev, "error requesting reset gpio: %d\n", - error); - return error; - } + ts->vio = devm_regulator_get_optional(&spi->dev, "vio"); + if (IS_ERR(ts->vio)) { + error = PTR_ERR(ts->vio); + dev_err(&spi->dev, "vio regulator missing (%d)", error); + return error; + } - ts->vio = devm_regulator_get(&spi->dev, "vio"); - if (IS_ERR(ts->vio)) { - error = PTR_ERR(ts->vio); - dev_err(&spi->dev, "vio regulator missing (%d)", error); - return error; - } - } else { - ts->reset_gpio = -1; + if (!ts->reset_gpio && pdata) ts->set_reset = pdata->set_reset; - } mutex_init(&ts->mutex); @@ -692,8 +636,6 @@ static int tsc2005_probe(struct spi_device *spi) INIT_DELAYED_WORK(&ts->esd_work, tsc2005_esd_work); - tsc2005_setup_spi_xfer(ts); - snprintf(ts->phys, sizeof(ts->phys), "%s/input-ts", dev_name(&spi->dev)); @@ -709,7 +651,7 @@ static int tsc2005_probe(struct spi_device *spi) input_set_abs_params(input_dev, ABS_PRESSURE, 0, max_p, fudge_p, 0); if (np) - touchscreen_parse_of_params(input_dev, false); + touchscreen_parse_properties(input_dev, false); input_dev->open = tsc2005_open; input_dev->close = tsc2005_close; @@ -735,7 +677,7 @@ static int tsc2005_probe(struct spi_device *spi) return error; } - spi_set_drvdata(spi, ts); + dev_set_drvdata(&spi->dev, ts); error = sysfs_create_group(&spi->dev.kobj, &tsc2005_attr_group); if (error) { dev_err(&spi->dev, @@ -763,7 +705,7 @@ disable_regulator: static int tsc2005_remove(struct spi_device *spi) { - struct tsc2005 *ts = spi_get_drvdata(spi); + struct tsc2005 *ts = dev_get_drvdata(&spi->dev); sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group); @@ -775,8 +717,7 @@ static int tsc2005_remove(struct spi_device *spi) static int __maybe_unused tsc2005_suspend(struct device *dev) { - struct spi_device *spi = to_spi_device(dev); - struct tsc2005 *ts = spi_get_drvdata(spi); + struct tsc2005 *ts = dev_get_drvdata(dev); mutex_lock(&ts->mutex); @@ -792,8 +733,7 @@ static int __maybe_unused tsc2005_suspend(struct device *dev) static int __maybe_unused tsc2005_resume(struct device *dev) { - struct spi_device *spi = to_spi_device(dev); - struct tsc2005 *ts = spi_get_drvdata(spi); + struct tsc2005 *ts = dev_get_drvdata(dev); mutex_lock(&ts->mutex); |