diff options
Diffstat (limited to 'drivers/infiniband/hw/ipath/ipath_iba7220.c')
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_iba7220.c | 2631 |
1 files changed, 0 insertions, 2631 deletions
diff --git a/drivers/infiniband/hw/ipath/ipath_iba7220.c b/drivers/infiniband/hw/ipath/ipath_iba7220.c deleted file mode 100644 index 34b778e..0000000 --- a/drivers/infiniband/hw/ipath/ipath_iba7220.c +++ /dev/null @@ -1,2631 +0,0 @@ -/* - * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved. - * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. - * - * This software is available to you under a choice of one of two - * licenses. You may choose to be licensed under the terms of the GNU - * General Public License (GPL) Version 2, available from the file - * COPYING in the main directory of this source tree, or the - * OpenIB.org BSD license below: - * - * Redistribution and use in source and binary forms, with or - * without modification, are permitted provided that the following - * conditions are met: - * - * - Redistributions of source code must retain the above - * copyright notice, this list of conditions and the following - * disclaimer. - * - * - Redistributions in binary form must reproduce the above - * copyright notice, this list of conditions and the following - * disclaimer in the documentation and/or other materials - * provided with the distribution. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF - * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS - * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN - * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN - * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE - * SOFTWARE. - */ -/* - * This file contains all of the code that is specific to the - * InfiniPath 7220 chip (except that specific to the SerDes) - */ - -#include <linux/interrupt.h> -#include <linux/pci.h> -#include <linux/sched.h> -#include <linux/delay.h> -#include <linux/io.h> -#include <rdma/ib_verbs.h> - -#include "ipath_kernel.h" -#include "ipath_registers.h" -#include "ipath_7220.h" - -static void ipath_setup_7220_setextled(struct ipath_devdata *, u64, u64); - -static unsigned ipath_compat_ddr_negotiate = 1; - -module_param_named(compat_ddr_negotiate, ipath_compat_ddr_negotiate, uint, - S_IWUSR | S_IRUGO); -MODULE_PARM_DESC(compat_ddr_negotiate, - "Attempt pre-IBTA 1.2 DDR speed negotiation"); - -static unsigned ipath_sdma_fetch_arb = 1; -module_param_named(fetch_arb, ipath_sdma_fetch_arb, uint, S_IRUGO); -MODULE_PARM_DESC(fetch_arb, "IBA7220: change SDMA descriptor arbitration"); - -/* - * This file contains almost all the chip-specific register information and - * access functions for the QLogic InfiniPath 7220 PCI-Express chip, with the - * exception of SerDes support, which in in ipath_sd7220.c. - * - * This lists the InfiniPath registers, in the actual chip layout. - * This structure should never be directly accessed. - */ -struct _infinipath_do_not_use_kernel_regs { - unsigned long long Revision; - unsigned long long Control; - unsigned long long PageAlign; - unsigned long long PortCnt; - unsigned long long DebugPortSelect; - unsigned long long DebugSigsIntSel; /* was Reserved0;*/ - unsigned long long SendRegBase; - unsigned long long UserRegBase; - unsigned long long CounterRegBase; - unsigned long long Scratch; - unsigned long long EEPROMAddrCmd; /* was Reserved1; */ - unsigned long long EEPROMData; /* was Reserved2; */ - unsigned long long IntBlocked; - unsigned long long IntMask; - unsigned long long IntStatus; - unsigned long long IntClear; - unsigned long long ErrorMask; - unsigned long long ErrorStatus; - unsigned long long ErrorClear; - unsigned long long HwErrMask; - unsigned long long HwErrStatus; - unsigned long long HwErrClear; - unsigned long long HwDiagCtrl; - unsigned long long MDIO; - unsigned long long IBCStatus; - unsigned long long IBCCtrl; - unsigned long long ExtStatus; - unsigned long long ExtCtrl; - unsigned long long GPIOOut; - unsigned long long GPIOMask; - unsigned long long GPIOStatus; - unsigned long long GPIOClear; - unsigned long long RcvCtrl; - unsigned long long RcvBTHQP; - unsigned long long RcvHdrSize; - unsigned long long RcvHdrCnt; - unsigned long long RcvHdrEntSize; - unsigned long long RcvTIDBase; - unsigned long long RcvTIDCnt; - unsigned long long RcvEgrBase; - unsigned long long RcvEgrCnt; - unsigned long long RcvBufBase; - unsigned long long RcvBufSize; - unsigned long long RxIntMemBase; - unsigned long long RxIntMemSize; - unsigned long long RcvPartitionKey; - unsigned long long RcvQPMulticastPort; - unsigned long long RcvPktLEDCnt; - unsigned long long IBCDDRCtrl; - unsigned long long HRTBT_GUID; - unsigned long long IB_SDTEST_IF_TX; - unsigned long long IB_SDTEST_IF_RX; - unsigned long long IBCDDRCtrl2; - unsigned long long IBCDDRStatus; - unsigned long long JIntReload; - unsigned long long IBNCModeCtrl; - unsigned long long SendCtrl; - unsigned long long SendBufBase; - unsigned long long SendBufSize; - unsigned long long SendBufCnt; - unsigned long long SendAvailAddr; - unsigned long long TxIntMemBase; - unsigned long long TxIntMemSize; - unsigned long long SendDmaBase; - unsigned long long SendDmaLenGen; - unsigned long long SendDmaTail; - unsigned long long SendDmaHead; - unsigned long long SendDmaHeadAddr; - unsigned long long SendDmaBufMask0; - unsigned long long SendDmaBufMask1; - unsigned long long SendDmaBufMask2; - unsigned long long SendDmaStatus; - unsigned long long SendBufferError; - unsigned long long SendBufferErrorCONT1; - unsigned long long SendBufErr2; /* was Reserved6SBE[0/6] */ - unsigned long long Reserved6L[2]; - unsigned long long AvailUpdCount; - unsigned long long RcvHdrAddr0; - unsigned long long RcvHdrAddrs[16]; /* Why enumerate? */ - unsigned long long Reserved7hdtl; /* Align next to 300 */ - unsigned long long RcvHdrTailAddr0; /* 300, like others */ - unsigned long long RcvHdrTailAddrs[16]; - unsigned long long Reserved9SW[7]; /* was [8]; we have 17 ports */ - unsigned long long IbsdEpbAccCtl; /* IB Serdes EPB access control */ - unsigned long long IbsdEpbTransReg; /* IB Serdes EPB Transaction */ - unsigned long long Reserved10sds; /* was SerdesStatus on */ - unsigned long long XGXSConfig; - unsigned long long IBSerDesCtrl; /* Was IBPLLCfg on Monty */ - unsigned long long EEPCtlStat; /* for "boot" EEPROM/FLASH */ - unsigned long long EEPAddrCmd; - unsigned long long EEPData; - unsigned long long PcieEpbAccCtl; - unsigned long long PcieEpbTransCtl; - unsigned long long EfuseCtl; /* E-Fuse control */ - unsigned long long EfuseData[4]; - unsigned long long ProcMon; - /* this chip moves following two from previous 200, 208 */ - unsigned long long PCIeRBufTestReg0; - unsigned long long PCIeRBufTestReg1; - /* added for this chip */ - unsigned long long PCIeRBufTestReg2; - unsigned long long PCIeRBufTestReg3; - /* added for this chip, debug only */ - unsigned long long SPC_JTAG_ACCESS_REG; - unsigned long long LAControlReg; - unsigned long long GPIODebugSelReg; - unsigned long long DebugPortValueReg; - /* added for this chip, DMA */ - unsigned long long SendDmaBufUsed[3]; - unsigned long long SendDmaReqTagUsed; - /* - * added for this chip, EFUSE: note that these program 64-bit - * words 2 and 3 */ - unsigned long long efuse_pgm_data[2]; - unsigned long long Reserved11LAalign[10]; /* Skip 4B0..4F8 */ - /* we have 30 regs for DDS and RXEQ in IB SERDES */ - unsigned long long SerDesDDSRXEQ[30]; - unsigned long long Reserved12LAalign[2]; /* Skip 5F0, 5F8 */ - /* added for LA debug support */ - unsigned long long LAMemory[32]; -}; - -struct _infinipath_do_not_use_counters { - __u64 LBIntCnt; - __u64 LBFlowStallCnt; - __u64 TxSDmaDescCnt; /* was Reserved1 */ - __u64 TxUnsupVLErrCnt; - __u64 TxDataPktCnt; - __u64 TxFlowPktCnt; - __u64 TxDwordCnt; - __u64 TxLenErrCnt; - __u64 TxMaxMinLenErrCnt; - __u64 TxUnderrunCnt; - __u64 TxFlowStallCnt; - __u64 TxDroppedPktCnt; - __u64 RxDroppedPktCnt; - __u64 RxDataPktCnt; - __u64 RxFlowPktCnt; - __u64 RxDwordCnt; - __u64 RxLenErrCnt; - __u64 RxMaxMinLenErrCnt; - __u64 RxICRCErrCnt; - __u64 RxVCRCErrCnt; - __u64 RxFlowCtrlErrCnt; - __u64 RxBadFormatCnt; - __u64 RxLinkProblemCnt; - __u64 RxEBPCnt; - __u64 RxLPCRCErrCnt; - __u64 RxBufOvflCnt; - __u64 RxTIDFullErrCnt; - __u64 RxTIDValidErrCnt; - __u64 RxPKeyMismatchCnt; - __u64 RxP0HdrEgrOvflCnt; - __u64 RxP1HdrEgrOvflCnt; - __u64 RxP2HdrEgrOvflCnt; - __u64 RxP3HdrEgrOvflCnt; - __u64 RxP4HdrEgrOvflCnt; - __u64 RxP5HdrEgrOvflCnt; - __u64 RxP6HdrEgrOvflCnt; - __u64 RxP7HdrEgrOvflCnt; - __u64 RxP8HdrEgrOvflCnt; - __u64 RxP9HdrEgrOvflCnt; /* was Reserved6 */ - __u64 RxP10HdrEgrOvflCnt; /* was Reserved7 */ - __u64 RxP11HdrEgrOvflCnt; /* new for IBA7220 */ - __u64 RxP12HdrEgrOvflCnt; /* new for IBA7220 */ - __u64 RxP13HdrEgrOvflCnt; /* new for IBA7220 */ - __u64 RxP14HdrEgrOvflCnt; /* new for IBA7220 */ - __u64 RxP15HdrEgrOvflCnt; /* new for IBA7220 */ - __u64 RxP16HdrEgrOvflCnt; /* new for IBA7220 */ - __u64 IBStatusChangeCnt; - __u64 IBLinkErrRecoveryCnt; - __u64 IBLinkDownedCnt; - __u64 IBSymbolErrCnt; - /* The following are new for IBA7220 */ - __u64 RxVL15DroppedPktCnt; - __u64 RxOtherLocalPhyErrCnt; - __u64 PcieRetryBufDiagQwordCnt; - __u64 ExcessBufferOvflCnt; - __u64 LocalLinkIntegrityErrCnt; - __u64 RxVlErrCnt; - __u64 RxDlidFltrCnt; - __u64 Reserved8[7]; - __u64 PSStat; - __u64 PSStart; - __u64 PSInterval; - __u64 PSRcvDataCount; - __u64 PSRcvPktsCount; - __u64 PSXmitDataCount; - __u64 PSXmitPktsCount; - __u64 PSXmitWaitCount; -}; - -#define IPATH_KREG_OFFSET(field) (offsetof( \ - struct _infinipath_do_not_use_kernel_regs, field) / sizeof(u64)) -#define IPATH_CREG_OFFSET(field) (offsetof( \ - struct _infinipath_do_not_use_counters, field) / sizeof(u64)) - -static const struct ipath_kregs ipath_7220_kregs = { - .kr_control = IPATH_KREG_OFFSET(Control), - .kr_counterregbase = IPATH_KREG_OFFSET(CounterRegBase), - .kr_debugportselect = IPATH_KREG_OFFSET(DebugPortSelect), - .kr_errorclear = IPATH_KREG_OFFSET(ErrorClear), - .kr_errormask = IPATH_KREG_OFFSET(ErrorMask), - .kr_errorstatus = IPATH_KREG_OFFSET(ErrorStatus), - .kr_extctrl = IPATH_KREG_OFFSET(ExtCtrl), - .kr_extstatus = IPATH_KREG_OFFSET(ExtStatus), - .kr_gpio_clear = IPATH_KREG_OFFSET(GPIOClear), - .kr_gpio_mask = IPATH_KREG_OFFSET(GPIOMask), - .kr_gpio_out = IPATH_KREG_OFFSET(GPIOOut), - .kr_gpio_status = IPATH_KREG_OFFSET(GPIOStatus), - .kr_hwdiagctrl = IPATH_KREG_OFFSET(HwDiagCtrl), - .kr_hwerrclear = IPATH_KREG_OFFSET(HwErrClear), - .kr_hwerrmask = IPATH_KREG_OFFSET(HwErrMask), - .kr_hwerrstatus = IPATH_KREG_OFFSET(HwErrStatus), - .kr_ibcctrl = IPATH_KREG_OFFSET(IBCCtrl), - .kr_ibcstatus = IPATH_KREG_OFFSET(IBCStatus), - .kr_intblocked = IPATH_KREG_OFFSET(IntBlocked), - .kr_intclear = IPATH_KREG_OFFSET(IntClear), - .kr_intmask = IPATH_KREG_OFFSET(IntMask), - .kr_intstatus = IPATH_KREG_OFFSET(IntStatus), - .kr_mdio = IPATH_KREG_OFFSET(MDIO), - .kr_pagealign = IPATH_KREG_OFFSET(PageAlign), - .kr_partitionkey = IPATH_KREG_OFFSET(RcvPartitionKey), - .kr_portcnt = IPATH_KREG_OFFSET(PortCnt), - .kr_rcvbthqp = IPATH_KREG_OFFSET(RcvBTHQP), - .kr_rcvbufbase = IPATH_KREG_OFFSET(RcvBufBase), - .kr_rcvbufsize = IPATH_KREG_OFFSET(RcvBufSize), - .kr_rcvctrl = IPATH_KREG_OFFSET(RcvCtrl), - .kr_rcvegrbase = IPATH_KREG_OFFSET(RcvEgrBase), - .kr_rcvegrcnt = IPATH_KREG_OFFSET(RcvEgrCnt), - .kr_rcvhdrcnt = IPATH_KREG_OFFSET(RcvHdrCnt), - .kr_rcvhdrentsize = IPATH_KREG_OFFSET(RcvHdrEntSize), - .kr_rcvhdrsize = IPATH_KREG_OFFSET(RcvHdrSize), - .kr_rcvintmembase = IPATH_KREG_OFFSET(RxIntMemBase), - .kr_rcvintmemsize = IPATH_KREG_OFFSET(RxIntMemSize), - .kr_rcvtidbase = IPATH_KREG_OFFSET(RcvTIDBase), - .kr_rcvtidcnt = IPATH_KREG_OFFSET(RcvTIDCnt), - .kr_revision = IPATH_KREG_OFFSET(Revision), - .kr_scratch = IPATH_KREG_OFFSET(Scratch), - .kr_sendbuffererror = IPATH_KREG_OFFSET(SendBufferError), - .kr_sendctrl = IPATH_KREG_OFFSET(SendCtrl), - .kr_sendpioavailaddr = IPATH_KREG_OFFSET(SendAvailAddr), - .kr_sendpiobufbase = IPATH_KREG_OFFSET(SendBufBase), - .kr_sendpiobufcnt = IPATH_KREG_OFFSET(SendBufCnt), - .kr_sendpiosize = IPATH_KREG_OFFSET(SendBufSize), - .kr_sendregbase = IPATH_KREG_OFFSET(SendRegBase), - .kr_txintmembase = IPATH_KREG_OFFSET(TxIntMemBase), - .kr_txintmemsize = IPATH_KREG_OFFSET(TxIntMemSize), - .kr_userregbase = IPATH_KREG_OFFSET(UserRegBase), - - .kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig), - - /* send dma related regs */ - .kr_senddmabase = IPATH_KREG_OFFSET(SendDmaBase), - .kr_senddmalengen = IPATH_KREG_OFFSET(SendDmaLenGen), - .kr_senddmatail = IPATH_KREG_OFFSET(SendDmaTail), - .kr_senddmahead = IPATH_KREG_OFFSET(SendDmaHead), - .kr_senddmaheadaddr = IPATH_KREG_OFFSET(SendDmaHeadAddr), - .kr_senddmabufmask0 = IPATH_KREG_OFFSET(SendDmaBufMask0), - .kr_senddmabufmask1 = IPATH_KREG_OFFSET(SendDmaBufMask1), - .kr_senddmabufmask2 = IPATH_KREG_OFFSET(SendDmaBufMask2), - .kr_senddmastatus = IPATH_KREG_OFFSET(SendDmaStatus), - - /* SerDes related regs */ - .kr_ibserdesctrl = IPATH_KREG_OFFSET(IBSerDesCtrl), - .kr_ib_epbacc = IPATH_KREG_OFFSET(IbsdEpbAccCtl), - .kr_ib_epbtrans = IPATH_KREG_OFFSET(IbsdEpbTransReg), - .kr_pcie_epbacc = IPATH_KREG_OFFSET(PcieEpbAccCtl), - .kr_pcie_epbtrans = IPATH_KREG_OFFSET(PcieEpbTransCtl), - .kr_ib_ddsrxeq = IPATH_KREG_OFFSET(SerDesDDSRXEQ), - - /* - * These should not be used directly via ipath_read_kreg64(), - * use them with ipath_read_kreg64_port() - */ - .kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0), - .kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0), - - /* - * The rcvpktled register controls one of the debug port signals, so - * a packet activity LED can be connected to it. - */ - .kr_rcvpktledcnt = IPATH_KREG_OFFSET(RcvPktLEDCnt), - .kr_pcierbuftestreg0 = IPATH_KREG_OFFSET(PCIeRBufTestReg0), - .kr_pcierbuftestreg1 = IPATH_KREG_OFFSET(PCIeRBufTestReg1), - - .kr_hrtbt_guid = IPATH_KREG_OFFSET(HRTBT_GUID), - .kr_ibcddrctrl = IPATH_KREG_OFFSET(IBCDDRCtrl), - .kr_ibcddrstatus = IPATH_KREG_OFFSET(IBCDDRStatus), - .kr_jintreload = IPATH_KREG_OFFSET(JIntReload) -}; - -static const struct ipath_cregs ipath_7220_cregs = { - .cr_badformatcnt = IPATH_CREG_OFFSET(RxBadFormatCnt), - .cr_erricrccnt = IPATH_CREG_OFFSET(RxICRCErrCnt), - .cr_errlinkcnt = IPATH_CREG_OFFSET(RxLinkProblemCnt), - .cr_errlpcrccnt = IPATH_CREG_OFFSET(RxLPCRCErrCnt), - .cr_errpkey = IPATH_CREG_OFFSET(RxPKeyMismatchCnt), - .cr_errrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowCtrlErrCnt), - .cr_err_rlencnt = IPATH_CREG_OFFSET(RxLenErrCnt), - .cr_errslencnt = IPATH_CREG_OFFSET(TxLenErrCnt), - .cr_errtidfull = IPATH_CREG_OFFSET(RxTIDFullErrCnt), - .cr_errtidvalid = IPATH_CREG_OFFSET(RxTIDValidErrCnt), - .cr_errvcrccnt = IPATH_CREG_OFFSET(RxVCRCErrCnt), - .cr_ibstatuschange = IPATH_CREG_OFFSET(IBStatusChangeCnt), - .cr_intcnt = IPATH_CREG_OFFSET(LBIntCnt), - .cr_invalidrlencnt = IPATH_CREG_OFFSET(RxMaxMinLenErrCnt), - .cr_invalidslencnt = IPATH_CREG_OFFSET(TxMaxMinLenErrCnt), - .cr_lbflowstallcnt = IPATH_CREG_OFFSET(LBFlowStallCnt), - .cr_pktrcvcnt = IPATH_CREG_OFFSET(RxDataPktCnt), - .cr_pktrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowPktCnt), - .cr_pktsendcnt = IPATH_CREG_OFFSET(TxDataPktCnt), - .cr_pktsendflowcnt = IPATH_CREG_OFFSET(TxFlowPktCnt), - .cr_portovflcnt = IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt), - .cr_rcvebpcnt = IPATH_CREG_OFFSET(RxEBPCnt), - .cr_rcvovflcnt = IPATH_CREG_OFFSET(RxBufOvflCnt), - .cr_senddropped = IPATH_CREG_OFFSET(TxDroppedPktCnt), - .cr_sendstallcnt = IPATH_CREG_OFFSET(TxFlowStallCnt), - .cr_sendunderruncnt = IPATH_CREG_OFFSET(TxUnderrunCnt), - .cr_wordrcvcnt = IPATH_CREG_OFFSET(RxDwordCnt), - .cr_wordsendcnt = IPATH_CREG_OFFSET(TxDwordCnt), - .cr_unsupvlcnt = IPATH_CREG_OFFSET(TxUnsupVLErrCnt), - .cr_rxdroppktcnt = IPATH_CREG_OFFSET(RxDroppedPktCnt), - .cr_iblinkerrrecovcnt = IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt), - .cr_iblinkdowncnt = IPATH_CREG_OFFSET(IBLinkDownedCnt), - .cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt), - .cr_vl15droppedpktcnt = IPATH_CREG_OFFSET(RxVL15DroppedPktCnt), - .cr_rxotherlocalphyerrcnt = - IPATH_CREG_OFFSET(RxOtherLocalPhyErrCnt), - .cr_excessbufferovflcnt = IPATH_CREG_OFFSET(ExcessBufferOvflCnt), - .cr_locallinkintegrityerrcnt = - IPATH_CREG_OFFSET(LocalLinkIntegrityErrCnt), - .cr_rxvlerrcnt = IPATH_CREG_OFFSET(RxVlErrCnt), - .cr_rxdlidfltrcnt = IPATH_CREG_OFFSET(RxDlidFltrCnt), - .cr_psstat = IPATH_CREG_OFFSET(PSStat), - .cr_psstart = IPATH_CREG_OFFSET(PSStart), - .cr_psinterval = IPATH_CREG_OFFSET(PSInterval), - .cr_psrcvdatacount = IPATH_CREG_OFFSET(PSRcvDataCount), - .cr_psrcvpktscount = IPATH_CREG_OFFSET(PSRcvPktsCount), - .cr_psxmitdatacount = IPATH_CREG_OFFSET(PSXmitDataCount), - .cr_psxmitpktscount = IPATH_CREG_OFFSET(PSXmitPktsCount), - .cr_psxmitwaitcount = IPATH_CREG_OFFSET(PSXmitWaitCount), -}; - -/* kr_control bits */ -#define INFINIPATH_C_RESET (1U<<7) - -/* kr_intstatus, kr_intclear, kr_intmask bits */ -#define INFINIPATH_I_RCVURG_MASK ((1ULL<<17)-1) -#define INFINIPATH_I_RCVURG_SHIFT 32 -#define INFINIPATH_I_RCVAVAIL_MASK ((1ULL<<17)-1) -#define INFINIPATH_I_RCVAVAIL_SHIFT 0 -#define INFINIPATH_I_SERDESTRIMDONE (1ULL<<27) - -/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */ -#define INFINIPATH_HWE_PCIEMEMPARITYERR_MASK 0x00000000000000ffULL -#define INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT 0 -#define INFINIPATH_HWE_PCIEPOISONEDTLP 0x0000000010000000ULL -#define INFINIPATH_HWE_PCIECPLTIMEOUT 0x0000000020000000ULL -#define INFINIPATH_HWE_PCIEBUSPARITYXTLH 0x0000000040000000ULL -#define INFINIPATH_HWE_PCIEBUSPARITYXADM 0x0000000080000000ULL -#define INFINIPATH_HWE_PCIEBUSPARITYRADM 0x0000000100000000ULL -#define INFINIPATH_HWE_COREPLL_FBSLIP 0x0080000000000000ULL -#define INFINIPATH_HWE_COREPLL_RFSLIP 0x0100000000000000ULL -#define INFINIPATH_HWE_PCIE1PLLFAILED 0x0400000000000000ULL -#define INFINIPATH_HWE_PCIE0PLLFAILED 0x0800000000000000ULL -#define INFINIPATH_HWE_SERDESPLLFAILED 0x1000000000000000ULL -/* specific to this chip */ -#define INFINIPATH_HWE_PCIECPLDATAQUEUEERR 0x0000000000000040ULL -#define INFINIPATH_HWE_PCIECPLHDRQUEUEERR 0x0000000000000080ULL -#define INFINIPATH_HWE_SDMAMEMREADERR 0x0000000010000000ULL -#define INFINIPATH_HWE_CLK_UC_PLLNOTLOCKED 0x2000000000000000ULL -#define INFINIPATH_HWE_PCIESERDESQ0PCLKNOTDETECT 0x0100000000000000ULL -#define INFINIPATH_HWE_PCIESERDESQ1PCLKNOTDETECT 0x0200000000000000ULL -#define INFINIPATH_HWE_PCIESERDESQ2PCLKNOTDETECT 0x0400000000000000ULL -#define INFINIPATH_HWE_PCIESERDESQ3PCLKNOTDETECT 0x0800000000000000ULL -#define INFINIPATH_HWE_DDSRXEQMEMORYPARITYERR 0x0000008000000000ULL -#define INFINIPATH_HWE_IB_UC_MEMORYPARITYERR 0x0000004000000000ULL -#define INFINIPATH_HWE_PCIE_UC_OCT0MEMORYPARITYERR 0x0000001000000000ULL -#define INFINIPATH_HWE_PCIE_UC_OCT1MEMORYPARITYERR 0x0000002000000000ULL - -#define IBA7220_IBCS_LINKTRAININGSTATE_MASK 0x1F -#define IBA7220_IBCS_LINKSTATE_SHIFT 5 -#define IBA7220_IBCS_LINKSPEED_SHIFT 8 -#define IBA7220_IBCS_LINKWIDTH_SHIFT 9 - -#define IBA7220_IBCC_LINKINITCMD_MASK 0x7ULL -#define IBA7220_IBCC_LINKCMD_SHIFT 19 -#define IBA7220_IBCC_MAXPKTLEN_SHIFT 21 - -/* kr_ibcddrctrl bits */ -#define IBA7220_IBC_DLIDLMC_MASK 0xFFFFFFFFUL -#define IBA7220_IBC_DLIDLMC_SHIFT 32 -#define IBA7220_IBC_HRTBT_MASK 3 -#define IBA7220_IBC_HRTBT_SHIFT 16 -#define IBA7220_IBC_HRTBT_ENB 0x10000UL -#define IBA7220_IBC_LANE_REV_SUPPORTED (1<<8) -#define IBA7220_IBC_LREV_MASK 1 -#define IBA7220_IBC_LREV_SHIFT 8 -#define IBA7220_IBC_RXPOL_MASK 1 -#define IBA7220_IBC_RXPOL_SHIFT 7 -#define IBA7220_IBC_WIDTH_SHIFT 5 -#define IBA7220_IBC_WIDTH_MASK 0x3 -#define IBA7220_IBC_WIDTH_1X_ONLY (0<<IBA7220_IBC_WIDTH_SHIFT) -#define IBA7220_IBC_WIDTH_4X_ONLY (1<<IBA7220_IBC_WIDTH_SHIFT) -#define IBA7220_IBC_WIDTH_AUTONEG (2<<IBA7220_IBC_WIDTH_SHIFT) -#define IBA7220_IBC_SPEED_AUTONEG (1<<1) -#define IBA7220_IBC_SPEED_SDR (1<<2) -#define IBA7220_IBC_SPEED_DDR (1<<3) -#define IBA7220_IBC_SPEED_AUTONEG_MASK (0x7<<1) -#define IBA7220_IBC_IBTA_1_2_MASK (1) - -/* kr_ibcddrstatus */ -/* link latency shift is 0, don't bother defining */ -#define IBA7220_DDRSTAT_LINKLAT_MASK 0x3ffffff - -/* kr_extstatus bits */ -#define INFINIPATH_EXTS_FREQSEL 0x2 -#define INFINIPATH_EXTS_SERDESSEL 0x4 -#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000 -#define INFINIPATH_EXTS_MEMBIST_DISABLED 0x0000000000008000 - -/* kr_xgxsconfig bits */ -#define INFINIPATH_XGXS_RESET 0x5ULL -#define INFINIPATH_XGXS_FC_SAFE (1ULL<<63) - -/* kr_rcvpktledcnt */ -#define IBA7220_LEDBLINK_ON_SHIFT 32 /* 4ns period on after packet */ -#define IBA7220_LEDBLINK_OFF_SHIFT 0 /* 4ns period off before next on */ - -#define _IPATH_GPIO_SDA_NUM 1 -#define _IPATH_GPIO_SCL_NUM 0 - -#define IPATH_GPIO_SDA (1ULL << \ - (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT)) -#define IPATH_GPIO_SCL (1ULL << \ - (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT)) - -#define IBA7220_R_INTRAVAIL_SHIFT 17 -#define IBA7220_R_TAILUPD_SHIFT 35 -#define IBA7220_R_PORTCFG_SHIFT 36 - -#define INFINIPATH_JINT_PACKETSHIFT 16 -#define INFINIPATH_JINT_DEFAULT_IDLE_TICKS 0 -#define INFINIPATH_JINT_DEFAULT_MAX_PACKETS 0 - -#define IBA7220_HDRHEAD_PKTINT_SHIFT 32 /* interrupt cnt in upper 32 bits */ - -/* - * the size bits give us 2^N, in KB units. 0 marks as invalid, - * and 7 is reserved. We currently use only 2KB and 4KB - */ -#define IBA7220_TID_SZ_SHIFT 37 /* shift to 3bit size selector */ -#define IBA7220_TID_SZ_2K (1UL<<IBA7220_TID_SZ_SHIFT) /* 2KB */ -#define IBA7220_TID_SZ_4K (2UL<<IBA7220_TID_SZ_SHIFT) /* 4KB */ -#define IBA7220_TID_PA_SHIFT 11U /* TID addr in chip stored w/o low bits */ - -#define IPATH_AUTONEG_TRIES 5 /* sequential retries to negotiate DDR */ - -static char int_type[16] = "auto"; -module_param_string(interrupt_type, int_type, sizeof(int_type), 0444); -MODULE_PARM_DESC(int_type, " interrupt_type=auto|force_msi|force_intx"); - -/* packet rate matching delay; chip has support */ -static u8 rate_to_delay[2][2] = { - /* 1x, 4x */ - { 8, 2 }, /* SDR */ - { 4, 1 } /* DDR */ -}; - -/* 7220 specific hardware errors... */ -static const struct ipath_hwerror_msgs ipath_7220_hwerror_msgs[] = { - INFINIPATH_HWE_MSG(PCIEPOISONEDTLP, "PCIe Poisoned TLP"), - INFINIPATH_HWE_MSG(PCIECPLTIMEOUT, "PCIe completion timeout"), - /* - * In practice, it's unlikely wthat we'll see PCIe PLL, or bus - * parity or memory parity error failures, because most likely we - * won't be able to talk to the core of the chip. Nonetheless, we - * might see them, if they are in parts of the PCIe core that aren't - * essential. - */ - INFINIPATH_HWE_MSG(PCIE1PLLFAILED, "PCIePLL1"), - INFINIPATH_HWE_MSG(PCIE0PLLFAILED, "PCIePLL0"), - INFINIPATH_HWE_MSG(PCIEBUSPARITYXTLH, "PCIe XTLH core parity"), - INFINIPATH_HWE_MSG(PCIEBUSPARITYXADM, "PCIe ADM TX core parity"), - INFINIPATH_HWE_MSG(PCIEBUSPARITYRADM, "PCIe ADM RX core parity"), - INFINIPATH_HWE_MSG(RXDSYNCMEMPARITYERR, "Rx Dsync"), - INFINIPATH_HWE_MSG(SERDESPLLFAILED, "SerDes PLL"), - INFINIPATH_HWE_MSG(PCIECPLDATAQUEUEERR, "PCIe cpl header queue"), - INFINIPATH_HWE_MSG(PCIECPLHDRQUEUEERR, "PCIe cpl data queue"), - INFINIPATH_HWE_MSG(SDMAMEMREADERR, "Send DMA memory read"), - INFINIPATH_HWE_MSG(CLK_UC_PLLNOTLOCKED, "uC PLL clock not locked"), - INFINIPATH_HWE_MSG(PCIESERDESQ0PCLKNOTDETECT, - "PCIe serdes Q0 no clock"), - INFINIPATH_HWE_MSG(PCIESERDESQ1PCLKNOTDETECT, - "PCIe serdes Q1 no clock"), - INFINIPATH_HWE_MSG(PCIESERDESQ2PCLKNOTDETECT, - "PCIe serdes Q2 no clock"), - INFINIPATH_HWE_MSG(PCIESERDESQ3PCLKNOTDETECT, - "PCIe serdes Q3 no clock"), - INFINIPATH_HWE_MSG(DDSRXEQMEMORYPARITYERR, - "DDS RXEQ memory parity"), - INFINIPATH_HWE_MSG(IB_UC_MEMORYPARITYERR, "IB uC memory parity"), - INFINIPATH_HWE_MSG(PCIE_UC_OCT0MEMORYPARITYERR, - "PCIe uC oct0 memory parity"), - INFINIPATH_HWE_MSG(PCIE_UC_OCT1MEMORYPARITYERR, - "PCIe uC oct1 memory parity"), -}; - -static void autoneg_work(struct work_struct *); - -/* - * the offset is different for different configured port numbers, since - * port0 is fixed in size, but others can vary. Make it a function to - * make the issue more obvious. -*/ -static inline u32 port_egrtid_idx(struct ipath_devdata *dd, unsigned port) -{ - return port ? dd->ipath_p0_rcvegrcnt + - (port-1) * dd->ipath_rcvegrcnt : 0; -} - -static void ipath_7220_txe_recover(struct ipath_devdata *dd) -{ - ++ipath_stats.sps_txeparity; - - dev_info(&dd->pcidev->dev, - "Recovering from TXE PIO parity error\n"); - ipath_disarm_senderrbufs(dd); -} - - -/** - * ipath_7220_handle_hwerrors - display hardware errors. - * @dd: the infinipath device - * @msg: the output buffer - * @msgl: the size of the output buffer - * - * Use same msg buffer as regular errors to avoid excessive stack - * use. Most hardware errors are catastrophic, but for right now, - * we'll print them and continue. We reuse the same message buffer as - * ipath_handle_errors() to avoid excessive stack usage. - */ -static void ipath_7220_handle_hwerrors(struct ipath_devdata *dd, char *msg, - size_t msgl) -{ - ipath_err_t hwerrs; - u32 bits, ctrl; - int isfatal = 0; - char bitsmsg[64]; - int log_idx; - - hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus); - if (!hwerrs) { - /* - * better than printing cofusing messages - * This seems to be related to clearing the crc error, or - * the pll error during init. - */ - ipath_cdbg(VERBOSE, "Called but no hardware errors set\n"); - goto bail; - } else if (hwerrs == ~0ULL) { - ipath_dev_err(dd, "Read of hardware error status failed " - "(all bits set); ignoring\n"); - goto bail; - } - ipath_stats.sps_hwerrs++; - - /* - * Always clear the error status register, except MEMBISTFAIL, - * regardless of whether we continue or stop using the chip. - * We want that set so we know it failed, even across driver reload. - * We'll still ignore it in the hwerrmask. We do this partly for - * diagnostics, but also for support. - */ - ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear, - hwerrs&~INFINIPATH_HWE_MEMBISTFAILED); - - hwerrs &= dd->ipath_hwerrmask; - - /* We log some errors to EEPROM, check if we have any of those. */ - for (log_idx = 0; log_idx < IPATH_EEP_LOG_CNT; ++log_idx) - if (hwerrs & dd->ipath_eep_st_masks[log_idx].hwerrs_to_log) - ipath_inc_eeprom_err(dd, log_idx, 1); - /* - * Make sure we get this much out, unless told to be quiet, - * or it's occurred within the last 5 seconds. - */ - if ((hwerrs & ~(dd->ipath_lasthwerror | - ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | - INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) - << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT))) || - (ipath_debug & __IPATH_VERBDBG)) - dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx " - "(cleared)\n", (unsigned long long) hwerrs); - dd->ipath_lasthwerror |= hwerrs; - - if (hwerrs & ~dd->ipath_hwe_bitsextant) - ipath_dev_err(dd, "hwerror interrupt with unknown errors " - "%llx set\n", (unsigned long long) - (hwerrs & ~dd->ipath_hwe_bitsextant)); - - if (hwerrs & INFINIPATH_HWE_IB_UC_MEMORYPARITYERR) - ipath_sd7220_clr_ibpar(dd); - - ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control); - if ((ctrl & INFINIPATH_C_FREEZEMODE) && !ipath_diag_inuse) { - /* - * Parity errors in send memory are recoverable by h/w - * just do housekeeping, exit freeze mode and continue. - */ - if (hwerrs & ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | - INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) - << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) { - ipath_7220_txe_recover(dd); - hwerrs &= ~((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | - INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) - << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT); - } - if (hwerrs) { - /* - * If any set that we aren't ignoring only make the - * complaint once, in case it's stuck or recurring, - * and we get here multiple times - * Force link down, so switch knows, and - * LEDs are turned off. - */ - if (dd->ipath_flags & IPATH_INITTED) { - ipath_set_linkstate(dd, IPATH_IB_LINKDOWN); - ipath_setup_7220_setextled(dd, - INFINIPATH_IBCS_L_STATE_DOWN, - INFINIPATH_IBCS_LT_STATE_DISABLED); - ipath_dev_err(dd, "Fatal Hardware Error " - "(freeze mode), no longer" - " usable, SN %.16s\n", - dd->ipath_serial); - isfatal = 1; - } - /* - * Mark as having had an error for driver, and also - * for /sys and status word mapped to user programs. - * This marks unit as not usable, until reset. - */ - *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY; - *dd->ipath_statusp |= IPATH_STATUS_HWERROR; - dd->ipath_flags &= ~IPATH_INITTED; - } else { - ipath_dbg("Clearing freezemode on ignored or " - "recovered hardware error\n"); - ipath_clear_freeze(dd); - } - } - - *msg = '\0'; - - if (hwerrs & INFINIPATH_HWE_MEMBISTFAILED) { - strlcat(msg, "[Memory BIST test failed, " - "InfiniPath hardware unusable]", msgl); - /* ignore from now on, so disable until driver reloaded */ - *dd->ipath_statusp |= IPATH_STATUS_HWERROR; - dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED; - ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask, - dd->ipath_hwerrmask); - } - - ipath_format_hwerrors(hwerrs, - ipath_7220_hwerror_msgs, - ARRAY_SIZE(ipath_7220_hwerror_msgs), - msg, msgl); - - if (hwerrs & (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK - << INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT)) { - bits = (u32) ((hwerrs >> - INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT) & - INFINIPATH_HWE_PCIEMEMPARITYERR_MASK); - snprintf(bitsmsg, sizeof bitsmsg, - "[PCIe Mem Parity Errs %x] ", bits); - strlcat(msg, bitsmsg, msgl); - } - -#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP | \ - INFINIPATH_HWE_COREPLL_RFSLIP) - - if (hwerrs & _IPATH_PLL_FAIL) { - snprintf(bitsmsg, sizeof bitsmsg, - "[PLL failed (%llx), InfiniPath hardware unusable]", - (unsigned long long) hwerrs & _IPATH_PLL_FAIL); - strlcat(msg, bitsmsg, msgl); - /* ignore from now on, so disable until driver reloaded */ - dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL); - ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask, - dd->ipath_hwerrmask); - } - - if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) { - /* - * If it occurs, it is left masked since the eternal - * interface is unused. - */ - dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED; - ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask, - dd->ipath_hwerrmask); - } - - ipath_dev_err(dd, "%s hardware error\n", msg); - /* - * For /sys status file. if no trailing } is copied, we'll - * know it was truncated. - */ - if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) - snprintf(dd->ipath_freezemsg, dd->ipath_freezelen, - "{%s}", msg); -bail:; -} - -/** - * ipath_7220_boardname - fill in the board name - * @dd: the infinipath device - * @name: the output buffer - * @namelen: the size of the output buffer - * - * info is based on the board revision register - */ -static int ipath_7220_boardname(struct ipath_devdata *dd, char *name, - size_t namelen) -{ - char *n = NULL; - u8 boardrev = dd->ipath_boardrev; - int ret; - - if (boardrev == 15) { - /* - * Emulator sometimes comes up all-ones, rather than zero. - */ - boardrev = 0; - dd->ipath_boardrev = boardrev; - } - switch (boardrev) { - case 0: - n = "InfiniPath_7220_Emulation"; - break; - case 1: - n = "InfiniPath_QLE7240"; - break; - case 2: - n = "InfiniPath_QLE7280"; - break; - case 3: - n = "InfiniPath_QLE7242"; - break; - case 4: - n = "InfiniPath_QEM7240"; - break; - case 5: - n = "InfiniPath_QMI7240"; - break; - case 6: - n = "InfiniPath_QMI7264"; - break; - case 7: - n = "InfiniPath_QMH7240"; - break; - case 8: - n = "InfiniPath_QME7240"; - break; - case 9: - n = "InfiniPath_QLE7250"; - break; - case 10: - n = "InfiniPath_QLE7290"; - break; - case 11: - n = "InfiniPath_QEM7250"; - break; - case 12: - n = "InfiniPath_QLE-Bringup"; - break; - default: - ipath_dev_err(dd, - "Don't yet know about board with ID %u\n", - boardrev); - snprintf(name, namelen, "Unknown_InfiniPath_PCIe_%u", - boardrev); - break; - } - if (n) - snprintf(name, namelen, "%s", n); - - if (dd->ipath_majrev != 5 || !dd->ipath_minrev || - dd->ipath_minrev > 2) { - ipath_dev_err(dd, "Unsupported InfiniPath hardware " - "revision %u.%u!\n", - dd->ipath_majrev, dd->ipath_minrev); - ret = 1; - } else if (dd->ipath_minrev == 1 && - !(dd->ipath_flags & IPATH_INITTED)) { - /* Rev1 chips are prototype. Complain at init, but allow use */ - ipath_dev_err(dd, "Unsupported hardware " - "revision %u.%u, Contact support@qlogic.com\n", - dd->ipath_majrev, dd->ipath_minrev); - ret = 0; - } else - ret = 0; - - /* - * Set here not in ipath_init_*_funcs because we have to do - * it after we can read chip registers. - */ - dd->ipath_ureg_align = 0x10000; /* 64KB alignment */ - - return ret; -} - -/** - * ipath_7220_init_hwerrors - enable hardware errors - * @dd: the infinipath device - * - * now that we have finished initializing everything that might reasonably - * cause a hardware error, and cleared those errors bits as they occur, - * we can enable hardware errors in the mask (potentially enabling - * freeze mode), and enable hardware errors as errors (along with - * everything else) in errormask - */ -static void ipath_7220_init_hwerrors(struct ipath_devdata *dd) -{ - ipath_err_t val; - u64 extsval; - - extsval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus); - - if (!(extsval & (INFINIPATH_EXTS_MEMBIST_ENDTEST | - INFINIPATH_EXTS_MEMBIST_DISABLED))) - ipath_dev_err(dd, "MemBIST did not complete!\n"); - if (extsval & INFINIPATH_EXTS_MEMBIST_DISABLED) - dev_info(&dd->pcidev->dev, "MemBIST is disabled.\n"); - - val = ~0ULL; /* barring bugs, all hwerrors become interrupts, */ - - if (!dd->ipath_boardrev) /* no PLL for Emulator */ - val &= ~INFINIPATH_HWE_SERDESPLLFAILED; - - if (dd->ipath_minrev == 1) - val &= ~(1ULL << 42); /* TXE LaunchFIFO Parity rev1 issue */ - - val &= ~INFINIPATH_HWE_IB_UC_MEMORYPARITYERR; - dd->ipath_hwerrmask = val; - - /* - * special trigger "error" is for debugging purposes. It - * works around a processor/chipset problem. The error - * interrupt allows us to count occurrences, but we don't - * want to pay the overhead for normal use. Emulation only - */ - if (!dd->ipath_boardrev) - dd->ipath_maskederrs = INFINIPATH_E_SENDSPECIALTRIGGER; -} - -/* - * All detailed interaction with the SerDes has been moved to ipath_sd7220.c - * - * The portion of IBA7220-specific bringup_serdes() that actually deals with - * registers and memory within the SerDes itself is ipath_sd7220_init(). - */ - -/** - * ipath_7220_bringup_serdes - bring up the serdes - * @dd: the infinipath device - */ -static int ipath_7220_bringup_serdes(struct ipath_devdata *dd) -{ - int ret = 0; - u64 val, prev_val, guid; - int was_reset; /* Note whether uC was reset */ - - ipath_dbg("Trying to bringup serdes\n"); - - if (ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus) & - INFINIPATH_HWE_SERDESPLLFAILED) { - ipath_dbg("At start, serdes PLL failed bit set " - "in hwerrstatus, clearing and continuing\n"); - ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear, - INFINIPATH_HWE_SERDESPLLFAILED); - } - - dd->ibdeltainprog = 1; - dd->ibsymsnap = - ipath_read_creg32(dd, dd->ipath_cregs->cr_ibsymbolerrcnt); - dd->iblnkerrsnap = - ipath_read_creg32(dd, dd->ipath_cregs->cr_iblinkerrrecovcnt); - - if (!dd->ipath_ibcddrctrl) { - /* not on re-init after reset */ - dd->ipath_ibcddrctrl = - ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcddrctrl); - - if (dd->ipath_link_speed_enabled == - (IPATH_IB_SDR | IPATH_IB_DDR)) - dd->ipath_ibcddrctrl |= - IBA7220_IBC_SPEED_AUTONEG_MASK | - IBA7220_IBC_IBTA_1_2_MASK; - else - dd->ipath_ibcddrctrl |= - dd->ipath_link_speed_enabled == IPATH_IB_DDR - ? IBA7220_IBC_SPEED_DDR : - IBA7220_IBC_SPEED_SDR; - if ((dd->ipath_link_width_enabled & (IB_WIDTH_1X | - IB_WIDTH_4X)) == (IB_WIDTH_1X | IB_WIDTH_4X)) - dd->ipath_ibcddrctrl |= IBA7220_IBC_WIDTH_AUTONEG; - else - dd->ipath_ibcddrctrl |= - dd->ipath_link_width_enabled == IB_WIDTH_4X - ? IBA7220_IBC_WIDTH_4X_ONLY : - IBA7220_IBC_WIDTH_1X_ONLY; - - /* always enable these on driver reload, not sticky */ - dd->ipath_ibcddrctrl |= - IBA7220_IBC_RXPOL_MASK << IBA7220_IBC_RXPOL_SHIFT; - dd->ipath_ibcddrctrl |= - IBA7220_IBC_HRTBT_MASK << IBA7220_IBC_HRTBT_SHIFT; - /* - * automatic lane reversal detection for receive - * doesn't work correctly in rev 1, so disable it - * on that rev, otherwise enable (disabling not - * sticky across reload for >rev1) - */ - if (dd->ipath_minrev == 1) - dd->ipath_ibcddrctrl &= - ~IBA7220_IBC_LANE_REV_SUPPORTED; - else - dd->ipath_ibcddrctrl |= - IBA7220_IBC_LANE_REV_SUPPORTED; - } - - ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcddrctrl, - dd->ipath_ibcddrctrl); - - ipath_write_kreg(dd, IPATH_KREG_OFFSET(IBNCModeCtrl), 0Ull); - - /* IBA7220 has SERDES MPU reset in D0 of what _was_ IBPLLCfg */ - val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibserdesctrl); - /* remember if uC was in Reset or not, for dactrim */ - was_reset = (val & 1); - ipath_cdbg(VERBOSE, "IBReset %s xgxsconfig %llx\n", - was_reset ? "Asserted" : "Negated", (unsigned long long) - ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig)); - - if (dd->ipath_boardrev) { - /* - * Hardware is not emulator, and may have been reset. Init it. - * Below will release reset, but needs to know if chip was - * originally in reset, to only trim DACs on first time - * after chip reset or powercycle (not driver reload) - */ - ret = ipath_sd7220_init(dd, was_reset); - } - - val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig); - prev_val = val; - val |= INFINIPATH_XGXS_FC_SAFE; - if (val != prev_val) { - ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val); - ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); - } - if (val & INFINIPATH_XGXS_RESET) - val &= ~INFINIPATH_XGXS_RESET; - if (val != prev_val) - ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val); - - ipath_cdbg(VERBOSE, "done: xgxs=%llx from %llx\n", - (unsigned long long) - ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig), - (unsigned long long) prev_val); - - guid = be64_to_cpu(dd->ipath_guid); - - if (!guid) { - /* have to have something, so use likely unique tsc */ - guid = get_cycles(); - ipath_dbg("No GUID for heartbeat, faking %llx\n", - (unsigned long long)guid); - } else - ipath_cdbg(VERBOSE, "Wrote %llX to HRTBT_GUID\n", - (unsigned long long) guid); - ipath_write_kreg(dd, dd->ipath_kregs->kr_hrtbt_guid, guid); - return ret; -} - -static void ipath_7220_config_jint(struct ipath_devdata *dd, - u16 idle_ticks, u16 max_packets) -{ - - /* - * We can request a receive interrupt for 1 or more packets - * from current offset. - */ - if (idle_ticks == 0 || max_packets == 0) - /* interrupt after one packet if no mitigation */ - dd->ipath_rhdrhead_intr_off = - 1ULL << IBA7220_HDRHEAD_PKTINT_SHIFT; - else - /* Turn off RcvHdrHead interrupts if using mitigation */ - dd->ipath_rhdrhead_intr_off = 0ULL; - - /* refresh kernel RcvHdrHead registers... */ - ipath_write_ureg(dd, ur_rcvhdrhead, - dd->ipath_rhdrhead_intr_off | - dd->ipath_pd[0]->port_head, 0); - - dd->ipath_jint_max_packets = max_packets; - dd->ipath_jint_idle_ticks = idle_ticks; - ipath_write_kreg(dd, dd->ipath_kregs->kr_jintreload, - ((u64) max_packets << INFINIPATH_JINT_PACKETSHIFT) | - idle_ticks); -} - -/** - * ipath_7220_quiet_serdes - set serdes to txidle - * @dd: the infinipath device - * Called when driver is being unloaded - */ -static void ipath_7220_quiet_serdes(struct ipath_devdata *dd) -{ - u64 val; - if (dd->ibsymdelta || dd->iblnkerrdelta || - dd->ibdeltainprog) { - u64 diagc; - /* enable counter writes */ - diagc = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwdiagctrl); - ipath_write_kreg(dd, dd->ipath_kregs->kr_hwdiagctrl, - diagc | INFINIPATH_DC_COUNTERWREN); - - if (dd->ibsymdelta || dd->ibdeltainprog) { - val = ipath_read_creg32(dd, - dd->ipath_cregs->cr_ibsymbolerrcnt); - if (dd->ibdeltainprog) - val -= val - dd->ibsymsnap; - val -= dd->ibsymdelta; - ipath_write_creg(dd, - dd->ipath_cregs->cr_ibsymbolerrcnt, val); - } - if (dd->iblnkerrdelta || dd->ibdeltainprog) { - val = ipath_read_creg32(dd, - dd->ipath_cregs->cr_iblinkerrrecovcnt); - if (dd->ibdeltainprog) - val -= val - dd->iblnkerrsnap; - val -= dd->iblnkerrdelta; - ipath_write_creg(dd, - dd->ipath_cregs->cr_iblinkerrrecovcnt, val); - } - - /* and disable counter writes */ - ipath_write_kreg(dd, dd->ipath_kregs->kr_hwdiagctrl, diagc); - } - - dd->ipath_flags &= ~IPATH_IB_AUTONEG_INPROG; - wake_up(&dd->ipath_autoneg_wait); - cancel_delayed_work(&dd->ipath_autoneg_work); - flush_scheduled_work(); - ipath_shutdown_relock_poll(dd); - val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig); - val |= INFINIPATH_XGXS_RESET; - ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val); -} - -static int ipath_7220_intconfig(struct ipath_devdata *dd) -{ - ipath_7220_config_jint(dd, dd->ipath_jint_idle_ticks, - dd->ipath_jint_max_packets); - return 0; -} - -/** - * ipath_setup_7220_setextled - set the state of the two external LEDs - * @dd: the infinipath device - * @lst: the L state - * @ltst: the LT state - * - * These LEDs indicate the physical and logical state of IB link. - * For this chip (at least with recommended board pinouts), LED1 - * is Yellow (logical state) and LED2 is Green (physical state), - * - * Note: We try to match the Mellanox HCA LED behavior as best - * we can. Green indicates physical link state is OK (something is - * plugged in, and we can train). - * Amber indicates the link is logically up (ACTIVE). - * Mellanox further blinks the amber LED to indicate data packet - * activity, but we have no hardware support for that, so it would - * require waking up every 10-20 msecs and checking the counters - * on the chip, and then turning the LED off if appropriate. That's - * visible overhead, so not something we will do. - * - */ -static void ipath_setup_7220_setextled(struct ipath_devdata *dd, u64 lst, - u64 ltst) -{ - u64 extctl, ledblink = 0; - unsigned long flags = 0; - - /* the diags use the LED to indicate diag info, so we leave - * the external LED alone when the diags are running */ - if (ipath_diag_inuse) - return; - - /* Allow override of LED display for, e.g. Locating system in rack */ - if (dd->ipath_led_override) { - ltst = (dd->ipath_led_override & IPATH_LED_PHYS) - ? INFINIPATH_IBCS_LT_STATE_LINKUP - : INFINIPATH_IBCS_LT_STATE_DISABLED; - lst = (dd->ipath_led_override & IPATH_LED_LOG) - ? INFINIPATH_IBCS_L_STATE_ACTIVE - : INFINIPATH_IBCS_L_STATE_DOWN; - } - - spin_lock_irqsave(&dd->ipath_gpio_lock, flags); - extctl = dd->ipath_extctrl & ~(INFINIPATH_EXTC_LED1PRIPORT_ON | - INFINIPATH_EXTC_LED2PRIPORT_ON); - if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP) { - extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON; - /* - * counts are in chip clock (4ns) periods. - * This is 1/16 sec (66.6ms) on, - * 3/16 sec (187.5 ms) off, with packets rcvd - */ - ledblink = ((66600*1000UL/4) << IBA7220_LEDBLINK_ON_SHIFT) - | ((187500*1000UL/4) << IBA7220_LEDBLINK_OFF_SHIFT); - } - if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE) - extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON; - dd->ipath_extctrl = extctl; - ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl); - spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags); - - if (ledblink) /* blink the LED on packet receive */ - ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvpktledcnt, - ledblink); -} - -/* - * Similar to pci_intx(pdev, 1), except that we make sure - * msi is off... - */ -static void ipath_enable_intx(struct pci_dev *pdev) -{ - u16 cw, new; - int pos; - - /* first, turn on INTx */ - pci_read_config_word(pdev, PCI_COMMAND, &cw); - new = cw & ~PCI_COMMAND_INTX_DISABLE; - if (new != cw) - pci_write_config_word(pdev, PCI_COMMAND, new); - - /* then turn off MSI */ - pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); - if (pos) { - pci_read_config_word(pdev, pos + PCI_MSI_FLAGS, &cw); - new = cw & ~PCI_MSI_FLAGS_ENABLE; - if (new != cw) - pci_write_config_word(pdev, pos + PCI_MSI_FLAGS, new); - } -} - -static int ipath_msi_enabled(struct pci_dev *pdev) -{ - int pos, ret = 0; - - pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); - if (pos) { - u16 cw; - - pci_read_config_word(pdev, pos + PCI_MSI_FLAGS, &cw); - ret = !!(cw & PCI_MSI_FLAGS_ENABLE); - } - return ret; -} - -/* - * disable msi interrupt if enabled, and clear the flag. - * flag is used primarily for the fallback to INTx, but - * is also used in reinit after reset as a flag. - */ -static void ipath_7220_nomsi(struct ipath_devdata *dd) -{ - dd->ipath_msi_lo = 0; - - if (ipath_msi_enabled(dd->pcidev)) { - /* - * free, but don't zero; later kernels require - * it be freed before disable_msi, so the intx - * setup has to request it again. - */ - if (dd->ipath_irq) - free_irq(dd->ipath_irq, dd); - pci_disable_msi(dd->pcidev); - } -} - -/* - * ipath_setup_7220_cleanup - clean up any per-chip chip-specific stuff - * @dd: the infinipath device - * - * Nothing but msi interrupt cleanup for now. - * - * This is called during driver unload. - */ -static void ipath_setup_7220_cleanup(struct ipath_devdata *dd) -{ - ipath_7220_nomsi(dd); -} - - -static void ipath_7220_pcie_params(struct ipath_devdata *dd, u32 boardrev) -{ - u16 linkstat, minwidth, speed; - int pos; - - pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP); - if (!pos) { - ipath_dev_err(dd, "Can't find PCI Express capability!\n"); - goto bail; - } - - pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA, - &linkstat); - /* - * speed is bits 0-4, linkwidth is bits 4-8 - * no defines for them in headers - */ - speed = linkstat & 0xf; - linkstat >>= 4; - linkstat &= 0x1f; - dd->ipath_lbus_width = linkstat; - switch (boardrev) { - case 0: - case 2: - case 10: - case 12: - minwidth = 16; /* x16 capable boards */ - break; - default: - minwidth = 8; /* x8 capable boards */ - break; - } - - switch (speed) { - case 1: - dd->ipath_lbus_speed = 2500; /* Gen1, 2.5GHz */ - break; - case 2: - dd->ipath_lbus_speed = 5000; /* Gen1, 5GHz */ - break; - default: /* not defined, assume gen1 */ - dd->ipath_lbus_speed = 2500; - break; - } - - if (linkstat < minwidth) - ipath_dev_err(dd, - "PCIe width %u (x%u HCA), performance " - "reduced\n", linkstat, minwidth); - else - ipath_cdbg(VERBOSE, "PCIe speed %u width %u (x%u HCA)\n", - dd->ipath_lbus_speed, linkstat, minwidth); - - if (speed != 1) - ipath_dev_err(dd, - "PCIe linkspeed %u is incorrect; " - "should be 1 (2500)!\n", speed); - -bail: - /* fill in string, even on errors */ - snprintf(dd->ipath_lbus_info, sizeof(dd->ipath_lbus_info), - "PCIe,%uMHz,x%u\n", - dd->ipath_lbus_speed, - dd->ipath_lbus_width); - return; -} - - -/** - * ipath_setup_7220_config - setup PCIe config related stuff - * @dd: the infinipath device - * @pdev: the PCI device - * - * The pci_enable_msi() call will fail on systems with MSI quirks - * such as those with AMD8131, even if the device of interest is not - * attached to that device, (in the 2.6.13 - 2.6.15 kernels, at least, fixed - * late in 2.6.16). - * All that can be done is to edit the kernel source to remove the quirk - * check until that is fixed. - * We do not need to call enable_msi() for our HyperTransport chip, - * even though it uses MSI, and we want to avoid the quirk warning, so - * So we call enable_msi only for PCIe. If we do end up needing - * pci_enable_msi at some point in the future for HT, we'll move the - * call back into the main init_one code. - * We save the msi lo and hi values, so we can restore them after - * chip reset (the kernel PCI infrastructure doesn't yet handle that - * correctly). - */ -static int ipath_setup_7220_config(struct ipath_devdata *dd, - struct pci_dev *pdev) -{ - int pos, ret = -1; - u32 boardrev; - - dd->ipath_msi_lo = 0; /* used as a flag during reset processing */ - - pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); - if (!strcmp(int_type, "force_msi") || !strcmp(int_type, "auto")) - ret = pci_enable_msi(pdev); - if (ret) { - if (!strcmp(int_type, "force_msi")) { - ipath_dev_err(dd, "pci_enable_msi failed: %d, " - "force_msi is on, so not continuing.\n", - ret); - return ret; - } - - ipath_enable_intx(pdev); - if (!strcmp(int_type, "auto")) - ipath_dev_err(dd, "pci_enable_msi failed: %d, " - "falling back to INTx\n", ret); - } else if (pos) { - u16 control; - pci_read_config_dword(pdev, pos + PCI_MSI_ADDRESS_LO, - &dd->ipath_msi_lo); - pci_read_config_dword(pdev, pos + PCI_MSI_ADDRESS_HI, - &dd->ipath_msi_hi); - pci_read_config_word(pdev, pos + PCI_MSI_FLAGS, - &control); - /* now save the data (vector) info */ - pci_read_config_word(pdev, - pos + ((control & PCI_MSI_FLAGS_64BIT) - ? PCI_MSI_DATA_64 : - PCI_MSI_DATA_32), - &dd->ipath_msi_data); - } else - ipath_dev_err(dd, "Can't find MSI capability, " - "can't save MSI settings for reset\n"); - - dd->ipath_irq = pdev->irq; - - /* - * We save the cachelinesize also, although it doesn't - * really matter. - */ - pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, - &dd->ipath_pci_cacheline); - - /* - * this function called early, ipath_boardrev not set yet. Can't - * use ipath_read_kreg64() yet, too early in init, so use readq() - */ - boardrev = (readq(&dd->ipath_kregbase[dd->ipath_kregs->kr_revision]) - >> INFINIPATH_R_BOARDID_SHIFT) & INFINIPATH_R_BOARDID_MASK; - - ipath_7220_pcie_params(dd, boardrev); - - dd->ipath_flags |= IPATH_NODMA_RTAIL | IPATH_HAS_SEND_DMA | - IPATH_HAS_PBC_CNT | IPATH_HAS_THRESH_UPDATE; - dd->ipath_pioupd_thresh = 4U; /* set default update threshold */ - return 0; -} - -static void ipath_init_7220_variables(struct ipath_devdata *dd) -{ - /* - * setup the register offsets, since they are different for each - * chip - */ - dd->ipath_kregs = &ipath_7220_kregs; - dd->ipath_cregs = &ipath_7220_cregs; - - /* - * bits for selecting i2c direction and values, - * used for I2C serial flash - */ - dd->ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM; - dd->ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM; - dd->ipath_gpio_sda = IPATH_GPIO_SDA; - dd->ipath_gpio_scl = IPATH_GPIO_SCL; - - /* - * Fill in data for field-values that change in IBA7220. - * We dynamically specify only the mask for LINKTRAININGSTATE - * and only the shift for LINKSTATE, as they are the only ones - * that change. Also precalculate the 3 link states of interest - * and the combined mask. - */ - dd->ibcs_ls_shift = IBA7220_IBCS_LINKSTATE_SHIFT; - dd->ibcs_lts_mask = IBA7220_IBCS_LINKTRAININGSTATE_MASK; - dd->ibcs_mask = (INFINIPATH_IBCS_LINKSTATE_MASK << - dd->ibcs_ls_shift) | dd->ibcs_lts_mask; - dd->ib_init = (INFINIPATH_IBCS_LT_STATE_LINKUP << - INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) | - (INFINIPATH_IBCS_L_STATE_INIT << dd->ibcs_ls_shift); - dd->ib_arm = (INFINIPATH_IBCS_LT_STATE_LINKUP << - INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) | - (INFINIPATH_IBCS_L_STATE_ARM << dd->ibcs_ls_shift); - dd->ib_active = (INFINIPATH_IBCS_LT_STATE_LINKUP << - INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) | - (INFINIPATH_IBCS_L_STATE_ACTIVE << dd->ibcs_ls_shift); - - /* - * Fill in data for ibcc field-values that change in IBA7220. - * We dynamically specify only the mask for LINKINITCMD - * and only the shift for LINKCMD and MAXPKTLEN, as they are - * the only ones that change. - */ - dd->ibcc_lic_mask = IBA7220_IBCC_LINKINITCMD_MASK; - dd->ibcc_lc_shift = IBA7220_IBCC_LINKCMD_SHIFT; - dd->ibcc_mpl_shift = IBA7220_IBCC_MAXPKTLEN_SHIFT; - - /* Fill in shifts for RcvCtrl. */ - dd->ipath_r_portenable_shift = INFINIPATH_R_PORTENABLE_SHIFT; - dd->ipath_r_intravail_shift = IBA7220_R_INTRAVAIL_SHIFT; - dd->ipath_r_tailupd_shift = IBA7220_R_TAILUPD_SHIFT; - dd->ipath_r_portcfg_shift = IBA7220_R_PORTCFG_SHIFT; - - /* variables for sanity checking interrupt and errors */ - dd->ipath_hwe_bitsextant = - (INFINIPATH_HWE_RXEMEMPARITYERR_MASK << - INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) | - (INFINIPATH_HWE_TXEMEMPARITYERR_MASK << - INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) | - (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK << - INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT) | - INFINIPATH_HWE_PCIE1PLLFAILED | - INFINIPATH_HWE_PCIE0PLLFAILED | - INFINIPATH_HWE_PCIEPOISONEDTLP | - INFINIPATH_HWE_PCIECPLTIMEOUT | - INFINIPATH_HWE_PCIEBUSPARITYXTLH | - INFINIPATH_HWE_PCIEBUSPARITYXADM | - INFINIPATH_HWE_PCIEBUSPARITYRADM | - INFINIPATH_HWE_MEMBISTFAILED | - INFINIPATH_HWE_COREPLL_FBSLIP | - INFINIPATH_HWE_COREPLL_RFSLIP | - INFINIPATH_HWE_SERDESPLLFAILED | - INFINIPATH_HWE_IBCBUSTOSPCPARITYERR | - INFINIPATH_HWE_IBCBUSFRSPCPARITYERR | - INFINIPATH_HWE_PCIECPLDATAQUEUEERR | - INFINIPATH_HWE_PCIECPLHDRQUEUEERR | - INFINIPATH_HWE_SDMAMEMREADERR | - INFINIPATH_HWE_CLK_UC_PLLNOTLOCKED | - INFINIPATH_HWE_PCIESERDESQ0PCLKNOTDETECT | - INFINIPATH_HWE_PCIESERDESQ1PCLKNOTDETECT | - INFINIPATH_HWE_PCIESERDESQ2PCLKNOTDETECT | - INFINIPATH_HWE_PCIESERDESQ3PCLKNOTDETECT | - INFINIPATH_HWE_DDSRXEQMEMORYPARITYERR | - INFINIPATH_HWE_IB_UC_MEMORYPARITYERR | - INFINIPATH_HWE_PCIE_UC_OCT0MEMORYPARITYERR | - INFINIPATH_HWE_PCIE_UC_OCT1MEMORYPARITYERR; - dd->ipath_i_bitsextant = - INFINIPATH_I_SDMAINT | INFINIPATH_I_SDMADISABLED | - (INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) | - (INFINIPATH_I_RCVAVAIL_MASK << - INFINIPATH_I_RCVAVAIL_SHIFT) | - INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT | - INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO | - INFINIPATH_I_JINT | INFINIPATH_I_SERDESTRIMDONE; - dd->ipath_e_bitsextant = - INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC | - INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN | - INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN | - INFINIPATH_E_RSHORTPKTLEN | INFINIPATH_E_RUNEXPCHAR | - INFINIPATH_E_RUNSUPVL | INFINIPATH_E_REBP | - INFINIPATH_E_RIBFLOW | INFINIPATH_E_RBADVERSION | - INFINIPATH_E_RRCVEGRFULL | INFINIPATH_E_RRCVHDRFULL | - INFINIPATH_E_RBADTID | INFINIPATH_E_RHDRLEN | - INFINIPATH_E_RHDR | INFINIPATH_E_RIBLOSTLINK | - INFINIPATH_E_SENDSPECIALTRIGGER | - INFINIPATH_E_SDMADISABLED | INFINIPATH_E_SMINPKTLEN | - INFINIPATH_E_SMAXPKTLEN | INFINIPATH_E_SUNDERRUN | - INFINIPATH_E_SPKTLEN | INFINIPATH_E_SDROPPEDSMPPKT | - INFINIPATH_E_SDROPPEDDATAPKT | - INFINIPATH_E_SPIOARMLAUNCH | INFINIPATH_E_SUNEXPERRPKTNUM | - INFINIPATH_E_SUNSUPVL | INFINIPATH_E_SENDBUFMISUSE | - INFINIPATH_E_SDMAGENMISMATCH | INFINIPATH_E_SDMAOUTOFBOUND | - INFINIPATH_E_SDMATAILOUTOFBOUND | INFINIPATH_E_SDMABASE | - INFINIPATH_E_SDMA1STDESC | INFINIPATH_E_SDMARPYTAG | - INFINIPATH_E_SDMADWEN | INFINIPATH_E_SDMAMISSINGDW | - INFINIPATH_E_SDMAUNEXPDATA | - INFINIPATH_E_IBSTATUSCHANGED | INFINIPATH_E_INVALIDADDR | - INFINIPATH_E_RESET | INFINIPATH_E_HARDWARE | - INFINIPATH_E_SDMADESCADDRMISALIGN | - INFINIPATH_E_INVALIDEEPCMD; - - dd->ipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK; - dd->ipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK; - dd->ipath_i_rcvavail_shift = INFINIPATH_I_RCVAVAIL_SHIFT; - dd->ipath_i_rcvurg_shift = INFINIPATH_I_RCVURG_SHIFT; - dd->ipath_flags |= IPATH_INTREG_64 | IPATH_HAS_MULT_IB_SPEED - | IPATH_HAS_LINK_LATENCY; - - /* - * EEPROM error log 0 is TXE Parity errors. 1 is RXE Parity. - * 2 is Some Misc, 3 is reserved for future. - */ - dd->ipath_eep_st_masks[0].hwerrs_to_log = - INFINIPATH_HWE_TXEMEMPARITYERR_MASK << - INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT; - - dd->ipath_eep_st_masks[1].hwerrs_to_log = - INFINIPATH_HWE_RXEMEMPARITYERR_MASK << - INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT; - - dd->ipath_eep_st_masks[2].errs_to_log = INFINIPATH_E_RESET; - - ipath_linkrecovery = 0; - - init_waitqueue_head(&dd->ipath_autoneg_wait); - INIT_DELAYED_WORK(&dd->ipath_autoneg_work, autoneg_work); - - dd->ipath_link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X; - dd->ipath_link_speed_supported = IPATH_IB_SDR | IPATH_IB_DDR; - - dd->ipath_link_width_enabled = dd->ipath_link_width_supported; - dd->ipath_link_speed_enabled = dd->ipath_link_speed_supported; - /* - * set the initial values to reasonable default, will be set - * for real when link is up. - */ - dd->ipath_link_width_active = IB_WIDTH_4X; - dd->ipath_link_speed_active = IPATH_IB_SDR; - dd->delay_mult = rate_to_delay[0][1]; -} - - -/* - * Setup the MSI stuff again after a reset. I'd like to just call - * pci_enable_msi() and request_irq() again, but when I do that, - * the MSI enable bit doesn't get set in the command word, and - * we switch to to a different interrupt vector, which is confusing, - * so I instead just do it all inline. Perhaps somehow can tie this - * into the PCIe hotplug support at some point - * Note, because I'm doing it all here, I don't call pci_disable_msi() - * or free_irq() at the start of ipath_setup_7220_reset(). - */ -static int ipath_reinit_msi(struct ipath_devdata *dd) -{ - int ret = 0; - - int pos; - u16 control; - if (!dd->ipath_msi_lo) /* Using intX, or init problem */ - goto bail; - - pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_MSI); - if (!pos) { - ipath_dev_err(dd, "Can't find MSI capability, " - "can't restore MSI settings\n"); - goto bail; - } - ipath_cdbg(VERBOSE, "Writing msi_lo 0x%x to config offset 0x%x\n", - dd->ipath_msi_lo, pos + PCI_MSI_ADDRESS_LO); - pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_LO, - dd->ipath_msi_lo); - ipath_cdbg(VERBOSE, "Writing msi_lo 0x%x to config offset 0x%x\n", - dd->ipath_msi_hi, pos + PCI_MSI_ADDRESS_HI); - pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_HI, - dd->ipath_msi_hi); - pci_read_config_word(dd->pcidev, pos + PCI_MSI_FLAGS, &control); - if (!(control & PCI_MSI_FLAGS_ENABLE)) { - ipath_cdbg(VERBOSE, "MSI control at off %x was %x, " - "setting MSI enable (%x)\n", pos + PCI_MSI_FLAGS, - control, control | PCI_MSI_FLAGS_ENABLE); - control |= PCI_MSI_FLAGS_ENABLE; - pci_write_config_word(dd->pcidev, pos + PCI_MSI_FLAGS, - control); - } - /* now rewrite the data (vector) info */ - pci_write_config_word(dd->pcidev, pos + - ((control & PCI_MSI_FLAGS_64BIT) ? 12 : 8), - dd->ipath_msi_data); - ret = 1; - -bail: - if (!ret) { - ipath_dbg("Using INTx, MSI disabled or not configured\n"); - ipath_enable_intx(dd->pcidev); - ret = 1; - } - /* - * We restore the cachelinesize also, although it doesn't really - * matter. - */ - pci_write_config_byte(dd->pcidev, PCI_CACHE_LINE_SIZE, - dd->ipath_pci_cacheline); - /* and now set the pci master bit again */ - pci_set_master(dd->pcidev); - - return ret; -} - -/* - * This routine sleeps, so it can only be called from user context, not - * from interrupt context. If we need interrupt context, we can split - * it into two routines. - */ -static int ipath_setup_7220_reset(struct ipath_devdata *dd) -{ - u64 val; - int i; - int ret; - u16 cmdval; - - pci_read_config_word(dd->pcidev, PCI_COMMAND, &cmdval); - - /* Use dev_err so it shows up in logs, etc. */ - ipath_dev_err(dd, "Resetting InfiniPath unit %u\n", dd->ipath_unit); - - /* keep chip from being accessed in a few places */ - dd->ipath_flags &= ~(IPATH_INITTED | IPATH_PRESENT); - val = dd->ipath_control | INFINIPATH_C_RESET; - ipath_write_kreg(dd, dd->ipath_kregs->kr_control, val); - mb(); - - for (i = 1; i <= 5; i++) { - int r; - - /* - * Allow MBIST, etc. to complete; longer on each retry. - * We sometimes get machine checks from bus timeout if no - * response, so for now, make it *really* long. - */ - msleep(1000 + (1 + i) * 2000); - r = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_0, - dd->ipath_pcibar0); - if (r) - ipath_dev_err(dd, "rewrite of BAR0 failed: %d\n", r); - r = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_1, - dd->ipath_pcibar1); - if (r) - ipath_dev_err(dd, "rewrite of BAR1 failed: %d\n", r); - /* now re-enable memory access */ - pci_write_config_word(dd->pcidev, PCI_COMMAND, cmdval); - r = pci_enable_device(dd->pcidev); - if (r) - ipath_dev_err(dd, "pci_enable_device failed after " - "reset: %d\n", r); - /* - * whether it fully enabled or not, mark as present, - * again (but not INITTED) - */ - dd->ipath_flags |= IPATH_PRESENT; - val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_revision); - if (val == dd->ipath_revision) { - ipath_cdbg(VERBOSE, "Got matching revision " - "register %llx on try %d\n", - (unsigned long long) val, i); - ret = ipath_reinit_msi(dd); - goto bail; - } - /* Probably getting -1 back */ - ipath_dbg("Didn't get expected revision register, " - "got %llx, try %d\n", (unsigned long long) val, - i + 1); - } - ret = 0; /* failed */ - -bail: - if (ret) - ipath_7220_pcie_params(dd, dd->ipath_boardrev); - - return ret; -} - -/** - * ipath_7220_put_tid - write a TID to the chip - * @dd: the infinipath device - * @tidptr: pointer to the expected TID (in chip) to update - * @tidtype: 0 for eager, 1 for expected - * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing - * - * This exists as a separate routine to allow for selection of the - * appropriate "flavor". The static calls in cleanup just use the - * revision-agnostic form, as they are not performance critical. - */ -static void ipath_7220_put_tid(struct ipath_devdata *dd, u64 __iomem *tidptr, - u32 type, unsigned long pa) -{ - if (pa != dd->ipath_tidinvalid) { - u64 chippa = pa >> IBA7220_TID_PA_SHIFT; - - /* paranoia checks */ - if (pa != (chippa << IBA7220_TID_PA_SHIFT)) { - dev_info(&dd->pcidev->dev, "BUG: physaddr %lx " - "not 2KB aligned!\n", pa); - return; - } - if (chippa >= (1UL << IBA7220_TID_SZ_SHIFT)) { - ipath_dev_err(dd, - "BUG: Physical page address 0x%lx " - "larger than supported\n", pa); - return; - } - - if (type == RCVHQ_RCV_TYPE_EAGER) - chippa |= dd->ipath_tidtemplate; - else /* for now, always full 4KB page */ - chippa |= IBA7220_TID_SZ_4K; - writeq(chippa, tidptr); - } else - writeq(pa, tidptr); - mmiowb(); -} - -/** - * ipath_7220_clear_tid - clear all TID entries for a port, expected and eager - * @dd: the infinipath device - * @port: the port - * - * clear all TID entries for a port, expected and eager. - * Used from ipath_close(). On this chip, TIDs are only 32 bits, - * not 64, but they are still on 64 bit boundaries, so tidbase - * is declared as u64 * for the pointer math, even though we write 32 bits - */ -static void ipath_7220_clear_tids(struct ipath_devdata *dd, unsigned port) -{ - u64 __iomem *tidbase; - unsigned long tidinv; - int i; - - if (!dd->ipath_kregbase) - return; - - ipath_cdbg(VERBOSE, "Invalidate TIDs for port %u\n", port); - - tidinv = dd->ipath_tidinvalid; - tidbase = (u64 __iomem *) - ((char __iomem *)(dd->ipath_kregbase) + - dd->ipath_rcvtidbase + - port * dd->ipath_rcvtidcnt * sizeof(*tidbase)); - - for (i = 0; i < dd->ipath_rcvtidcnt; i++) - ipath_7220_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EXPECTED, - tidinv); - - tidbase = (u64 __iomem *) - ((char __iomem *)(dd->ipath_kregbase) + - dd->ipath_rcvegrbase + port_egrtid_idx(dd, port) - * sizeof(*tidbase)); - - for (i = port ? dd->ipath_rcvegrcnt : dd->ipath_p0_rcvegrcnt; i; i--) - ipath_7220_put_tid(dd, &tidbase[i-1], RCVHQ_RCV_TYPE_EAGER, - tidinv); -} - -/** - * ipath_7220_tidtemplate - setup constants for TID updates - * @dd: the infinipath device - * - * We setup stuff that we use a lot, to avoid calculating each time - */ -static void ipath_7220_tidtemplate(struct ipath_devdata *dd) -{ - /* For now, we always allocate 4KB buffers (at init) so we can - * receive max size packets. We may want a module parameter to - * specify 2KB or 4KB and/or make be per port instead of per device - * for those who want to reduce memory footprint. Note that the - * ipath_rcvhdrentsize size must be large enough to hold the largest - * IB header (currently 96 bytes) that we expect to handle (plus of - * course the 2 dwords of RHF). - */ - if (dd->ipath_rcvegrbufsize == 2048) - dd->ipath_tidtemplate = IBA7220_TID_SZ_2K; - else if (dd->ipath_rcvegrbufsize == 4096) - dd->ipath_tidtemplate = IBA7220_TID_SZ_4K; - else { - dev_info(&dd->pcidev->dev, "BUG: unsupported egrbufsize " - "%u, using %u\n", dd->ipath_rcvegrbufsize, - 4096); - dd->ipath_tidtemplate = IBA7220_TID_SZ_4K; - } - dd->ipath_tidinvalid = 0; -} - -static int ipath_7220_early_init(struct ipath_devdata *dd) -{ - u32 i, s; - - if (strcmp(int_type, "auto") && - strcmp(int_type, "force_msi") && - strcmp(int_type, "force_intx")) { - ipath_dev_err(dd, "Invalid interrupt_type: '%s', expecting " - "auto, force_msi or force_intx\n", int_type); - return -EINVAL; - } - - /* - * Control[4] has been added to change the arbitration within - * the SDMA engine between favoring data fetches over descriptor - * fetches. ipath_sdma_fetch_arb==0 gives data fetches priority. - */ - if (ipath_sdma_fetch_arb && (dd->ipath_minrev > 1)) - dd->ipath_control |= 1<<4; - - dd->ipath_flags |= IPATH_4BYTE_TID; - - /* - * For openfabrics, we need to be able to handle an IB header of - * 24 dwords. HT chip has arbitrary sized receive buffers, so we - * made them the same size as the PIO buffers. This chip does not - * handle arbitrary size buffers, so we need the header large enough - * to handle largest IB header, but still have room for a 2KB MTU - * standard IB packet. - */ - dd->ipath_rcvhdrentsize = 24; - dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE; - dd->ipath_rhf_offset = - dd->ipath_rcvhdrentsize - sizeof(u64) / sizeof(u32); - - dd->ipath_rcvegrbufsize = ipath_mtu4096 ? 4096 : 2048; - /* - * the min() check here is currently a nop, but it may not always - * be, depending on just how we do ipath_rcvegrbufsize - */ - dd->ipath_ibmaxlen = min(ipath_mtu4096 ? dd->ipath_piosize4k : - dd->ipath_piosize2k, - dd->ipath_rcvegrbufsize + - (dd->ipath_rcvhdrentsize << 2)); - dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen; - - ipath_7220_config_jint(dd, INFINIPATH_JINT_DEFAULT_IDLE_TICKS, - INFINIPATH_JINT_DEFAULT_MAX_PACKETS); - - if (dd->ipath_boardrev) /* no eeprom on emulator */ - ipath_get_eeprom_info(dd); - - /* start of code to check and print procmon */ - s = ipath_read_kreg32(dd, IPATH_KREG_OFFSET(ProcMon)); - s &= ~(1U<<31); /* clear done bit */ - s |= 1U<<14; /* clear counter (write 1 to clear) */ - ipath_write_kreg(dd, IPATH_KREG_OFFSET(ProcMon), s); - /* make sure clear_counter low long enough before start */ - ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); - ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); - - s &= ~(1U<<14); /* allow counter to count (before starting) */ - ipath_write_kreg(dd, IPATH_KREG_OFFSET(ProcMon), s); - ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); - ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); - s = ipath_read_kreg32(dd, IPATH_KREG_OFFSET(ProcMon)); - - s |= 1U<<15; /* start the counter */ - s &= ~(1U<<31); /* clear done bit */ - s &= ~0x7ffU; /* clear frequency bits */ - s |= 0xe29; /* set frequency bits, in case cleared */ - ipath_write_kreg(dd, IPATH_KREG_OFFSET(ProcMon), s); - - s = 0; - for (i = 500; i > 0 && !(s&(1ULL<<31)); i--) { - ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); - s = ipath_read_kreg32(dd, IPATH_KREG_OFFSET(ProcMon)); - } - if (!(s&(1U<<31))) - ipath_dev_err(dd, "ProcMon register not valid: 0x%x\n", s); - else - ipath_dbg("ProcMon=0x%x, count=0x%x\n", s, (s>>16)&0x1ff); - - return 0; -} - -/** - * ipath_init_7220_get_base_info - set chip-specific flags for user code - * @pd: the infinipath port - * @kbase: ipath_base_info pointer - * - * We set the PCIE flag because the lower bandwidth on PCIe vs - * HyperTransport can affect some user packet algorithims. - */ -static int ipath_7220_get_base_info(struct ipath_portdata *pd, void *kbase) -{ - struct ipath_base_info *kinfo = kbase; - - kinfo->spi_runtime_flags |= - IPATH_RUNTIME_PCIE | IPATH_RUNTIME_NODMA_RTAIL | - IPATH_RUNTIME_SDMA; - - return 0; -} - -static void ipath_7220_free_irq(struct ipath_devdata *dd) -{ - free_irq(dd->ipath_irq, dd); - dd->ipath_irq = 0; -} - -static struct ipath_message_header * -ipath_7220_get_msgheader(struct ipath_devdata *dd, __le32 *rhf_addr) -{ - u32 offset = ipath_hdrget_offset(rhf_addr); - - return (struct ipath_message_header *) - (rhf_addr - dd->ipath_rhf_offset + offset); -} - -static void ipath_7220_config_ports(struct ipath_devdata *dd, ushort cfgports) -{ - u32 nchipports; - - nchipports = ipath_read_kreg32(dd, dd->ipath_kregs->kr_portcnt); - if (!cfgports) { - int ncpus = num_online_cpus(); - - if (ncpus <= 4) - dd->ipath_portcnt = 5; - else if (ncpus <= 8) - dd->ipath_portcnt = 9; - if (dd->ipath_portcnt) - ipath_dbg("Auto-configured for %u ports, %d cpus " - "online\n", dd->ipath_portcnt, ncpus); - } else if (cfgports <= nchipports) - dd->ipath_portcnt = cfgports; - if (!dd->ipath_portcnt) /* none of the above, set to max */ - dd->ipath_portcnt = nchipports; - /* - * chip can be configured for 5, 9, or 17 ports, and choice - * affects number of eager TIDs per port (1K, 2K, 4K). - */ - if (dd->ipath_portcnt > 9) - dd->ipath_rcvctrl |= 2ULL << IBA7220_R_PORTCFG_SHIFT; - else if (dd->ipath_portcnt > 5) - dd->ipath_rcvctrl |= 1ULL << IBA7220_R_PORTCFG_SHIFT; - /* else configure for default 5 receive ports */ - ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvctrl, - dd->ipath_rcvctrl); - dd->ipath_p0_rcvegrcnt = 2048; /* always */ - if (dd->ipath_flags & IPATH_HAS_SEND_DMA) - dd->ipath_pioreserved = 3; /* kpiobufs used for PIO */ -} - - -static int ipath_7220_get_ib_cfg(struct ipath_devdata *dd, int which) -{ - int lsb, ret = 0; - u64 maskr; /* right-justified mask */ - - switch (which) { - case IPATH_IB_CFG_HRTBT: /* Get Heartbeat off/enable/auto */ - lsb = IBA7220_IBC_HRTBT_SHIFT; - maskr = IBA7220_IBC_HRTBT_MASK; - break; - - case IPATH_IB_CFG_LWID_ENB: /* Get allowed Link-width */ - ret = dd->ipath_link_width_enabled; - goto done; - - case IPATH_IB_CFG_LWID: /* Get currently active Link-width */ - ret = dd->ipath_link_width_active; - goto done; - - case IPATH_IB_CFG_SPD_ENB: /* Get allowed Link speeds */ - ret = dd->ipath_link_speed_enabled; - goto done; - - case IPATH_IB_CFG_SPD: /* Get current Link spd */ - ret = dd->ipath_link_speed_active; - goto done; - - case IPATH_IB_CFG_RXPOL_ENB: /* Get Auto-RX-polarity enable */ - lsb = IBA7220_IBC_RXPOL_SHIFT; - maskr = IBA7220_IBC_RXPOL_MASK; - break; - - case IPATH_IB_CFG_LREV_ENB: /* Get Auto-Lane-reversal enable */ - lsb = IBA7220_IBC_LREV_SHIFT; - maskr = IBA7220_IBC_LREV_MASK; - break; - - case IPATH_IB_CFG_LINKLATENCY: - ret = ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcddrstatus) - & IBA7220_DDRSTAT_LINKLAT_MASK; - goto done; - - default: - ret = -ENOTSUPP; - goto done; - } - ret = (int)((dd->ipath_ibcddrctrl >> lsb) & maskr); -done: - return ret; -} - -static int ipath_7220_set_ib_cfg(struct ipath_devdata *dd, int which, u32 val) -{ - int lsb, ret = 0, setforce = 0; - u64 maskr; /* right-justified mask */ - - switch (which) { - case IPATH_IB_CFG_LIDLMC: - /* - * Set LID and LMC. Combined to avoid possible hazard - * caller puts LMC in 16MSbits, DLID in 16LSbits of val - */ - lsb = IBA7220_IBC_DLIDLMC_SHIFT; - maskr = IBA7220_IBC_DLIDLMC_MASK; - break; - - case IPATH_IB_CFG_HRTBT: /* set Heartbeat off/enable/auto */ - if (val & IPATH_IB_HRTBT_ON && - (dd->ipath_flags & IPATH_NO_HRTBT)) - goto bail; - lsb = IBA7220_IBC_HRTBT_SHIFT; - maskr = IBA7220_IBC_HRTBT_MASK; - break; - - case IPATH_IB_CFG_LWID_ENB: /* set allowed Link-width */ - /* - * As with speed, only write the actual register if - * the link is currently down, otherwise takes effect - * on next link change. - */ - dd->ipath_link_width_enabled = val; - if ((dd->ipath_flags & (IPATH_LINKDOWN|IPATH_LINKINIT)) != - IPATH_LINKDOWN) - goto bail; - /* - * We set the IPATH_IB_FORCE_NOTIFY bit so updown - * will get called because we want update - * link_width_active, and the change may not take - * effect for some time (if we are in POLL), so this - * flag will force the updown routine to be called - * on the next ibstatuschange down interrupt, even - * if it's not an down->up transition. - */ - val--; /* convert from IB to chip */ - maskr = IBA7220_IBC_WIDTH_MASK; - lsb = IBA7220_IBC_WIDTH_SHIFT; - setforce = 1; - dd->ipath_flags |= IPATH_IB_FORCE_NOTIFY; - break; - - case IPATH_IB_CFG_SPD_ENB: /* set allowed Link speeds */ - /* - * If we turn off IB1.2, need to preset SerDes defaults, - * but not right now. Set a flag for the next time - * we command the link down. As with width, only write the - * actual register if the link is currently down, otherwise - * takes effect on next link change. Since setting is being - * explictly requested (via MAD or sysfs), clear autoneg - * failure status if speed autoneg is enabled. - */ - dd->ipath_link_speed_enabled = val; - if (dd->ipath_ibcddrctrl & IBA7220_IBC_IBTA_1_2_MASK && - !(val & (val - 1))) - dd->ipath_presets_needed = 1; - if ((dd->ipath_flags & (IPATH_LINKDOWN|IPATH_LINKINIT)) != - IPATH_LINKDOWN) - goto bail; - /* - * We set the IPATH_IB_FORCE_NOTIFY bit so updown - * will get called because we want update - * link_speed_active, and the change may not take - * effect for some time (if we are in POLL), so this - * flag will force the updown routine to be called - * on the next ibstatuschange down interrupt, even - * if it's not an down->up transition. When setting - * speed autoneg, clear AUTONEG_FAILED. - */ - if (val == (IPATH_IB_SDR | IPATH_IB_DDR)) { - val = IBA7220_IBC_SPEED_AUTONEG_MASK | - IBA7220_IBC_IBTA_1_2_MASK; - dd->ipath_flags &= ~IPATH_IB_AUTONEG_FAILED; - } else - val = val == IPATH_IB_DDR ? IBA7220_IBC_SPEED_DDR - : IBA7220_IBC_SPEED_SDR; - maskr = IBA7220_IBC_SPEED_AUTONEG_MASK | - IBA7220_IBC_IBTA_1_2_MASK; - lsb = 0; /* speed bits are low bits */ - setforce = 1; - break; - - case IPATH_IB_CFG_RXPOL_ENB: /* set Auto-RX-polarity enable */ - lsb = IBA7220_IBC_RXPOL_SHIFT; - maskr = IBA7220_IBC_RXPOL_MASK; - break; - - case IPATH_IB_CFG_LREV_ENB: /* set Auto-Lane-reversal enable */ - lsb = IBA7220_IBC_LREV_SHIFT; - maskr = IBA7220_IBC_LREV_MASK; - break; - - default: - ret = -ENOTSUPP; - goto bail; - } - dd->ipath_ibcddrctrl &= ~(maskr << lsb); - dd->ipath_ibcddrctrl |= (((u64) val & maskr) << lsb); - ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcddrctrl, - dd->ipath_ibcddrctrl); - if (setforce) - dd->ipath_flags |= IPATH_IB_FORCE_NOTIFY; -bail: - return ret; -} - -static void ipath_7220_read_counters(struct ipath_devdata *dd, - struct infinipath_counters *cntrs) -{ - u64 *counters = (u64 *) cntrs; - int i; - - for (i = 0; i < sizeof(*cntrs) / sizeof(u64); i++) - counters[i] = ipath_snap_cntr(dd, i); -} - -/* if we are using MSI, try to fallback to INTx */ -static int ipath_7220_intr_fallback(struct ipath_devdata *dd) -{ - if (dd->ipath_msi_lo) { - dev_info(&dd->pcidev->dev, "MSI interrupt not detected," - " trying INTx interrupts\n"); - ipath_7220_nomsi(dd); - ipath_enable_intx(dd->pcidev); - /* - * some newer kernels require free_irq before disable_msi, - * and irq can be changed during disable and intx enable - * and we need to therefore use the pcidev->irq value, - * not our saved MSI value. - */ - dd->ipath_irq = dd->pcidev->irq; - if (request_irq(dd->ipath_irq, ipath_intr, IRQF_SHARED, - IPATH_DRV_NAME, dd)) - ipath_dev_err(dd, - "Could not re-request_irq for INTx\n"); - return 1; - } - return 0; -} - -/* - * reset the XGXS (between serdes and IBC). Slightly less intrusive - * than resetting the IBC or external link state, and useful in some - * cases to cause some retraining. To do this right, we reset IBC - * as well. - */ -static void ipath_7220_xgxs_reset(struct ipath_devdata *dd) -{ - u64 val, prev_val; - - prev_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig); - val = prev_val | INFINIPATH_XGXS_RESET; - prev_val &= ~INFINIPATH_XGXS_RESET; /* be sure */ - ipath_write_kreg(dd, dd->ipath_kregs->kr_control, - dd->ipath_control & ~INFINIPATH_C_LINKENABLE); - ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val); - ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); - ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, prev_val); - ipath_write_kreg(dd, dd->ipath_kregs->kr_control, - dd->ipath_control); -} - - -/* Still needs cleanup, too much hardwired stuff */ -static void autoneg_send(struct ipath_devdata *dd, - u32 *hdr, u32 dcnt, u32 *data) -{ - int i; - u64 cnt; - u32 __iomem *piobuf; - u32 pnum; - - i = 0; - cnt = 7 + dcnt + 1; /* 7 dword header, dword data, icrc */ - while (!(piobuf = ipath_getpiobuf(dd, cnt, &pnum))) { - if (i++ > 15) { - ipath_dbg("Couldn't get pio buffer for send\n"); - return; - } - udelay(2); - } - if (dd->ipath_flags&IPATH_HAS_PBC_CNT) - cnt |= 0x80000000UL<<32; /* mark as VL15 */ - writeq(cnt, piobuf); - ipath_flush_wc(); - __iowrite32_copy(piobuf + 2, hdr, 7); - __iowrite32_copy(piobuf + 9, data, dcnt); - ipath_flush_wc(); -} - -/* - * _start packet gets sent twice at start, _done gets sent twice at end - */ -static void ipath_autoneg_send(struct ipath_devdata *dd, int which) -{ - static u32 swapped; - u32 dw, i, hcnt, dcnt, *data; - static u32 hdr[7] = { 0xf002ffff, 0x48ffff, 0x6400abba }; - static u32 madpayload_start[0x40] = { - 0x1810103, 0x1, 0x0, 0x0, 0x2c90000, 0x2c9, 0x0, 0x0, - 0xffffffff, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, - 0x1, 0x1388, 0x15e, 0x1, /* rest 0's */ - }; - static u32 madpayload_done[0x40] = { - 0x1810103, 0x1, 0x0, 0x0, 0x2c90000, 0x2c9, 0x0, 0x0, - 0xffffffff, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, - 0x40000001, 0x1388, 0x15e, /* rest 0's */ - }; - dcnt = ARRAY_SIZE(madpayload_start); - hcnt = ARRAY_SIZE(hdr); - if (!swapped) { - /* for maintainability, do it at runtime */ - for (i = 0; i < hcnt; i++) { - dw = (__force u32) cpu_to_be32(hdr[i]); - hdr[i] = dw; - } - for (i = 0; i < dcnt; i++) { - dw = (__force u32) cpu_to_be32(madpayload_start[i]); - madpayload_start[i] = dw; - dw = (__force u32) cpu_to_be32(madpayload_done[i]); - madpayload_done[i] = dw; - } - swapped = 1; - } - - data = which ? madpayload_done : madpayload_start; - ipath_cdbg(PKT, "Sending %s special MADs\n", which?"done":"start"); - - autoneg_send(dd, hdr, dcnt, data); - ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch); - udelay(2); - autoneg_send(dd, hdr, dcnt, data); - ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch); - udelay(2); -} - - - -/* - * Do the absolute minimum to cause an IB speed change, and make it - * ready, but don't actually trigger the change. The caller will - * do that when ready (if link is in Polling training state, it will - * happen immediately, otherwise when link next goes down) - * - * This routine should only be used as part of the DDR autonegotation - * code for devices that are not compliant with IB 1.2 (or code that - * fixes things up for same). - * - * When link has gone down, and autoneg enabled, or autoneg has - * failed and we give up until next time we set both speeds, and - * then we want IBTA enabled as well as "use max enabled speed. - */ -static void set_speed_fast(struct ipath_devdata *dd, u32 speed) -{ - dd->ipath_ibcddrctrl &= ~(IBA7220_IBC_SPEED_AUTONEG_MASK | - IBA7220_IBC_IBTA_1_2_MASK | - (IBA7220_IBC_WIDTH_MASK << IBA7220_IBC_WIDTH_SHIFT)); - - if (speed == (IPATH_IB_SDR | IPATH_IB_DDR)) - dd->ipath_ibcddrctrl |= IBA7220_IBC_SPEED_AUTONEG_MASK | - IBA7220_IBC_IBTA_1_2_MASK; - else - dd->ipath_ibcddrctrl |= speed == IPATH_IB_DDR ? - IBA7220_IBC_SPEED_DDR : IBA7220_IBC_SPEED_SDR; - - /* - * Convert from IB-style 1 = 1x, 2 = 4x, 3 = auto - * to chip-centric 0 = 1x, 1 = 4x, 2 = auto - */ - dd->ipath_ibcddrctrl |= (u64)(dd->ipath_link_width_enabled - 1) << - IBA7220_IBC_WIDTH_SHIFT; - ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcddrctrl, - dd->ipath_ibcddrctrl); - ipath_cdbg(VERBOSE, "setup for IB speed (%x) done\n", speed); -} - - -/* - * this routine is only used when we are not talking to another - * IB 1.2-compliant device that we think can do DDR. - * (This includes all existing switch chips as of Oct 2007.) - * 1.2-compliant devices go directly to DDR prior to reaching INIT - */ -static void try_auto_neg(struct ipath_devdata *dd) -{ - /* - * required for older non-IB1.2 DDR switches. Newer - * non-IB-compliant switches don't need it, but so far, - * aren't bothered by it either. "Magic constant" - */ - ipath_write_kreg(dd, IPATH_KREG_OFFSET(IBNCModeCtrl), - 0x3b9dc07); - dd->ipath_flags |= IPATH_IB_AUTONEG_INPROG; - ipath_autoneg_send(dd, 0); - set_speed_fast(dd, IPATH_IB_DDR); - ipath_toggle_rclkrls(dd); - /* 2 msec is minimum length of a poll cycle */ - schedule_delayed_work(&dd->ipath_autoneg_work, - msecs_to_jiffies(2)); -} - - -static int ipath_7220_ib_updown(struct ipath_devdata *dd, int ibup, u64 ibcs) -{ - int ret = 0, symadj = 0; - u32 ltstate = ipath_ib_linkstate(dd, ibcs); - - dd->ipath_link_width_active = - ((ibcs >> IBA7220_IBCS_LINKWIDTH_SHIFT) & 1) ? - IB_WIDTH_4X : IB_WIDTH_1X; - dd->ipath_link_speed_active = - ((ibcs >> IBA7220_IBCS_LINKSPEED_SHIFT) & 1) ? - IPATH_IB_DDR : IPATH_IB_SDR; - - if (!ibup) { - /* - * when link goes down we don't want aeq running, so it - * won't't interfere with IBC training, etc., and we need - * to go back to the static SerDes preset values - */ - if (dd->ipath_x1_fix_tries && - ltstate <= INFINIPATH_IBCS_LT_STATE_SLEEPQUIET && - ltstate != INFINIPATH_IBCS_LT_STATE_LINKUP) - dd->ipath_x1_fix_tries = 0; - if (!(dd->ipath_flags & (IPATH_IB_AUTONEG_FAILED | - IPATH_IB_AUTONEG_INPROG))) - set_speed_fast(dd, dd->ipath_link_speed_enabled); - if (!(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG)) { - ipath_cdbg(VERBOSE, "Setting RXEQ defaults\n"); - ipath_sd7220_presets(dd); - } - /* this might better in ipath_sd7220_presets() */ - ipath_set_relock_poll(dd, ibup); - } else { - if (ipath_compat_ddr_negotiate && - !(dd->ipath_flags & (IPATH_IB_AUTONEG_FAILED | - IPATH_IB_AUTONEG_INPROG)) && - dd->ipath_link_speed_active == IPATH_IB_SDR && - (dd->ipath_link_speed_enabled & - (IPATH_IB_DDR | IPATH_IB_SDR)) == - (IPATH_IB_DDR | IPATH_IB_SDR) && - dd->ipath_autoneg_tries < IPATH_AUTONEG_TRIES) { - /* we are SDR, and DDR auto-negotiation enabled */ - ++dd->ipath_autoneg_tries; - ipath_dbg("DDR negotiation try, %u/%u\n", - dd->ipath_autoneg_tries, - IPATH_AUTONEG_TRIES); - if (!dd->ibdeltainprog) { - dd->ibdeltainprog = 1; - dd->ibsymsnap = ipath_read_creg32(dd, - dd->ipath_cregs->cr_ibsymbolerrcnt); - dd->iblnkerrsnap = ipath_read_creg32(dd, - dd->ipath_cregs->cr_iblinkerrrecovcnt); - } - try_auto_neg(dd); - ret = 1; /* no other IB status change processing */ - } else if ((dd->ipath_flags & IPATH_IB_AUTONEG_INPROG) - && dd->ipath_link_speed_active == IPATH_IB_SDR) { - ipath_autoneg_send(dd, 1); - set_speed_fast(dd, IPATH_IB_DDR); - udelay(2); - ipath_toggle_rclkrls(dd); - ret = 1; /* no other IB status change processing */ - } else { - if ((dd->ipath_flags & IPATH_IB_AUTONEG_INPROG) && - (dd->ipath_link_speed_active & IPATH_IB_DDR)) { - ipath_dbg("Got to INIT with DDR autoneg\n"); - dd->ipath_flags &= ~(IPATH_IB_AUTONEG_INPROG - | IPATH_IB_AUTONEG_FAILED); - dd->ipath_autoneg_tries = 0; - /* re-enable SDR, for next link down */ - set_speed_fast(dd, - dd->ipath_link_speed_enabled); - wake_up(&dd->ipath_autoneg_wait); - symadj = 1; - } else if (dd->ipath_flags & IPATH_IB_AUTONEG_FAILED) { - /* - * clear autoneg failure flag, and do setup - * so we'll try next time link goes down and - * back to INIT (possibly connected to different - * device). - */ - ipath_dbg("INIT %sDR after autoneg failure\n", - (dd->ipath_link_speed_active & - IPATH_IB_DDR) ? "D" : "S"); - dd->ipath_flags &= ~IPATH_IB_AUTONEG_FAILED; - dd->ipath_ibcddrctrl |= - IBA7220_IBC_IBTA_1_2_MASK; - ipath_write_kreg(dd, - IPATH_KREG_OFFSET(IBNCModeCtrl), 0); - symadj = 1; - } - } - /* - * if we are in 1X on rev1 only, and are in autoneg width, - * it could be due to an xgxs problem, so if we haven't - * already tried, try twice to get to 4X; if we - * tried, and couldn't, report it, since it will - * probably not be what is desired. - */ - if (dd->ipath_minrev == 1 && - (dd->ipath_link_width_enabled & (IB_WIDTH_1X | - IB_WIDTH_4X)) == (IB_WIDTH_1X | IB_WIDTH_4X) - && dd->ipath_link_width_active == IB_WIDTH_1X - && dd->ipath_x1_fix_tries < 3) { - if (++dd->ipath_x1_fix_tries == 3) { - dev_info(&dd->pcidev->dev, - "IB link is in 1X mode\n"); - if (!(dd->ipath_flags & - IPATH_IB_AUTONEG_INPROG)) - symadj = 1; - } - else { - ipath_cdbg(VERBOSE, "IB 1X in " - "auto-width, try %u to be " - "sure it's really 1X; " - "ltstate %u\n", - dd->ipath_x1_fix_tries, - ltstate); - dd->ipath_f_xgxs_reset(dd); - ret = 1; /* skip other processing */ - } - } else if (!(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG)) - symadj = 1; - - if (!ret) { - dd->delay_mult = rate_to_delay - [(ibcs >> IBA7220_IBCS_LINKSPEED_SHIFT) & 1] - [(ibcs >> IBA7220_IBCS_LINKWIDTH_SHIFT) & 1]; - - ipath_set_relock_poll(dd, ibup); - } - } - - if (symadj) { - if (dd->ibdeltainprog) { - dd->ibdeltainprog = 0; - dd->ibsymdelta += ipath_read_creg32(dd, - dd->ipath_cregs->cr_ibsymbolerrcnt) - - dd->ibsymsnap; - dd->iblnkerrdelta += ipath_read_creg32(dd, - dd->ipath_cregs->cr_iblinkerrrecovcnt) - - dd->iblnkerrsnap; - } - } else if (!ibup && !dd->ibdeltainprog - && !(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG)) { - dd->ibdeltainprog = 1; - dd->ibsymsnap = ipath_read_creg32(dd, - dd->ipath_cregs->cr_ibsymbolerrcnt); - dd->iblnkerrsnap = ipath_read_creg32(dd, - dd->ipath_cregs->cr_iblinkerrrecovcnt); - } - - if (!ret) - ipath_setup_7220_setextled(dd, ipath_ib_linkstate(dd, ibcs), - ltstate); - return ret; -} - - -/* - * Handle the empirically determined mechanism for auto-negotiation - * of DDR speed with switches. - */ -static void autoneg_work(struct work_struct *work) -{ - struct ipath_devdata *dd; - u64 startms; - u32 lastlts, i; - - dd = container_of(work, struct ipath_devdata, - ipath_autoneg_work.work); - - startms = jiffies_to_msecs(jiffies); - - /* - * busy wait for this first part, it should be at most a - * few hundred usec, since we scheduled ourselves for 2msec. - */ - for (i = 0; i < 25; i++) { - lastlts = ipath_ib_linktrstate(dd, dd->ipath_lastibcstat); - if (lastlts == INFINIPATH_IBCS_LT_STATE_POLLQUIET) { - ipath_set_linkstate(dd, IPATH_IB_LINKDOWN_DISABLE); - break; - } - udelay(100); - } - - if (!(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG)) - goto done; /* we got there early or told to stop */ - - /* we expect this to timeout */ - if (wait_event_timeout(dd->ipath_autoneg_wait, - !(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG), - msecs_to_jiffies(90))) - goto done; - - ipath_toggle_rclkrls(dd); - - /* we expect this to timeout */ - if (wait_event_timeout(dd->ipath_autoneg_wait, - !(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG), - msecs_to_jiffies(1700))) - goto done; - - set_speed_fast(dd, IPATH_IB_SDR); - ipath_toggle_rclkrls(dd); - - /* - * wait up to 250 msec for link to train and get to INIT at DDR; - * this should terminate early - */ - wait_event_timeout(dd->ipath_autoneg_wait, - !(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG), - msecs_to_jiffies(250)); -done: - if (dd->ipath_flags & IPATH_IB_AUTONEG_INPROG) { - ipath_dbg("Did not get to DDR INIT (%x) after %Lu msecs\n", - ipath_ib_state(dd, dd->ipath_lastibcstat), - (unsigned long long) jiffies_to_msecs(jiffies)-startms); - dd->ipath_flags &= ~IPATH_IB_AUTONEG_INPROG; - if (dd->ipath_autoneg_tries == IPATH_AUTONEG_TRIES) { - dd->ipath_flags |= IPATH_IB_AUTONEG_FAILED; - ipath_dbg("Giving up on DDR until next IB " - "link Down\n"); - dd->ipath_autoneg_tries = 0; - } - set_speed_fast(dd, dd->ipath_link_speed_enabled); - } -} - - -/** - * ipath_init_iba7220_funcs - set up the chip-specific function pointers - * @dd: the infinipath device - * - * This is global, and is called directly at init to set up the - * chip-specific function pointers for later use. - */ -void ipath_init_iba7220_funcs(struct ipath_devdata *dd) -{ - dd->ipath_f_intrsetup = ipath_7220_intconfig; - dd->ipath_f_bus = ipath_setup_7220_config; - dd->ipath_f_reset = ipath_setup_7220_reset; - dd->ipath_f_get_boardname = ipath_7220_boardname; - dd->ipath_f_init_hwerrors = ipath_7220_init_hwerrors; - dd->ipath_f_early_init = ipath_7220_early_init; - dd->ipath_f_handle_hwerrors = ipath_7220_handle_hwerrors; - dd->ipath_f_quiet_serdes = ipath_7220_quiet_serdes; - dd->ipath_f_bringup_serdes = ipath_7220_bringup_serdes; - dd->ipath_f_clear_tids = ipath_7220_clear_tids; - dd->ipath_f_put_tid = ipath_7220_put_tid; - dd->ipath_f_cleanup = ipath_setup_7220_cleanup; - dd->ipath_f_setextled = ipath_setup_7220_setextled; - dd->ipath_f_get_base_info = ipath_7220_get_base_info; - dd->ipath_f_free_irq = ipath_7220_free_irq; - dd->ipath_f_tidtemplate = ipath_7220_tidtemplate; - dd->ipath_f_intr_fallback = ipath_7220_intr_fallback; - dd->ipath_f_xgxs_reset = ipath_7220_xgxs_reset; - dd->ipath_f_get_ib_cfg = ipath_7220_get_ib_cfg; - dd->ipath_f_set_ib_cfg = ipath_7220_set_ib_cfg; - dd->ipath_f_config_jint = ipath_7220_config_jint; - dd->ipath_f_config_ports = ipath_7220_config_ports; - dd->ipath_f_read_counters = ipath_7220_read_counters; - dd->ipath_f_get_msgheader = ipath_7220_get_msgheader; - dd->ipath_f_ib_updown = ipath_7220_ib_updown; - - /* initialize chip-specific variables */ - ipath_init_7220_variables(dd); -} |
