diff options
Diffstat (limited to 'drivers/ide/Kconfig')
| -rw-r--r-- | drivers/ide/Kconfig | 54 |
1 files changed, 11 insertions, 43 deletions
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index f702f91..b4f3aef 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -1,8 +1,6 @@ # # IDE ATA ATAPI Block device driver configuration # -# Andre Hedrick <andre@linux-ide.org> -# # Select HAVE_IDE if IDE is supported config HAVE_IDE @@ -335,7 +333,7 @@ config BLK_DEV_CMD640 This driver will work automatically in PCI based systems (most new systems have PCI slots). But if your system uses VESA local bus (VLB) instead of PCI, you must also supply a kernel boot parameter - to enable the CMD640 bugfix/support: "ide0=cmd640_vlb". (Try "man + to enable the CMD640 bugfix/support: "cmd640.probe_vlb". (Try "man bootparam" or see the documentation of your boot loader about how to pass options to the kernel.) @@ -457,27 +455,11 @@ config BLK_DEV_ALI15X3 onboard chipsets. It also tests for Simplex mode and enables normal dual channel support. - If you say Y here, you also need to say Y to "Use DMA by default - when available", above. Please read the comments at the top of + Please read the comments at the top of <file:drivers/ide/pci/alim15x3.c>. If unsure, say N. -config WDC_ALI15X3 - bool "ALI M15x3 WDC support (DANGEROUS)" - depends on BLK_DEV_ALI15X3 - ---help--- - This allows for UltraDMA support for WDC drives that ignore CRC - checking. You are a fool for enabling this option, but there have - been requests. DO NOT COMPLAIN IF YOUR DRIVE HAS FS CORRUPTION, IF - YOU ENABLE THIS! No one will listen, just laugh for ignoring this - SERIOUS WARNING. - - Using this option can allow WDC drives to run at ATA-4/5 transfer - rates with only an ATA-2 support structure. - - SAY N! - config BLK_DEV_AMD74XX tristate "AMD and nVidia IDE support" depends on !ARM @@ -520,9 +502,6 @@ config BLK_DEV_CY82C693 This driver adds detection and support for the CY82C693 chipset used on Digital's PC-Alpha 164SX boards. - If you say Y here, you need to say Y to "Use DMA by default - when available" as well. - config BLK_DEV_CS5520 tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)" depends on EXPERIMENTAL @@ -613,13 +592,12 @@ config BLK_DEV_SC1200 National SCx200 series of embedded x86 "Geode" systems. config BLK_DEV_PIIX - tristate "Intel PIIXn chipsets support" + tristate "Intel PIIX/ICH chipsets support" select BLK_DEV_IDEDMA_PCI help - This driver adds explicit support for Intel PIIX and ICH chips - and also for the Efar Victory66 (slc90e66) chip. This allows - the kernel to change PIO, DMA and UDMA speeds and to configure - the chip to optimum performance. + This driver adds explicit support for Intel PIIX and ICH chips. + This allows the kernel to change PIO, DMA and UDMA speeds and to + configure the chip to optimum performance. config BLK_DEV_IT8213 tristate "IT8213 IDE support" @@ -657,11 +635,7 @@ config BLK_DEV_PDC202XX_OLD happen if the BIOS revisions of all installed cards (three-max) do not match, the driver attempts to do dynamic tuning of the chipset at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required - for more than one card. This card may require that you say Y to - "Special UDMA Feature". - - If you say Y here, you need to say Y to "Use DMA by default when - available" as well. + for more than one card. Please read the comments at the top of <file:drivers/ide/pci/pdc202xx_old.c>. @@ -710,9 +684,6 @@ config BLK_DEV_SIS5513 ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740, SiS745, SiS750 - If you say Y here, you need to say Y to "Use DMA by default when - available" as well. - Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>. config BLK_DEV_SL82C105 @@ -734,9 +705,6 @@ config BLK_DEV_SLC90E66 and it will handle timing cycles. Since this is an improved look-a-like to the PIIX4 it should be a nice addition. - If you say Y here, you need to say Y to "Use DMA by default when - available" as well. - Please read the comments at the top of <file:drivers/ide/pci/slc90e66.c>. @@ -888,17 +856,17 @@ config BLK_DEV_IDEDOUBLER bool "Amiga IDE Doubler support (EXPERIMENTAL)" depends on BLK_DEV_GAYLE && EXPERIMENTAL ---help--- - This driver provides support for the so-called `IDE doublers' (made + This feature provides support for the so-called `IDE doublers' (made by various manufacturers, e.g. Eyetech) that can be connected to the on-board IDE interface of some Amiga models. Using such an IDE doubler, you can connect up to four instead of two IDE devices to the Amiga's on-board IDE interface. Note that the normal Amiga Gayle IDE driver may not work correctly - if you have an IDE doubler and don't enable this driver! + if you have an IDE doubler and don't enable this feature! - Say Y if you have an IDE doubler. The driver is enabled at kernel - runtime using the "ide=doubler" kernel boot parameter. + Say Y if you have an IDE doubler. The feature is enabled at kernel + runtime using the "gayle.doubler" kernel boot parameter. config BLK_DEV_BUDDHA tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)" |
