summaryrefslogtreecommitdiffstats
path: root/drivers/i2c/chips/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/i2c/chips/Kconfig')
-rw-r--r--drivers/i2c/chips/Kconfig43
1 files changed, 38 insertions, 5 deletions
diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig
index 2da2edf..50e0a46 100644
--- a/drivers/i2c/chips/Kconfig
+++ b/drivers/i2c/chips/Kconfig
@@ -14,6 +14,32 @@ config DS1682
This driver can also be built as a module. If so, the module
will be called ds1682.
+config AT24
+ tristate "EEPROMs from most vendors"
+ depends on SYSFS && EXPERIMENTAL
+ help
+ Enable this driver to get read/write support to most I2C EEPROMs,
+ after you configure the driver to know about each EEPROM on
+ your target board. Use these generic chip names, instead of
+ vendor-specific ones like at24c64 or 24lc02:
+
+ 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
+ 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
+
+ Unless you like data loss puzzles, always be sure that any chip
+ you configure as a 24c32 (32 kbit) or larger is NOT really a
+ 24c16 (16 kbit) or smaller, and vice versa. Marking the chip
+ as read-only won't help recover from this. Also, if your chip
+ has any software write-protect mechanism you may want to review the
+ code to make sure this driver won't turn it on by accident.
+
+ If you use this with an SMBus adapter instead of an I2C adapter,
+ full functionality is not available. Only smaller devices are
+ supported (24c16 and below, max 4 kByte).
+
+ This driver can also be built as a module. If so, the module
+ will be called at24.
+
config SENSORS_EEPROM
tristate "EEPROM reader"
depends on EXPERIMENTAL
@@ -26,8 +52,8 @@ config SENSORS_EEPROM
will be called eeprom.
config SENSORS_PCF8574
- tristate "Philips PCF8574 and PCF8574A"
- depends on EXPERIMENTAL
+ tristate "Philips PCF8574 and PCF8574A (DEPRECATED)"
+ depends on EXPERIMENTAL && GPIO_PCF857X = "n"
default n
help
If you say yes here you get support for Philips PCF8574 and
@@ -36,12 +62,16 @@ config SENSORS_PCF8574
This driver can also be built as a module. If so, the module
will be called pcf8574.
+ This driver is deprecated and will be dropped soon. Use
+ drivers/gpio/pcf857x.c instead.
+
These devices are hard to detect and rarely found on mainstream
hardware. If unsure, say N.
config PCF8575
- tristate "Philips PCF8575"
+ tristate "Philips PCF8575 (DEPRECATED)"
default n
+ depends on GPIO_PCF857X = "n"
help
If you say yes here you get support for Philips PCF8575 chip.
This chip is a 16-bit I/O expander for the I2C bus. Several other
@@ -50,12 +80,15 @@ config PCF8575
This driver can also be built as a module. If so, the module
will be called pcf8575.
+ This driver is deprecated and will be dropped soon. Use
+ drivers/gpio/pcf857x.c instead.
+
This device is hard to detect and is rarely found on mainstream
hardware. If unsure, say N.
config SENSORS_PCA9539
tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)"
- depends on EXPERIMENTAL && GPIO_PCA9539 = "n"
+ depends on EXPERIMENTAL && GPIO_PCA953X = "n"
help
If you say yes here you get support for the Philips PCA9539
16-bit I/O port.
@@ -64,7 +97,7 @@ config SENSORS_PCA9539
will be called pca9539.
This driver is deprecated and will be dropped soon. Use
- drivers/gpio/pca9539.c instead.
+ drivers/gpio/pca953x.c instead.
config SENSORS_PCF8591
tristate "Philips PCF8591"
OpenPOWER on IntegriCloud