diff options
Diffstat (limited to 'drivers/hwmon/lm90.c')
-rw-r--r-- | drivers/hwmon/lm90.c | 24 |
1 files changed, 16 insertions, 8 deletions
diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index 812781c..2f94f95 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -49,10 +49,10 @@ * chips, but support three temperature sensors instead of two. MAX6695 * and MAX6696 only differ in the pinout so they can be treated identically. * - * This driver also supports the ADT7461 chip from Analog Devices. - * It's supported in both compatibility and extended mode. It is mostly - * compatible with LM90 except for a data format difference for the - * temperature value registers. + * This driver also supports ADT7461 and ADT7461A from Analog Devices as well as + * NCT1008 from ON Semiconductor. The chips are supported in both compatibility + * and extended mode. They are mostly compatible with LM90 except for a data + * format difference for the temperature value registers. * * Since the LM90 was the first chipset supported by this driver, most * comments will refer to this chipset, but are actually general and @@ -88,9 +88,10 @@ * Addresses to scan * Address is fully defined internally and cannot be changed except for * MAX6659, MAX6680 and MAX6681. - * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, MAX6649, MAX6657, - * MAX6658 and W83L771 have address 0x4c. - * ADM1032-2, ADT7461-2, LM89-1, LM99-1 and MAX6646 have address 0x4d. + * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, ADT7461A, MAX6649, + * MAX6657, MAX6658, NCT1008 and W83L771 have address 0x4c. + * ADM1032-2, ADT7461-2, ADT7461A-2, LM89-1, LM99-1, MAX6646, and NCT1008D + * have address 0x4d. * MAX6647 has address 0x4e. * MAX6659 can have address 0x4c, 0x4d or 0x4e. * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, @@ -174,6 +175,7 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680, static const struct i2c_device_id lm90_id[] = { { "adm1032", adm1032 }, { "adt7461", adt7461 }, + { "adt7461a", adt7461 }, { "lm90", lm90 }, { "lm86", lm86 }, { "lm89", lm86 }, @@ -188,6 +190,7 @@ static const struct i2c_device_id lm90_id[] = { { "max6681", max6680 }, { "max6695", max6696 }, { "max6696", max6696 }, + { "nct1008", adt7461 }, { "w83l771", w83l771 }, { } }; @@ -356,7 +359,7 @@ static int lm90_read16(struct i2c_client *client, u8 regh, u8 regl, u16 *value) /* * There is a trick here. We have to read two registers to have the * sensor temperature, but we have to beware a conversion could occur - * inbetween the readings. The datasheet says we should either use + * between the readings. The datasheet says we should either use * the one-shot conversion register, which we don't want to do * (disables hardware monitoring) or monitor the busy bit, which is * impossible (we can't read the values and monitor that bit at the @@ -1153,6 +1156,11 @@ static int lm90_detect(struct i2c_client *new_client, && (reg_config1 & 0x1B) == 0x00 && reg_convrate <= 0x0A) { name = "adt7461"; + } else + if (chip_id == 0x57 /* ADT7461A, NCT1008 */ + && (reg_config1 & 0x1B) == 0x00 + && reg_convrate <= 0x0A) { + name = "adt7461a"; } } else if (man_id == 0x4D) { /* Maxim */ |