diff options
Diffstat (limited to 'drivers/gpu/drm/i915/intel_dp.c')
-rw-r--r-- | drivers/gpu/drm/i915/intel_dp.c | 366 |
1 files changed, 251 insertions, 115 deletions
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c index 0b8e8eb..d1670b8 100644 --- a/drivers/gpu/drm/i915/intel_dp.c +++ b/drivers/gpu/drm/i915/intel_dp.c @@ -156,38 +156,28 @@ static u8 intel_dp_max_lane_count(struct intel_dp *intel_dp) u8 source_max, sink_max; source_max = intel_dig_port->max_lanes; - sink_max = drm_dp_max_lane_count(intel_dp->dpcd); + sink_max = intel_dp->max_sink_lane_count; return min(source_max, sink_max); } -/* - * The units on the numbers in the next two are... bizarre. Examples will - * make it clearer; this one parallels an example in the eDP spec. - * - * intel_dp_max_data_rate for one lane of 2.7GHz evaluates as: - * - * 270000 * 1 * 8 / 10 == 216000 - * - * The actual data capacity of that configuration is 2.16Gbit/s, so the - * units are decakilobits. ->clock in a drm_display_mode is in kilohertz - - * or equivalently, kilopixels per second - so for 1680x1050R it'd be - * 119000. At 18bpp that's 2142000 kilobits per second. - * - * Thus the strange-looking division by 10 in intel_dp_link_required, to - * get the result in decakilobits instead of kilobits. - */ - -static int +int intel_dp_link_required(int pixel_clock, int bpp) { - return (pixel_clock * bpp + 9) / 10; + /* pixel_clock is in kHz, divide bpp by 8 for bit to Byte conversion */ + return DIV_ROUND_UP(pixel_clock * bpp, 8); } -static int +int intel_dp_max_data_rate(int max_link_clock, int max_lanes) { - return (max_link_clock * max_lanes * 8) / 10; + /* max_link_clock is the link symbol clock (LS_Clk) in kHz and not the + * link rate that is generally expressed in Gbps. Since, 8 bits of data + * is transmitted every LS_Clk per lane, there is no need to account for + * the channel encoding that is done in the PHY layer here. + */ + + return max_link_clock * max_lanes; } static int @@ -223,7 +213,7 @@ intel_dp_sink_rates(struct intel_dp *intel_dp, const int **sink_rates) *sink_rates = default_rates; - return (intel_dp_max_link_bw(intel_dp) >> 3) + 1; + return (intel_dp->max_sink_link_bw >> 3) + 1; } static int @@ -233,7 +223,7 @@ intel_dp_source_rates(struct intel_dp *intel_dp, const int **source_rates) struct drm_i915_private *dev_priv = to_i915(dig_port->base.base.dev); int size; - if (IS_BROXTON(dev_priv)) { + if (IS_GEN9_LP(dev_priv)) { *source_rates = bxt_rates; size = ARRAY_SIZE(bxt_rates); } else if (IS_SKYLAKE(dev_priv) || IS_KABYLAKE(dev_priv)) { @@ -288,6 +278,44 @@ static int intel_dp_common_rates(struct intel_dp *intel_dp, common_rates); } +static int intel_dp_link_rate_index(struct intel_dp *intel_dp, + int *common_rates, int link_rate) +{ + int common_len; + int index; + + common_len = intel_dp_common_rates(intel_dp, common_rates); + for (index = 0; index < common_len; index++) { + if (link_rate == common_rates[common_len - index - 1]) + return common_len - index - 1; + } + + return -1; +} + +int intel_dp_get_link_train_fallback_values(struct intel_dp *intel_dp, + int link_rate, uint8_t lane_count) +{ + int common_rates[DP_MAX_SUPPORTED_RATES]; + int link_rate_index; + + link_rate_index = intel_dp_link_rate_index(intel_dp, + common_rates, + link_rate); + if (link_rate_index > 0) { + intel_dp->max_sink_link_bw = drm_dp_link_rate_to_bw_code(common_rates[link_rate_index - 1]); + intel_dp->max_sink_lane_count = lane_count; + } else if (lane_count > 1) { + intel_dp->max_sink_link_bw = intel_dp_max_link_bw(intel_dp); + intel_dp->max_sink_lane_count = lane_count >> 1; + } else { + DRM_ERROR("Link Training Unsuccessful\n"); + return -1; + } + + return 0; +} + static enum drm_mode_status intel_dp_mode_valid(struct drm_connector *connector, struct drm_display_mode *mode) @@ -465,14 +493,50 @@ vlv_power_sequencer_kick(struct intel_dp *intel_dp) } } +static enum pipe vlv_find_free_pps(struct drm_i915_private *dev_priv) +{ + struct intel_encoder *encoder; + unsigned int pipes = (1 << PIPE_A) | (1 << PIPE_B); + + /* + * We don't have power sequencer currently. + * Pick one that's not used by other ports. + */ + for_each_intel_encoder(&dev_priv->drm, encoder) { + struct intel_dp *intel_dp; + + if (encoder->type != INTEL_OUTPUT_DP && + encoder->type != INTEL_OUTPUT_EDP) + continue; + + intel_dp = enc_to_intel_dp(&encoder->base); + + if (encoder->type == INTEL_OUTPUT_EDP) { + WARN_ON(intel_dp->active_pipe != INVALID_PIPE && + intel_dp->active_pipe != intel_dp->pps_pipe); + + if (intel_dp->pps_pipe != INVALID_PIPE) + pipes &= ~(1 << intel_dp->pps_pipe); + } else { + WARN_ON(intel_dp->pps_pipe != INVALID_PIPE); + + if (intel_dp->active_pipe != INVALID_PIPE) + pipes &= ~(1 << intel_dp->active_pipe); + } + } + + if (pipes == 0) + return INVALID_PIPE; + + return ffs(pipes) - 1; +} + static enum pipe vlv_power_sequencer_pipe(struct intel_dp *intel_dp) { struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp); struct drm_device *dev = intel_dig_port->base.base.dev; struct drm_i915_private *dev_priv = to_i915(dev); - struct intel_encoder *encoder; - unsigned int pipes = (1 << PIPE_A) | (1 << PIPE_B); enum pipe pipe; lockdep_assert_held(&dev_priv->pps_mutex); @@ -480,33 +544,20 @@ vlv_power_sequencer_pipe(struct intel_dp *intel_dp) /* We should never land here with regular DP ports */ WARN_ON(!is_edp(intel_dp)); + WARN_ON(intel_dp->active_pipe != INVALID_PIPE && + intel_dp->active_pipe != intel_dp->pps_pipe); + if (intel_dp->pps_pipe != INVALID_PIPE) return intel_dp->pps_pipe; - /* - * We don't have power sequencer currently. - * Pick one that's not used by other ports. - */ - for_each_intel_encoder(dev, encoder) { - struct intel_dp *tmp; - - if (encoder->type != INTEL_OUTPUT_EDP) - continue; - - tmp = enc_to_intel_dp(&encoder->base); - - if (tmp->pps_pipe != INVALID_PIPE) - pipes &= ~(1 << tmp->pps_pipe); - } + pipe = vlv_find_free_pps(dev_priv); /* * Didn't find one. This should not happen since there * are two power sequencers and up to two eDP ports. */ - if (WARN_ON(pipes == 0)) + if (WARN_ON(pipe == INVALID_PIPE)) pipe = PIPE_A; - else - pipe = ffs(pipes) - 1; vlv_steal_power_sequencer(dev, pipe); intel_dp->pps_pipe = pipe; @@ -646,7 +697,7 @@ void intel_power_sequencer_reset(struct drm_i915_private *dev_priv) struct intel_encoder *encoder; if (WARN_ON(!IS_VALLEYVIEW(dev_priv) && !IS_CHERRYVIEW(dev_priv) && - !IS_BROXTON(dev_priv))) + !IS_GEN9_LP(dev_priv))) return; /* @@ -662,11 +713,18 @@ void intel_power_sequencer_reset(struct drm_i915_private *dev_priv) for_each_intel_encoder(dev, encoder) { struct intel_dp *intel_dp; - if (encoder->type != INTEL_OUTPUT_EDP) + if (encoder->type != INTEL_OUTPUT_DP && + encoder->type != INTEL_OUTPUT_EDP) continue; intel_dp = enc_to_intel_dp(&encoder->base); - if (IS_BROXTON(dev_priv)) + + WARN_ON(intel_dp->active_pipe != INVALID_PIPE); + + if (encoder->type != INTEL_OUTPUT_EDP) + continue; + + if (IS_GEN9_LP(dev_priv)) intel_dp->pps_reset = true; else intel_dp->pps_pipe = INVALID_PIPE; @@ -689,7 +747,7 @@ static void intel_pps_get_registers(struct drm_i915_private *dev_priv, memset(regs, 0, sizeof(*regs)); - if (IS_BROXTON(dev_priv)) + if (IS_GEN9_LP(dev_priv)) pps_idx = bxt_power_sequencer_idx(intel_dp); else if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) pps_idx = vlv_power_sequencer_pipe(intel_dp); @@ -698,7 +756,7 @@ static void intel_pps_get_registers(struct drm_i915_private *dev_priv, regs->pp_stat = PP_STATUS(pps_idx); regs->pp_on = PP_ON_DELAYS(pps_idx); regs->pp_off = PP_OFF_DELAYS(pps_idx); - if (!IS_BROXTON(dev_priv)) + if (!IS_GEN9_LP(dev_priv)) regs->pp_div = PP_DIVISOR(pps_idx); } @@ -1655,7 +1713,9 @@ found: * VESA DisplayPort Ver.1.2a - 5.1.1.1 Video Colorimetry */ pipe_config->limited_color_range = - bpp != 18 && drm_match_cea_mode(adjusted_mode) > 1; + bpp != 18 && + drm_default_rgb_quant_range(adjusted_mode) == + HDMI_QUANTIZATION_RANGE_LIMITED; } else { pipe_config->limited_color_range = intel_dp->limited_color_range; @@ -2402,6 +2462,8 @@ void intel_dp_sink_dpms(struct intel_dp *intel_dp, int mode) ret = drm_dp_dpcd_writeb(&intel_dp->aux, DP_SET_POWER, DP_SET_POWER_D3); } else { + struct intel_lspcon *lspcon = dp_to_lspcon(intel_dp); + /* * When turning on, we need to retry for 1ms to give the sink * time to wake up. @@ -2413,6 +2475,9 @@ void intel_dp_sink_dpms(struct intel_dp *intel_dp, int mode) break; msleep(1); } + + if (ret == 1 && lspcon->active) + lspcon_wait_pcon_mode(lspcon); } if (ret != 1) @@ -2820,6 +2885,11 @@ static void vlv_detach_power_sequencer(struct intel_dp *intel_dp) enum pipe pipe = intel_dp->pps_pipe; i915_reg_t pp_on_reg = PP_ON_DELAYS(pipe); + WARN_ON(intel_dp->active_pipe != INVALID_PIPE); + + if (WARN_ON(pipe != PIPE_A && pipe != PIPE_B)) + return; + edp_panel_vdd_off_sync(intel_dp); /* @@ -2847,29 +2917,27 @@ static void vlv_steal_power_sequencer(struct drm_device *dev, lockdep_assert_held(&dev_priv->pps_mutex); - if (WARN_ON(pipe != PIPE_A && pipe != PIPE_B)) - return; - for_each_intel_encoder(dev, encoder) { struct intel_dp *intel_dp; enum port port; - if (encoder->type != INTEL_OUTPUT_EDP) + if (encoder->type != INTEL_OUTPUT_DP && + encoder->type != INTEL_OUTPUT_EDP) continue; intel_dp = enc_to_intel_dp(&encoder->base); port = dp_to_dig_port(intel_dp)->port; + WARN(intel_dp->active_pipe == pipe, + "stealing pipe %c power sequencer from active (e)DP port %c\n", + pipe_name(pipe), port_name(port)); + if (intel_dp->pps_pipe != pipe) continue; DRM_DEBUG_KMS("stealing pipe %c power sequencer from port %c\n", pipe_name(pipe), port_name(port)); - WARN(encoder->base.crtc, - "stealing pipe %c power sequencer from active eDP port %c\n", - pipe_name(pipe), port_name(port)); - /* make sure vdd is off before we steal it */ vlv_detach_power_sequencer(intel_dp); } @@ -2885,19 +2953,17 @@ static void vlv_init_panel_power_sequencer(struct intel_dp *intel_dp) lockdep_assert_held(&dev_priv->pps_mutex); - if (!is_edp(intel_dp)) - return; + WARN_ON(intel_dp->active_pipe != INVALID_PIPE); - if (intel_dp->pps_pipe == crtc->pipe) - return; - - /* - * If another power sequencer was being used on this - * port previously make sure to turn off vdd there while - * we still have control of it. - */ - if (intel_dp->pps_pipe != INVALID_PIPE) + if (intel_dp->pps_pipe != INVALID_PIPE && + intel_dp->pps_pipe != crtc->pipe) { + /* + * If another power sequencer was being used on this + * port previously make sure to turn off vdd there while + * we still have control of it. + */ vlv_detach_power_sequencer(intel_dp); + } /* * We may be stealing the power @@ -2905,6 +2971,11 @@ static void vlv_init_panel_power_sequencer(struct intel_dp *intel_dp) */ vlv_steal_power_sequencer(dev, crtc->pipe); + intel_dp->active_pipe = crtc->pipe; + + if (!is_edp(intel_dp)) + return; + /* now it's all ours */ intel_dp->pps_pipe = crtc->pipe; @@ -2973,6 +3044,32 @@ intel_dp_get_link_status(struct intel_dp *intel_dp, uint8_t link_status[DP_LINK_ DP_LINK_STATUS_SIZE) == DP_LINK_STATUS_SIZE; } +static bool intel_dp_get_y_cord_status(struct intel_dp *intel_dp) +{ + uint8_t psr_caps = 0; + + drm_dp_dpcd_readb(&intel_dp->aux, DP_PSR_CAPS, &psr_caps); + return psr_caps & DP_PSR2_SU_Y_COORDINATE_REQUIRED; +} + +static bool intel_dp_get_colorimetry_status(struct intel_dp *intel_dp) +{ + uint8_t dprx = 0; + + drm_dp_dpcd_readb(&intel_dp->aux, + DP_DPRX_FEATURE_ENUMERATION_LIST, + &dprx); + return dprx & DP_VSC_SDP_EXT_FOR_COLORIMETRY_SUPPORTED; +} + +static bool intel_dp_get_alpm_status(struct intel_dp *intel_dp) +{ + uint8_t alpm_caps = 0; + + drm_dp_dpcd_readb(&intel_dp->aux, DP_RECEIVER_ALPM_CAP, &alpm_caps); + return alpm_caps & DP_ALPM_CAP; +} + /* These are source-specific values. */ uint8_t intel_dp_voltage_max(struct intel_dp *intel_dp) @@ -2980,7 +3077,7 @@ intel_dp_voltage_max(struct intel_dp *intel_dp) struct drm_i915_private *dev_priv = to_i915(intel_dp_to_dev(intel_dp)); enum port port = dp_to_dig_port(intel_dp)->port; - if (IS_BROXTON(dev_priv)) + if (IS_GEN9_LP(dev_priv)) return DP_TRAIN_VOLTAGE_SWING_LEVEL_3; else if (INTEL_GEN(dev_priv) >= 9) { if (dev_priv->vbt.edp.low_vswing && port == PORT_A) @@ -3343,7 +3440,7 @@ intel_dp_set_signal_levels(struct intel_dp *intel_dp) if (HAS_DDI(dev_priv)) { signal_levels = ddi_signal_levels(intel_dp); - if (IS_BROXTON(dev_priv)) + if (IS_GEN9_LP(dev_priv)) signal_levels = 0; else mask = DDI_BUF_EMP_MASK; @@ -3491,6 +3588,12 @@ intel_dp_link_down(struct intel_dp *intel_dp) msleep(intel_dp->panel_power_down_delay); intel_dp->DP = DP; + + if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) { + pps_lock(intel_dp); + intel_dp->active_pipe = INVALID_PIPE; + pps_unlock(intel_dp); + } } bool @@ -3545,6 +3648,16 @@ intel_edp_init_dpcd(struct intel_dp *intel_dp) dev_priv->psr.psr2_support = dev_priv->psr.aux_frame_sync; DRM_DEBUG_KMS("PSR2 %s on sink", dev_priv->psr.psr2_support ? "supported" : "not supported"); + + if (dev_priv->psr.psr2_support) { + dev_priv->psr.y_cord_support = + intel_dp_get_y_cord_status(intel_dp); + dev_priv->psr.colorimetry_support = + intel_dp_get_colorimetry_status(intel_dp); + dev_priv->psr.alpm = + intel_dp_get_alpm_status(intel_dp); + } + } /* Read the eDP Display control capabilities registers */ @@ -3569,7 +3682,12 @@ intel_edp_init_dpcd(struct intel_dp *intel_dp) if (val == 0) break; - /* Value read is in kHz while drm clock is saved in deca-kHz */ + /* Value read multiplied by 200kHz gives the per-lane + * link rate in kHz. The source rates are, however, + * stored in terms of LS_Clk kHz. The full conversion + * back to symbols is + * (val * 200kHz)*(8/10 ch. encoding)*(1/8 bit to Byte) + */ intel_dp->sink_rates[i] = (val * 200) / 10; } intel_dp->num_sink_rates = i; @@ -3835,7 +3953,7 @@ static uint8_t intel_dp_autotest_edid(struct intel_dp *intel_dp) DRM_DEBUG_KMS("EDID read had %d NACKs, %d DEFERs\n", intel_dp->aux.i2c_nack_count, intel_dp->aux.i2c_defer_count); - intel_dp->compliance_test_data = INTEL_DP_RESOLUTION_FAILSAFE; + intel_dp->compliance.test_data.edid = INTEL_DP_RESOLUTION_FAILSAFE; } else { struct edid *block = intel_connector->detect_edid; @@ -3851,11 +3969,11 @@ static uint8_t intel_dp_autotest_edid(struct intel_dp *intel_dp) DRM_DEBUG_KMS("Failed to write EDID checksum\n"); test_result = DP_TEST_ACK | DP_TEST_EDID_CHECKSUM_WRITE; - intel_dp->compliance_test_data = INTEL_DP_RESOLUTION_STANDARD; + intel_dp->compliance.test_data.edid = INTEL_DP_RESOLUTION_STANDARD; } /* Set test active flag here so userspace doesn't interrupt things */ - intel_dp->compliance_test_active = 1; + intel_dp->compliance.test_active = 1; return test_result; } @@ -3881,22 +3999,22 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp) switch (rxdata) { case DP_TEST_LINK_TRAINING: DRM_DEBUG_KMS("LINK_TRAINING test requested\n"); - intel_dp->compliance_test_type = DP_TEST_LINK_TRAINING; + intel_dp->compliance.test_type = DP_TEST_LINK_TRAINING; response = intel_dp_autotest_link_training(intel_dp); break; case DP_TEST_LINK_VIDEO_PATTERN: DRM_DEBUG_KMS("TEST_PATTERN test requested\n"); - intel_dp->compliance_test_type = DP_TEST_LINK_VIDEO_PATTERN; + intel_dp->compliance.test_type = DP_TEST_LINK_VIDEO_PATTERN; response = intel_dp_autotest_video_pattern(intel_dp); break; case DP_TEST_LINK_EDID_READ: DRM_DEBUG_KMS("EDID test requested\n"); - intel_dp->compliance_test_type = DP_TEST_LINK_EDID_READ; + intel_dp->compliance.test_type = DP_TEST_LINK_EDID_READ; response = intel_dp_autotest_edid(intel_dp); break; case DP_TEST_LINK_PHY_TEST_PATTERN: DRM_DEBUG_KMS("PHY_PATTERN test requested\n"); - intel_dp->compliance_test_type = DP_TEST_LINK_PHY_TEST_PATTERN; + intel_dp->compliance.test_type = DP_TEST_LINK_PHY_TEST_PATTERN; response = intel_dp_autotest_phy_pattern(intel_dp); break; default: @@ -4020,7 +4138,7 @@ intel_dp_check_link_status(struct intel_dp *intel_dp) return; /* if link training is requested we should perform it always */ - if ((intel_dp->compliance_test_type == DP_TEST_LINK_TRAINING) || + if ((intel_dp->compliance.test_type == DP_TEST_LINK_TRAINING) || (!drm_dp_channel_eq_ok(link_status, intel_dp->lane_count))) { DRM_DEBUG_KMS("%s: channel EQ not ok, retraining\n", intel_encoder->base.name); @@ -4054,9 +4172,7 @@ intel_dp_short_pulse(struct intel_dp *intel_dp) * Clearing compliance test variables to allow capturing * of values for next automated test request. */ - intel_dp->compliance_test_active = 0; - intel_dp->compliance_test_type = 0; - intel_dp->compliance_test_data = 0; + memset(&intel_dp->compliance, 0, sizeof(intel_dp->compliance)); /* * Now read the DPCD to see if it's actually running @@ -4148,9 +4264,10 @@ static enum drm_connector_status edp_detect(struct intel_dp *intel_dp) { struct drm_device *dev = intel_dp_to_dev(intel_dp); + struct drm_i915_private *dev_priv = to_i915(dev); enum drm_connector_status status; - status = intel_panel_detect(dev); + status = intel_panel_detect(dev_priv); if (status == connector_status_unknown) status = connector_status_connected; @@ -4289,14 +4406,14 @@ static bool bxt_digital_port_connected(struct drm_i915_private *dev_priv, * * Return %true if @port is connected, %false otherwise. */ -static bool intel_digital_port_connected(struct drm_i915_private *dev_priv, - struct intel_digital_port *port) +bool intel_digital_port_connected(struct drm_i915_private *dev_priv, + struct intel_digital_port *port) { if (HAS_PCH_IBX(dev_priv)) return ibx_digital_port_connected(dev_priv, port); else if (HAS_PCH_SPLIT(dev_priv)) return cpt_digital_port_connected(dev_priv, port); - else if (IS_BROXTON(dev_priv)) + else if (IS_GEN9_LP(dev_priv)) return bxt_digital_port_connected(dev_priv, port); else if (IS_GM45(dev_priv)) return gm45_digital_port_connected(dev_priv, port); @@ -4373,9 +4490,7 @@ intel_dp_long_pulse(struct intel_connector *intel_connector) status = connector_status_disconnected; if (status == connector_status_disconnected) { - intel_dp->compliance_test_active = 0; - intel_dp->compliance_test_type = 0; - intel_dp->compliance_test_data = 0; + memset(&intel_dp->compliance, 0, sizeof(intel_dp->compliance)); if (intel_dp->is_mst) { DRM_DEBUG_KMS("MST device may have disappeared %d vs %d\n", @@ -4396,6 +4511,12 @@ intel_dp_long_pulse(struct intel_connector *intel_connector) yesno(intel_dp_source_supports_hbr2(intel_dp)), yesno(drm_dp_tps3_supported(intel_dp->dpcd))); + /* Set the max lane count for sink */ + intel_dp->max_sink_lane_count = drm_dp_max_lane_count(intel_dp->dpcd); + + /* Set the max link BW for sink */ + intel_dp->max_sink_link_bw = intel_dp_max_link_bw(intel_dp); + intel_dp_print_rates(intel_dp); intel_dp_read_desc(intel_dp); @@ -4751,27 +4872,41 @@ static void intel_edp_panel_vdd_sanitize(struct intel_dp *intel_dp) edp_panel_vdd_schedule_off(intel_dp); } +static enum pipe vlv_active_pipe(struct intel_dp *intel_dp) +{ + struct drm_i915_private *dev_priv = to_i915(intel_dp_to_dev(intel_dp)); + + if ((intel_dp->DP & DP_PORT_EN) == 0) + return INVALID_PIPE; + + if (IS_CHERRYVIEW(dev_priv)) + return DP_PORT_TO_PIPE_CHV(intel_dp->DP); + else + return PORT_TO_PIPE(intel_dp->DP); +} + void intel_dp_encoder_reset(struct drm_encoder *encoder) { struct drm_i915_private *dev_priv = to_i915(encoder->dev); - struct intel_digital_port *intel_dig_port = enc_to_dig_port(encoder); - struct intel_lspcon *lspcon = &intel_dig_port->lspcon; - struct intel_dp *intel_dp = &intel_dig_port->dp; + struct intel_dp *intel_dp = enc_to_intel_dp(encoder); + struct intel_lspcon *lspcon = dp_to_lspcon(intel_dp); if (!HAS_DDI(dev_priv)) intel_dp->DP = I915_READ(intel_dp->output_reg); - if (IS_GEN9(dev_priv) && lspcon->active) + if (lspcon->active) lspcon_resume(lspcon); - if (to_intel_encoder(encoder)->type != INTEL_OUTPUT_EDP) - return; - pps_lock(intel_dp); - /* Reinit the power sequencer, in case BIOS did something with it. */ - intel_dp_pps_init(encoder->dev, intel_dp); - intel_edp_panel_vdd_sanitize(intel_dp); + if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) + intel_dp->active_pipe = vlv_active_pipe(intel_dp); + + if (is_edp(intel_dp)) { + /* Reinit the power sequencer, in case BIOS did something with it. */ + intel_dp_pps_init(encoder->dev, intel_dp); + intel_edp_panel_vdd_sanitize(intel_dp); + } pps_unlock(intel_dp); } @@ -4879,7 +5014,7 @@ bool intel_dp_is_edp(struct drm_i915_private *dev_priv, enum port port) if (INTEL_GEN(dev_priv) < 5) return false; - if (port == PORT_A) + if (INTEL_GEN(dev_priv) < 9 && port == PORT_A) return true; return intel_bios_is_port_edp(dev_priv, port); @@ -4926,7 +5061,7 @@ intel_pps_readout_hw_state(struct drm_i915_private *dev_priv, pp_on = I915_READ(regs.pp_on); pp_off = I915_READ(regs.pp_off); - if (!IS_BROXTON(dev_priv)) { + if (!IS_GEN9_LP(dev_priv)) { I915_WRITE(regs.pp_ctrl, pp_ctl); pp_div = I915_READ(regs.pp_div); } @@ -4944,7 +5079,7 @@ intel_pps_readout_hw_state(struct drm_i915_private *dev_priv, seq->t10 = (pp_off & PANEL_POWER_DOWN_DELAY_MASK) >> PANEL_POWER_DOWN_DELAY_SHIFT; - if (IS_BROXTON(dev_priv)) { + if (IS_GEN9_LP(dev_priv)) { u16 tmp = (pp_ctl & BXT_POWER_CYCLE_DELAY_MASK) >> BXT_POWER_CYCLE_DELAY_SHIFT; if (tmp > 0) @@ -5101,7 +5236,7 @@ intel_dp_init_panel_power_sequencer_registers(struct drm_device *dev, (seq->t10 << PANEL_POWER_DOWN_DELAY_SHIFT); /* Compute the divisor for the pp clock, simply match the Bspec * formula. */ - if (IS_BROXTON(dev_priv)) { + if (IS_GEN9_LP(dev_priv)) { pp_div = I915_READ(regs.pp_ctrl); pp_div &= ~BXT_POWER_CYCLE_DELAY_MASK; pp_div |= (DIV_ROUND_UP((seq->t11_t12 + 1), 1000) @@ -5127,7 +5262,7 @@ intel_dp_init_panel_power_sequencer_registers(struct drm_device *dev, I915_WRITE(regs.pp_on, pp_on); I915_WRITE(regs.pp_off, pp_off); - if (IS_BROXTON(dev_priv)) + if (IS_GEN9_LP(dev_priv)) I915_WRITE(regs.pp_ctrl, pp_div); else I915_WRITE(regs.pp_div, pp_div); @@ -5135,7 +5270,7 @@ intel_dp_init_panel_power_sequencer_registers(struct drm_device *dev, DRM_DEBUG_KMS("panel power sequencer register settings: PP_ON %#x, PP_OFF %#x, PP_DIV %#x\n", I915_READ(regs.pp_on), I915_READ(regs.pp_off), - IS_BROXTON(dev_priv) ? + IS_GEN9_LP(dev_priv) ? (I915_READ(regs.pp_ctrl) & BXT_POWER_CYCLE_DELAY_MASK) : I915_READ(regs.pp_div)); } @@ -5515,7 +5650,7 @@ intel_dp_drrs_init(struct intel_connector *intel_connector, } downclock_mode = intel_find_panel_downclock - (dev, fixed_mode, connector); + (dev_priv, fixed_mode, connector); if (!downclock_mode) { DRM_DEBUG_KMS("Downclock mode is not found. DRRS not supported\n"); @@ -5624,10 +5759,7 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp, * If the current pipe isn't valid, try the PPS pipe, and if that * fails just assume pipe A. */ - if (IS_CHERRYVIEW(dev_priv)) - pipe = DP_PORT_TO_PIPE_CHV(intel_dp->DP); - else - pipe = PORT_TO_PIPE(intel_dp->DP); + pipe = vlv_active_pipe(intel_dp); if (pipe != PIPE_A && pipe != PIPE_B) pipe = intel_dp->pps_pipe; @@ -5676,6 +5808,7 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port, return false; intel_dp->pps_pipe = INVALID_PIPE; + intel_dp->active_pipe = INVALID_PIPE; /* intel_dp vfuncs */ if (INTEL_GEN(dev_priv) >= 9) @@ -5704,6 +5837,9 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port, else type = DRM_MODE_CONNECTOR_DisplayPort; + if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) + intel_dp->active_pipe = vlv_active_pipe(intel_dp); + /* * For eDP we always set the encoder type to INTEL_OUTPUT_EDP, but * for DP the encoder type can be set by the caller to @@ -5793,11 +5929,10 @@ fail: return false; } -bool intel_dp_init(struct drm_device *dev, +bool intel_dp_init(struct drm_i915_private *dev_priv, i915_reg_t output_reg, enum port port) { - struct drm_i915_private *dev_priv = to_i915(dev); struct intel_digital_port *intel_dig_port; struct intel_encoder *intel_encoder; struct drm_encoder *encoder; @@ -5814,8 +5949,9 @@ bool intel_dp_init(struct drm_device *dev, intel_encoder = &intel_dig_port->base; encoder = &intel_encoder->base; - if (drm_encoder_init(dev, &intel_encoder->base, &intel_dp_enc_funcs, - DRM_MODE_ENCODER_TMDS, "DP %c", port_name(port))) + if (drm_encoder_init(&dev_priv->drm, &intel_encoder->base, + &intel_dp_enc_funcs, DRM_MODE_ENCODER_TMDS, + "DP %c", port_name(port))) goto err_encoder_init; intel_encoder->compute_config = intel_dp_compute_config; |