diff options
Diffstat (limited to 'drivers/gpu/drm/gma500/psb_intel_reg.h')
-rw-r--r-- | drivers/gpu/drm/gma500/psb_intel_reg.h | 155 |
1 files changed, 155 insertions, 0 deletions
diff --git a/drivers/gpu/drm/gma500/psb_intel_reg.h b/drivers/gpu/drm/gma500/psb_intel_reg.h index 8e8c8ef..d3091fc 100644 --- a/drivers/gpu/drm/gma500/psb_intel_reg.h +++ b/drivers/gpu/drm/gma500/psb_intel_reg.h @@ -1347,5 +1347,160 @@ No status bits are changed. #define LANE_PLL_ENABLE (0x3 << 20) #define LANE_PLL_PIPE(p) (((p) == 0) ? (1 << 21) : (0 << 21)) +#define DP_B 0x64100 +#define DP_C 0x64200 + +#define DP_PORT_EN (1 << 31) +#define DP_PIPEB_SELECT (1 << 30) +#define DP_PIPE_MASK (1 << 30) + +/* Link training mode - select a suitable mode for each stage */ +#define DP_LINK_TRAIN_PAT_1 (0 << 28) +#define DP_LINK_TRAIN_PAT_2 (1 << 28) +#define DP_LINK_TRAIN_PAT_IDLE (2 << 28) +#define DP_LINK_TRAIN_OFF (3 << 28) +#define DP_LINK_TRAIN_MASK (3 << 28) +#define DP_LINK_TRAIN_SHIFT 28 + +/* Signal voltages. These are mostly controlled by the other end */ +#define DP_VOLTAGE_0_4 (0 << 25) +#define DP_VOLTAGE_0_6 (1 << 25) +#define DP_VOLTAGE_0_8 (2 << 25) +#define DP_VOLTAGE_1_2 (3 << 25) +#define DP_VOLTAGE_MASK (7 << 25) +#define DP_VOLTAGE_SHIFT 25 + +/* Signal pre-emphasis levels, like voltages, the other end tells us what + * they want + */ +#define DP_PRE_EMPHASIS_0 (0 << 22) +#define DP_PRE_EMPHASIS_3_5 (1 << 22) +#define DP_PRE_EMPHASIS_6 (2 << 22) +#define DP_PRE_EMPHASIS_9_5 (3 << 22) +#define DP_PRE_EMPHASIS_MASK (7 << 22) +#define DP_PRE_EMPHASIS_SHIFT 22 + +/* How many wires to use. I guess 3 was too hard */ +#define DP_PORT_WIDTH_1 (0 << 19) +#define DP_PORT_WIDTH_2 (1 << 19) +#define DP_PORT_WIDTH_4 (3 << 19) +#define DP_PORT_WIDTH_MASK (7 << 19) + +/* Mystic DPCD version 1.1 special mode */ +#define DP_ENHANCED_FRAMING (1 << 18) + +/** locked once port is enabled */ +#define DP_PORT_REVERSAL (1 << 15) + +/** sends the clock on lane 15 of the PEG for debug */ +#define DP_CLOCK_OUTPUT_ENABLE (1 << 13) + +#define DP_SCRAMBLING_DISABLE (1 << 12) +#define DP_SCRAMBLING_DISABLE_IRONLAKE (1 << 7) + +/** limit RGB values to avoid confusing TVs */ +#define DP_COLOR_RANGE_16_235 (1 << 8) + +/** Turn on the audio link */ +#define DP_AUDIO_OUTPUT_ENABLE (1 << 6) + +/** vs and hs sync polarity */ +#define DP_SYNC_VS_HIGH (1 << 4) +#define DP_SYNC_HS_HIGH (1 << 3) + +/** A fantasy */ +#define DP_DETECTED (1 << 2) + +/** The aux channel provides a way to talk to the + * signal sink for DDC etc. Max packet size supported + * is 20 bytes in each direction, hence the 5 fixed + * data registers + */ +#define DPB_AUX_CH_CTL 0x64110 +#define DPB_AUX_CH_DATA1 0x64114 +#define DPB_AUX_CH_DATA2 0x64118 +#define DPB_AUX_CH_DATA3 0x6411c +#define DPB_AUX_CH_DATA4 0x64120 +#define DPB_AUX_CH_DATA5 0x64124 + +#define DPC_AUX_CH_CTL 0x64210 +#define DPC_AUX_CH_DATA1 0x64214 +#define DPC_AUX_CH_DATA2 0x64218 +#define DPC_AUX_CH_DATA3 0x6421c +#define DPC_AUX_CH_DATA4 0x64220 +#define DPC_AUX_CH_DATA5 0x64224 + +#define DP_AUX_CH_CTL_SEND_BUSY (1 << 31) +#define DP_AUX_CH_CTL_DONE (1 << 30) +#define DP_AUX_CH_CTL_INTERRUPT (1 << 29) +#define DP_AUX_CH_CTL_TIME_OUT_ERROR (1 << 28) +#define DP_AUX_CH_CTL_TIME_OUT_400us (0 << 26) +#define DP_AUX_CH_CTL_TIME_OUT_600us (1 << 26) +#define DP_AUX_CH_CTL_TIME_OUT_800us (2 << 26) +#define DP_AUX_CH_CTL_TIME_OUT_1600us (3 << 26) +#define DP_AUX_CH_CTL_TIME_OUT_MASK (3 << 26) +#define DP_AUX_CH_CTL_RECEIVE_ERROR (1 << 25) +#define DP_AUX_CH_CTL_MESSAGE_SIZE_MASK (0x1f << 20) +#define DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT 20 +#define DP_AUX_CH_CTL_PRECHARGE_2US_MASK (0xf << 16) +#define DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT 16 +#define DP_AUX_CH_CTL_AUX_AKSV_SELECT (1 << 15) +#define DP_AUX_CH_CTL_MANCHESTER_TEST (1 << 14) +#define DP_AUX_CH_CTL_SYNC_TEST (1 << 13) +#define DP_AUX_CH_CTL_DEGLITCH_TEST (1 << 12) +#define DP_AUX_CH_CTL_PRECHARGE_TEST (1 << 11) +#define DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK (0x7ff) +#define DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT 0 + +/* + * Computing GMCH M and N values for the Display Port link + * + * GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes + * + * ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz) + * + * The GMCH value is used internally + * + * bytes_per_pixel is the number of bytes coming out of the plane, + * which is after the LUTs, so we want the bytes for our color format. + * For our current usage, this is always 3, one byte for R, G and B. + */ + +#define _PIPEA_GMCH_DATA_M 0x70050 +#define _PIPEB_GMCH_DATA_M 0x71050 + +/* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */ +#define PIPE_GMCH_DATA_M_TU_SIZE_MASK (0x3f << 25) +#define PIPE_GMCH_DATA_M_TU_SIZE_SHIFT 25 + +#define PIPE_GMCH_DATA_M_MASK (0xffffff) + +#define _PIPEA_GMCH_DATA_N 0x70054 +#define _PIPEB_GMCH_DATA_N 0x71054 +#define PIPE_GMCH_DATA_N_MASK (0xffffff) + +/* + * Computing Link M and N values for the Display Port link + * + * Link M / N = pixel_clock / ls_clk + * + * (the DP spec calls pixel_clock the 'strm_clk') + * + * The Link value is transmitted in the Main Stream + * Attributes and VB-ID. + */ + +#define _PIPEA_DP_LINK_M 0x70060 +#define _PIPEB_DP_LINK_M 0x71060 +#define PIPEA_DP_LINK_M_MASK (0xffffff) + +#define _PIPEA_DP_LINK_N 0x70064 +#define _PIPEB_DP_LINK_N 0x71064 +#define PIPEA_DP_LINK_N_MASK (0xffffff) + +#define PIPE_GMCH_DATA_M(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_M, _PIPEB_GMCH_DATA_M) +#define PIPE_GMCH_DATA_N(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_N, _PIPEB_GMCH_DATA_N) +#define PIPE_DP_LINK_M(pipe) _PIPE(pipe, _PIPEA_DP_LINK_M, _PIPEB_DP_LINK_M) +#define PIPE_DP_LINK_N(pipe) _PIPE(pipe, _PIPEA_DP_LINK_N, _PIPEB_DP_LINK_N) #endif |