diff options
Diffstat (limited to 'drivers/char/mxser_new.h')
-rw-r--r-- | drivers/char/mxser_new.h | 293 |
1 files changed, 0 insertions, 293 deletions
diff --git a/drivers/char/mxser_new.h b/drivers/char/mxser_new.h deleted file mode 100644 index d42f776..0000000 --- a/drivers/char/mxser_new.h +++ /dev/null @@ -1,293 +0,0 @@ -#ifndef _MXSER_H -#define _MXSER_H - -/* - * Semi-public control interfaces - */ - -/* - * MOXA ioctls - */ - -#define MOXA 0x400 -#define MOXA_GETDATACOUNT (MOXA + 23) -#define MOXA_GET_CONF (MOXA + 35) -#define MOXA_DIAGNOSE (MOXA + 50) -#define MOXA_CHKPORTENABLE (MOXA + 60) -#define MOXA_HighSpeedOn (MOXA + 61) -#define MOXA_GET_MAJOR (MOXA + 63) -#define MOXA_GET_CUMAJOR (MOXA + 64) -#define MOXA_GETMSTATUS (MOXA + 65) -#define MOXA_SET_OP_MODE (MOXA + 66) -#define MOXA_GET_OP_MODE (MOXA + 67) - -#define RS232_MODE 0 -#define RS485_2WIRE_MODE 1 -#define RS422_MODE 2 -#define RS485_4WIRE_MODE 3 -#define OP_MODE_MASK 3 - -#define MOXA_SDS_RSTICOUNTER (MOXA + 69) -#define MOXA_ASPP_OQUEUE (MOXA + 70) -#define MOXA_ASPP_SETBAUD (MOXA + 71) -#define MOXA_ASPP_GETBAUD (MOXA + 72) -#define MOXA_ASPP_MON (MOXA + 73) -#define MOXA_ASPP_LSTATUS (MOXA + 74) -#define MOXA_ASPP_MON_EXT (MOXA + 75) -#define MOXA_SET_BAUD_METHOD (MOXA + 76) -#define MOXA_SET_SPECIAL_BAUD_RATE (MOXA + 77) -#define MOXA_GET_SPECIAL_BAUD_RATE (MOXA + 78) - -/* --------------------------------------------------- */ - -#define NPPI_NOTIFY_PARITY 0x01 -#define NPPI_NOTIFY_FRAMING 0x02 -#define NPPI_NOTIFY_HW_OVERRUN 0x04 -#define NPPI_NOTIFY_SW_OVERRUN 0x08 -#define NPPI_NOTIFY_BREAK 0x10 - -#define NPPI_NOTIFY_CTSHOLD 0x01 /* Tx hold by CTS low */ -#define NPPI_NOTIFY_DSRHOLD 0x02 /* Tx hold by DSR low */ -#define NPPI_NOTIFY_XOFFHOLD 0x08 /* Tx hold by Xoff received */ -#define NPPI_NOTIFY_XOFFXENT 0x10 /* Xoff Sent */ - -/* follow just for Moxa Must chip define. */ -/* */ -/* when LCR register (offset 0x03) write following value, */ -/* the Must chip will enter enchance mode. And write value */ -/* on EFR (offset 0x02) bit 6,7 to change bank. */ -#define MOXA_MUST_ENTER_ENCHANCE 0xBF - -/* when enhance mode enable, access on general bank register */ -#define MOXA_MUST_GDL_REGISTER 0x07 -#define MOXA_MUST_GDL_MASK 0x7F -#define MOXA_MUST_GDL_HAS_BAD_DATA 0x80 - -#define MOXA_MUST_LSR_RERR 0x80 /* error in receive FIFO */ -/* enchance register bank select and enchance mode setting register */ -/* when LCR register equal to 0xBF */ -#define MOXA_MUST_EFR_REGISTER 0x02 -/* enchance mode enable */ -#define MOXA_MUST_EFR_EFRB_ENABLE 0x10 -/* enchance reister bank set 0, 1, 2 */ -#define MOXA_MUST_EFR_BANK0 0x00 -#define MOXA_MUST_EFR_BANK1 0x40 -#define MOXA_MUST_EFR_BANK2 0x80 -#define MOXA_MUST_EFR_BANK3 0xC0 -#define MOXA_MUST_EFR_BANK_MASK 0xC0 - -/* set XON1 value register, when LCR=0xBF and change to bank0 */ -#define MOXA_MUST_XON1_REGISTER 0x04 - -/* set XON2 value register, when LCR=0xBF and change to bank0 */ -#define MOXA_MUST_XON2_REGISTER 0x05 - -/* set XOFF1 value register, when LCR=0xBF and change to bank0 */ -#define MOXA_MUST_XOFF1_REGISTER 0x06 - -/* set XOFF2 value register, when LCR=0xBF and change to bank0 */ -#define MOXA_MUST_XOFF2_REGISTER 0x07 - -#define MOXA_MUST_RBRTL_REGISTER 0x04 -#define MOXA_MUST_RBRTH_REGISTER 0x05 -#define MOXA_MUST_RBRTI_REGISTER 0x06 -#define MOXA_MUST_THRTL_REGISTER 0x07 -#define MOXA_MUST_ENUM_REGISTER 0x04 -#define MOXA_MUST_HWID_REGISTER 0x05 -#define MOXA_MUST_ECR_REGISTER 0x06 -#define MOXA_MUST_CSR_REGISTER 0x07 - -/* good data mode enable */ -#define MOXA_MUST_FCR_GDA_MODE_ENABLE 0x20 -/* only good data put into RxFIFO */ -#define MOXA_MUST_FCR_GDA_ONLY_ENABLE 0x10 - -/* enable CTS interrupt */ -#define MOXA_MUST_IER_ECTSI 0x80 -/* enable RTS interrupt */ -#define MOXA_MUST_IER_ERTSI 0x40 -/* enable Xon/Xoff interrupt */ -#define MOXA_MUST_IER_XINT 0x20 -/* enable GDA interrupt */ -#define MOXA_MUST_IER_EGDAI 0x10 - -#define MOXA_MUST_RECV_ISR (UART_IER_RDI | MOXA_MUST_IER_EGDAI) - -/* GDA interrupt pending */ -#define MOXA_MUST_IIR_GDA 0x1C -#define MOXA_MUST_IIR_RDA 0x04 -#define MOXA_MUST_IIR_RTO 0x0C -#define MOXA_MUST_IIR_LSR 0x06 - -/* recieved Xon/Xoff or specical interrupt pending */ -#define MOXA_MUST_IIR_XSC 0x10 - -/* RTS/CTS change state interrupt pending */ -#define MOXA_MUST_IIR_RTSCTS 0x20 -#define MOXA_MUST_IIR_MASK 0x3E - -#define MOXA_MUST_MCR_XON_FLAG 0x40 -#define MOXA_MUST_MCR_XON_ANY 0x80 -#define MOXA_MUST_MCR_TX_XON 0x08 - -/* software flow control on chip mask value */ -#define MOXA_MUST_EFR_SF_MASK 0x0F -/* send Xon1/Xoff1 */ -#define MOXA_MUST_EFR_SF_TX1 0x08 -/* send Xon2/Xoff2 */ -#define MOXA_MUST_EFR_SF_TX2 0x04 -/* send Xon1,Xon2/Xoff1,Xoff2 */ -#define MOXA_MUST_EFR_SF_TX12 0x0C -/* don't send Xon/Xoff */ -#define MOXA_MUST_EFR_SF_TX_NO 0x00 -/* Tx software flow control mask */ -#define MOXA_MUST_EFR_SF_TX_MASK 0x0C -/* don't receive Xon/Xoff */ -#define MOXA_MUST_EFR_SF_RX_NO 0x00 -/* receive Xon1/Xoff1 */ -#define MOXA_MUST_EFR_SF_RX1 0x02 -/* receive Xon2/Xoff2 */ -#define MOXA_MUST_EFR_SF_RX2 0x01 -/* receive Xon1,Xon2/Xoff1,Xoff2 */ -#define MOXA_MUST_EFR_SF_RX12 0x03 -/* Rx software flow control mask */ -#define MOXA_MUST_EFR_SF_RX_MASK 0x03 - -#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr |= MOXA_MUST_EFR_EFRB_ENABLE; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_XON1_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_XOFF1_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_FIFO_VALUE(info) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((info)->ioaddr+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (info)->ioaddr+UART_LCR);\ - __efr = inb((info)->ioaddr+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (info)->ioaddr+MOXA_MUST_EFR_REGISTER); \ - outb((u8)((info)->rx_high_water), (info)->ioaddr+ \ - MOXA_MUST_RBRTH_REGISTER); \ - outb((u8)((info)->rx_trigger), (info)->ioaddr+ \ - MOXA_MUST_RBRTI_REGISTER); \ - outb((u8)((info)->rx_low_water), (info)->ioaddr+ \ - MOXA_MUST_RBRTL_REGISTER); \ - outb(__oldlcr, (info)->ioaddr+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_ENUM_VALUE(baseio, Value) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK2; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_ENUM_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK2; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - *pId = inb((baseio)+MOXA_MUST_HWID_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ - __efr |= MOXA_MUST_EFR_SF_TX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ - __efr |= MOXA_MUST_EFR_SF_RX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#endif |