diff options
Diffstat (limited to 'drivers/block/cciss.c')
| -rw-r--r-- | drivers/block/cciss.c | 136 |
1 files changed, 64 insertions, 72 deletions
diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c index 2cc4dda4..8e0f925 100644 --- a/drivers/block/cciss.c +++ b/drivers/block/cciss.c @@ -66,6 +66,7 @@ MODULE_VERSION("3.6.26"); MODULE_LICENSE("GPL"); static DEFINE_MUTEX(cciss_mutex); +static struct proc_dir_entry *proc_cciss; #include "cciss_cmd.h" #include "cciss.h" @@ -113,6 +114,8 @@ static struct board_type products[] = { {0x409D0E11, "Smart Array 6400 EM", &SA5_access}, {0x40910E11, "Smart Array 6i", &SA5_access}, {0x3225103C, "Smart Array P600", &SA5_access}, + {0x3223103C, "Smart Array P800", &SA5_access}, + {0x3234103C, "Smart Array P400", &SA5_access}, {0x3235103C, "Smart Array P400i", &SA5_access}, {0x3211103C, "Smart Array E200i", &SA5_access}, {0x3212103C, "Smart Array E200", &SA5_access}, @@ -361,8 +364,6 @@ static const char *raid_label[] = { "0", "4", "1(1+0)", "5", "5+1", "ADG", #define ENG_GIG_FACTOR (ENG_GIG/512) #define ENGAGE_SCSI "engage scsi" -static struct proc_dir_entry *proc_cciss; - static void cciss_seq_show_header(struct seq_file *seq) { ctlr_info_t *h = seq->private; @@ -2833,6 +2834,8 @@ static int cciss_revalidate(struct gendisk *disk) InquiryData_struct *inq_buff = NULL; for (logvol = 0; logvol < CISS_MAX_LUN; logvol++) { + if (!h->drv[logvol]) + continue; if (memcmp(h->drv[logvol]->LunID, drv->LunID, sizeof(drv->LunID)) == 0) { FOUND = 1; @@ -3753,7 +3756,7 @@ static void __devinit cciss_wait_for_mode_change_ack(ctlr_info_t *h) for (i = 0; i < MAX_CONFIG_WAIT; i++) { if (!(readl(h->vaddr + SA5_DOORBELL) & CFGTBL_ChangeReq)) break; - msleep(10); + usleep_range(10000, 20000); } } @@ -3937,10 +3940,9 @@ static int __devinit cciss_lookup_board_id(struct pci_dev *pdev, u32 *board_id) *board_id = ((subsystem_device_id << 16) & 0xffff0000) | subsystem_vendor_id; - for (i = 0; i < ARRAY_SIZE(products); i++) { + for (i = 0; i < ARRAY_SIZE(products); i++) if (*board_id == products[i].board_id) return i; - } dev_warn(&pdev->dev, "unrecognized board ID: 0x%08x, ignoring.\n", *board_id); return -ENODEV; @@ -3971,18 +3973,31 @@ static int __devinit cciss_pci_find_memory_BAR(struct pci_dev *pdev, return -ENODEV; } -static int __devinit cciss_wait_for_board_ready(ctlr_info_t *h) +static int __devinit cciss_wait_for_board_state(struct pci_dev *pdev, + void __iomem *vaddr, int wait_for_ready) +#define BOARD_READY 1 +#define BOARD_NOT_READY 0 { - int i; + int i, iterations; u32 scratchpad; - for (i = 0; i < CCISS_BOARD_READY_ITERATIONS; i++) { - scratchpad = readl(h->vaddr + SA5_SCRATCHPAD_OFFSET); - if (scratchpad == CCISS_FIRMWARE_READY) - return 0; + if (wait_for_ready) + iterations = CCISS_BOARD_READY_ITERATIONS; + else + iterations = CCISS_BOARD_NOT_READY_ITERATIONS; + + for (i = 0; i < iterations; i++) { + scratchpad = readl(vaddr + SA5_SCRATCHPAD_OFFSET); + if (wait_for_ready) { + if (scratchpad == CCISS_FIRMWARE_READY) + return 0; + } else { + if (scratchpad != CCISS_FIRMWARE_READY) + return 0; + } msleep(CCISS_BOARD_READY_POLL_INTERVAL_MSECS); } - dev_warn(&h->pdev->dev, "board not ready, timed out.\n"); + dev_warn(&pdev->dev, "board not ready, timed out.\n"); return -ENODEV; } @@ -4031,6 +4046,11 @@ static int __devinit cciss_find_cfgtables(ctlr_info_t *h) static void __devinit cciss_get_max_perf_mode_cmds(struct ctlr_info *h) { h->max_commands = readl(&(h->cfgtable->MaxPerformantModeCommands)); + + /* Limit commands in memory limited kdump scenario. */ + if (reset_devices && h->max_commands > 32) + h->max_commands = 32; + if (h->max_commands < 16) { dev_warn(&h->pdev->dev, "Controller reports " "max supported commands of %d, an obvious lie. " @@ -4148,7 +4168,7 @@ static int __devinit cciss_pci_init(ctlr_info_t *h) err = -ENOMEM; goto err_out_free_res; } - err = cciss_wait_for_board_ready(h); + err = cciss_wait_for_board_state(h->pdev, h->vaddr, BOARD_READY); if (err) goto err_out_free_res; err = cciss_find_cfgtables(h); @@ -4313,36 +4333,6 @@ static __devinit int cciss_message(struct pci_dev *pdev, unsigned char opcode, u #define cciss_soft_reset_controller(p) cciss_message(p, 1, 0) #define cciss_noop(p) cciss_message(p, 3, 0) -static __devinit int cciss_reset_msi(struct pci_dev *pdev) -{ -/* the #defines are stolen from drivers/pci/msi.h. */ -#define msi_control_reg(base) (base + PCI_MSI_FLAGS) -#define PCI_MSIX_FLAGS_ENABLE (1 << 15) - - int pos; - u16 control = 0; - - pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); - if (pos) { - pci_read_config_word(pdev, msi_control_reg(pos), &control); - if (control & PCI_MSI_FLAGS_ENABLE) { - dev_info(&pdev->dev, "resetting MSI\n"); - pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSI_FLAGS_ENABLE); - } - } - - pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX); - if (pos) { - pci_read_config_word(pdev, msi_control_reg(pos), &control); - if (control & PCI_MSIX_FLAGS_ENABLE) { - dev_info(&pdev->dev, "resetting MSI-X\n"); - pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSIX_FLAGS_ENABLE); - } - } - - return 0; -} - static int cciss_controller_hard_reset(struct pci_dev *pdev, void * __iomem vaddr, bool use_doorbell) { @@ -4397,17 +4387,17 @@ static int cciss_controller_hard_reset(struct pci_dev *pdev, * states or using the doorbell register. */ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev) { - u16 saved_config_space[32]; u64 cfg_offset; u32 cfg_base_addr; u64 cfg_base_addr_index; void __iomem *vaddr; unsigned long paddr; u32 misc_fw_support, active_transport; - int rc, i; + int rc; CfgTable_struct __iomem *cfgtable; bool use_doorbell; u32 board_id; + u16 command_register; /* For controllers as old a the p600, this is very nearly * the same thing as @@ -4417,14 +4407,6 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev) * pci_set_power_state(pci_dev, PCI_D0); * pci_restore_state(pci_dev); * - * but we can't use these nice canned kernel routines on - * kexec, because they also check the MSI/MSI-X state in PCI - * configuration space and do the wrong thing when it is - * set/cleared. Also, the pci_save/restore_state functions - * violate the ordering requirements for restoring the - * configuration space from the CCISS document (see the - * comment below). So we roll our own .... - * * For controllers newer than the P600, the pci power state * method of resetting doesn't work so we have another way * using the doorbell register. @@ -4443,8 +4425,13 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev) return -ENODEV; } - for (i = 0; i < 32; i++) - pci_read_config_word(pdev, 2*i, &saved_config_space[i]); + /* Save the PCI command register */ + pci_read_config_word(pdev, 4, &command_register); + /* Turn the board off. This is so that later pci_restore_state() + * won't turn the board on before the rest of config space is ready. + */ + pci_disable_device(pdev); + pci_save_state(pdev); /* find the first memory BAR, so we can find the cfg table */ rc = cciss_pci_find_memory_BAR(pdev, &paddr); @@ -4479,26 +4466,32 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev) rc = cciss_controller_hard_reset(pdev, vaddr, use_doorbell); if (rc) goto unmap_cfgtable; - - /* Restore the PCI configuration space. The Open CISS - * Specification says, "Restore the PCI Configuration - * Registers, offsets 00h through 60h. It is important to - * restore the command register, 16-bits at offset 04h, - * last. Do not restore the configuration status register, - * 16-bits at offset 06h." Note that the offset is 2*i. - */ - for (i = 0; i < 32; i++) { - if (i == 2 || i == 3) - continue; - pci_write_config_word(pdev, 2*i, saved_config_space[i]); + pci_restore_state(pdev); + rc = pci_enable_device(pdev); + if (rc) { + dev_warn(&pdev->dev, "failed to enable device.\n"); + goto unmap_cfgtable; } - wmb(); - pci_write_config_word(pdev, 4, saved_config_space[2]); + pci_write_config_word(pdev, 4, command_register); /* Some devices (notably the HP Smart Array 5i Controller) need a little pause here */ msleep(CCISS_POST_RESET_PAUSE_MSECS); + /* Wait for board to become not ready, then ready. */ + dev_info(&pdev->dev, "Waiting for board to become ready.\n"); + rc = cciss_wait_for_board_state(pdev, vaddr, BOARD_NOT_READY); + if (rc) /* Don't bail, might be E500, etc. which can't be reset */ + dev_warn(&pdev->dev, + "failed waiting for board to become not ready\n"); + rc = cciss_wait_for_board_state(pdev, vaddr, BOARD_READY); + if (rc) { + dev_warn(&pdev->dev, + "failed waiting for board to become ready\n"); + goto unmap_cfgtable; + } + dev_info(&pdev->dev, "board ready.\n"); + /* Controller should be in simple mode at this point. If it's not, * It means we're on one of those controllers which doesn't support * the doorbell reset method and on which the PCI power management reset @@ -4539,8 +4532,6 @@ static __devinit int cciss_init_reset_devices(struct pci_dev *pdev) return 0; /* just try to do the kdump anyhow. */ if (rc) return -ENODEV; - if (cciss_reset_msi(pdev)) - return -ENODEV; /* Now try to get the controller to respond to a no-op */ for (i = 0; i < CCISS_POST_RESET_NOOP_RETRIES; i++) { @@ -4936,7 +4927,8 @@ static void __exit cciss_cleanup(void) } } kthread_stop(cciss_scan_thread); - remove_proc_entry("driver/cciss", NULL); + if (proc_cciss) + remove_proc_entry("driver/cciss", NULL); bus_unregister(&cciss_bus_type); } |
