diff options
Diffstat (limited to 'drivers/ata/pata_hpt3x2n.c')
| -rw-r--r-- | drivers/ata/pata_hpt3x2n.c | 120 |
1 files changed, 56 insertions, 64 deletions
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c index dd26bc7..01457b2 100644 --- a/drivers/ata/pata_hpt3x2n.c +++ b/drivers/ata/pata_hpt3x2n.c @@ -25,7 +25,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_hpt3x2n" -#define DRV_VERSION "0.3.8" +#define DRV_VERSION "0.3.10" enum { HPT_PCI_FAST = (1 << 31), @@ -45,25 +45,24 @@ struct hpt_chip { /* key for bus clock timings * bit - * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW - * DMA. cycles = value + 1 - * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW - * DMA. cycles = value + 1 - * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file + * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA. + * cycles = value + 1 + * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA. + * cycles = value + 1 + * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file * register access. - * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file + * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file * register access. - * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. - * during task file register access. - * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA - * xfer. - * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task + * 18:20 udma_cycle_time. Clock cycles for UDMA xfer. + * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock. + * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer. + * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file * register access. - * 28 UDMA enable - * 29 DMA enable - * 30 PIO_MST enable. if set, the chip is in bus master mode during - * PIO. - * 31 FIFO enable. + * 28 UDMA enable. + * 29 DMA enable. + * 30 PIO_MST enable. If set, the chip is in bus master mode during + * PIO xfer. + * 31 FIFO enable. Only for PIO. */ /* 66MHz DPLL clocks */ @@ -161,20 +160,12 @@ static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline) return ata_sff_prereset(link, deadline); } -/** - * hpt3x2n_set_piomode - PIO setup - * @ap: ATA interface - * @adev: device on the interface - * - * Perform PIO mode setup. - */ - -static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) +static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev, + u8 mode) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u32 addr1, addr2; - u32 reg; - u32 mode; + u32 reg, timing, mask; u8 fast; addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); @@ -185,11 +176,32 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) fast &= ~0x07; pci_write_config_byte(pdev, addr2, fast); + /* Determine timing mask and find matching mode entry */ + if (mode < XFER_MW_DMA_0) + mask = 0xcfc3ffff; + else if (mode < XFER_UDMA_0) + mask = 0x31c001ff; + else + mask = 0x303c0000; + + timing = hpt3x2n_find_mode(ap, mode); + pci_read_config_dword(pdev, addr1, ®); - mode = hpt3x2n_find_mode(ap, adev->pio_mode); - mode &= 0xCFC3FFFF; /* Leave DMA bits alone */ - reg &= ~0xCFC3FFFF; /* Strip timing bits */ - pci_write_config_dword(pdev, addr1, reg | mode); + reg = (reg & ~mask) | (timing & mask); + pci_write_config_dword(pdev, addr1, reg); +} + +/** + * hpt3x2n_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Perform PIO mode setup. + */ + +static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + hpt3x2n_set_mode(ap, adev, adev->pio_mode); } /** @@ -197,32 +209,12 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) * @ap: ATA interface * @adev: Device being configured * - * Set up the channel for MWDMA or UDMA modes. Much the same as with - * PIO, load the mode number and then set MWDMA or UDMA flag. + * Set up the channel for MWDMA or UDMA modes. */ static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) { - struct pci_dev *pdev = to_pci_dev(ap->host->dev); - u32 addr1, addr2; - u32 reg, mode, mask; - u8 fast; - - addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); - addr2 = 0x51 + 4 * ap->port_no; - - /* Fast interrupt prediction disable, hold off interrupt disable */ - pci_read_config_byte(pdev, addr2, &fast); - fast &= ~0x07; - pci_write_config_byte(pdev, addr2, fast); - - mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000; - - pci_read_config_dword(pdev, addr1, ®); - mode = hpt3x2n_find_mode(ap, adev->dma_mode); - mode &= mask; - reg &= ~mask; - pci_write_config_dword(pdev, addr1, reg | mode); + hpt3x2n_set_mode(ap, adev, adev->dma_mode); } /** @@ -544,19 +536,19 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) pci_mhz); /* Set our private data up. We only need a few flags so we use it directly */ - if (pci_mhz > 60) { + if (pci_mhz > 60) hpriv = (void *)(PCI66 | USE_DPLL); - /* - * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in - * the MISC. register to stretch the UltraDMA Tss timing. - * NOTE: This register is only writeable via I/O space. - */ - if (dev->device == PCI_DEVICE_ID_TTI_HPT371) - outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c); - } + + /* + * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in + * the MISC. register to stretch the UltraDMA Tss timing. + * NOTE: This register is only writeable via I/O space. + */ + if (dev->device == PCI_DEVICE_ID_TTI_HPT371) + outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c); /* Now kick off ATA set up */ - return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv); + return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0); } static const struct pci_device_id hpt3x2n[] = { |
