summaryrefslogtreecommitdiffstats
path: root/drivers/ata/pata_efar.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ata/pata_efar.c')
-rw-r--r--drivers/ata/pata_efar.c342
1 files changed, 342 insertions, 0 deletions
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
new file mode 100644
index 0000000..c30bc18
--- /dev/null
+++ b/drivers/ata/pata_efar.c
@@ -0,0 +1,342 @@
+/*
+ * pata_efar.c - EFAR PIIX clone controller driver
+ *
+ * (C) 2005 Red Hat <alan@redhat.com>
+ *
+ * Some parts based on ata_piix.c by Jeff Garzik and others.
+ *
+ * The EFAR is a PIIX4 clone with UDMA66 support. Unlike the later
+ * Intel ICH controllers the EFAR widened the UDMA mode register bits
+ * and doesn't require the funky clock selection.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME "pata_efar"
+#define DRV_VERSION "0.4.1"
+
+/**
+ * efar_pre_reset - check for 40/80 pin
+ * @ap: Port
+ *
+ * Perform cable detection for the EFAR ATA interface. This is
+ * different to the PIIX arrangement
+ */
+
+static int efar_pre_reset(struct ata_port *ap)
+{
+ static const struct pci_bits efar_enable_bits[] = {
+ { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
+ { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */
+ };
+
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 tmp;
+
+ if (!pci_test_config_bits(pdev, &efar_enable_bits[ap->port_no])) {
+ ata_port_disable(ap);
+ printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+ return 0;
+ }
+ pci_read_config_byte(pdev, 0x47, &tmp);
+ if (tmp & (2 >> ap->port_no))
+ ap->cbl = ATA_CBL_PATA40;
+ else
+ ap->cbl = ATA_CBL_PATA80;
+ return ata_std_prereset(ap);
+}
+
+/**
+ * efar_probe_reset - Probe specified port on PATA host controller
+ * @ap: Port to probe
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void efar_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, efar_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ * efar_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set PIO mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
+ u16 idetm_data;
+ int control = 0;
+
+ /*
+ * See Intel Document 298600-004 for the timing programing rules
+ * for PIIX/ICH. The EFAR is a clone so very similar
+ */
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ if (pio > 2)
+ control |= 1; /* TIME1 enable */
+ if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */
+ control |= 2; /* IE enable */
+ /* Intel specifies that the PPE functionality is for disk only */
+ if (adev->class == ATA_DEV_ATA)
+ control |= 4; /* PPE enable */
+
+ pci_read_config_word(dev, idetm_port, &idetm_data);
+
+ /* Enable PPE, IE and TIME as appropriate */
+
+ if (adev->devno == 0) {
+ idetm_data &= 0xCCF0;
+ idetm_data |= control;
+ idetm_data |= (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ } else {
+ int shift = 4 * ap->port_no;
+ u8 slave_data;
+
+ idetm_data &= 0xCC0F;
+ idetm_data |= (control << 4);
+
+ /* Slave timing in seperate register */
+ pci_read_config_byte(dev, 0x44, &slave_data);
+ slave_data &= 0x0F << shift;
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << shift;
+ pci_write_config_byte(dev, 0x44, slave_data);
+ }
+
+ idetm_data |= 0x4000; /* Ensure SITRE is enabled */
+ pci_write_config_word(dev, idetm_port, idetm_data);
+}
+
+/**
+ * efar_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device to program
+ *
+ * Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ u8 master_port = ap->port_no ? 0x42 : 0x40;
+ u16 master_data;
+ u8 speed = adev->dma_mode;
+ int devid = adev->devno + 2 * ap->port_no;
+ u8 udma_enable;
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ pci_read_config_word(dev, master_port, &master_data);
+ pci_read_config_byte(dev, 0x48, &udma_enable);
+
+ if (speed >= XFER_UDMA_0) {
+ unsigned int udma = adev->dma_mode - XFER_UDMA_0;
+ u16 udma_timing;
+
+ udma_enable |= (1 << devid);
+
+ /* Load the UDMA mode number */
+ pci_read_config_word(dev, 0x4A, &udma_timing);
+ udma_timing &= ~(7 << (4 * devid));
+ udma_timing |= udma << (4 * devid);
+ pci_write_config_word(dev, 0x4A, udma_timing);
+ } else {
+ /*
+ * MWDMA is driven by the PIO timings. We must also enable
+ * IORDY unconditionally along with TIME1. PPE has already
+ * been set when the PIO timing was set.
+ */
+ unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
+ unsigned int control;
+ u8 slave_data;
+ const unsigned int needed_pio[3] = {
+ XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+ };
+ int pio = needed_pio[mwdma] - XFER_PIO_0;
+
+ control = 3; /* IORDY|TIME1 */
+
+ /* If the drive MWDMA is faster than it can do PIO then
+ we must force PIO into PIO0 */
+
+ if (adev->pio_mode < needed_pio[mwdma])
+ /* Enable DMA timing only */
+ control |= 8; /* PIO cycles in PIO0 */
+
+ if (adev->devno) { /* Slave */
+ master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
+ master_data |= control << 4;
+ pci_read_config_byte(dev, 0x44, &slave_data);
+ slave_data &= (0x0F + 0xE1 * ap->port_no);
+ /* Load the matching timing */
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+ pci_write_config_byte(dev, 0x44, slave_data);
+ } else { /* Master */
+ master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY
+ and master timing bits */
+ master_data |= control;
+ master_data |=
+ (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ }
+ udma_enable &= ~(1 << devid);
+ pci_write_config_word(dev, master_port, master_data);
+ }
+ pci_write_config_byte(dev, 0x48, udma_enable);
+}
+
+static struct scsi_host_template efar_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+};
+
+static const struct ata_port_operations efar_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = efar_set_piomode,
+ .set_dmamode = efar_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = efar_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
+
+ .eng_timeout = ata_eng_timeout,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop,
+};
+
+
+/**
+ * efar_init_one - Register EFAR ATA PCI device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in efar_pci_tbl matching with @pdev
+ *
+ * Called from kernel PCI layer.
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version;
+ static struct ata_port_info info = {
+ .sht = &efar_sht,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma1-2 */
+ .udma_mask = 0x0f, /* UDMA 66 */
+ .port_ops = &efar_ops,
+ };
+ static struct ata_port_info *port_info[2] = { &info, &info };
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "version " DRV_VERSION "\n");
+
+ return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id efar_pci_tbl[] = {
+ { 0x1055, 0x9130, PCI_ANY_ID, PCI_ANY_ID, },
+ { } /* terminate list */
+};
+
+static struct pci_driver efar_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = efar_pci_tbl,
+ .probe = efar_init_one,
+ .remove = ata_pci_remove_one,
+};
+
+static int __init efar_init(void)
+{
+ return pci_register_driver(&efar_pci_driver);
+}
+
+static void __exit efar_exit(void)
+{
+ pci_unregister_driver(&efar_pci_driver);
+}
+
+
+module_init(efar_init);
+module_exit(efar_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for EFAR PIIX clones");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, efar_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
OpenPOWER on IntegriCloud